Professional Documents
Culture Documents
P N M T
ASOLINK
ETWORK
ANAGEMENT
ERMINAL
NEC Corporation
Copyright 2010
ROI-S06554
Table of Contents 1. 2. 3. 4. 5. 6. 7. 8. Installation Sequence ........................................................................................................ 1 Phone and Modem Options Setting (Standard 19.2Kbps Connection) ........................ 2 Installation of USB Com Port Driver (USB Connection) .............................................. 7 Dial-up Setting ................................................................................................................. 10 SNMP Service Setting ..................................................................................................... 21 PNMT Setup .................................................................................................................... 26 PNMT SetupNetwork Connections Setting on Windows XP ...................................... 31 Launching PNMT ............................................................................................................ 39
-i-
ROI-S06554
1. Installation Sequence
Only Administrator group privilege level users are authorized to configure the following settings,
(1) Dial-up Connection
Step 1: Modem Setting Network Element (NE) other than PASOLINK NEO Standard 19200bps Modem Setting (Phone and Modem Options Setting)
-1-
ROI-S06554
(2) Click the Phone and Modem Options icon in the Control Panel window to start configuring the modem.
-2-
ROI-S06554 (3) Enter your country and area code in the Location Information window. Click [OK].
-3-
ROI-S06554 (5) Select the Modem tab. Click [Add] to continue with adding the new modem for the PNMT.
(6) Check Dont detect my modem ... and click [Next] to continue.
-4-
ROI-S06554 (7) Select Standard Modem Types from the list of Manufacturers and Standard 19200bps Modem from the Models. Click [Next] to continue.
(8) Select Selected ports and COM#, then click [Next] to continue.
-5-
(10)Verify that Standard 19200 bps Modem and COM1 are displayed. Click [OK].
-6-
ROI-S06554
(2) Select Install from a list or specific location [Advanced] and click on [Next].
-7-
ROI-S06554 (3) Insert the USB driver CD-ROM in the computers disk drive and select Search for the best driver in these locations and check Search removable media [floppy, CD-ROM ...] then, click [Next].
-8-
NOTE There is a possibility that the USB connection is dropped during a long-duration operation depending on the device type of computer. In the case of a connection failure, please reestablish the dial-up connection.
-9-
ROI-S06554
4. Dial-up Setting
(1) Click Start | Settings | Control Panel and the Network Connections icon to start configuring the Dialup setting.
(2) The Network Connections window appears. Click Create a new connection in the Network Tasks area.
- 10 -
ROI-S06554
(3) The Welcome to the New Connection Wizard window appears. Click [Next].
(4) Select Connect to the network at my workplace and click [Next] to continue.
- 11 -
ROI-S06554
(6) Select Modem - Choose a connected port, and click [Next] to continue.
NOTE This screen appears only when a USB Modem Driver has been installed.
- 12 -
ROI-S06554
(7) In the New Connection Wizard window, input connection name into Company Name field. Click [Next]. In case of connecting with RS232C-Type [PNMT(RS232C)]
- 13 -
ROI-S06554
(8) Enter any number in the Phone number field and click [Next] to continue.
- 14 -
ROI-S06554
(9) You can also create a shortcut on your desktop if desired. Click [Finish]. RS232C connection
USB connection
- 15 -
ROI-S06554
(10) In the Connect Dial-up Connection window, click [Cancel] to continue. Click Properties in the Connect Dial-up Connection window.
(11) In the Properties Window click on the General tab. Click [Configure...].
RS232C setting
USB setting
- 16 -
ROI-S06554
RS232C setting
USB setting
(13) Retain the default setting on the Options tab and click the Security tab.
RS232C setting
USB setting
- 17 -
ROI-S06554
(14) Retain the default setting on the Security tab and click the Networking tab.
RS232C setting
USB setting
(15) On the Networking tab, verify that PPP ... is`displayed in the Type of dial-up server I am calling field and uncheck File and Printer ... and Client for Microsoft....
RS232C setting
USB setting
- 18 -
ROI-S06554
(16) Click Settings Uncheck all the boxes in the window that appears, as shown below. Click [OK] to go back to the previous window. Highlight Internet Protocol (TCP/IP) and then click [Properties].
(17) Verify that both Obtain an IP address automatically and Obtain DNS server address automatically are selected.
- 19 -
ROI-S06554
(18) In the Advanced TCP/IP Settings window, uncheck Use IP header compression for the PPP link. Click [OK].
(19) Retain the default setting on the Advanced tab and click [OK].
- 20 -
ROI-S06554
To Remove SNMP Service: (1) Select Start Setting Control Panel, then, in the Add or Remove Programs window, click Add/Remove Windows Components.
(2) The Windows Components Wizard window appears. Remove the check from Management and Monitoring Tools, and then click [Details ...].
- 21 -
ROI-S06554
(3) The Management and Monitoring Tools window appears. Confirm that Simple Network Management Protocol is not checked and click [OK]. Return to above window and click [Next].
- 22 -
ROI-S06554
To Stop SNMP Service: (1) To stop SNMP Service without removing it, click Administrative Tools in the Control Panel window.
(2)
- 23 -
ROI-S06554
(3)
Confirm that SNMP Service is installed and it has started automatically. Select Action Properties on the menu bar in the Services window, or right-click SNMP Service and then click Properties in the SNMP Service pop-up menu.
(4)
Select Manual in the Startup type field and click Stop in the Service status field on the General tab. Click [OK] or [Apply].
- 24 -
ROI-S06554
(5)
Confirm that the Status of both SNMP Service and SNMP Trap Service is stopped, and that the startup condition for each one is Manual.
(6)
- 25 -
ROI-S06554
6. PNMT Setup
NOTE If PNMT software has already been installed, please uninstall it before you install a new version.
(1) Insert the PNMT Installation CDROM.Open the CDROM folder and double-click install.exe.
- 26 -
ROI-S06554
(4) Specify the directory in which the PNMT is to be installed. Click [Next]. Restore Default Folder: Click this button to revert to default path Choose: Click this button to select another directory
NOTE The default path is C:\PNMSj. It is not possible to include blank spaces as in Program Files. (C denotes the directory where the currently running OS is installed)
- 27 -
ROI-S06554
(5) Specify the License Key file if one is available. Click [Next]. Restore Default File: Click this button to revert to default file Choose: Click this button to choose the license key file
NOTE If no license key file is available, operation in trial mode is possible. IMPORTANT: IMMEDIATE IMPORT OF LICENSE You may use the PNMT on a trial basis for 30 days. After that the PNMT can ONLY be used IF the license has been imported (activated). To obtain the license please contact NEC.
- 28 -
ROI-S06554
- 29 -
ROI-S06554
- 30 -
ROI-S06554
(2)
- 31 -
ROI-S06554
(3)
Right click the Local Area Connection and select the Properties from the context menu.
(4)
The following Local Area Connection Properties window will appear as default.
- 32 -
ROI-S06554
(5) Confirm that the Internet Protocol (TCP/IP) is only checked on the General tab, and then click on the Authentication tab.
(6)
- 33 -
ROI-S06554
(7)
Remove the check on the Enable IEEE 802.1X authentication for this network, and then click on the Advanced tab.
(8)
- 34 -
ROI-S06554
(9)
The following Windows Firewall window will appear as default. Click [OK].
(10) Return to the General tab and select the Internet Protocol (TCP/IP), then click on the [Properties].
- 35 -
ROI-S06554
(11) The following Internet Protocol (TCP/IP) Properties window will appear. Select the Use the following IP Address instead of the Obtain an IP address automatically. Set the IP address, Subnet mask and Default gateway as follows:
Item IP Address Subnet mask Default gateway Setting 172.17.254.254 255.255.255.252 172.17.254.253
- 36 -
ROI-S06554
(12) The following Advanced TCP/IP Settings window will appear. IP Settings, DNS, and WINS are not required. Select the TCP/IP filtering on the Options tab and click on [Properties].
- 37 -
ROI-S06554
(13) The following TCP/IP Filtering window will appear. Confirm that there is no check on the Enable TCP/IP Filtering (All adapters) and all the Permit All on the TCP Ports, UDP Ports and IP Protocols are selected. Click on [OK] returning to Local Area Connection Properties windows.
(14) Click on [OK] from Local Area Connection Properties window to complete the Network Connections Setting on Windows XP.
- 38 -
ROI-S06554
8. Launching PNMT
(2) If he following window appears, select [Unblock] (when using the Windows XP SP2 Firewall).
- 39 -
ROI-S06554
(3) Enter User name and Password, and Select the Connection Entry. After installation of the PNMT, the initial password will be:User name: Password: admin (There is no initial password. Just press Enter. A password can then be set.) Connection: In case of connection to 5000S select Ethernet and PNMT(LAN/Direct) entry. Otherwise select Dialup and PNMT(RS232C)/PNMT(USB) entry.
NOTE If another application is using the SNMP Port, application initialization will not be possible; the application will shut down, and the following message will appear.
- 40 -