You are on page 1of 13

TO 33D7-35-39-32

SECTION II
SPECIAL TOOLS AND TEST EQUIPMENT

2-1. SPECIAL TOOLS AND TEST EQUIPMENT equipment required to perform the work described for
FOR CHANNEL A. Table 2-1 lists special tools and test Channel B test station. Equivalent items may be used if
equipment required to perform the work described for the recommended tool/test equipment is not available
Channel A test station. Equivalent items may be used if
the recommended tool/test equipment is not available. 2-3. DRAWER ALIGNMENT PIN FABRICATION.
Four locally manufactured alignment pins are required to
2-2. SPECIAL TOOLS AND TEST EQUIPMENT perform alignment of drawers in the test station. Fabricate
FOR CHANNEL B. Table 2-2 lists special tools and test alignment pins per figure 2-1.

2-1
Table 2-1. Special Tools and Test Equipment for Channel A (CONT)
Table 2-1. Special Tools and Test Equipment for Channel A
Tool/Equipment Number Figure Number Nomenclature Use and Application
Tool/Equipment Number Figure Number Nomenclature Use and Application
Calibration of RF Interconnect Assembly and Associated Waveguide (CONT)
2142278-( ) Moving Antenna
CabinetsTest
of Mounting
Set Fixtures paragraph 5-564
M6-W-SP-12-16 Lifting Dolly Set (4940-01-046-8719) paragraph 3-9
7001309-9 Network Analyzer Case Assembly paragraph 5-565
Calibration of RF Interconnect Assembly and Associated Waveguide
2144130-2 Adapter, Waveguide to Coax paragraph 5-565
1992613-(
(QTY 2) ) Test Package, Radar Antenna 01 paragraph 5-564
(red code)
7001312-1 Adapter, TNC to 3.5mm paragraph 5-565
6458764-3 Cable Assembly, Radio Frequency 01-01 paragraph 5-564
(red code)
7001312-2 Adapter, TNC to 3.5mm paragraph 5-565
6458764-4 Cable Assembly, Radio Frequency 01-02 paragraph 5-564
5157757-2 Adapter,
(red code)3.5mm paragraph 5-565
6458086-1
7001311-1 Cable Assembly,
Electronic RadioModule
Calibration Frequency 01-03
(E-CAL) paragraph
paragraph 5-564
5-565
(red code)
6458925-1 Power Waveguide Assembly,
Supply Assembly Difference
Adjustment paragraph 5-564
01-04 (red code)
Clarostat Model 240-C Decade Box see OA/FI index,
6458763-1 Waveguide Assembly, Sum paragraph
table 5-29,5-564
01-05 (red code) paragraph 5-434,
2144130-( ) Adapter, Waveguide to Coax paragraph 5-564
paragraph 5-441
01-06 (red code)
Servo Command Signal Generator 1A1A3 Adjustment
2438176-( ) Cable Assembly, Radio Frequency 01-07 paragraph 5-564
2141740-( ) (red code)Card Assembly
Extender paragraph 5-426
6458926-2 Cable Assembly, Radio Frequency 01-08 paragraph 5-564
OA/FI
(red code)Procedures
AN/PSM-6( )
6458927-1 Multimeter
Cable Assembly, Radio Frequency 01-09 see OA/FI 5-564
paragraph index,
(red code) table 5-29
AN/TSM-131
2141740-( ) Electrical Standards
Extender Card Set (ESS)
Assembly paragraph
see OA/FI 1-4
index,
table 5-29

68D040160-( ) Circuit Card Tester Kit paragraph 5-283

Pomona 4290 SMA(M) to BNC(F) Adapter see OA/FI index,


(5935-00-321-7969) table 5-29

Tektronix 013-0084-04 BNC (M) to Probe Tip Adapter see OA/FI index,
(5935-01-499-1838) (for 3.5 mm & 5 mm) table 5-29

Avex Electronics BNC (M) to Probe Tip Adapter see OA/FI index,
599-0002 (for 7 mm) table 5-29

2-2
Table 2-1. Special Tools and Test Equipment for Channel A (CONT)

Tool/Equipment Number Figure Number Nomenclature Use and Application

OA/FI Procedures (CONT)


Paskernack PE9269 BNC(M) to BNC(F) Adapter see OA/FI index,
5935-01-534-4538 table 5-29

1993200-1 Oscilloscope Probe see OA/FI index,


part of 13A6520 table 5-29

Agilent 8120-1839 Test Cable BNC(M) to BNC(M) see OA/FI index,


(5995-01-095-6160) 24 inches table 5-29

6458121-2 Cable Assy, RF W21 (red code) see OA/FI index,


table 5-29

6458122-2 Cable Assy, RF W22 (red code) see OA/FI index,


table 5-29

6458926-2 Cable Assy, RF 01-08 (red code) see OA/FI index,


table 5-29

7001312-2 TNC(M) to 3.5mm(F), Part of see OA/FI index,


Network Analyzer Case Assembly 7001309-9 table 5-29

6458763-1 Waveguide Assy, Sum 01-05 (red code) see OA/FI index,
table 5-29

2144130-2 Waveguide to Coax Adapter, Part of Network see OA/FI index,


Analyzer Case Assembly 7001309-9 table 5-29

6458764-3 Cable Assy, RF 01-01 (red code) see OA/FI index,


table 5-29

7001312-1 Adapter TNC (F) to 3.5mm (F), Part of see OA/FI index,
Network Analyzer Case Assembly 7001309-9 table 5-29

6458086-1 Cable Assy, RF 01-03 (red code) see OA/FI index,


table 5-29

5157757-2 Adapter 3.5mm (M) to 3.5mm (M), Part of see OA/FI index,
Network Analyzer Case Assembly 7001309-9 table 5-29

6458925-1 Cable Assy, RF 01-04 (red code) see OA/FI index,


table 5-29

6458764-4 Cable Assy, RF 01-02 (red code) see OA/FI index,


table 5-29
Table 2-1. Special Tools and Test Equipment for Channel A (CONT)

Tool/Equipment Number Figure Number Nomenclature Use and Application

OA/FI Procedures (CONT)


2438176-1 Cable Assy, RF 01-07 (red code) see OA/FI index,
table 5-29

6458927-1 Cable Assy, RF 01-09 (red code) see OA/FI index,


table 5-29

5157757-1 Adapter 3.5mm (F) to 3.5mm (F), Part of see OA/FI index,
Network Analyzer Case Assembly 7001309-9 table 5-29

5157757-3 Adapter 3.5mm (M) to 3.5mm (F), Part of see OA/FI index,
Case Storage Assembly 5207457-9 table 5-29

Drawer Alignment
Locally manufactured Alignment pin Drawer alignment
(see figure 2-1) paragraph 5-501

Table 2-2. Special Tools and Test Equipment for Channel B

Tool/Equipment Figure Use and


Nomenclature
Number Number Application

Moving Cabinets or Mounting Fixtures


M6-W-SP-12-16 Lifting Dolly Set paragraph 3-9
(4940-01-046-8719)

Transmitter Mounting Fixture Relief Valve Adjustment


King Nutronics Portable Pressure Calibration/Test System paragraph 5-385
Model 3461 (Part of the ESS)

10-10 Pressure Gage Tester paragraph 5-386

Bench Stock

AN 910-2J Coupling paragraph 5-386

AN 919-10 Adapter paragraph 5-385

AN 816-7J Adapter paragraph 5-386

AN 894-6-4 Adapter, 3/8 inch-18 AMPT female to 1/4 paragraph 5-385


inch male flair fitting

7M156-4-4 Adapter, 1/4 inch-18 AMPT female to 1/4 paragraph 5-389


inch male flair fitting

2-4
Table 2-2. Special Tools and Test Equipment for Channel B (CONT)

Tool/Equipment Figure Nomenclature Use and


Number Number Application

Transmitter Mounting Fixture Cradle/Stanchion Repair


4934 (Mite Corp, NA Thread Repair Kit paragraph 5-509
Heli-Coil Products
Division, MFR Code
01556)

Calibration of Transmitter Mounting Fixture RF Assembly and Associated Waveguide Plumbing


1992614-( ) Test Package, Radar Transmitter 02 paragraph 5-570
(red code)

2132870-( ) 5-163 Elbow, Horizontal Plane Waveguide 02- paragraph 5-570


20 (red code)

2142337-( ) 5-162, 5-170 Adapter Assembly, Interlock 02-12 paragraph 5-570


(red code)

2438275-( ) 5-167 Cable Assembly, Radio Frequency 02- paragraph 5-570


14 (red code)

2439777-( ) 5-173 Cable Assembly, Radio Frequency 02- paragraph 5-570


15 (red code)

2132679-( ) 5-163 Waveguide Assembly 02-09 paragraph 5-570


(red code)

UG446A/U 5-173 Waveguide Adapter 02-17 paragraph 5-570


(red code)

Electrical Standards Set (ESS)


Hewlett Packard
A2N01N01060.0 5-156 thru 5-158, RF Cable, N termination, 5 ft (2 ea.) paragraph 3-13, 5-571
5-160 thru 5-163
5-166 thur 5-168
5-170 thru 5-173

Model X281A 5-167, 5-170, Waveguide to Coaxial Adapter (4 ea.) paragraph 5-571
5-172

Model X261A 5-160, 5-172 Waveguide to Coaxial Adapter (2 ea.) paragraph 5-571
Table 2-2. Special Tools and Test Equipment for Channel B (CONT)

Tool/Equipment Figure Nomenclature Use and


Number Number Application

Electrical Standards Set (ESS) (CONT)


Model 8491B-20 5-175 20dB Coaxial Attenuator (2 ea.) paragraph 5-596

Model 8491B-10 5-156 thru 5-158, 10dB Coaxial Attenuator (2 ea.) paragraph 5-596
5-160 thru 5-163
5-167, 5-168
5-170 thru 5-175

Model 8673D 5-157, 5-158, Synthesized Signal Generator paragraph 5-571


5-160 thru 5-163
5-167, 5-168
5-170 thru 5-175

HP 5340A 5-174 Frequency Counter paragraph 5-596

HP 436A 5-175, 5-181 Power Meter paragraph 5-596

HP 8481H 5-175 Power Sensor paragraph 5-596

HP3048A-E41 5-179 AM Noise Filter paragraph 5-596

HP 71210A-E09 5-176, 5-178 Spectrum Analyzer paragraph 5-596


(HP 71000T-E09)

HP 8780A-K21 5-180 Low Noise Test System (LNTS) paragraph 5-596

HP 8663A 5-178, 5-180 Synthesized Signal Generator paragraph 5-596


(P/O 3048A-E41)

HP 909 Opt 12 5-162, 5-172, Termination 50Ω paragraph 5-596


5-174, 5-175

HP 8491B-6 as required Attenuator 6dB paragraph 5-596

Pomona 1658-T-36 Type N(m)-Type N(m) Cable (2 paragraph 5-596


required)

HP 3048A-K21 5-178 AM Noise Filter paragraphs 5-596, 5-600


(P/O LNTS)
Table 2-2. Special Tools and Test Equipment for Channel B (CONT)

Tool/Equipment Figure Nomenclature Use and


Number Number Application

Electrical Standards Set (ESS) (CONT)


Pomona 2249- C-36 BNC Cables (6 required) paragraph 5-596

HP 8470B Crystal Detector paragraph 5-596

HP 70427A-K02 Balun Assembly paragraph 5-596


(P/O LNTS)

DORIC DS-350 Electronic Thermometer paragraph 5-409

Systron Donner
Model 5000A 5-166 Sweep Generator paragraph 5-571

Model 5015 5-166 Module 8 - 12GHz paragraph 5-571

Bench Stock
Microdot 5-182 TNC female to N female adapter paragraph 5-571
053-0248

UG29B/U 5-157, 5-158, N to N female adapter (part of ESS) paragraph 5-571


5-160 thru 5-163
5-166 thru 5-168
5-170 thru 5-173

5-166 thru 5-168 RF Cable, BNC termination, 5 feet paragraph 5-571


5-170 thru 5-173

5-165 RF Cable, N termination, 3 feet (2 ea.) paragraph 5-571

Recharging Refrigeration System


A1catel

ZM2007 N/A Vacuum Pump (part of ESS) paragraph 5-331

1010 Pressure Gage Tester paragraphs 5-415 thru 5-418

OA/FI Procedures
10-10 Pressure Gage Tester see OA/FI index, table 5-55

AN/PSM-6( ) Multimeter see OA/FI index,


tables 5-29, 5-55

AN910-2J Adapter see OA/FI index, table 5-55


Table 2-2. Special Tools and Test Equipment for Channel B (CONT)

Tool/Equipment Figure Nomenclature Use and


Number Number Application

OA/FI Procedures (CONT)


AN819-7J Adapter see OA/FI index, table 5-55

AN894-12-8 2-3 Adapter (modified) see OA/FI index, table 5-55

2132870-( ) H-plane waveguide elbow 02-20 see OA/FI index, table 5-55
(red code)

UG446A/U Waveguide Adapter 02-17 (red code) see OA/FI index, table 5-55

2142057-( ) Cable Assembly 02-01 (red code) see OA/FI index, table 5-55

2141856-( ) Cable Assembly 02-03 (red code) see OA/FI index, table 5-55

6410058-( ) Adapter Test, Interface Assembly See OA/FI index, table 5-55
02-36 (red code)

2439777-( ) Radio Frequency Cable Assembly see OA/FI index, table 5-55
02-15 (red code)

2440274-( ) Special Purpose Hose Assembly see OA/FI index, table 5-55
02-23 (red code)

Locally 2-2 72 PSI Restrictor see OA/FI index, table 5-55


manufactured
(Checkout Procedure
paragraph 5-366)

Clarostat Decade Box See OA/FI index, table 5-29


Model 240-C

68D040160-( ) Circuit Card Tester Kit paragraph 5-283

5157758-1 BNC(M) to Probe Tip Adapter see OA/FI index, table 5-29
or (for 3.5mm & 5mm)
Tektronix
013-0084-04

5157758-2 BNC(M) to Probe Tip Adapter see OA/FI index, table 5-29
or (for 7mm)
Avex Electronics
599-0002

5155412-1 BNC(M) to BNC(F) Adapter see OA/FI index, table 5-29


or
Pasternack
PE9269
Table 2-2. Special Tools and Test Equipment for Channel B (CONT)

Tool/Equipment Figure Nomenclature Use and


Number Number Application

OA/FI Procedures (CONT)


1993200-1 Oscilloscope Probe table 5-58
part of 13A6520

5157759-1 Test Cable BNC(M) to BNC(M) table 5-58


or 24 inches
Agilent
8120-1839

Drawer Alignment
Locally Alignment pin Drawer alignment
manufactured paragraph 5-501
(see figure 2-1)
TO 33D7-35-39-32

LEGEND
1. DIMENSIONS ARE IN INCHES.
2. MATERIAL: STEEL CRE BAR STOCK
A-286 (AMS 5735)
3. FINISH: PASSATIVE, MIL-STD-171

Figure 2-1. Drawer Alignment Pin Fabrication

2-9
TO 33D7-35-39-32

LEGEND
1. DIMENSIONS ARE IN INCHES.
2. MATERIAL: ALUMINUM TUBING 3/8”.

3. NORMAL RESTRICTIONS 72±5PSI.

Figure 2-2. 72 PSI Restrictor Fabrication

2-10
TO 33D7-35-39-32

Figure 2-3. AN894-12-8 Adapter Modification

2-11

You might also like