PARAMAX

PARAMAX

9000 Series

Reducer & Drive Units

9000 Series

CW21

Reducer & Drive Units

No. G2002E-7.0
Printed 2010.01

No. G2002E-7

INDEX
A

Features
Available Combination
Drive Units and Reducers
Basic Motor
Introduction of Application

Drive Unit
Standard Specications 

Construction Drawing 

Nomenclature


Selection


Service Factor SF
Selection Tables and Dimension Tables
Right Angle Shaft 

Parallel Shaft













BBBBB-







B- 11
B- 73

Reducer
Standard Specications
Construction Drawing
Nomenclature
Selection
Service Factor SF
Selection Tables and Dimension Tables
Right Angle Shaft
Parallel Shaft

2
3
4
6
8

CCCCC-

2
3
4
6
8

C- 11
C-101

Technical Data
Lubricant and Installation
Painting Specications and Rust Proof Standard
Moment of Inertia
Supplementary Dimension Drawing
Supplementary Matters to Hollow Shaft
Hollow Shaft Related Dimensions
Cooling Fan Dimension
Option Dimension
Motor Terminal Box
Motor Flange Dimension

D- 2
D- 3
D- 4
D- 12
D- 17
D- 18
D- 20
D- 24
D- 32
D- 34

A-1

Features
JUST FIT SIZE

26 sizes variation for most accurate economical selection.

Prepared full range 26 sizes variation.

Fitness size selection available for every
requested torque.
Customer's wide design availability
with most accurate economical selection.

NEW DESIGN CONCEPT

Size
9015
9025
9030
9035
9040
9045
9050
9055
9060

Output Torque
2.6
4.2
6.4
8.5
10.1
13.2
15.3
19.9
24.4

Size
9065
9070
9075
9080
9085
9090
9095
9100
9105

Output Torque
31.4
38.2
47.8
58.5
73.1
85.9
101
122
144

Size
9110
9115
9118
9121
9126
9128
9131
9136

Output Torque
174
207
260
301
351
420
473
552
M0O

Direct motor mount for right angle type also standardized.

Direct motor mount design of right angle type

is standardized.
It has a number of outstanding features.
1. No input coupling
2. No coupling alignment required
3. Compact drive assembly

LARGER THERMAL CAPACITY

Advanced thermal capacity by new designed fan cooling system. (Option)

New designed fan and conducted air cowling gain larger

thermal capacity.
This system benets for severe situation like continuous
operation, even if compact size.

Maximum

87% higher thermal rating comparison with existing design

New design fan
and hood
(PX9)

Existing design
fan and hood
(PX8)

No fans
Comparison when the thermal rating without fan is assumed to be 100%

A-2

Features
LOW NOISE

Low noise resulting from optimized gear tooth prole modication

and rigid housing design.

FEM analysis used to maximize housing strength and rigidity,

so maintaining correct gear alignment and bearing loading.

FEM Analysis

HIGH TOOTH STRENGTH

25 deg Pressure angle

In comparison with ordinary pressure angle (20 deg),

25 deg pressure angle permits a tooth form with
thicker dedendum.
This translates into higher tooth strength rating,
an essential feature for shock load applications.

25 deg Pressure Angle

UNIVERSAL HOUSING

Horizontal mounting

20 deg Pressure Angle

Horizontal, vertical or upright mounting - All use the same housing.

Vertical mounting

Upright mounting

A-3

AVAILABLE COMBINATION
Drive Unit: Right Angle
O/P speed
r/min

Motor
(kWP)

60Hz
50Hz
5.5x4
7.5x4
11x4
15x4
18.5x4
22x4
30x4
37x4
45x4
55x4

Ratio
6.3 7.1 8
9
10 11.2 12.5 14 16 18 20 22.4 25
286 254 225 200 180 161 144 129 113 100 90 80 72
238 211 188 167 150 134 120 107 94 83 75 67 60

28 31.5 35.5 40
64 57 51 45
54 48 42 38

45
40
33

50
36
30

56
32
27

63
29
24

71
25
21

28 31.5 35.5 40
64 57 51 45
54 48 42 38

45
40
33

50
36
30

56
32
27

63
29
24

71
25
21

Drive Unit: Parallel

O/P speed
r/min

Motor
(kWP)

60Hz
50Hz
5.5x4
7.5x4
11x4
15x4
18.5x4
22x4
30x4
37x4
45x4
55x4
75 x4
90 x4
110 x4

Ratio
6.3 7.1 8
9
10 11.2 12.5 14 16 18 20 22.4 25
286 254 225 200 180 161 144 129 113 100 90 80 72
238 211 188 167 150 134 120 107 94 83 75 67 60

50

56

63

71

Reducer
6.3 7.1

Size

A-4

9015
9025
9030
9035
9040
9045
9050
9055
9060
9065
9070
9075
9080
9085
9090
9095
9100
9105
9110
9115
9118
9121
9126
9128
9131
9136

10 11.2 12.5 14

16

18

Ratio
20 22.4 25

28 31.5 35.5 40

45

AVAILABLE COMBINATION

Ratio
100 112 125 140 160 180 200 224 250 280 315 355 400 450
18 16 14 13 11 10 9.0 8.0 7.2 6.4 5.7 5.1 4.5 4.0
15 13 12 11 9.4 8.3 7.5 6.7 6.0 5.4 4.8 4.2 3.8 3.3

80
23
19

90
20
17

60Hz
50Hz
5.5x4
7.5x4
11x4
15x4
18.5x4
22x4
30x4
37x4
45x4
55x4

O/P speed
r/min

Motor

(kWP)

Ratio
80 90
23 20
19 17

Reducer: Right Angle

Drive Unit: Right Angle

Reducer: Parallel
Drive Unit: Parallel

Ratio
100 112 125 140 160 180 200 224 250 280 315 355 400 450 500

80

90

9015
9025
9030
9035
9040
9045
9050
9055
9060
9065
9070
9075
9080
9085
9090
9095
9100
9105
9110
9115
9118
9121
9126
9128
9131
9136

Size

A-

AVAILABLE COMBINATION
Basic Motor

Table 1. 3-Phase Induction Motors (4 Pole).

: Standard Insulation
: Manufacutured Models
Capacity
kW

Indoor
Type

5.5
7.5
11
15
18.5
22
30
37
45
55

Remarks

Outdoor CorrosionType proof Class 2

Specications
Insulation Class
F

Inverter Motors (Constant Torque)

Indoor Type Outdoor Type

Continuous Rating, 55kW and under,

Applicable Voltage : 200V 50/60Hz(400V 50/60Hz,440V 60Hz,440V 60Hz)
Provided that the base frequency for driving an inverter is 60 Hz.

Table 2. 3-Phase Induction Motors with Built-in Brakes (4 Pole).

: Standard Insulation
: Manufacutured Models
Capacity
kW

Indoor
Type

5.5
7.5
11
15
18.5
22
30
37

Remarks

Outdoor CorrosionType proof Class 2

Specications
Insulation Class
F

Inverter Motors (Constant Torque)

Indoor Type Outdoor Type

Continuous Rating,
Applicable Voltage : 200V 50/60Hz , 220V 50/60Hz (400V 50/60Hz , 440V 60Hz)
Provided that the base frequency for driving an inverter is 60 Hz.
Brake Insulation : B type

Notes: 1. Motors with output kW specications other than as listed in Tables 1-4 are also manufactured.
Consult factory.
Examples: Special voltage, dust-proof, humidity-proof, tropical treatment, high temperature,
ship use, dual shaft (round & square shaft), CSA standard, NEMA standard, etc.
2. When using an inverter drive, advice us of ambient temperature, input r/min, mounting method,
load characteristics and other conditions of use.

A-6

AVAILABLE COMBINATION

Table 3. Safety Increased Explosion-proof (eG3) 3-Phase Induction Motor (4 Pole).

: Standard Insulation
: Manufacutured Models
Capacity
kW
5.5
7.5
11
15
18.5
22
30
37
45
55
Remarks

Indoor
Type

Outdoor
Type

Specications
Insulation Class
Corrosionproof Class 2
B
F

Continuous Rating
Applicable Voltage: 200V, 220V, 350V, 380V, 400V, 440V, 50/60Hz

Table 4. Pressure-tight Explosion-proof (d2G4) 3-Phase Motor (4 Pole).

: Standard Insulation
: Manufacutured Models
Capacity
kW
5.5
7.5
11
15
18.5
22
30
37

Remarks

Indoor
Type

Outdoor
Type

Specications
Corrosion- Insulation Class
proof Class 2
B

Inverter Motors (Constant Torque)

Indoor Type

Continuous Rating
Applicable Voltage : 200V , 220V , 350V , 380V , 400V , 440V 50/60Hz
(Inverter Motors) : 200V 60Hz , 220V 60Hz , 400V 60Hz , 440V 60Hz
Applicable Inverter :Applicable only to Sumitomo Inverters.(Refer to Inverter
catalogue.)

A-7

INTRODUCTION OF APPLICATION
With Motor

Common base
Double Stack

Single stage

Drive unit right angle

Drive unit parallel

Reducer
Top mount
Steel housing

Right angle

Mounting
Parallel
Special slow speed shaft

Upright wall mount

Upright mount

Vertical mount

A-8

Drop bearing housing

Ceiling mount

Hollow shaft

B
<Drive Unit Right Angle Shaft>

<Drive Unit Parallel Shaft>

Drive Unit
Standard Specications 
Construction Drawing 
Nomenclature 

Selection

Service Factor SF

Right Angle Shaft
Parallel Shaft 

Exact Reduction Ratio

B- 2
B- 3
B- 4

B- 6
 B- 8
B- 11
 B- 73
 B- 110

B-1

Drive Unit Standard Specifications

Item

Standard Specification

Standard Specification with Built-in Brake

Capacity
Range

5.5kW x 4P 55kW x 4P

5.5kW x 4P 37kW x 4P

Enclosure

Totally enclosed fan cooled type

Totally enclosed fan cooled type

200V 50/60Hz, 220V 60Hz

380~415V 50Hz, 440~460V 60Hz
For other voltages contact Sumitomo.

Motor

Power
Source
Insulation

Class F

Class F

Time
Rating

Continuous rating

Continuous rating

Lead wiring
Lead
Wiring
(Lug
Type)

Lead wiring

5.5 7.5kW
(Direct starting)

11 55kW
( -starting available)

6
Drive Unit

4P

4P

5.5 7.5kW
(Direct starting)

11kW
( -starting available)

10

15 37kW
( -starting available)

Standards Conforms to JIS, CE or UL. Consult Sumitomo for delaits.

Dimension Selection
Tables
Tables

Standard Specification
Item

Reducer

Lubrication
Method

Mounting

High Speed Shaft

Speed

Horizontal Shaft

750 1800r/min

Oil bath lubrication

In case of high speed shaft speed is less than 750r/min, electric
pump lubrication may be used. Consult Sumitomo for details.

Vertical Shaft

400 1800r/min

Pump lubrication
(Two different pump lubrication systems are available; shaft
connected pump lubrication and electric pump lubrication. For
details, refer to the outline dimension drawing.)

Upright Shaft

750 1800r/min

Oil bath lubrication

Grease lubrication for right angle input shaft.

Lubricant Refer to the page D-2

Ambient Conditions

Gear
Type

Involute external gear

Installation
Indoor (Minimal dust and humidity)
Location
-1040
Ambient
Temperature A cooling fan may be required depending on the usage (Note)
Ambient
Humidity

Under 85%

Elevation

Less than 1,000 meters above sea level

Atmosphere Well ventilated location, free of corrosive and explosive gases, vapor, and dust.

Installation

Horizontal installation
Refer to the page D-2

Method of
Coupling with Coupling, gears, chain sprocket or belt.
Driven Machine

Painting

Surface preparation: Shot blast after wash before machining

Inside paint: UNI GROUND PTC primer is sprayed once
Outside paint: For primer coating, UNI GROUND PTC primer is sprayed once.

For final coating, NEORON #2000 is sprayed once.
Paint color: Donau Blue (equivalent Munsell color: 6.5PB 3.6/8.2), Refer to page D-3.

Note : In general, a heating or cooling system is necessary when ambient temperature is lower than -10 or
higher than 50.
e.g. High temperature gas or liquid passes through the hollow shaft.
Consult us when substances lower than 10 or higher than 50 will be in contact with PARAMAX
DRIVES.

B-

Drive Unit Construction Drawing

19

18

17

16

15

14

13

12

10

11

11

Drive Unit Right Angle Shaft Triple Reduction

9
23

20

22

21

Drive Unit Parallel Shaft Triple Reduction

Ref.No.

Part Name

Ref.No.

Part Name

Ref.No.

Part Name

Ref.No.

Part Name

Housing

Taper roller bearing

13

Taper roller bearing

19

Taper roller bearing

Helical gear

Bearing housing

14

Helical pinion shaft

20

Helical gear

Slow speed shaft

Flange for motor

15

Helical pinion shaft

21

Helical pinion shaft

Taper roller bearing

10

Oil seal

16

Helical gear

22

Motor adapter

Bevel gear

11

Motor

17

Collar

23

Coupling

Taper roller bearing

12

Bevel pinion shaft

18

Oil seal

B-3

Drive Unit Nomenclature

Series

Mounting

Housing

Drive Unit

9055

Size

Torque
kNm

9015

2.6

9025

4.2

9030

6.4

9035

8.5

9040

10.1

Shaft Position

3
Number of Gear
Stage

Horizontal

Dimension Selection
Tables
Tables

A
Monoblock

Double Reduction

Right Angle

3
9045

13.2

9050

15.3

9055

19.9

9060

24.4

9065

31.4

9070

38.2

9075

47.8

9080

58.5

9085

73.1

P
Paramax

Vertical

W
D
Split

B-4

Parallel

Quadruple
Reduction

Upright

1. For shaft arrangement, refer to the dimension sheets.

2. Consult us for reduction ratios smaller than 6.3.

Triple Reduction

Drive Unit Nomenclature

R
Mounting for
Upright

Shaft
Arrangement

High Speed Shaft

Slow Speed
Shaft

(Blank)

(Blank)

Option

Nominal
Ratio

(Blank)

Right Angle Shaft

RL

Right Angle Shaft

RR

Solid Shaft
RB

Without Option
LR
LL

LB

Parallel Shaft

B
Hollow Shaft
(Shrink Disk Type)

RL

Flange for Motor

(Right Angle Shaft)

RR

With Backstop

Hollow Shaft
(Key Type)

Wall Mount
(Upright
Mounting)
Motor Adapter
(Parallel Shaft)

35.5

6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4
25
28
31.5
35.5
40
45
50

56
63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450

Parallel Shaft
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4
25
28
31.5
35.5
40
45
50

56
63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

B-5

Drive Unit Selection

Ambient condition

Standard Specifications Page B-2

Determine Drive Unit

Calculate motor power

Dimension Selection
Tables
Tables

Determine Nomenclature

Drive Unit

Select output speed and ratio

No

Determine the service factor

SF (Service Factor): Page B-8

Determine shaft
and mounting positions

Nomenclature Page B-4 ~ B-5

Determine drive unit

Selection tables
Right angle shaft: Page B-16 ~ B-37
Parallel shaft: Page B-78 ~ B-97

Determine Nomenclature

Page number of relevant Dimension Table is

indicated in the Selection Table.
Select shaft arrangement from "Standard
Shaft Arrangement Configuration" in the
Dimension Tables.

Is overhung load
applied to the slow speed
shaft?

Calculate equivalent radial load FrE and equivalent

thrust load FxE at peak load.
Cf : Overhung factor
FrE : Equivalent radial load = Peak radial load Fr Cf
FxE : Equivalent axial load = Peak thrust load Fx Cf
FrA : Allowable radial load
FxA : Allowable axial load

Yes

Is overhung load
radial load only?

No

Refer to the following pages for Cf, FrA, and Fx A

values.
Right angle shaft: Page B-38 ~ B-41
Parallel shaft: Page B-98 ~ B-101

Check Overhung Load

Yes
Calculate equivalent
radial load FrE

Calculate equivalent radial load FrE

and calculate equivalent thrust load FxE

Check overhung load

FrE

No

FrA
Yes

Yes

Check overhung load

FrE
FrA

FxE
FxA

No
Complete selection

B-6

Consult us for large

overhung load.

Drive Unit Selection Example

Reference page No.

Conditions Selected item

Ambient condition
Check ambient condition

 Indoor, Ambient temperature 20

OK

Load Power P
Motor power

: P = 17kW
18.5 kW

Electric source
Output speed

: 200V 50Hz
: 33 r/min

Load condition
Type of load, Operating hours
Determine service factor

: Uniform load 14 hours/day

SF=1.25

B-2 Standard Specifications

Service Factor

B-8

: Right Angle ShaftHorizontal Mounting B-4 B-5

Shaft and mounting positions
Determine size, shaft position, number of stages 9030 R3 45
B-24
Size 9030
Right Angle Shaft Triple Reduction

Nominal Reduction Ratio 45

Check dimension
Check shaft arrangement
Check nomenclature

RML
PHA9030R3-RML-45

Check overhung load

Overhung member
Overhung factor Cf
Radial load position and direction
Peak radial load Fr
Peak thrust load Fx
Equivalent radial load FrE
Allowable radial load

: Sprocket (Single row)

Cf = 1.0
: Center of solid shaft, Downward
: 10.6 kN
: 0 kN
FrE = 10.6 1.0 = 10.6
26.5 kN

10.6 26.5
Motor specification
Check motor specification
Complete Selection
Selected model

B-44 *1

Nomenclature
Selection Tables

Dimension Tables

B-38

Allowable external load

B-38

Allowable Radial Load

A-6

Available Combination
of Basic Motor

OK
: 200V 50Hz without brakeindoor
OK

PHA9035R3-RML-45
200V 50Hz without brakeindoor

*1 Page number of the

relevant Dimension

Table is indicated in the

Selection Table.

B-7

Drive Unit Service Factor SF

Service Factor SF
Driven Machine

Operating Hours (hours/day)

3 hrs

10 hrs

Group

Travel Slewing Boom The crane

Hoisting Traverse
Motion Motion Motion Hoisting classication is
1.00
1.50
1.25
1.00 based on JIS
1.25
1.50
1.00 B8821-1976
"Calculation standard
1.50
1.75
1.25 for the structure of
2.00
1.50 crane."
1.75

CONVEYORS (General purpose)

Uniformly load or fed
Heavy load
Not uniformly fed
Reciprocating or shaker

1.00
1.00
1.50

1.00
1.25
1.75

1.25
1.50
2.00

Elevators
Escalators

Dimension Selection
Tables
Tables

Draw bench carriage and main drive

Runout table
Non reversing
Group drives
Individual drivers
Reversing
Slab pushers
Shears
Wire drawing
Wire winding machine

24 hrs

1.75
1.50
1.50

1.75
1.50
1.50

2.00
1.75
1.50

1.75
2.00

1.75
2.00

1.75
2.00

1.25
1.50
1.50

1.25
1.50
1.50

1.25
1.50
1.50

2.00

2.00

2.00

1.00
1.00
1.00

1.00
1.25
1.25

1.25
1.50
1.50

1.25

1.25

1.50

2.50

2.50

2.50

1.00
1.00
1.00

1.00
1.25
1.25

1.25
1.50
1.50

Bridles
Coilers & uncoilers
Edge trimmers
Flatteners
Loopers (Accumulators)
Pinch rolls
Scrap choppers
Shears
Slitters

1.00
1.00
1.50
1.75

1.00
1.25
1.50
1.75

1.25
1.50
1.75
2.00

1.00

1.25
1.50
1.50

1.00

1.25
1.50
1.50

1.25

1.25
1.50
1.50

1.00
1.25
1.25

1.00
1.25
1.25

1.25
1.50
1.50

1.25
1.25
2.00
2.00
1.75
1.25
1.25

1.25
1.25
2.00
2.00
1.75
1.25
1.25

1.50
1.50
2.00
2.00
2.00
1.50
1.50

GENERATORS AND EXCITERS

1.00

1.00

1.25

HAMMER MILLS

1.75

1.75

2.00

2.00
1.50
1.50
1.75

2.00
1.50
1.50
1.75

2.00
1.50
1.50
1.75

AGITATORS AND MIXERS

1.50

1.50

1.50

Pure liquids
Liquids and solids
Liquids variable density

1.50
2.00
2.00
1.50
2.00
1.25
1.25

1.50
2.00
2.00
1.50
2.00
1.25
1.50

1.50
2.00
2.00
1.50
2.00
1.25
1.50

1.50
1.00
1.00
1.25
1.50
1.25
2.00
2.00
1.00

1.50
1.25
1.25
1.25
1.50
1.25
2.00
2.00
1.25

1.50
1.50
1.50
1.50
2.00
1.50
2.00
2.00
1.50

2.00
2.00
1.50
1.50

2.00
2.00
1.50
1.50

2.00
2.00
1.50
1.50

2.00
1.25
1.25
1.50
1.50
1.50
1.25
1.50
1.50

2.00
1.25
1.25
1.50
1.50
1.50
1.25
1.50
1.50

2.00
1.25
1.25
1.50
1.50
1.50
1.25
1.50
1.50

MIXERS

1.25
1.50

1.25
1.50

1.25
1.50

1.00
1.00
1.00
1.50
1.00

1.25
1.25
1.00
1.75
1.25

1.50
1.50
1.25
2.00
1.50

FEEDERS
Apron
Belt
Disk
Reciprocating
Screw

CRUSHER
Stone or ore

BLOWERS
Centrifugal
Lobe
Vane
Centrifugal
Lobe
Reciprocating: multi cylinder
Reciprocating: single cylinder

FANS
Centrifugal
Cooling towers
Forced draft
Suction draft
Industrial and mine

PUMPS
Centrifugal
Screw pump
Gear pump

DREDGES

EXTRUDERS
Plastics
Rubber

Concrete

COMPRESSORS

SEWAGE DISPOSAL EQUIPMENT

Aerators
Bar screens
Chemical feeders
Dewatering screens
Scum breakers
Slow or rapid mixers
Sludge collectors
Thickeners
Vacuum filters

All types incl. Paper making machine

1.50
1.25

MILL, ROTARY TYPE

Ball and rod
Cement Kilns
Kilns (Except cement kilns)
Dryers and coolers

Mixers
Mixing mill -2 smooth rolls
Batch drop mill -2 smooth rolls
Cracker warmer
-2 roll: 1 corrugated roll
Cracker -2 corrugated rolls
Holding, feed and blend mill
-2 rolls
Rener -2 rolls
Calenders

1.50
1.25

METAL STRIP PROCESSING MACHINERY

B-8

10 hrs

1.50
1.25

METAL MILLS

3 hrs

PAPER MILL

ELEVATORS

Drive Unit

Operating Hours (hours/day)

RUBBER INDUSTRY

CRANES
Classication of
Crane
Group
Group
Group

Driven Machine

24 hrs

Cable reels
Conveyors
Cutter head drive
Pumps
Screen drives
Stackers
Winches

SUGAR INDUSTRY
Beet slicer
Cane knives
Crushers
Mills (Slow speed end)

Notes:
(1) Values in the above table are based on AGMA standards and SUMITOMO's
experience.
(2) Values in the above table apply for electric motors as prime movers - if prime
mover is a multi cylinder combustion engine, 0.25 has to be added to the SF.
(3) Consult us for special duty or when special safety specifications are needed.
(4) : For SF, consult us.

Drive Unit Service Factor SF

Refer to the following for driven machines not shown on the left page.
Type of Load
Prime Mover

Operating
Hours

Uniform Load

Moderate
Shock Load

Heavy Shock
Load

Electric Motor

3 hours/day
10 hours/day
24 hours/day

1.00
1.00
1.25

1.00
1.25
1.50

1.50
1.75
2.00

Internal Combustion
Engine
(multi cylinder)

3 hours/day
10 hours/day
24 hours/day

1.00
1.25
1.50

1.25
1.50
1.75

1.75
2.00
2.25

Note: Consult us when the operating hours are less than 3 hours/day or when an internal combustion
engine (single cylinder) is used.

B-9

B - 10

<Drive Unit Right Angle Shaft Horizontal Mounting>

<Drive Unit Right Angle Shaft Upright Mounting>

<Drive Unit Right Angle Shaft Vertical Mounting>

Drive Unit Right Angle Shaft

B- 12
Allowable Radial
B- 38
and Thrust Loads
Dimension Sheets
B- 42
Exact Actual Ratio
B- 110
Selection

B - 11

SELECTION Drive Unit Right Angle Shaft

Shaft Position

Combinations with 4P motor

High Speed Shaft Speed Ambient Temperature

Right Angle Shaft

1500r/min

40 Degree
Low Speed Shaft Speedr/min

kW

SF

238

Dimension Selection
Tables
Tables

188

167

150

134

120

107

94

83

75

67

60

54

25

28

48

42

38

33

30

40

45

50

Nominal Reduction Ratio

6.3

Drive Unit

211

7.1

10

11.2 12.5

14

16

18

20

22.4

31.5 35.5

9030 9030 9030 9030 9030

5.5kW

1.25

9030 9030 9030 9030 9030

4P

1.5

9030 9030 9030 9030 9030

9030 9030 9030 9030 9030

9030 9030 9030 9030 9030 9030

7.5kW

1.25

9030 9030 9030 9030 9030 9030

4P

1.5

9030 9030 9030 9030 9030 9030

9030 9030 9030 9030 9030 9030

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030

11kW

1.25

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030

4P

1.5

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9035

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9035

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030

15kW

1.25

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9035

4P

1.5
2
1

Size of Reducer

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9035
9030 9030 9030 9030 9030 9030 9030 9030 9035 9035 9040 9040 9045
9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035

18.5kW

1.25

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035

4P

1.5

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9040 9040 9045

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9040 9045 9045

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035

22kW

1.25

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9040 9040 9045

4P

1.5

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9040 9040 9045

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9040 9045 9045 9045 9050

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045

30kW

1.25

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045

4P

1.5

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9050

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9050 9055 9055

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045

37kW

1.25

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9035 9040 9040 9045 9045 9050 9050

4P

1.5

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9045 9050 9055 9055

9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9055 9055 9060 9060

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9045 9050 9050

45kW

1.25

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9045 9050 9055 9055

4P

1.5

9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9040 9040 9045 9045 9045 9055 9055 9055 9060

9040 9040 9040 9040 9040 9040 9045 9045

9050 9050 9050 9055 9055 9060 9060 9065 9065

9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9045 9055 9055 9055 9055 9055 9055 9055

55kW

1.25

9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9050 9055 9055 9055 9055 9055 9060 9060

4P

1.5

9040 9040 9040 9040 9040 9040 9045 9045

9050 9050 9055 9055 9055 9055 9060 9065 9065

9040 9040 9040 9040 9040 9040 9045 9045

9070 9070 9070 9070 9070 9070 9070 9070 9075

B - 12

SELECTION Drive Unit Right Angle Shaft

Combinations with 4P motor

Low Speed Shaft Speedr/min

27

24

21

19

17

15

13

12

11

9.4

8.3

7.5

6.7

6.0

5.4

4.8

4.2

3.8

3.3

224

250

280

315

355

400

450

SF

kW

Nominal Reduction Ratio

56

63

71

80

90

100

112

125

140

160

180

200

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9050 9055 9055

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9055 9055 9055

1.25

5.5kW

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9055 9055 9055 9065 9065

1.5

4P

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9055 9055 9060 9060 9065 9065 9075

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9055 9055 9065

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9055 9055 9060 9065 9065

1.25

7.5kW

9030 9030 9030 9035 9035 9040 9040 9040 9045 9045 9045 9050 9055 9055 9060 9060 9065 9065 9075

1.5

4P

9030 9030 9035 9035 9035 9040 9045 9045 9050 9055 9055 9060 9060 9060 9065 9065 9070 9075 9075

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9055 9055 9060 9060 9065 9065 9075

9030 9030 9030 9035 9035 9040 9040 9045 9045 9045 9055 9055 9055 9060 9065 9065 9070 9075 9075

1.25

11kW

9035 9040 9040 9040 9040 9040 9045 9045 9055 9055 9055 9060 9065 9065 9065 9065 9070 9075 9075

1.5

4P

9035 9040 9045 9045 9045 9050 9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9075 9085 9085

9030 9030 9035 9035 9035 9040 9045 9045 9050 9055 9055 9060 9060 9060 9065 9065 9070 9075 9075

9035 9040 9040 9045 9045 9045 9050 9050 9055 9055 9060 9060 9065 9065 9070 9075 9075 9075 9085

1.25

15kW

9035 9040 9045 9045 9045 9050 9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9075 9085 9085

1.5

4P

9045 9050 9050 9055 9055 9060 9060 9060 9065 9065 9070 9070 9075 9075 9080 9085 9085 9085

9035 9040 9040 9040 9045 9045 9050 9050 9055 9055 9060 9060 9065 9065 9070 9070 9075 9075 9075

9035 9040 9045 9045 9050 9050 9055 9055 9065 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

1.25

18.5kW

9045 9050 9050 9055 9055 9060 9060 9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

1.5

4P

9050 9050 9055 9055 9060 9060 9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

9035 9040 9045 9045 9045 9050 9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9075 9085 9085

9045 9050 9050 9055 9055 9060 9060 9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

1.25

22kW

9045 9050 9055 9055 9055 9060 9065 9065 9065 9065 9070 9070 9075 9075 9085 9085 9085

1.5

4P

9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9075 9080 9085 9085 9085
9045 9050 9050 9055 9055 9060 9060 9060 9065 9065 9070 9070 9075 9075 9080 9085 9085 9085

2
1

9050 9050 9055 9055 9065 9070 9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

1.25

30kW

9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9080 9085 9085 9085

1.5

4P

9060 9060 9065 9065 9070 9070 9075 9075 9080 9085 9085

9050 9050 9055 9055 9060 9060 9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9080 9085 9085

1.25

37kW

9060 9060 9065 9065 9070 9070 9075 9075 9075 9080 9085 9085

1.5

4P

9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9080 9085 9085 9085

9060 9060 9065 9065 9070 9070 9075 9075 9075 9080 9085 9085

1.25

45kW

9065 9065 9070 9075 9075 9080 9080 9080 9085 9085 9085

1.5

4P

9070 9075 9075 9080 9080 9080 9085 9085

9060 9060 9065 9065 9070 9070 9075 9075 9075 9080 9085 9085

9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

1.25

55kW

9065 9070 9070 9075 9075 9080 9080 9085 9085

1.5

4P

9075

B - 13

SELECTION Drive Unit Right Angle Shaft

Shaft Position

Combinations with 4P motor

High Speed Shaft Speed Ambient Temperature

Right Angle Shaft

1800r/min

40 Degree
Low Speed Shaft Speedr/min

kW

SF

286

Dimension Selection
Tables
Tables

225

200

180

161

144

129

113

100

90

80

72

64

25

28

57

51

45

40

40

45

36

Nominal Reduction Ratio

6.3

Drive Unit

254

7.1

10

11.2 12.5

14

16

18

20

22.4

31.5 35.5

50

9030

5.5kW

1.25

9030

4P

1.5

9030

9030

9030 9030 9030 9030 9030

7.5kW

1.25

9030 9030 9030 9030 9030

4P

1.5

9030 9030 9030 9030 9030

9030 9030 9030 9030 9030

9030 9030 9035 9030 9030 9030 9030 9030 9030 9030 9030

11kW

1.25

9030 9030 9035 9030 9030 9030 9030 9030 9030 9030 9030

4P

1.5

9030 9030 9035 9030 9030 9030 9030 9030 9030 9030 9030

9030 9030 9035 9035 9030 9030 9030 9030 9030 9030 9035

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030

15kW

1.25

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030

4P

1.5

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9035

9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9030 9035 9035

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035

18.5kW

1.25

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035

4P

1.5

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035

2
1

Size of Reducer

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9040 9040 9045

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035

22kW

1.25

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035

4P

1.5

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9040 9040 9045

9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9035 9040 9045 9045

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040

30kW

1.25

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045

4P

1.5

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9050 9055

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045

37kW

1.25

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045

4P

1.5

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9050

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9055 9055 9055

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9045 9045 9045

45kW

1.25

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9045 9050 9050

4P

1.5

9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9045 9050 9055 9055

9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9055 9055 9060 9065

9040 9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9045 9055 9055 9055 9055 9055 9055 9055

55kW

1.25

9040 9040 9040 9040 9040 9040 9040 9040 9040 6045 6045 6045 9055 9055 9055 9055 9055 9055 9055

4P

1.5
2

B - 14

9040 9040 9040 9040 9040 9040 9040 9040 9045 9045 9050 9050 9055 9055 9055 9055 9055 9060 9060
9040 9040 9040 9040 9040 9040 9045 9045

9060 9060 9060 9060 9065 9065 9070 9070 9070

SELECTION Drive Unit Right Angle Shaft

Combinations with 4P motor

Low Speed Shaft Speedr/min

32

29

25

23

20

18

16

14

13

11

10

9.0

8.0

7.2

6.4

5.7

5.1

4.5

4.0

224

250

280

315

355

400

450

SF

kW

Nominal Reduction Ratio

56

63

71

80

90

100

112

125

140

160

180

200

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9050 9055 9055

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9050 9055 9055

1.25

5.5kW

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9055 9055 9055

1.5

4P

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9055 9050 9055 9055 9060 9065 9065

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9050 9050 9055 9055

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9050 9055 9055 9055 9065

1.25

7.5kW

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9055 9055 9060 9065 9065

1.5

4P

9030 9030 9030 9035 9035 9040 9040 9040 9045 9045 9050 9050 9055 9055 9060 9065 9065 9075 9075

9030 9030 9030 9035 9035 9040 9040 9040 9040 9045 9045 9050 9050 9050 9055 9055 9060 9065 9065

9030 9030 9030 9035 9035 9040 9040 9040 9045 9045 9045 9050 9055 9055 9060 9060 9065 9065 9075

1.25

11kW

9030 9030 9030 9035 9035 9040 9040 9045 9045 9045 9055 9055 9055 9060 9065 9065 9070 9075 9075

1.5

4P

9035 9040 9040 9040 9045 9045 9045 9050 9055 9055 9060 9060 9065 9065 9070 9070 9075 9075 9075

9030 9030 9030 9035 9035 9040 9040 9040 9045 9045 9050 9050 9055 9055 9060 9065 9065 9075 9075

9030 9030 9035 9035 9035 9040 9045 9045 9050 9055 9055 9060 9060 9060 9065 9065 9070 9075 9075

1.25

15kW

9035 9040 9040 9040 9045 9045 9050 9050 9055 9055 9060 9060 9065 9065 9070 9070 9075 9075 9085

1.5

4P

9040 9040 9045 9045 9050 9055 9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

9035 9035 9035 9035 9035 9040 9045 9045 9050 9055 9055 9060 9060 9060 9065 9065 9070 9075 9075

9035 9040 9040 9040 9045 9045 9050 9050 9055 9055 9060 9060 9065 9065 9070 9075 9075 9075 9085

1.25

18.5kW

9035 9040 9045 9045 9050 9050 9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

1.5

4P

9045 9050 9050 9055 9055 9060 9060 9060 9065 9065 9070 9070 9075 9075 9080 9085 9085

9035 9040 9040 9040 9045 9045 9045 9050 9055 9055 9060 9060 9065 9065 9070 9070 9075 9075 9075

9035 9040 9045 9045 9045 9050 9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

1.25

22kW

9045 9050 9050 9055 9055 9060 9060 9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

1.5

4P

9050 9050 9055 9055 9060 9060 9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

9040 9040 9045 9045 9050 9055 9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

9045 9050 9050 9055 9055 9060 9060 9060 9065 9065 9070 9070 9075 9075 9080 9085 9085

1.25

30kW

9050 9050 9055 9055 9060 9060 9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

1.5

4P

9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085 9085

9045 9050 9050 9055 9055 9060 9060 9060 9065 9065 9070 9070 9075 9075 9080 9085 9085

9050 9050 9055 9055 9065 9070 9070 9070 9070 9075 9075 9080 9080 9085 9085 9085

1.25

37kW

9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9080 9085 9085

1.5

4P

9060 9065 9065 9070 9070 9070 9075 9075 9080 9085 9085

9050 9055 9055 9055 9060 9060 9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9080 9085 9085

1.25

45kW

9060 9060 9065 9065 9070 9070 9075 9075 9075 9080 9085 9085

1.5

4P

9065 9070 9070 9075 9075 9080 9080 9080 9085 9085

9055 9055 9060 9065 9065 9070 9070 9070 9075 9075 9080 9080 9085 9085

9060 9065 9065 9070 9070 9070 9075 9075 9075 9085 9085

1.25

55kW

9065 9065 9070 9075 9075 9080 9080 9080 9085 9085

1.5

4P

9070 9075 9075 9080 9080 9080 9085 9085

B - 15

SELECTION Drive Unit Right Angle Shaft

5.5kW

Frequency Hz
Pole
P
5RGGFn1 r/min

50Hz
4
1500

60Hz
4
1800

Frequency
Output Speed
r/min

Drive Unit

Dimension Selection
Tables
Tables

B - 16

50Hz
Output Torque (Tout)
Nm
kgf m

47.6
42.3

1100
1240

113
127

37.5

1400

143

33.3

1580

161

30.0

1750

179

26.8

1960

200

23.8

2210

225

21.1

2490

254

18.8

2800

286

16.7

3150

322

15.0

3500

358

13.4

3920

400

12.0

4380

447

10.7

4900

501

9.4

5600

572

8.3

6300

644

7.5

7000

715

6.7

7840

801

6.0

8750

894

5.4

9800

1000

4.8

11030

1130

4.2

12430

1270

SF
4.89
4.89
4.69
4.89
4.21
4.89
2.92
4.89
4.74
2.92
4.47
4.74
2.92
4.74
2.69
2.92
3.98
4.74
2.92
3.89
4.74
2.85
3.18
4.18
4.60
3.05
3.94
4.52
2.50
3.34
3.70
4.60
2.47
3.09
3.61
4.60
2.03
2.63
2.98
3.89
4.65
2.50
2.60
3.87
2.12
2.43
3.10
3.80
4.85
2.27
2.60
3.69
3.89
1.87
2.54
2.90
3.89
1.81
2.43
2.96
3.85
4.69
1.94
2.34
3.03
3.90
1.40
1.94
2.09
3.09
3.40
4.94
1.20
1.56
1.89
2.43
3.20
4.14
4.70

Output Speed
r/min

5.5kW

60Hz
Output Torque (Tout)
Nm
kgf m

57.1
50.7

919
1040

94
106

45.0

1170

119

40.0

1310

134

36.0

1460

149

32.1

1630

167

28.6

1840

188

25.4

2070

212

22.5

2330

238

20.0

2630

268

18.0

2920

298

16.1

3270

334

14.4

3650

372

12.9

4090

417

11.3

4670

477

10.0

5250

536

9.0

5840

596

8.0

6540

667

7.2

7300

745

6.4

8170

834

5.7

9190

938

5.1

10360

1060

Model
SF

Size

5.81
5.81
5.45
5.81
5.05
5.81
3.50
5.81
5.69
3.50
5.34
5.69
3.50
5.69
3.21
3.50
4.76
5.69
3.50
4.65
5.69
3.41
3.81
5.00
5.45
3.65
4.72
5.41
3.00
4.00
4.45
5.45
2.96
3.70
4.34
5.45
2.43
3.14
3.56
4.65
5.45
3.00
3.10
4.63
2.54
2.92
3.72
4.56
5.81
2.72
3.10
4.41
4.67
2.23
3.05
3.49
4.67
2.18
2.90
3.56
4.63
5.45
2.34
2.80
3.63
4.67
1.67
2.32
2.50
3.70
4.09
5.81
1.45
1.87
2.27
2.92
3.83
4.96
5.63

9030
9030
9030
9035
9030
9035
9030
9035
9040
9030
9035
9040
9030
9040
9030
9035
9040
9045
9035
9040
9045
9035
9040
9045
9050
9040
9045
9050
9040
9045
9050
9055
9040
9045
9050
9055
9040
9045
9050
9955
9060
9045
9050
9055
9045
9050
9055
9060
9065
9050
9055
9060
9065
9050
9055
9060
9065
9050
9055
9060
9065
9070
9055
9060
9065
9070
9050
9055
9060
9065
9070
9075
9050
9055
9060
9065
9070
9075
9080

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R4
R3
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

31.5
35.5
40
40
45
45
50
50
50
56
56
56
63
63
71
71
71
71
80
80
80
90
90
90
90
100
100
100
112
112
112
112
125
125
125
125
140
140
140
140
140
160
160
160
180
180
180
180
180
200
200
200
200
224
224
224
224
250
250
250
250
250
280
280
280
280
315
315
315
315
315
315
355
355
355
355
355
355
355

B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-48
B-48
B-44
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-48
B-50
B-48
B-48
B-48
B-48
B-48
B-48
B-50
B-50
B-48
B-48
B-50
B-50
B-48
B-48
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-58
B-58
B-54
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-58
B-60
B-58
B-58
B-58
B-58
B-58
B-58
B-60
B-60
B-58
B-58
B-60
B-60
B-58
B-58
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60

B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-68
B-68
B-64
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-68
B-70
B-68
B-68
B-68
B-68
B-68
B-68
B-70
B-70
B-68
B-68
B-70
B-70
B-68
B-68
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

3.8

14010

1430

3.3

15760

1610

7.5kW

SF
1.47
2.18
3.61
1.25
1.96
3.38
4.92

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

4.5

11670

1190

4.0

13130

1340

50Hz
4
1500

Model
SF

Size

1.76
2.61
4.32
1.50
2.36
4.07
5.81

9055
9065
9075
9055
9065
9075
9085

Output Speed
r/min
53.6
47.6
42.3

1340
1500
1700

137
154
173

37.5

1910

195

33.3

2150

219

30.0

2390

244

26.8

2670

273

23.8

3010

307

21.1

3390

346

18.8

3820

390

16.7

4300

439

15.0

4780

488

13.4

5350

546

12.0

5970

609

SF
4.93
3.58
3.58
3.44
3.58
3.09
3.58
4.57
2.14
3.58
3.48
2.14
3.28
3.48
4.80
2.14
3.48
1.97
2.14
2.92
3.48
4.26
2.14
2.85
3.48
4.93
2.09
2.33
3.06
3.37
4.53
4.93
2.24
2.89
3.32
4.93
1.84
2.45
2.72
3.37
4.13
1.81
2.26
2.65
3.37
4.26

Output Speed
r/min

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R4
R4
R4
R4
R4
R4
R4

400
400
400
450
450
450
450

B-48
B-50
B-50
B-48
B-50
B-50
B-50

Vertical

Upright

B-58
B-60
B-60
B-58
B-60
B-60
B-60

B-68
B-70
B-70
B-68
B-70
B-70
B-70

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

5.5kW, 7.5kW

60Hz
Output Torque (Tout)
Nm
kgf m

64.3
57.1
50.7

1110
1250
1410

114
128
144

45

1590

163

40

1790

183

36

1990

203

32.1

2230

228

28.6

2510

256

25.4

2830

288

22.5

3180

325

20.0

3580

366

18.0

3980

406

16.1

4460

455

14.4

4970

508

Model
SF

Size

5.86
4.26
4.26
4.00
4.26
3.70
4.26
5.48
2.57
4.26
4.17
2.57
3.92
4.17
5.74
2.57
4.17
2.36
2.57
3.49
4.17
5.20
2.57
3.41
4.17
6.00
2.50
2.80
3.66
4.00
5.46
6.00
2.68
3.46
3.97
6.00
2.20
2.93
3.26
4.00
5.06
2.17
2.72
3.18
4.00
5.06

9030
9030
9030
9030
9035
9030
9035
9040
9030
9035
9040
9030
9035
9040
9045
9030
9040
9030
9035
9040
9045
9050
9035
9040
9045
9060
9035
9040
9045
9050
9055
9060
9040
9045
9050
9060
9040
9045
9050
9055
9060
9040
9045
9050
9055
9060

Page of Dimension Sheet

Assembly Reduction Horizontal

Ratio
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R4
R3
R4
R3
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

28
31.5
35.5
40
40
45
45
45
50
50
50
56
56
56
56
63
63
71
71
71
71
71
80
80
80
80
90
90
90
90
90
90
100
100
100
100
112
112
112
112
112
125
125
125
125
125

B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-48
B-44
B-50
B-44
B-48
B-44
B-48
B-44
B-50
B-48
B-48
B-48
B-50
B-48
B-48
B-48
B-48
B-50
B-48
B-48
B-48
B-48
B-50

Vertical

Upright

B-54
B-54
B-54
B-54
B054
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-58
B-54
B-60
B-54
B-58
B-54
B-58
B-54
B-60
B-58
B-58
B-58
B-60
B-58
B-58
B-58
B-58
B-60
B-58
B-58
B-58
B-58
B-60

B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-68
B-64
B-70
B-64
B-68
B-64
B-68
B-64
B-70
B-68
B-68
B-68
B-70
B-68
B-68
B-68
B-68
B-70
B-68
B-68
B-68
B-68
B-70

B - 17

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

10.7

6690

683

9.4

7640

780

8.3

8600

878

7.5

9550

975

6.7

10700

1090

6.0

11940

1220

5.4

13370

1370

4.8

15040

1540

4.2

16950

1730

3.8

19100

1950

3.3

21490

2190

Drive Unit

Dimension Selection
Tables
Tables

B - 18

SF
1.49
1.93
2.18
2.85
3.41
4.42
1.84
1.90
2.84
4.54
1.56
1.78
2.28
2.78
3.56
4.40
1.66
1.90
2.70
2.85
4.40
1.37
1.86
2.13
2.85
3.74
4.40
1.33
1.78
2.17
2.82
3.44
4.40
1.09
1.42
1.72
2.22
2.86
3.97
4.26
1.02
1.42
1.53
2.26
2.49
3.62
3.85
0.88
1.14
1.38
1.78
2.34
3.04
3.45
4.53
1.07
1.60
2.65
4.00
0.92
1.44
2.48
3.61

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

12.9

5570

569

11.3

6370

650

10.0

7160

731

9.0

7960

813

8.0

8910

910

7.2

9950

1020

6.4

11140

1140

5.7

12530

1280

5.1

14130

1440

4.5

15920

1630

4.0

17910

1830

7.5kW

Model
SF

Size

1.78
2.30
2.61
3.41
4.00
5.29
2.20
2.28
3.40
5.45
1.86
2.14
2.73
3.34
4.26
5.20
2.00
2.28
3.24
3.42
5.20
1.64
2.24
2.56
3.42
4.40
5.20
1.60
2.13
2.61
3.40
4.00
5.20
1.32
1.72
2.05
2.66
3.42
4.66
5.20
1.22
1.70
1.84
2.72
3.00
4.26
4.53
1.06
1.37
1.66
2.14
2.81
3.64
4.13
5.46
1.29
1.92
3.17
4.80
1.10
1.73
2.98
4.26

9040
9045
9050
9055
9060
9065
9045
9050
9055
9065
9045
9050
9055
9060
9065
9070
9050
9055
9060
9065
9070
9050
9055
9060
9065
9070
9075
9050
9055
9060
9065
9070
9075
9050
9055
9060
9065
9070
9075
9080
9050
9055
9060
9065
9070
9075
9080
9050
9055
9060
9065
9070
9075
9080
9085
9055
9065
9075
9085
9055
9065
9075
9085

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

140
140
140
140
140
140
160
160
160
160
180
180
180
180
180
180
200
200
200
200
200
224
224
224
224
224
224
250
250
250
250
250
250
280
280
280
280
280
280
280
315
315
315
315
315
315
315
355
355
355
355
355
355
355
355
400
400
400
400
450
450
450
450

B-48
B-48
B-48
B-48
B-50
B-50
B-48
B-48
B-48
B-50
B-48
B-48
B-48
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-48
B-50
B-50
B-50

Vertical

Upright

B-58
B-58
B-58
B-58
B-60
B-60
B-58
B-58
B-58
B-60
B-58
B-58
B-58
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-58
B-60
B-60
B-60

B-68
B-68
B-68
B-68
B-70
B-70
B-68
B-68
B-68
B-70
B-68
B-68
B-68
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-68
B-70
B-70
B-70

SELECTION Drive Unit Right Angle Shaft

11kW

Frequency Hz
Pole
P
5RGGFn1 r/min

50Hz
4
1500

60Hz
4
1800

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

93.8
83.3
75.0
67.0

1120
1260
1400
1570

114
129
143
160

60.0

1750

179

53.6

1960

200

47.6

2210

225

42.3

2490

254

37.5

2800

286

33.3

3150

322

30.0

3500

358

26.8

3920

400

23.8

4410

450

21.1

4970

508

18.8

5600

572

16.7

6300

644

15.0

7000

715

13.4

7840

801

12.0

8750

894

SF
3.90
3.90
4.63
4.18
3.72
4.90
3.36
4.45
5.00
2.44
3.90
4.37
2.44
3.54
3.81
2.34
2.44
3.72
4.37
2.10
2.44
3.11
4.07
4.54
1.46
2.44
3.89
4.45
1.46
2.23
2.37
3.27
3.63
4.72
1.46
2.37
3.54
4.72
1.34
1.46
1.99
2.37
2.90
3.81
4.54
1.46
1.94
2.37
3.81
1.42
1.59
2.09
2.30
3.09
3.36
4.81
1.52
1.97
2.26
3.36
1.25
1.67
1.85
2.30
2.81
3.40
4.90
1.23
1.54
1.80
2.30
2.90
3.40
4.54

Output Speed
r/min

11kW

60Hz
Output Torque (Tout)
Nm
kgf m

113
100
90.0
80.4

934
1050
1170
1310

95
107
119
133

72.0

1460

149

64.3

1630

167

57.1

1840

188

50.7

2070

212

45.0

2330

238

40.0

2630

268

36.0

2920

298

32.1

3270

334

28.6

3680

375

25.4

4140

423

22.5

4670

477

20.0

5250

536

18.0

5840

596

16.1

6540

667

14.4

7300

745

Model
SF

Size

4.63
4.63
5.54
5.00
4.45
5.81
4.00
5.27
5.90
2.90
4.63
5.18
2.90
4.27
4.63
2.72
2.90
4.55
5.25
2.52
2.90
3.73
4.87
5.45
1.75
2.90
4.67
5.36
1.75
2.67
2.84
3.91
4.36
5.63
1.75
2.84
4.27
5.72
1.60
1.75
2.38
2.84
3.54
4.54
5.45
1.75
2.32
2.84
4.63
1.70
1.90
2.50
2.72
3.72
4.09
5.76
1.82
2.36
2.70
4.09
1.50
2.00
2.22
2.72
3.45
4.09
5.90
1.48
1.85
2.17
2.72
3.45
4.09
5.45

9030
9030
9030
9030
9030
9035
9030
9035
9040
9030
9035
9040
9030
9035
9040
9030
9035
9040
9045
9030
9035
9040
9045
9050
9030
9035
9045
9050
9030
9035
9040
9045
9050
9055
9030
9040
9050
9055
9030
9035
9040
9045
9050
9055
9060
9035
9040
9045
9055
9035
9040
9045
9050
9055
9060
9065
9040
9045
9050
9060
9040
9045
9050
9055
9060
9065
9070
9040
9045
9050
9055
9060
9065
9070

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R2
R2
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R4
R3
R3
R3
R4
R3
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

16
18
20
22.4
25
25
28
28
28
31.5
31.5
31.5
35.5
35.5
35.5
40
40
40
40
45
45
45
45
45
50
50
50
50
56
56
56
56
56
56
63
63
63
63
71
71
71
71
71
71
71
80
80
80
80
90
90
80
90
90
90
90
100
100
100
100
112
112
112
112
112
112
112
125
125
125
125
125
125
125

B-42
B-42
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-46
B-44
B-48
B-44
B-44
B-44
B-48
B-44
B-48
B-44
B-50
B-46
B-48
B-48
B-48
B-50
B-48
B-48
B-48
B-48
B-50
B-50
B-50
B-48
B-48
B-48
B-48
B-50
B-50
B-50

Vertical

Upright

B-52
B-52
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-56
B-54
B-58
B-54
B-54
B-54
B-58
B-54
B-58
B-54
B-60
B-56
B-58
B-58
B-58
B-60
B-58
B-58
B-58
B-58
B-60
B-60
B-60
B-58
B-58
B-58
B-58
B-60
B-60
B-60

B-62
B-62
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-66
B-64
B-68
B-64
B-64
B-64
B-68
B-64
B-68
B-64
B-70
B-66
B-68
B-68
B-68
B-70
B-68
B-68
B-68
B-68
B-70
B-70
B-70
B-68
B-68
B-68
B-68
B-70
B-70
B-70

B - 19

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

10.7

9800

1000

9.4

11210

1140

8.3

12610

1290

7.5

14010

1430

6.7

15690

1600

6.0

17510

1790

5.4

19610

2000

4.8

22060

2250

4.2

24860

2540

3.8

28010

2860

3.3

31520

3220

Dimension Selection
Tables
Tables

Drive Unit

B - 20

SF
1.01
1.31
1.49
1.94
2.32
3.01
3.72
1.25
1.30
1.93
3.10
4.81
1.06
1.21
1.55
1.90
2.42
3.00
4.00
4.72
1.13
1.30
1.84
1.94
3.00
4.45
0.93
1.27
1.45
1.94
2.55
3,00
3.90
4.90
0.90
1.21
1.48
1.92
2.34
3.00
3.45
4.72
0.97
1.17
1.51
1.95
2.70
2.90
4.09
0.97
1.04
1.54
1.70
2.47
2.62
3.63
0.94
1.21
1.60
2.07
2.35
3.09
1.09
1.80
2.72
0.98
1.69
2.46

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

12.9

8170

834

11.3

9340

953

10.0

10510

1070

9.0

11670

1190

8.0

13070

1330

7.2

14590

1490

6.4

16340

1670

5.7

18380

1880

5.1

20720

2120

4.5

23340

2380

4.0

26260

2680

11kW

Model
SF

Size

1.21
1.57
1.78
2.32
2.72
3.60
4.54
1.50
1.55
2.31
3.71
5.72
1.27
1.46
1.86
2.28
2.90
3.54
4.81
5.63
1.36
1.55
2.20
2.33
3.54
5.36
1.11
1.52
1.74
2.33
3.00
3.54
4.63
5.90
1.09
1.45
1.78
2.31
2.72
3.54
4.09
5.63
1.17
1.40
1.81
2.33
3.18
3.54
4.90
1.16
1.25
1.85
2.04
2.90
3.09
4.36
1.13
1.46
1.91
2.48
2.81
3.72
1.30
2.16
3.27
1.18
2.03
2.90

9040
9045
9050
9055
9060
9065
9070
9045
9050
9055
9065
9075
9045
9050
9055
9060
9065
9070
9075
9080
9050
9055
9060
9065
9070
9080
9050
9055
9060
9065
9070
9075
9080
9085
9050
9055
9060
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9085
9060
9065
9070
9075
9080
9085
9065
9075
9085
9065
9075
9085

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

140
140
140
140
140
140
140
160
160
160
160
160
180
180
180
180
180
180
180
180
200
200
200
200
200
200
224
224
224
224
224
224
224
224
250
250
250
250
250
250
250
250
280
280
280
280
280
280
280
315
315
315
315
315
315
315
355
355
355
355
355
355
400
400
400
450
450
450

B-48
B-48
B-48
B-48
B-50
B-50
B-50
B-48
B-48
B-48
B-50
B-50
B-48
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-58
B-58
B-58
B-58
B-60
B-60
B-60
B-58
B-58
B-58
B-60
B-60
B-58
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-68
B-68
B-68
B-68
B-70
B-70
B-70
B-68
B-68
B-68
B-70
B-70
B-68
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

SELECTION Drive Unit Right Angle Shaft

15kW

Frequency Hz
Pole
P
5RGGFn1 r/min

50Hz
4
1500

60Hz
4
1800

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

120
107

1190
1340

122
137

93.8

1530

156

83.3

1720

176

75.0

1910

195

67.0

2140

218

60.0

2390

244

53.6

2670

273

47.6

3010

307

42.3

3390

346

37.5

3820

390

33.3

4300

439

30.0

4780

488

26.8

5350

546

23.8

6020

614

21.1

6780

692

SF
4.06
4.06
2.86
4.06
4.20
2.86
4.06
4.20
3.40
4.46
3.06
4.46
2.73
3.60
4.47
2.46
3.26
3.66
4.50
1.79
2.86
3.20
4.50
1.79
2.60
2.80
3.85
4.33
1.72
1.79
2.73
3.20
4.06
1.54
1.79
2.28
2.98
3.33
4.53
1.07
1.79
2.85
3.26
4.33
4.93
1.07
1.64
1.74
2.40
2.66
3.46
4.26
1.07
1.74
2.60
3.46
4.00
4.93
0.98
1.07
1.46
1.74
2.13
2.80
3.33
4.48

Output Speed
r/min

15kW

60Hz
Output Torque (Tout)
Nm
kgf m

144
129

995
1110

102
114

113

1270

130

100

1430

146

90.0

1590

163

80.4

1780

182

72.0

1990

203

64.3

2230

228

57.1

2510

256

50.7

2830

288

45.0

3180

325

40.0

3580

366

36.0

3980

406

32.1

4460

455

28.6

5010

512

25.4

5650

577

Model
SF

Size

4.86
4.86
3.40
4.86
5.00
3.40
4.86
5.00
4.06
5.20
3.66
5.20
3.26
4.26
5.20
2.93
3.86
4.33
5.20
2.13
3.40
3.80
5.20
2.13
3.13
3.40
4.61
5.20
2.00
2.13
3.34
3.85
4.86
1.85
2.13
2.74
3.57
4.00
5.46
1.28
2.13
3.42
3.93
5.20
5.60
1.28
1.96
2.08
2.87
3.20
4.13
5.13
1.28
2.08
3.13
4.20
4.53
5.60
1.18
1.28
1.74
2.08
2.60
3.33
4.00
5.36

9030
9030
9030
9035
9040
9030
9035
9040
9030
9040
9030
9040
9030
9035
9040
9030
9035
9040
9045
9030
9035
9040
9045
9030
9035
9040
9045
9050
9030
9035
9040
9045
9050
9030
9035
9040
9045
9050
9055
9030
9035
9045
9050
9055
9060
9030
9035
9040
9045
9050
9055
9060
9030
9040
9050
9055
9060
9065
9030
9035
9040
9045
9050
9055
9060
9065

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R2
R2
R2
R2
R2
R2
R2
R2
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3

12.5
14
16
16
16
18
18
18
20
20
22.4
22.4
25
25
25
28
28
28
28
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
45
45
45
45
45
45
50
50
50
50
50
50
56
56
56
56
56
56
56
63
63
63
63
63
63
71
71
71
71
71
71
71
71

B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-46
B-44
B-44
B-44
B-44
B-44
B-44
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-44
B-44
B-44
B-46
B-46

Vertical

Upright

B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-56
B-54
B-54
B-54
B-54
B-54
B-54
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-54
B-54
B-54
B-56
B-56

B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-66
B-64
B-64
B-64
B-64
B-64
B-64
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-64
B-64
B-64
B-66
B-66

B - 21

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

7640

780

16.7

8600

878

Drive Unit

15.0

9550

975

13.4

10700

1090

12.0

11940

1220

10.7

13370

1370

9.4

15280

1560

8.3

17190

1760

7.5

19100

1950

Dimension Selection
Tables
Tables

18.8

B - 22

SF
1.07
1.42
1.74
2.80
4.00
4.40
1.04
1.16
1.53
1.68
2.26
2.46
3.53
4.40
1.12
1.44
1.66
2.46
4.33
0.92
1.22
1.36
1.68
2.06
2.50
3.60
4.40
0.90
1.13
1.32
1.68
2.13
2.50
3.33
4.40
5.00
0.96
1,09
1.42
1.70
2.21
2.73
3.86
4.33
0.92
0.95
1.42
2.27
3.53
3.80
0.89
1.14
1.39
1.78
2.93
3.46
4.53
0.83
0.95
1.35
1.42
2.20
3.26
3.80

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

22.5

6370

650

20.0

7160

731

18.0

7960

813

16.1

8910

910

14.4

9950

1020

12.9

11140

1140

11.3

12730

1300

10.0

14330

1460

9.0

15920

1630

15kW

Model
SF

Size

1.28
1.70
2.08
3.40
4.53
5.33
1.25
1.40
1.83
2.00
2.73
3.00
4.22
5.33
1.34
1.73
1.98
3.00
5.20
1.10
1.46
1.63
2.00
2.53
3.00
4.33
5.33
1.08
1.36
1.59
2.00
2.53
3.00
4.00
5.33
6.00
1.15
1.30
1.70
2.00
2.64
3.33
4.59
5.20
1.10
1.14
1.70
2.72
4.20
4.53
1.07
1.36
1.67
2.13
3.53
4.13
5.46
1.00
1.14
1.62
1.71
2.0
3.93
4.53

9035
9040
9045
9055
9065
9070
9035
9040
9045
9050
9055
9060
9065
9070
9040
9045
9050
9060
9070
9040
9045
9050
9055
9060
9065
9070
9075
9040
9045
9050
9055
9060
9065
8970
9075
9080
9045
9050
9055
9060
9065
9070
9075
9080
9045
9050
9055
9065
9075
9080
9050
9055
9060
9065
9075
9080
9085
9050
9055
9060
9065
9070
9080
9085

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R3
R4
R3
R3
R3
R4
R3
R4
R3
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

80
80
80
80
80
80
90
90
90
90
90
90
90
90
100
100
100
100
100
112
112
112
112
112
112
112
112
125
125
125
125
125
125
125
125
125
140
140
140
140
140
140
140
140
160
160
160
160
160
160
180
180
180
180
180
180
180
200
200
200
200
200
200
200

B-44
B-48
B-44
B-44
B-46
B-50
B-44
B-48
B-44
B-48
B-44
B-50
B-46
B-50
B-48
B-48
B-48
B-50
B-50
B-48
B-48
B-48
B-48
B-50
B-50
B-50
B-50
B-48
B-48
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-48
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-54
B-58
B-54
B-54
B-56
B-60
B-54
B-58
B-54
B-58
B-54
B-60
B-56
B-60
B-58
B-58
B-58
B-60
B-60
B-58
B-58
B-58
B-58
B-60
B-60
B-60
B-60
B-58
B-58
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-58
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60

B-64
B-68
B-64
B-64
B-64
B-70
B-64
B-68
B-64
B-68
B-64
B-70
B-66
B-70
B-68
B-68
B-68
B-70
B-70
B-68
B-68
B-68
B-68
B-70
B-70
B-70
B-70
B-68
B-68
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-68
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

6.7

21390

2180

6.0

23880

2440

5.4

26740

2730

4.8

30080

3070

4.2

33900

3460

3.8

38200

3900

3.3

42980

4390

18.5kW

SF
0.93
1.06
1.42
1.87
2.20
2.86
3.60
0.89
1.08
1.41
1.72
2.20
2.53
3.46
0.86
1.11
1.43
1.98
2.13
3.00
1.13
1.24
1.81
1.92
2.66
0.89
1.17
1.52
1.72
2.26
1.32
2.00
1.24
1.80

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

8.0

17830

1820

7.2

19900

2030

6.4

22280

2280

5.7

25070

2560

5.1

28250

2880

4.5

31830

3250

4.0

35810

3660

50Hz
4
1500

Model
SF

Size

1.12
1.28
1.71
2.20
2.60
3.40
4.33
1.06
1.30
1.70
2.00
2.60
3.00
4.13
1.02
1.33
1.71
2.33
2.60
3.60
1.36
1.50
2.13
2.26
3.20
1.07
1.40
1.82
2.06
2.73
1.58
2.40
1.49
2.13

9055
9060
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9085
9060
9065
9070
9075
9080
9085
9065
9070
9075
9080
9085
9065
9070
9075
9080
9085
9075
9085
9075
9085

Output Speed
r/min
150
134
120
107

1180
1320
1470
1650

120
135
150
168

93.8

1880

192

83.3

2120

216

75.0

2360

241

67.0

2640

269

60.0

2940

301

SF
5.29
5.29
4.75
4.75
3.29
3.40
4.37
3.29
3.40
4.37
2.32
3.62
2.32
3.62
2.91
3.62

Output Speed
r/min

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

224
224
224
224
224
224
224
250
250
250
250
250
250
250
280
280
280
280
280
280
315
315
315
315
315
355
355
355
355
355
400
400
450
450

B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

15kW, 18.5kW

60Hz
Output Torque (Tout)
Nm
kgf m

180
161
144
129

982
1100
1230
1370

100
112
125
140

113

1570

160

100

1770

180

90.0

1960

200

80.4

2200

224

72.0

2450

251

Model
SF

Size

Assembly

6.10
6.10
5.40
5.40
3.94
4.05
5.24
3.94
4.05
5.24
2.75
4.21
2.75
4.21
3.25
4.21

9035
9035
9035
9035
9035
9040
9045
9035
9040
9045
9035
9040
9035
9040
9035
9040

R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R3
R2
R3
R3
R3

Page of Dimension Sheet

Reduction
Horizontal
Ratio
10
11.2
12.5
14
16
16
16
18
18
18
20
20
22.4
22.4
25
25

B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-44
B-42
B-44
B-44
B-44

Vertical

Upright

B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-54
B-52
B-54
B-54
B-54

B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-64
B-62
B-64
B-64
B-64

B - 23

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

Drive Unit

Dimension Selection
Tables
Tables

B - 24

50Hz
Output Torque (Tout)
Nm
kgf m

53.6

3300

337

47.6

3710

379

42.3

4180

427

37.5

4710

481

33.3

5300

541

30.0

5890

601

26.8

6600

673

23.8

7420

758

21.1

8360

854

18.8

9420

962

SF
2.64
2.97
3.65
4.32
2.32
2.60
3.65
4.27
2.10
2.27
3.12
3.51
4.45
1.45
2.21
2.60
3.29
4.27
1.45
1.85
2.42
2.70
3.67
4.37
1.45
2.31
2.64
3.51
4.00
1.32
1.41
1.94
2.16
2.81
3.45
4.61
1.41
2.10
2.81
3.24
4.00
4.75
0.87
1.18
1.41
1.72
2.27
2.70
3.63
4.54
0.87
1.15
1.41
2.27
3.24
3.56
4.75

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

64.3

2750

281

57.1

3090

316

50.7

3480

356

45.0

3930

401

40.0

4420

451

36.0

4910

501

32.1

5500

561

28.6

6180

631

25.4

6970

711

22.5

7850

802

18.5kW

Model
SF

Size

3.13
3.51
4.21
5.18
2.75
3.08
4.21
4.91
2.54
2.75
3.74
4.21
5.40
1.72
2.70
3.12
3.94
4.91
1.72
2.22
2.89
3.24
4.43
5.24
1.72
2.77
3.18
4.21
4.54
1.58
1.69
2.33
2.59
3.35
4.16
5.51
1.69
2.54
3.40
3.67
4.54
5.40
1.04
1.41
1.69
2.10
2.70
3.24
4.35
5.40
1.04
1.38
1.69
2.75
3.67
4.32
5.40

9035
9040
9045
9050
9035
9040
9045
9050
9035
9040
9045
9050
9055
9035
9040
9045
9050
9055
9035
9040
9045
9050
9055
9060
9035
9045
9050
9055
9060
9035
9040
9045
9050
9055
9060
9065
9040
9050
9055
9060
9065
9070
9035
9040
9045
9050
9055
9060
9065
9070
9035
9040
9045
9055
9065
9070
9075

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R4
R3
R3
R3
R4
R3

28
28
28
28
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
45
45
45
45
45
45
50
50
50
50
50
56
56
56
56
56
56
56
63
63
63
63
63
63
71
71
71
71
71
71
71
71
80
80
80
80
80
80
80

B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-44
B-46
B-44
B-44
B-44
B-44
B-46
B-44
B-44
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-48
B-44
B-44
B-46
B-50
B-46

Vertical

Upright

B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-54
B-56
B-54
B-54
B-54
B-54
B-56
B-54
B-54
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-58
B-54
B-54
B-56
B-60
B-56

B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-64
B-66
B-64
B-64
B-64
B-64
B-66
B-64
B-64
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-68
B-64
B-64
B-66
B-70
B-66

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

16.7

10600

1080

15.0

11780

1200

13.4

13190

1350

12.0

14720

1500

10.7

16490

1680

9.4

18850

1920

8.3

21200

2160

7.5

23560

2410

6.7

26380

2690

6.0

29450

3010

SF
0.84
0.94
1.24
1.36
1.83
2.00
2.86
3.56
4.75
0.90
1.17
1.34
2.00
3.51
0.99
1.10
1.36
1.67
2.02
2.91
3.56
4.59
0.91
1.07
1.36
1.72
2.02
2.70
3.56
4.05
0.88
1.15
1.38
1.79
2.21
3.13
3.51
4.81
1.15
1.84
1.78
2.86
3.08
4.27
0.92
1.12
1.44
1.78
2.37
2.81
3.67
1.09
1.15
1.78
2.64
3.08
0.86
1.15
1.51
1.78
2.32
2.91
0.88
1.14
1.39
1.78
2.05
2.81

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

20.0

8830

902

18.0

9820

1000

16.1

10990

1120

14.4

12270

1250

12.9

13740

1400

11.3

15700

1600

10.0

17670

1800

9.0

19630

2000

8.0

21990

2240

7.2

24540

2510

Model
SF

Size

1.01
1.13
1.48
1.62
2.21
2.43
3.42
4.32
5.40
1.08
1.40
1.61
2,43
4.21
1.18
1.32
1.62
2.05
2.43
3.51
4.32
5.51
1.10
1.29
1.62
2.05
2.43
3.24
4.32
4.86
1.05
1.38
1.62
2.14
2.70
3.72
4.21
5.78
1.37
2.21
2.10
3.40
3.67
5.13
1.10
1.35
1.73
2.10
2.86
3.35
4.43
1.31
1.38
2.10
3.18
3.67
1.03
1.38
1.78
2.10
2.75
3.51
1.05
1.37
1.62
2.10
2.43
3.35

9035
9040
9045
9050
9055
9060
9065
9070
9075
9040
9045
9050
9060
9070
9045
9050
9055
9060
9065
9070
9075
9080
9045
9050
9055
9060
9065
9070
9075
9080
9050
9055
9060
9065
9070
9075
9080
9085
9055
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9085
9060
9065
9070
9080
9085
9060
9065
9070
9075
9080
9085
9060
9065
9070
9075
9080
9085

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R3
R4
R3
R4
R3
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

18.5kW

90
90
90
90
90
90
90
90
90
100
100
100
100
100
112
112
112
112
112
112
112
112
125
125
125
125
125
125
125
125
140
140
140
140
140
140
140
140
160
160
160
160
160
160
180
180
180
180
180
180
180
200
200
200
200
200
224
224
224
224
224
224
250
250
250
250
250
250

B-44
B-48
B-44
B-48
B-44
B-50
B-46
B-50
B-46
B-48
B-48
B-48
B-50
B-50
B-48
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-54
B-58
B-54
B-58
B-54
B-60
B-56
B-60
B-56
B-58
B-58
B-58
B-60
B-60
B-58
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-64
B-68
B-64
B-68
B-64
B-70
B-66
B-70
B-66
B-68
B-68
B-68
B-70
B-70
B-68
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

B - 25

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

Drive Unit

Dimension Selection
Tables
Tables

50Hz
Output Torque (Tout)
Nm
kgf m

5.4

32980

3370

4.8

37100

3790

4.2

41810

4270

3.8

47110

4810

3.3

53000

5410

22kW

SF
0.90
1.16
1.61
1.72
2.43
0.91
1.01
1.47
1.56
2.16
0.95
1.23
1.40
1.83
1.07
1.62
1.00
1.46

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

6.4

27480

2810

5.7

30920

3160

5.1

34840

3560

4.5

39260

4010

4.0

44170

4510

50Hz
4
1500

Model
SF

Size

1.08
1.38
1.89
2.10
2.91
1.10
1.21
1.72
1.83
2.59
1.14
1.47
1.67
2.21
1.28
1.94
1.21
1.72

9065
9070
9075
9080
9085
9065
9070
9075
9080
9085
9070
9075
9080
9085
9075
9085
9075
9085

Output Speed
r/min

B - 26

188
167
150
134
120
107

1120
1260
1400
1570
1750
1960

114
129
143
160
179
200

93.8

2240

229

83.3

2520

257

75.0

2800

286

67.0

3140

320

60.0

3500

358

SF
4.68
4.68
4.45
4.45
4.00
4.00
2.77
2.86
3.68
2.77
2.86
3.68
3.04
4.31
4.95
3.04
4.31
4.95
2.45
3.05
4.31
4.95

Output Speed
r/min

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

280
280
280
280
280
315
315
315
315
315
355
355
355
355
400
400
450
450

B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

18.5kW, 22kW

60Hz
Output Torque (Tout)
Nm
kgf m

225
200
180
161
144
129

934
1050
1170
1310
1460
1630

95
107
119
133
149
167

113

1870

191

100

2100

215

90.0

2330

238

80.4

2610

267

72.0

2920

298

Model
SF

Size

5.45
5.45
5.13
5.13
4.54
4.54
3.31
3.40
4.40
3.31
3.40
4.40
3.54
4.90
5.59
3.54
4.90
5.59
2.90
3.54
4.90
5.59

9035
9035
9035
9035
9035
9035
9035
9040
9045
9035
9040
9045
9040
9050
9060
9040
9050
9060
9035
9040
9050
9060

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3

8
9
10
11.2
12.5
14
16
16
16
18
18
18
20
20
20
22.4
22.4
22.4
25
25
25
25

B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-44
B-44
B-46
B-44
B-44
B-46
B-44
B-44
B-44
B-46

Vertical

Upright

B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-54
B-54
B-56
B-54
B-54
B-56
B-54
B-54
B-54
B-56

B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-64
B-64
B-66
B-64
B-64
B-66
B-64
B-64
B-64
B-66

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

53.6

3920

400

47.6

4410

450

42.3

4970

508

37.5

5600

572

33.3

6300

644

30.0

7000

715

26.8

7840

801

23.8

8820

901

21.1

9940

1020

SF
2.22
2.50
3.07
3.63
4.31
4.95
1.95
2.18
3.07
3.59
4.31
4.95
1.77
1.90
2.62
2.95
3.81
4.22
4.95
1.22
1.86
2.18
2.77
3.59
4.22
1.22
1.55
2.03
2.27
3.09
3.68
4.22
1.22
1.94
2.22
2.95
3.36
4.22
4.90
1.11
1.18
1.63
1.81
2.36
2.90
3.87
4.86
1.18
1.77
2.36
2.72
3.36
4.00
4.90
0.99
1.18
1.45
1.90
2.27
3.05
3.81
4.90

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

64.3

3270

334

57.1

3680

375

50.7

4140

423

45.0

4670

477

40.0

5250

536

36.0

5840

596

32.1

6540

667

28.6

7350

751

25.4

8290

846

Model
SF

Size

2.63
2.95
3.54
4.36
4.90
5.59
2.31
2.59
3.54
4.13
4.90
5.59
2.13
2.31
3.14
3.54
4.54
4.77
5.59
1.45
2.27
2.62
3.31
4.13
4.77
1.45
1.86
2.43
2.72
3.72
4.40
4.77
1.45
2.33
2.68
3.54
3.81
4.77
5.59
1.33
1.42
1.95
2.18
2.81
3.50
4.63
5.59
1.42
2.13
2.86
3.09
3.81
4.54
5.59
1.19
1.42
1.77
2.27
2.72
3.65
4.54
5.59

9035
9040
9045
9050
9055
9060
9035
9040
9045
9050
9055
9065
9035
9040
9045
9050
9055
9060
9065
9035
9040
9045
9050
9055
9060
9035
9040
9045
9050
9055
9060
9065
9035
9045
9050
9055
9060
9065
9070
9035
9040
9045
9050
9055
9060
9065
9070
9040
9050
9055
9060
9065
9070
9075
9040
9045
9050
9055
9060
9065
9070
9075

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3

22kW

28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
45
45
45
45
45
45
45
50
50
50
50
50
50
50
56
56
56
56
56
56
56
56
63
63
63
63
63
63
63
71
71
71
71
71
71
71
71

B-44
B-44
B-44
B-44
B-44
B-46
B-44
B-44
B-44
B-44
B-44
B-46
B-44
B-44
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-44
B-44
B-46
B-44
B-44
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-46

Vertical

Upright

B-54
B-54
B-54
B-54
B-54
B-56
B-54
B-54
B-54
B-54
B-54
B-56
B-54
B-54
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-54
B-54
B-56
B-54
B-54
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-56

B-64
B-64
B-64
B-64
B-64
B-66
B-64
B-64
B-64
B-64
B-64
B-66
B-64
B-64
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-64
B-64
B-66
B-64
B-64
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-66

B - 27

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

Drive Unit

Dimension Selection
Tables
Tables

50Hz
Output Torque (Tout)
Nm
kgf m

18.8

11210

1140

16.7

12610

1290

15.0

14010

1430

13.4

15690

1600

12.0

17510

1790

10.7

19610

2000

9.4

22410

2290

8.3

25210

2570

7.5

28010

2860

6.7

31370

3200

6.0

35020

3580

B - 28

SF
0.97
1.18
1.90
2.72
3.00
4.00
4.54
1.04
1.15
1.54
1.68
2.40
3.00
4.00
4.54
0.98
1.13
1.68
2.95
4.50
0.83
0.92
1.15
1.40
1.70
2.45
3.00
3.86
4.54
0.90
1.15
1.45
1.70
2.27
3.00
3.40
4.54
0.97
1.16
1.50
1.86
2.63
2.95
4.04
0.96
1.55
2.40
2.59
3.59
0.95
1.21
1.50
2.00
2.36
3.09
0.92
0.97
1.50
2.22
2.59
0.97
1.27
1.50
1.95
2.45
0.96
1.17
1.50
1.72
2.36

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

22.5

9340

953

20.0

10510

1070

18.0

11670

1190

16.1

13070

1330

14.4

14590

1490

12.9

16340

1670

11.3

18680

1910

10.0

21010

2150

9.0

23340

2380

8.0

26150

2670

7.2

29180

2980

22kW

Model
SF

Size

1.16
1.42
2.31
3.09
3.63
4.54
5.13
1.25
1.36
1.86
2.04
2.88
3.63
4.54
5.13
1.18
1.35
2.04
3.54
5.13
1.00
1.11
1.36
1.72
2.04
2.95
3.63
4.63
5.13
1.08
1.36
1.72
2.04
2.72
3.63
4.09
5.13
1.16
1.36
1.80
2.27
3.13
3.54
4.86
1.15
1.85
2.86
3.09
4.31
1.14
1.45
1.77
2.40
2.81
3.72
1.10
1.16
1.77
2.68
3.09
1.16
1.50
1.77
2.31
2.95
1.15
1.36
1.77
2.04
2.81

9040
9045
9055
9065
9070
9075
9080
9045
9050
9055
9060
9065
9070
9075
9080
9045
9050
9060
9070
9080
9045
9050
9055
9060
9065
9070
9075
9080
9085
9050
9055
9060
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9085
9055
9065
9075
9080
9085
9060
9065
9070
9075
9080
9085
9060
9065
9070
9080
9085
9065
9070
9075
9080
9085
9065
9070
9075
9080
9085

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R4
R3
R3
R3
R4
R3
R4
R3
R4
R3
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

80
80
80
80
80
80
80
90
90
90
90
90
90
90
90
100
100
100
100
100
112
112
112
112
112
112
112
112
112
125
125
125
125
125
125
125
125
140
140
140
140
140
140
140
160
160
160
160
160
180
180
180
180
180
180
200
200
200
200
200
224
224
224
224
224
250
250
250
250
250

B-48
B-44
B-44
B-46
B-50
B-46
B-50
B-44
B-48
B-44
B-50
B-46
B-50
B-46
B-50
B-48
B-48
B-50
B-50
B-50
B-48
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-58
B-54
B-54
B-56
B-60
B-56
B-60
B-54
B-58
B-54
B-60
B-56
B-60
B-56
B-60
B-58
B-58
B-60
B-60
B-60
B-58
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-68
B-64
B-64
B-66
B-70
B-66
B-70
B-64
B-68
B-64
B-70
B-66
B-70
B-66
B-70
B-68
B-68
B-70
B-70
B-70
B-68
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

5.4

39220

4000

4.8

44120

4500

4.2

49720

5080

3.8

56030

5720

3.3

63030

6440

30kW

SF
0.97
1.35
1.45
2.04
0.85
1.23
1.31
1.81
1.03
1.17
1.54
0.90
1.36
0.84
1.23

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

6.4

32680

3340

5.7

36770

3750

5.1

41440

4230

4.5

46690

4770

4.0

52530

5360

50Hz
4
1500

Model
SF

Size

1.16
1.59
1.77
2.45
1.02
1.45
1.54
2.18
1.24
1.40
1.86
1.08
1.63
1.01
1.45

9070
9075
9080
9085
9070
9075
9080
9085
9075
9080
9085
9075
9085
9075
9085

60Hz
4
1800

Output Speed
r/min
238
211
188
167

1200
1360
1530
1720

123
138
156
176

150

1910

195

134

2140

218

120
107

2390
2670

244
273

93.8

3060

312

83.3

3440

351

75.0

3820

390

67.0

4280

437

SF
4.59
4.59
4.13
4.13
3.76
4.80
3.76
4.80
3.90
3.90
2.10
2.70
2.10
2.70
2.23
3.16
3.63
2.23
3.16
3.63

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

286
254
225
200

1000
1130
1270
1430

102
115
130
146

180

1590

163

161

1780

182

144
129

1990
2230

203
228

113

2550

260

100

2870

293

90.0

3180

325

80.4

3570

364

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

280
280
280
280
315
315
315
315
355
355
355
400
400
450
450

B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

* marked model upright type need additional cooling system for

continuous operation.

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

22kW, 30kW

Model
SF

Size

4.59
4.59
4.59
4.59
4.26
5.76
4.26
5.76
4.66
4.66
2.50
3.23
2.50
3.23
2.60
3.60
4.09
2.60
3.60
4.09

9040
9040
9040
9040
9040
9045
9040
9045
9045
9045
9040
9045
9040
9045
9040
9050
9060
9040
9050
9060

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R3
R3
R3
R3
R3
R3

6.3
7.1
8
9
10
10
11.2
11.2
12.5
14
16
16
18
18
20
20
20
22.4
22.4
22.4

B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-44
B-44
B-46
B-44
B-44
B-46

Vertical

Upright

B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-54
B-54
B-56
B-54
B-54
B-56

B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-64
B-64
B-66
B-64
B-64
B-66

B - 29

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

Drive Unit

Dimension Selection
Tables
Tables

B - 30

50Hz
Output Torque (Tout)
Nm
kgf m

60.0

4780

488

53.6

5350

546

47.6

6020

614

42.3

6780

692

37.5

7640

780

33.3

8600

878

30.0

9550

975

26.8

10700

1090

23.8

12030

1230

21.1

13560

1380

SF
2.23
3.16
3.63
1.83
2.25
2.66
3.16
3.63
1.60
2.25
2.63
3.10
3.63
4.53
1.40
1.92
2.16
2.80
3.10
3.63
4.53
1.36
1.60
2.03
2.63
3.10
4.53
1.14
1.49
1.66
2.26
2.70
3.10
4.50
1.42
1.63
2.16
2.46
3.10
3.60
4.53
0.87
1.20
1.33
1.73
2.13
2.84
3.56
4.53
0.87
1.30
1.73
2.00
2.46
2.93
3.60
0.87
1.06
1.40
1.66
2.24
2.80
3.60

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

72.0

3980

406

64.3

4460

455

57.1

5010

512

50.7

5650

577

45.0

6370

650

40.0

7160

731

36.0

7960

813

32.1

8910

910

28.6

10030

1020

25.4

11300

1150

30kW

Model
SF

Size

2.60
3.60
4.09
2.16
2.60
3.20
3.60
4.09
1.90
2.60
3.03
3.50
4.10
5.16
1.70
2.30
2.60
3.33
3.50
4.10
5.16
1.67
1.92
2.43
3.03
3.50
5.16
1.37
1.78
2.00
2.73
3.23
3.50
5.16
1.71
1.96
2.60
2.80
3.50
4.09
5.16
1.04
1.43
1.60
2.06
2.56
3.40
4.09
5.16
1.04
1.56
2.10
2.26
2.80
3.33
4.09
1.04
1.30
1.66
2.00
2.68
3.33
4.09

9040
9050
9060
9040
9045
9050
9055
9060
9040
9045
9050
9060
9065
9070
9040
9045
9050
9055
9060
9065
9070
9040
9045
9050
9055
9060
9070
9040
9045
9050
9055
9060
9065
9070
9045
9050
9055
9060
9065
9070
9075
9040
9045
9050
9055
9060
9065
9070
9075
9040
9050
9055
9060
9065
9070
9075
9045
9050
9055
9060
9065
9070
9075

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3

25
25
25
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
45
45
45
45
45
45
45
50
50
50
50
50
50
50
56
56
56
56
56
56
56
56
63
63
63
63
63
63
63
71
71
71
71
71
71
71

B-44
B-44
B-46
B-44
B-44
B-44
B-44
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-46

Vertical

Upright

B-54
B-54
B-56
B-54
B-54
B-54
B-54
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-56

B-64
B-64
B-66
B-64
B-64
B-64
B-64
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-66

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

18.8

15280

1560

16.7

17190

1760

15.0

19100

1950

13.4

21390

2180

12.0

23880

2440

10.7

26740

2730

9.4

30560

3120

8.3

34380

3510

7.5

38200

3900

6.7

42780

4370

6.0

47750

4880

5.4

53480

5460

4.8

60170

6140

4.2

67810

6920

3.8
3.3

76400
85950

7800
8780

SF
0.87
1.40
2.00
2.20
2.93
3.33
0.84
1.13
1.23
1.76
2.20
2.93
3.33
0.84
1.23
2.16
3.30
0.84
1.03
1.25
1.80
2.20
2.83
3.33
0.84
1.06
1.25
1.66
2.20
2.50
3.33
0.85
1.10
1.36
1.93
2.16
2.96
1.13
1.76
1.90
2.63
0.89
1.10
1.46
1.73
2.26
1.10
1.63
1.90
0.93
1.10
1.43
1.80
0.86
1.10
1.26
1.73
0.99
1.06
1.50
0.90
0.96
1.33
0.86
1.13
1.00
0.90

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

22.5

12730

1300

20.0

14330

1460

18.0

15920

1630

16.1

17830

1820

14.4

19900

2030

12.9

22280

2280

11.3

25470

2600

10.0

28650

2930

9.0

31830

3250

8.0

35650

3640

7.2

39790

4060

6.4

44570

4550

5.7

50140

5120

5.1

56500

5770

4.5
4.0

63670
71630

6500
7310

Model
SF

Size

1.04
1.70
2.26
2.66
3.33
3.76
1.00
1.36
1.50
2.11
2.66
3.33
3.76
1.00
1.50
2.60
3.76
1.00
1.26
1.50
2.16
2.66
3.40
3.76
1.00
1.26
1.50
2.00
2.66
3.00
3.76
1.00
1.32
1.66
2.29
2.60
3.56
1.36
2.10
2.26
3.16
1.06
1.30
1.76
2.06
2.73
1.30
1.96
2.26
1.10
1.30
1.70
2.16
1.00
1.30
1.50
2.06
1.16
1.30
1.80
1.06
1.13
1.60
1.03
1.36
1.20
1.06

9045
9055
9065
9070
9075
9080
9050
9055
9060
9065
9070
9075
9080
9055
9060
9070
9080
9055
9060
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9085
9060
9065
9070
9075
9080
9085
9065
9075
9080
9085
9065
9070
9075
9080
9085
9070
9080
9085
9070
9075
9080
9085
9070
9075
9080
9085
9075
9080
9085
9075
9080
9085
9080
9085
9085
9085

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R3
R3
R3
R4
R3
R4
R4
R3
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

30kW

80
80
80
80
80
80
90
90
90
90
90
90
90
100
100
100
100
112
112
112
112
112
112
112
125
125
125
125
125
125
125
140
140
140
140
140
140
160
160
160
160
180
180
180
180
180
200
200
200
224
224
224
224
250
250
250
250
280
280
280
315
315
315
355
355
400
450

B-44
B-44
B-46
B-50
B-46
B-50
B-48
B-44
B-50
B-46
B-50
B-46
B-50
B-48
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-48
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-54
B-54
B-56
B-60
B-56
B-60
B-58
B-54
B-60
B-56
B-60
B-56
B-60
B-58
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-58
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-64
B-64
B-66
B-70
B-66
B-70
B-68
B-64
B-70
B-66
B-70
B-66
B-70
B-68
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-68
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

B - 31

SELECTION Drive Unit Right Angle Shaft

37kW

Frequency Hz
Pole
P
5RGGFn1 r/min

50Hz
4
1500

60Hz
4
1800

* marked model upright type need additional cooling

system for continuous operation.

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

238
211

1480
1670

152
171

188

1880

192

167

2120

216

150

2360

241

134

2640

269

120
107

2940
3300

301
337

93.8

3770

385

83.3

4240

433

75.0

4710

481

67.0

5280

539

60.0

5890

601

53.6

6600

673

47.6

7420

758

42.3

8360

854

Drive Unit

Dimension Selection
Tables
Tables

B - 32

SF
3.72
3.72
3.35
4.37
3.35
4.37
3.05
3.89
3.05
3.89
3.16
3.16
1.70
2.18
1.70
2.18
1.81
2.56
2.94
4.51
1.81
2.56
2.94
4.51
1.81
2.56
2.94
4.51
1.48
1.82
2.16
2.56
2.94
4.51
1.30
1.82
2.13
2.56
2.94
3.67
4.51
1.13
1.56
1.75
2.27
2.51
2.94
3.67
4.51

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

286
254

1240
1390

126
142

225

1570

160

200

1770

180

180

1960

200

161

2200

224

144
129

2450
2750

251
281

113

3140

321

100

3530

361

90.0

3930

401

80.4

4400

449

72.0

4910

501

64.3

5500

561

57.1

6180

631

50.7

6970

711

37kW

Model
SF

Size

3.72
3.72
3.72
5.24
3.72
5.24
3.45
4.67
3.45
4.67
3.78
3.78
2.02
2.62
2.02
2.62
2.10
2.91
3.32
5.13
2.10
2.91
3.32
5.13
2.10
2.91
3.32
5.13
1.75
2.10
2.59
2.91
3.32
5.13
1.54
2.10
2.45
2.91
3.32
4.18
5.13
1.37
1.87
2.10
2.70
2.83
3.32
4.18
5.13

9040
9040
9040
9045
9040
9045
9040
9045
9040
9045
9045
9045
9040
9045
9040
9045
9040
9050
9060
9070
9040
9050
9060
9070
9040
9050
9060
9070
9040
9045
9050
9055
9060
9070
9040
9045
9050
9055
9065
9070
9075
9040
9045
9050
9055
9060
9065
9070
9075

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3

6.3
7.1
8
8
9
9
10
10
11.2
11.2
12.5
14
16
16
18
18
20
20
20
20
22.4
22.4
22.4
22.4
25
25
25
25
28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5

B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-44
B-44
B-46
B-46
B-44
B-44
B-46
B-46
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-46

Vertical

Upright

B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-54
B-54
B-56
B-56
B-54
B-54
B-56
B-56
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-56

B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-64
B-64
B-66
B-66
B-64
B-64
B-66
B-66
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-66

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

37.5

9420

962

33.3

10600

1080

30.0

11780

1200

26.8

13190

1350

23.8

14840

1520

21.1

16730

1710

18.8

18850

1920

16.7

21200

2160

15.0

23560

2410

13.4

26380

2690

12.0

29450

3010

10.7

32980

3370

SF
1.10
1.30
1.64
2.13
2.51
3.67
0.92
1.21
1.35
1.83
2.18
2.51
3.64
1.15
1.32
1.75
2.00
2.51
2.91
3.67
0.97
1.08
1.40
1.72
2.30
2.89
3.67
1.05
1.40
1.62
2.00
2.37
2.91
0.86
1.13
1.35
1.81
2.27
2.91
1.13
1.62
1.78
2.37
2.70
0.91
1.00
1.43
1.78
2.37
2.70
1.00
1.75
2.67
0.83
1.01
1.45
1.78
2.29
2.70
0.86
1.01
1.35
1.78
2.02
2.70
0.89
1.10
1.56
1.75
2.40

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

45.0

7850

802

40.0

8830

902

36.0

9820

1000

32.1

10990

1120

28.6

12370

1260

25.4

13940

1420

22.5

15700

1600

20.0

17670

1800

18.0

19630

2000

16.1

21990

2240

14.4

24540

2510

12.9

27480

2810

Model
SF

Size

1.35
1.56
1.97
2.45
2.83
4.18
1.11
1.44
1.62
2.21
2.62
2.83
4.18
1.38
1.59
2.10
2.27
2.83
3.32
4.18
1.16
1.29
1.67
2.08
2.75
3.32
4.18
1.27
1.70
1.83
2.27
2.70
3.32
1.05
1.35
1.62
2.17
2.70
3.32
1.37
1.83
2.16
2.70
3.05
1.10
1.21
1.71
2.16
2.70
3.05
1.21
2.10
3.05
1.02
1.21
1.75
2.16
2.75
3.05
1.02
1.21
1.62
2.16
2.43
3.05
1.07
1.35
1.86
2.10
2.89

9040
9045
9050
9055
9060
9070
9040
9045
9050
9055
9060
9065
9070
9045
9050
9055
9060
9065
9070
9075
9045
9050
9055
9060
9065
9070
9075
9050
9055
9060
9065
9070
9075
9050
9055
9060
9065
9070
9075
9055
9065
9070
9075
9080
9055
9060
9065
9070
9075
9080
9060
9070
9080
9060
9065
9070
9075
9080
9085
9060
9065
9070
9075
9080
9085
9065
9070
9075
9080
9085

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R4
R3
R4
R3
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

37kW

40
40
40
40
40
40
45
45
45
45
45
45
45
50
50
50
50
50
50
50
56
56
56
56
56
56
56
63
63
63
63
63
63
71
71
71
71
71
71
80
80
80
80
80
90
90
90
90
90
90
100
100
100
112
112
112
112
112
112
125
125
125
125
125
125
140
140
140
140
140

B-44
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-46
B-50
B-46
B-50
B-44
B-50
B-46
B-50
B-46
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-54
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-56
B-60
B-56
B-60
B-54
B-60
B-56
B-60
B-56
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-64
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-66
B-70
B-66
B-70
B-64
B-70
B-66
B-70
B-66
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

B - 33

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

9.4

37690

3850

8.3

42400

4330

7.5

47110

4810

6.7

52770

5390

6.0

58890

6010

5.4

65960

6730

4.8
4.2

74200
83630

7580
8540

Drive Unit

Dimension Selection
Tables
Tables

45kW

SF
0.92
1.43
1.54
2.13
0.89
1.18
1.40
1.83
0.89
1.32
1.54
0.89
1.16
1.45
0.89
1.02
1.40
0.86
1.21
1.08
0.91

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

11.3

31410

3210

10.0

35340

3610

9.0

39260

4010

8.0

43970

4490

7.2

49080

5010

6.4

54970

5610

5.7
5.1

61840
69690

6310
7110

50Hz
4
1500

Model
SF

Size

1.11
1.70
1.83
2.56
1.05
1.43
1.67
2.21
1.05
1.59
1.83
1.05
1.37
1.75
1.05
1.21
1.67
1.05
1.45
1.29
1.10

9065
9075
9080
9085
9070
9075
9080
9085
9070
9080
9085
9075
9080
9085
9075
9080
9085
9080
9085
9085
9085

60Hz
4
1800

Output Speed
r/min

B - 34

238
211

1800
2030

184
208

188

2290

234

167

2580

263

150

2870

293

134

3210

328

120
107

3580
4010

366
410

93.8

4580

468

83.3

5160

527

75.0

5730

585

67.0

6420

655

60.0

7160

731

SF
3.06
3.06
2.75
3.60
2.75
3.60
2.51
3.20
2.51
3.20
2.60
2.60
1.40
1.80
1.40
1.80
1.48
2.11
2.42
3.71
1.48
2.11
2.42
3.71
1.49
2.11
2.42
3.71

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

286
254

1500
1700

154
173

225

1910

195

200

2150

219

180

2390

244

161

2670

273

144
129

2980
3340

305
341

113

3820

390

100

4300

439

90.0

4780

488

80.4

5350

546

72.0

5970

609

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

160
160
160
160
180
180
180
180
200
200
200
224
224
224
250
250
250
280
280
315
355

B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

* marked model upright type need additional cooling system for

continuous operation.

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

37kW, 45kW

Model
SF

Size

3.06
3.06
3.06
4.31
3.06
4.31
2.84
3.84
2.84
3.84
3.11
3.11
1.66
2.15
1.66
2.15
1.73
2.40
2.73
4.22
1.73
2.40
2.73
4.22
1.73
2.40
2.73
4.22

9040
9040
9040
9045
9040
9045
9040
9045
9040
9045
9045
9045
*9040
9045
*9040
9045
9040
9050
9060
9070
9040
9050
9060
9070
9040
9050
9060
9070

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3

6.3
7.1
8
8
9
9
10
10
11.2
11.2
12.5
14
16
16
18
18
20
20
20
20
22.4
22.4
22.4
22.4
25
25
25
25

B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-44
B-44
B-46
B-46
B-44
B-44
B-46
B-46
B-44
B-44
B-46
B-46

Vertical

Upright

B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-54
B-54
B-56
B-56
B-54
B-54
B-56
B-56
B-54
B-54
B-56
B-56

B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-64
B-64
B-66
B-66
B-64
B-64
B-66
B-66
B-64
B-64
B-66
B-66

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

53.6

8020

819

47.6

9020

921

42.3

10170

1040

37.5

11460

1170

33.3

12890

1320

30.0

14330

1460

26.8

16040

1640

23.8

18050

1840

21.1

20340

2080

18.8

22920

2340

16.7

25790

2630

15.0

28650

2930

13.4

32090

3280

SF
1.22
1.50
1.77
2.11
2.42
3.71
1.50
1.75
2.11
2.42
3.02
3.71
1.28
1.44
1.86
2.06
2.42
3.02
3.71
1.06
1.35
1.75
2.06
3.02
0.99
1.11
1.51
1.80
2.06
3.00
0.95
1.08
1.44
1.64
2.06
2.40
3.02
0.88
1.15
1.42
1.89
2.37
3.02
1.15
1.33
1.64
1.95
2.40
0.93
1.11
1.49
1.86
2.40
0.93
1.33
1.46
1.95
2.22
0.82
1.17
1.46
1.95
2.22
0.82
1.44
2.20
0.83
1.20
1.46
1.88
2.22

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

64.3

6690

683

57.1

7520

768

50.7

8480

865

45.0

9550

975

40.0

10740

1100

36.0

11940

1220

32.1

13370

1370

28. 6

15040

1540

25.4

16950

1730

22.5

19100

1950

20.0

21490

2190

18.0

23880

2440

16.1

26740

2730

Model
SF

Size

1.44
1.73
2.13
2.40
2.73
4.22
1.73
2.02
2.40
2.73
3.44
4.22
1.53
1.73
2.22
2.33
2.73
3.44
4.22
1.28
1.62
2.02
2.33
3.44
1.19
1.33
1.82
2.15
2.33
3.44
1.14
1.31
1.73
1.86
2.33
2.73
3.44
1.06
1.37
1.71
2.26
2.73
3.44
1.40
1.51
1.86
2.22
2.73
1.11
1.33
1.78
2.22
2.73
1.13
1.51
1.77
2.22
2.51
1.00
1.40
1.77
2.22
2.51
1.00
1.73
2.51
1.00
1.44
1.77
2.26
2.51

9040
9045
9050
9055
9060
9070
9045
9050
9055
9065
9070
9075
9045
9050
9055
9060
9065
9070
9075
9045
9050
9055
9060
9070
9045
9050
9055
9060
9065
9070
9045
9050
9055
9060
9065
9070
9075
9050
9055
9060
9065
9070
9075
9055
9060
9065
9070
9075
9055
9060
9065
9070
9075
9055
9065
9070
9075
9080
9060
9065
9070
9075
9080
9060
9070
9080
9065
9070
9075
9080
9085

Page of Dimension Sheet

Assembly Reduction
Ratio Horizontal
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R4
R3
R4
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4

45kW

28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
45
45
45
45
45
45
50
50
50
50
50
50
50
56
56
56
56
56
56
63
63
63
63
63
71
71
71
71
71
80
80
80
80
80
90
90
90
90
90
100
100
100
112
112
112
112
112

B-44
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-44
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-44
B-46
B-46
B-46
B-46
B-44
B-46
B-46
B-46
B-46
B-44
B-46
B-46
B-46
B-46
B-44
B-46
B-50
B-46
B-50
B-50
B-46
B-50
B-46
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-54
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-54
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-54
B-56
B-56
B-56
B-56
B-54
B-56
B-56
B-56
B-56
B-54
B-56
B-56
B-56
B-56
B-54
B-56
B-60
B-56
B-60
B-60
B-56
B-60
B-56
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-64
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-64
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-64
B-66
B-66
B-66
B-66
B-64
B-66
B-66
B-66
B-66
B-64
B-66
B-66
B-66
B-66
B-64
B-66
B-70
B-66
B-70
B-70
B-66
B-70
B-66
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

B - 35

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

Drive Unit

Dimension Selection
Tables
Tables

50Hz
Output Torque (Tout)
Nm
kgf m

12.0

35810

3660

10.7

40110

4100

9.4

45840

4680

8.3

51570

5270

7.5

57300

5850

6.7

64180

6550

6.0

71630

7310

5.4
4.8

80220
90250

8190
9210

55kW

SF
0.83
1.11
1.46
1.66
2.22
0.91
1.28
1.44
1.97
1.17
1.26
1.75
0.97
1.15
1.51
1.08
1.26
0.95
1.20
0.84
1.15
1.00
0.88

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

14.4

29840

3050

12.9

33430

3410

11.3

38200

3900

10.0

42980

4390

9.0

47750

4880

8.0

53480

5460

7.2

59690

6090

6.4
5.7

66850
75210

6830
7680

50Hz
4
1500

Model
SF

Size

1.00
1.33
1.77
2.00
2.51
1.11
1.53
1.73
2.37
1.40
1.51
2.11
1.17
1.37
1.82
1.31
1.51
1.13
1.44
1.00
1.37
1.20
1.06

9065
9070
9075
9080
9085
9070
9075
9080
9085
9075
9080
9085
9075
9080
9085
9080
9085
9080
9085
9080
9085
9085
9085

60Hz
4
1800

Output Speed
r/min

B - 36

238
211

2210
2490

225
254

188

2800

286

167

3150

322

150

3500

358

134

3920

400

120

4380

447

107

4900

501

93.8

5600

572

83.8

6300

644

75.0

7000

715

67.0

7840

801

60.0

8750

894

53.6

9800

1000

SF
2.50
2.50
2.25
2.94
2.25
2.94
2.05
2.61
2.05
2.61
1.47
2.12
1.47
2.12
1.14
1.47
1.47
1.14
1.72
1.98
3.03
1.14
1.72
1.98
3.03
1.72
1.98
3.03
1.72
1.98
3.03

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

286
254

1840
2070

188
212

225

2330

238

200

2630

268

180

2920

298

161

3270

334

144

3650

372

129

4090

417

113

4670

477

100.0

5250

536

90.0

5840

596

80.4

6540

667

72.0

7300

745

64.3

8170

834

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

125
125
125
125
125
140
140
140
140
160
160
160
180
180
180
200
200
224
224
250
250
280
315

B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

* marked model upright type need additional cooling system for

continuous operation.

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

45kW, 55kW

Model
SF

Size

2.50
2.50
2.50
3.52
2.50
3.52
2.32
3.14
2.32
3.14
1.76
2.54
1.76
2.54
1.36
1.76
1.76
1.36
1.96
2.23
3.45
1.36
1.96
2.23
3.45
1.96
2.23
3.45
1.96
2.23
3.45

9040
*9040
*9040
9045
*9040
9045
*9040
9045
*9040
9045
*9040
9045
*9040
9045
*9040
9045
*9045
*9045
9050
9060
9070
*9045
9050
9060
9070
9055
9060
9070
9055
9060
9070

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R2
R3
R3
R3
R2
R3
R3
R3
R3
R3
R3
R3
R3
R3

6.3
7.1
8
8
9
9
10
10
11.2
11.2
12.5
12.5
14
14
16
16
18
20
20
20
20
22.4
22.4
22.4
22.4
25
25
25
28
28
28

B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-42
B-44
B-46
B-46
B-42
B-44
B-46
B-46
B-44
B-46
B-46
B-44
B-46
B-46

Vertical

Upright

B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-52
B-54
B-56
B-56
B-52
B-54
B-56
B-56
B-54
B-56
B-56
B-54
B-56
B-56

B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-62
B-64
B-66
B-66
B-62
B-64
B-66
B-66
B-64
B-66
B-66
B-64
B-66
B-66

SELECTION Drive Unit Right Angle Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

47.6

11030

1130

42.3

12430

1270

37.5

14010

1430

33.3

15760

1610

30.0

17510

1790

26.8

19610

2000

23.8

22060

2250

21.1

24860

2540

18.8

28010

2860

16.7

31520

3220

15.0

35020

3580

13.4

39220

4000

12.0

43770

4470

10.7

49020

5010

9.4

56030

5720

8.3

63030

6440

7.5

70030

7150

6.7
6.0

78440
87540

8010
8940

SF
1.72
1.98
2.47
3.03
1.52
1.69
1.98
2.47
3.03
1.43
1.69
2.47
1.23
1.47
1.69
2.45
1.18
1.34
1.69
1.96
2.47
0.94
1.16
1.55
1.94
2.47
0.94
1.09
1.34
1.60
1.96
0.90
1.22
1.52
1.96
1.09
1.20
1.60
1.81
0.96
1.20
1.60
1.81
1.18
1.80
0.98
1.20
1.54
1.81
0.90
1.20
1.36
1.81
1.05
1.18
1.61
0.96
1.03
1.43
0.94
1.23
0.89
1.03
0.98
0.94

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

57.1

9190

938

50.7

10360

1060

45.0

11670

1190

40.0

13130

1340

36.0

14590

1490

32.1

16340

1670

28.6

18380

1880

25.4

20720

2120

22.5

23340

2380

20.0

26260

2680

18.0

29180

2980

16.1

32680

3340

14.4

36480

3720

12.9

40850

4170

11.3

46690

4770

10.0

52530

5360

9.0

58360

5960

8.0
7.2

65360
72950

6670
7450

Model
SF

Size

1.96
2.23
2.81
3.45
1.81
1.90
2.23
2.81
3.45
1.65
1.90
2.81
1.49
1.76
1.90
2.81
1.41
1.52
1.90
2.23
2.81
1.12
1.40
1.85
2.23
2.81
1.14
1.23
1.52
1.81
2.23
1.09
1.46
1.81
2.23
1.23
1.45
1.81
2.05
1.15
1.45
1.81
2.05
1.41
2.05
1.18
1.45
1.85
2.05
1.09
1.45
1.63
2.05
1.25
1.41
1.94
1.14
1.23
1.72
1.12
1.49
1.07
1.23
1.18
1.12

9055
9065
9070
9075
9055
9060
9065
9070
9075
9055
9060
9070
9055
9060
9065
9070
9055
9060
9065
9070
9075
9055
9060
9065
9070
9075
9055
9060
9065
9070
9075
9060
9065
9070
9075
9065
9070
9075
9080
9065
9070
9075
9080
9070
9080
9070
9075
9080
9085
9070
9075
9080
9085
9075
9080
9085
9075
9080
9085
9080
9085
9080
9085
9085
9085

Page of Dimension Sheet

Assembly Reduction
Horizontal
Ratio
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R3
R4
R3
R4
R3
R4
R3
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4
R4

55kW

31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
40
40
40
45
45
45
45
50
50
50
50
50
56
56
56
56
56
63
63
63
63
63
71
71
71
71
80
80
80
80
90
90
90
90
100
100
112
112
112
112
125
125
125
125
140
140
140
160
160
160
180
180
200
200
224
250

B-44
B-46
B-46
B-46
B-44
B-46
B-46
B-46
B-46
B-44
B-46
B-46
B-44
B-46
B-46
B-46
B-44
B-46
B-46
B-46
B-46
B-44
B-46
B-46
B-46
B-46
B-44
B-46
B-46
B-46
B-46
B-46
B-46
B-46
B-46
B-46
B-50
B-46
B-50
B-46
B-50
B-46
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50
B-50

Vertical

Upright

B-54
B-56
B-56
B-56
B-54
B-56
B-56
B-56
B-56
B-54
B-56
B-56
B-54
B-56
B-56
B-56
B-54
B-56
B-56
B-56
B-56
B-54
B-56
B-56
B-56
B-56
B-54
B-56
B-56
B-56
B-56
B-56
B-56
B-56
B-56
B-56
B-60
B-56
B-60
B-56
B-60
B-56
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60
B-60

B-64
B-66
B-66
B-66
B-64
B-66
B-66
B-66
B-66
B-64
B-66
B-66
B-64
B-66
B-66
B-66
B-64
B-66
B-66
B-66
B-66
B-64
B-66
B-66
B-66
B-66
B-64
B-66
B-66
B-66
B-66
B-66
B-66
B-66
B-66
B-66
B-70
B-66
B-70
B-66
B-70
B-66
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70
B-70

B - 37

SELECTION Drive Unit

Allowable Radial and Axial Loads on Slow Speed Shaft

Allowable Radial Load (kN)

Applicable to congurations: Double Reduction RMR, LML

Triple Reduction RML,LMR/Quadruple Reduction RMR, LML

Sheet 1
L.Speed
Shaft
Speed
r/min
9030

Drive Unit

Dimension Selection
Tables
Tables

250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
100
duty
bearing
63
model
40
25

17.7
20.1
25.0
26.5
26.5
26.5

Size of Reducer
9035
29.4
31.4
35.3
35.3
35.3
35.3

9040
29.9
32.4
38.7
42.2
42.2
42.2

9045
32.4
33.8
39.2
47.1
49.1
49.1

9050
37.8
39.7
47.1
54.9
54.9
54.9

9055
46.6
48.1
53.5
62.3
67.7
67.7

9060
39.7
41.7
47.6
58.9
71.1
81.4
71.1
78.0
81.4
81.4
81.4
81.4

9065
49.1
50.5
54.4
64.3
78.0
95.2
93.7
94.7
98.1
98.1
98.1
98.1

9070
44.1
46.1
54.4
65.2
79.0
99.1
70.1
77.5
92.2
114.8
117.7
117.7

250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
100
duty
bearing
63
model
40
25

9.8
12.3
16.7
21.6
26.5
26.5

9080
77.0
89.0
99.0
131.5
141.0
139.5
122.5
137.5
149.5
149.0
148.5
147.0

9085
100.1
108.9
122.1
125.6
125.1
122.6
141.8
132.4
127.0
125.6
125.1
122.6

Applicable to congurations: Double Reduction RML, LMR

Triple Reduction RMR, LML/Quadruple Reduction RML, LMR

Sheet 2
L.Speed
Shaft
Speed
r/min
9030

9075
77.0
89.0
99.0
131.5
141.0
139.5
122.5
137.5
149.5
149.0
148.5
147.0

Size of Reducer
9035
21.6
23.1
29.4
35.3
35.3
35.3

9040
19.1
20.6
26.0
32.9
41.7
42.2

9045
21.6
23.1
27.5
35.3
43.7
49.1

9050
22.6
24.0
28.4
37.3
48.6
54.9

9055
31.4
31.4
35.3
42.7
55.4
67.7

9060
16.7
18.1
22.1
33.4
45.1
60.8
46.1
52.0
60.3
81.4
81.4
81.4

9065
28.4
27.0
30.4
38.3
51.5
68.7
74.6
72.1
79.0
96.6
98.1
98.1

9070
17.2
17.7
25.5
33.8
47.6
67.7
40.2
45.6
59.4
80.0
108.9
117.7

9075
44.0
55.5
63.5
95.0
129.0
167.0
90.0
103.5
116.0
152.5
192.0
180.5

9080
44.0
55.5
63.5
95.0
129.0
167.0
90.0
103.5
116.0
152.5
192.0
180.5

9085
58.4
64.3
74.6
104.5
146.7
171.2
114.8
125.1
140.8
174.1
191.8
171.2

9075
28.0
28.4
39.7
52.5
61.4
61.4
18.6
21.1
27.5
36.3
49.1
56.9

9080
23.5
27.5
32.9
45.6
63.3
67.7
56.9
56.9
56.9
56.9
56.9
56.9

9085
23.5
27.5
32.9
45.6
60.3
60.3
56.9
56.9
56.9
56.9
56.9
56.9

Allowable Axial Load (kN)

L.Speed
Shaft
Speed
r/min
9030

250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
100
duty
bearing
63
model
40
25

B - 38

14.7
18.1
24.5
26.5
26.5
26.5

Size of Reducer
9035
23.1
23.1
23.1
23.1
23.1
23.1

9040
26.5
28.4
32.9
32.9
32.9
32.9

9045
31.4
31.4
31.4
31.4
31.4
31.4

9050
32.9
33.4
37.3
37.3
37.3
37.3

9055
31.9
31.9
31.9
31.9
31.9
31.9

9060
27.0
28.9
34.3
49.1
49.1
49.1
23.1
25.0
29.4
39.2
39.2
39.2

9065
43.2
43.2
43.2
43.2
43.2
43.2
34.8
33.4
36.8
43.2
43.2
43.2

9070
28.0
28.4
39.7
52.5
61.4
61.4
18.6
21.1
27.5
36.3
49.1
56.9

SELECTION Drive Unit

Allowable Radial and Axial Loads on Slow Speed Shaft

Overhang Factor
Overhang Member
Sprocket (Single Row)
Sprocket (Double Row)
Gears

Overhang Factor
1
1.25
1.25

Notes
1. The value shown in the table is allowable radial
load when it is applied to the center of the solid
shaft (except hollow shaft).
Consult us when a load is not in the center.
2. Consult us for the blanks in the table.
3. Consult us when the radial load is applied
upward.
4. In case of double projection shaft (RMB,LMB)
(1) See sheet1 when the radial load is applied
only to the shaft1.
(2) See sheet2 when the radial load is applied
only to the shaft2.
(3) Consult us when the radial load is applied to
both shafts.
5. Refer to B-6 to check overhang load, and
calculate equivalent load at peak load value.
Be careful under following condition because
large peak load may be generated.
Application: When the inertia is large, such as
for crane driving, slewing, etc.
Motor: inline motor
Connecting method: Sprocket or gear
Consult us when the peak load is larger than
allowable value.

RMB
Double
Reduction
Ratio

LMB
2

1
1

2
Triple
Reduction
Ratio

Quadruple
Reduction
Ratio

B - 39

SELECTION Drive Unit

Allowable Radial and Axial Loads on Slow Speed Shaft

Allowable Radial Load (kgf)

Applicable to congurations: Double Reduction RMR, LML

Triple Reduction RML,LMR/Quadruple Reduction RMR, LML

Sheet 1
L.Speed
Shaft
Speed
r/min
9030

Drive Unit

Dimension Selection
Tables
Tables

250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
100
duty
bearing
63
model
40
25

1800
2050
2550
2700
2700
2700

Size of Reducer
9035
3000
3200
3600
3600
3600
3600

9040
3050
3300
3950
4300
4300
4300

9045
3300
3450
4000
4800
5000
5000

9050
3850
4050
4800
5600
5600
5600

9055
4750
4900
5450
6350
6900
6900

9060
4050
4250
4850
6000
7250
8300
7250
7950
8300
8300
8300
8300

9065
5000
5150
5550
6550
7950
9700
9550
9650
10000
10000
10000
10000

Sheet 2
L.Speed
Shaft
Speed
r/min
9030

250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
100
duty
bearing
63
model
40
25

1000
1250
1700
2200
2700
2700

9070
4500
4700
5550
6650
8050
10100
7150
7900
9400
11700
12000
12000

9075
7850
9050
10100
13400
14350
14200
12500
14000
15250
15200
15150
15000

9080
7850
9050
10100
13400
14350
14200
12500
14000
15250
15200
15150
15000

9085
10200
11100
12450
12800
12750
12500
14450
13500
12950
12800
12750
12500

Applicable to congurations: Double Reduction RML, LMR

Triple Reduction RMR, LML/Quadruple Reduction RML, LMR

Size of Reducer
9035
2200
2350
3000
3600
3600
3600

9040
1950
2100
2650
3350
4250
4300

9045
2200
2350
2800
3600
4450
5000

9050
2300
2450
2900
3800
4950
5600

9055
3200
3200
3600
4350
5650
6900

9060 9065 9070

1700 2900 1750
1850 2750 1800
2250 3100 2600
3400 3900 3450
4600 5250 4850
6200 7000 6900
4700 7600 4100
5300 7350 4650
6150 8050 6050
8300 9850 8150
8300 10000 11100
8300 10000 12000

9075
4500
5650
6450
9700
13150
17000
9150
10550
11800
15550
19550
18400

9080
4500
5650
6450
9700
13150
17000
9150
10550
11800
15550
19550
18400

9085
5950
6550
7600
10650
14950
17450
11700
12750
14350
17750
19550
17450

9075
2850
2900
4050
5350
6260
6260
1900
2150
2800
3700
5000
5800

9080
2400
2800
3350
4650
6450
6900
5800
5800
5800
5800
5800
5800

9085
2400
2800
3350
4650
6150
6150
5800
5800
5800
5800
5800
5800

Allowable Axial Load (kgf)

L.Speed
Shaft
Speed
r/min
9030

250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
100
duty
bearing
63
model
40
25

B - 40

1500
1850
2500
2700
2700
2700

Size of Reducer
9035
2350
2350
2350
2350
2350
2350

9040
2700
2900
3350
3350
3350
3350

9045
3200
3200
3200
3200
3200
3200

9050
3350
3400
3800
3800
3800
3800

9055
3250
3250
3250
3250
3250
3250

9060
2750
2950
3500
5000
5000
5000
2350
2550
3000
4000
4000
4000

9065
4400
4400
4400
4400
4400
4400
3550
3400
3750
4400
4400
4400

9070
2850
2900
4050
5350
6260
6260
1900
2150
2800
3700
5000
5800

SELECTION Drive Unit

Allowable Radial and Axial Loads on Slow Speed Shaft

Overhang Factor
Overhang Member
Sprocket (Single Row)
Sprocket (Double Row)
Gears

Overhang Factor
1
1.25
1.25

Notes
1. The value shown in the table is allowable radial
load when it is applied to the center of the solid
shaft (except hollow shaft).
Consult us when a load is not in the center.
2. Consult us for the blanks in the table.
3. Consult us when the radial load is applied
upward.
4. In case of double projection shaft (RMB,LMB)
(1) See sheet1 when the radial load is applied
only to the shaft1.
(2) See sheet2 when the radial load is applied
only to the shaft2.
(3) Consult us when the radial load is applied to
both shafts.
5. Refer to B-6 to check overhang load, and
calculate equivalent load at peak load value.
Be careful under following condition because
large peak load may be generated.
Application: When the inertia is large, such as
for crane driving, slewing, etc.
Motor: inline motor
Connecting method: Sprocket or gear
Consult us when the peak load is larger than
allowable value.

RMB
Double
Reduction
Ratio

LMB
2

1
1

2
Triple
Reduction
Ratio

Quadruple
Reduction
Ratio

B - 41

DIMENSIONS Right Angle Double Reduction Horizontal Mounting

A

MA
MC

9030 9045

E2

MB

MD

DP1

[Fig. 1] Location of oil ll and air vent for

Size 9030 with reduction ratio 6.3 or 7.1

DP1

FY
Drive Unit

Dimension Selection
Tables
Tables

F
E1

H
L

4- J
K

O
P

DP2

D
G

Y
L

*Location of oil ll and air vent

changes for Size 9030 with reduction

ratio 6.3 or 7.1. Refer to Fig. 1.

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 42

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Double Reduction Horizontal Mounting

9030

9045

E1

E2

FY

200

110

160

320

353

349

154

90

28

24

120

590

215

265

410

219

129

185

370

399

154

90

28

24

120

640

215

265

460

235

120

200

400

431

172

115

30

28

150

685

255

315

455

256

141

220

440

471

172

115

30

28

150

745

255

315

515

(L)

5.5-30kW

37-55kW

9030

3/4"

3/4"

10

240

255

9035

3/4"

3/4"

12

260

275

9040

1"

1"

16

340

350

9045

1"

1"

18

400

410

9030
9045

DP1 DP2

With
Btake

11

76

96

634

11

131

175

664

33

213

258

625

664

33

213

258

297

625

664

33

224

280

450

297

625

664

15

259

320

450

297

625

664

15

259

320

412

625

664

29

276

9030

9035

350

188

540

571

324

350

232

540

571

595

394

400

297

601

625

835

394

400

297

601

400

835

394

400

394

450

930.5

394

715.5

394

450

930.5

394

769.5

484

550

MB

MC

MA

MB

MC

11

480

251

350

575

251

15

545

324

350

700

18.5

625

394

400

835

22

625

394

400

30

625

394

37

715.5

45
55

T1

U1

V1

W1/Depth

9030

330

160

170

80m6

9035

330

160

170

90m6

9040

349

179

170

9045

391

181

210

9040

9045

Hollow Shaft (Shrink Disk Type)

Solid Shaft
TU1

Mass of Motor [kg]

Without
Brake

MD

MA

Size

Mass of Motor
Mounting
Flange [kg]

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

150

393

233

160

83

80

330

165

165

75

75

150

403

243

160

88

85

330

165

165

85

85

14

150

448

268

180

98

95

360

180

180

90

90

16

190

463

283

180

108

105

370

185

185

105

105

X1

Y1

Z1

L1

M20/42

22

14

M20/42

25

14

95m6

M24/50

25

105m6

M24/50

28

10

With Brake

Without Brake

Double
Reduction

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Right Angle

*)

Motor
kW

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P H A

Low Speed
Shaft
Type

R 2 9030
9035
9040
9045

Wt.[kg]*

Oil Qty.

Size

9040

See
below

Horizontal Monoblock

9035

PARAMAX

Size

9030 9045

Nominal
Reduction Ratio

Size

RML
RMR
RMB
LMR
LML
LMB

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9030

Nominal Reduction Ratio

6.3

7.1

10

14

16

18

9035
9040
9045

11.2 12.5

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 43

DIMENSIONS Right Angle Triple Reduction Horizontal Mounting

A

MA

BH

MB

MD

MC

9030 9055

BD

DP1
Drive Unit

Dimension Selection
Tables
Tables

F
E1

H
L

4- J
K

O
P

DP2

D
G

Y
L

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 44

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Triple Reduction Horizontal Mounting

E1

9030

200

110

160

320

349

90

28

24

120

590

215

265

410

9035

219

129

185

370

399

90

28

24

120

640

215

265

460

235

120

200

400

431

115

30

28

150

685

255

315

455

256

141

220

440

471

115

30

28

150

745

255

315

515

9045

See
below

255 138.5 210

420

451 116.5

32

28

150

775

285

345

542

9055

286

490

521

32

28

150

845

285

345

615

BD

BH

245

Wt. [kg]*

Oil Qty.

DP1 DP2

115

240

250

9035

3/4"

3/4"

12

260

270

9040

1"

1"

16

325

345

9045

1"

1"

18

385

405

9050

150

263

1"

1"

21

475

485

9055

150

263

1"

1"

28

535

545

*)

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Motor
kW

Without Brake

With Brake

With
Brake

43

54

57

77

714

11

76

96

675

714

11

131

175

664

705

744

33

213

258

625

664

705

744

33

213

258

625

664

705

744

33

224

280

297

625

664

705

744

15

259

320

297

625

664

705

744

15

259

320

705

744

29

276

9030

9035

9040

9045

9050

9055

315

144

540

571

595

634

315

185

540

571

595

634

675

714

251

350

188

540

571

595

634

675

700

324

350

232

540

571

595

634

400

835

394

400

297

601

625

394

400

835

394

394

400

835

394

400

297

601

400

297

715.5

394

450

930.5

394

450

45

715.5

394

450

930.5

394

450

55

769.5

484

550

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

251

11

480

251

350

575

15

545

324

350

18.5

625

394

22

625

30

625

37

412

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

TU1

T1

U1

V1

W1/Depth

9030

330

160

170

80m6

9035

330

160

170

90m6

9040

349

179

170

9045

391

181

9050

411

9055

411

Mass of Motor [kg]

Mass of Motor
Mounting
Flange [kg]

Without
Brake

MD

MA

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

150

393

233

160

83

80

330

165

165

75

75

150

403

243

160

88

85

330

165

165

85

85

14

150

448

268

180

98

95

360

180

180

90

90

10

16

190

463

283

180

108

105

370

185

185

105

105

28

10

16

190

503

303

200

108

105

410

205

205

105

105

32

11

18

185

528

323

205

123

120

410

205

205

115

115

X1

Y1

Z1

L1

M20/42

22

14

M20/42

25

14

95m6

M24/50

25

210

105m6

M24/50

28

201

210

110m6

M24/50

201

210

120m6

M24/50

10

37-55kW

3/4"

Triple
Reduction

5.5-30kW

3/4"

Right Angle

(L)

9030

9030
9055

Size

171

Unit: mm

Nomenclature
Size

P H A

Shaft
Arrangement

Low Speed
Shaft
Option
Type

R 3 9030
9035
9040
9045
9050
9055

Nominal
Reduction Ratio

(blank) : Without Option

B : With Backstop

RML
RMR
RMB
LMR
LML
LMB

Size
9030

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9035

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9040
9045
9050
9055

80

90

H
L

Air Breather

Air Vent

9050

Horizontal Monoblock

9040

PARAMAX

Size

9030 9055

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 45

DIMENSIONS Right Angle Triple Reduction Horizontal Mounting

MA

BD

E2

BH

MB

MD

MC

9060 9075

Drive Unit

F
E1

Dimension Selection
Tables
Tables

4- J
K

K
O
P

DP

D
Y
L

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 46

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Triple Reduction Horizontal Mounting

F

9060

299

151

265

530

158

578

135

35

35

180

885

310

380

615

9065

338

190

300

600

123

648

135

35

35

180

970

310

380

700

336

163

300

600

183

648

160

40

42

215

1020

350

430

700

383

210

335

670

148

718

160

52

42

220

1120

350

430

800

See
below

9075

Wt. [kg]*

Oil Qty.

BD

BH

DP

(L)

5.5-30kW

37-55kW

9060

175

308

1"

29

680

690

9065

175

308

1"

33

805

815

9070

190

330

1"

45

950

960

9075

190

330

1"

52

1200

1210

9060
9075

Size

MD

9060

9065

350

188

744

790

MA

MB

MC

MA

MB

MC

11

480

251

350

575

251

9070

Mass of Motor
Mounting
Flange [kg]

9075

Mass of Motor [kg]

Without
Brake

With
Brake

76

96

11

15

545

324

350

700

324

350

232

744

790

11

131

175

18.5

625

394

400

835

394

400

297

774

820

882

935

33

213

258

22

625

394

400

835

394

400

297

774

820

882

935

33

213

258

30

625

394

400

835

394

400

297

774

820

882

935

33

224

280

37

715.5

394

450

930.5

394

450

297

774

820

882

935

15

259

320

45

715.5

394

450

930.5

394

450

297

774

820

882

935

15

259

320

55

769.5

484

550

412

774

820

882

935

29

276

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

TU1

T1

U1

V1

W1/Depth

9060

440

230

210

125m6

9065

484

234

250

140m6

9070

509

259

250

9075

562

262

300

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

185

583

353

230

128

125

470

235

235

125

123

225

594

359

235

143

140

480

240

240

145

143

20

225

644

384

260

148

145

530

265

265

145

143

22

275

651

386

265

158

155

530

265

265

150

148

X1

Y1

Z1

L1

M24/50

32

11

18

M30/60

36

12

20

145m6

M30/60

36

12

160m6

M30/60

40

13

With Brake

Without Brake

Triple
Reduction

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Right Angle

*)

Motor
kW

E2

E1

Split

Horizontal

9070

PARAMAX

Size

9060 9075

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P H D

R 3 -

9060
9065
9070
9075

Low Speed
Shaft
Option
Type

Nominal
Reduction Ratio

(blank) : Without Option

B : With Backstop

RML
RMR
RMB
LMR
LML
LMB

Size
9060

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 47

DIMENSIONS Right Angle Quadruple Reduction Horizontal Mounting

A

MA

BH

MB

MD

MC

9040 9055

BD

DP1
Drive Unit
H
L

F
E1

Dimension Selection
Tables
Tables

4- J
K

K
D
O
P

DP2

Y
L

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 48

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Quadruple Reduction Horizontal Mounting

E

E1

9040

235

120

200

400

431

115

30

28

150

759

255

315

529

9045

256

141

220

440

471

115

30

28

150

819

255

315

589

9055

BD

420

451 116.5

32

28

150

848

285

345

615

286

490

521

32

28

150

918

285

345

688

BH

171

245

1"

9045

1"

(L)

5.5-30kW

37-55kW

19

355

365

21

425

435

263

1"

1"

24

490

500

9055

150

263

1"

1"

29

550

560

*)

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Motor

A
MD

9040

9045

9050

9055

Mass of Motor
Mounting
Flange [kg]

315

144

674

713

743

782

251

315

185

674

713

743

251

350

188

674

713

743

700

324

350

232

674

713

400

835

394

400

297

704

400

835

394

400

297

704

400

835

394

400

297

Without Brake

With Brake

MA

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

11

480

251

350

575

15

545

324

350

18.5

625

394

22

625

394

30

625

394

Without
Brake

With
Brake

43

54

782

57

77

782

11

76

96

743

782

11

131

175

743

773

812

33

213

258

743

773

812

33

213

258

773

812

33

224

280

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

Mass of Motor [kg]

Key

Hollow Shaft (Key Type)

V1

W1/Depth

170

95m6

M24/50

25

14

150

448

268

180

98

95

360

180

180

90

90

210

105m6

M24/50

28

10

16

190

463

283

180

108

105

370

185

185

105

105

201

210

110m6

M24/50

28

10

16

190

503

303

200

108

105

410

205

205

105

105

201

210

120m6

M24/50

32

11

18

185

528

323

205

123

120

410

205

205

115

115

TU1

T1

U1

9040

349

179

9045

391

181

9050

411

9055

411

X1

Y1

Z1

TU2

L1

T2

U2

V2

V3

TU4

T4

U4

V4

V5

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P H A

Low Speed
Shaft
Type Option

R 4 9040
9045
9050
9055

Nominal
Reduction Ratio

RML
RMR
RMB
LMR
LML
LMB

(blank) : Without Option

B : With Backstop

Size
9040

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9045
9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 49

kW

1"

150

Right Angle Quadruple

Reduction

1"

9050

9040
9055

9040

Wt. [kg]*

Oil Qty.

DP1 DP2

115

Size

255 138.5 210

See
below

Horizontal Monoblock

9050

PARAMAX

Size

9040 9055

DIMENSIONS Right Angle Quadruple Reduction Horizontal Mounting

A

MA

BD

Drive Unit

Dimension Selection
Tables
Tables

E1

E2

BH

MB

MD

MC

9060 9085

4- J
K

K
D

O
P

DP

Y
L

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 50

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Quadruple Reduction Horizontal Mounting

F

9060

299

151

265

530

121

578

135

35

35

9065

338

190

300

600

86

648

135

35

35

336

163

300

600

140

648

160

40

383

210

335

670

105

718

160

52

9080

378

205

335

670

162

718

160

9085

422

249

375

750

122

798

160

9075

See
below

9060

175

308

9065

175

308

9070

190

9075

190

9080
9085

180

970

310

380

700

180

1055

310

380

785

42

215

1115

350

430

795

42

220

1215

350

430

895

52

42

220

1275

380

460

955

52

42

220

1375

380

460

1055

Wt. [kg]*

Oil Qty.
(L)

5.5-30kW

37-55kW

1"

38

700

710

1"

43

855

865

330

1"

57

990

1000

330

1"

67

1210

1220

210

365

1"

73

1410

1420

210

365

1"

90

1670

1680

*)

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Motor
kW

Without Brake

With Brake

MD

9060

9065

9070

9075

9080

9085

315

144

829

875

947

1000

1055

1111

43

54

315

185

829

875

947

1000

1055

1111

57

77

251

350

188

829

875

947

1000

1055

1111

11

76

96

324

350

232

829

875

947

1000

1055

1111

11

131

175

835

394

400

297

859

905

977

1030

1085

1141

33

213

258

835

394

400

297

859

905

977

1030

1085

1141

33

213

258

400

835

394

400

297

859

905

977

1030

1085

1141

33

224

280

394

450

930.5

394

450

297

859

905

977

1030

1085

1141

15

259

320

715.5

394

450

930.5

394

450

297

859

905

977

1030

1085

1141

15

259

320

769.5

484

550

977

1030

1085

1141

29

276

MA

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

251

11

480

251

350

575

15

545

324

350

700

18.5

625

394

400

22

625

394

400

30

625

394

37

715.5

45
55

412
Solid Shaft

Size

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

TU1

T1

U1

V1

W1/Depth

9060

440

230

210

125m6

9065

484

234

250

140m6

9070

509

259

250

9075

562

262

9080

582

9085

585

Hollow Shaft (Shrink Disk Type)

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

185

583

353

230

128

125

470

235

235

125

123

225

594

359

235

143

140

480

240

240

145

143

20

225

644

384

260

148

145

530

265

265

145

143

13

22

275

651

386

265

158

155

530

265

265

150

148

40

13

22

275

714

429

285

173

170

570

285

285

165

163

45

15

25

270

714

429

285

183

180

570

285

285

175

173

X1

Y1

Z1

L1

M24/50

32

11

18

M30/60

36

12

20

145m6

M30/60

36

12

300

160m6

M30/60

40

282

300

165m6

M30/60

285

300

175m6

M30/60

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P H D

Low Speed
Shaft
Type

R 4 9060
9065
9070
9075
9080
9085

Nominal
Reduction Ratio

Option

RML
RMR
RMB
LMR
LML
LMB

(blank) : Without Option

B : With Backstop

Size

Nominal Reduction Ratio

80

9060

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

90 100 112 125 140 160 180 200 224 250 260 280 315 355 400 450

9065
9070

9075
9080
9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 51

DP

BH

Right Angle Quadruple

Reduction

BD

9060
9085

Size

E2

E1

Split

Horizontal

9070

PARAMAX

Size

9060 9085

DIMENSIONS Right Angle Double Reduction Vertical Mounting

MA

A
MC

9030 9045

NP

E3

N2

N1

MB

H
L

E2

C1
Drive Unit

DP1

RI

MD

E1
O

Dimension Selection
Tables
Tables

K
G

K
D

4- J
G

DP2

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

V2

Refer to the Page D-18 for details.

Standard Shaft Arrangement Conguration

RML

U4

T4

Z1

Y1

X1

W1

RMR

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 52

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Double Reduction Vertical Mounting

J

9030

200 155 175 320 220 160

25

50

105

24

120 590

9035

219 186 194 370 245 185

25

50

120

24

235 180 205 400 260 200

30

60

120

28

150 685 100 241.5

256 219 266 440 266 220

30

60

140

28

150 745 120 241.5 17.5

9035

3/4"

9040

1"

9045

1"

N2

85

224

22

117 270 132.5 365

120 640 100

224

22

117 320 132.5 396

15

NP

117 340 157.5 420

117 380 157.5 459

5.5-30kW

37-55kW

240

255

3/4"

260

275

1"

19

340

350

1"

23

400

410

9030
9045

(L)

*)

Without Brake

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

With Brake

MD

9030

9035

350

188

540

571

324

350

232

540

571

595

394

400

297

601

625

835

394

400

297

601

400

835

394

400

394

450

930.5

394

715.5

394

450

930.5

394

769.5

484

550

MA

MB

MC

MA

MB

MC

11

480

251

350

575

251

15

545

324

350

700

18.5

625

394

400

835

22

625

394

400

30

625

394

37

715.5

45
55

TU1

T1

U1

V1

W1/Depth

9030

330

160

170

80m6

9035

330

160

170

90m6

9040

349

179

170

9045

391

181

210

9040

9045

11

76

96

634

11

131

175

664

33

213

258

625

664

33

213

258

297

625

664

33

224

280

450

297

625

664

15

259

320

450

297

625

664

15

259

320

412

625

664

29

276

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

N1

Wt. [kg]*

Oil Qty.

Motor
kW

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

150

393

233

160

83

80

330

165

165

75

75

150

403

243

160

88

85

330

165

165

85

85

14

150

448

268

180

98

95

360

180

180

90

90

16

190

463

283

180

108

105

370

185

185

105

105

X1

Y1

Z1

L1

M20/42

22

14

M20/42

25

14

95m6

M24/50

25

105m6

M24/50

28

10

3/4"

3/4"

Double
Reduction

9030

Right Angle

DP1 DP2

E2

RI

Size

E1

9045

See
below

C1

Monoblock

Vertical

E3

9040

PARAMAX

Size

9030 9045

Unit: mm

Nomenclature

Shaft
Arrangement

Size

P V A

Low Speed
Shaft
Type

R 2 9030
9035
9040
9045

Nominal
Reduction Ratio

RML
RMR

Size

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9030

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9035
9040
9045

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 53

DIMENSIONS Right Angle Triple Reduction Vertical Mounting

A

9030 9055

MA

E3

N2

N1

MB

MC

H
L

NP

E2

C1
Drive Unit

DP2

RI

MD

Dimension Selection
Tables
Tables

E1
O

DP1

K
G

K
Y

4- J
G

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

V2

Refer to the Page D-18 for details.

Standard Shaft Arrangement Conguration

RML

U4

T4

Z1

Y1

X1

W1

RMR

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 54

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Triple Reduction Vertical Mounting

E2

RI

N1

N2

9030

200 264 175 320 220 160

25

50

105

24

120 590

9035

219 295 194 370 245 185

25

50

120

24

235 306 205 400 260 200

30

60

120

28

150 685 100 237.5 15

117 340 157.5 420

256 345 226 440 266 220

30

60

140

28

150 745 120 237.5 17.5

117 380 157.5 459

9050

255 358 225 420 270 210

30

60

140

28

150 775 110 257.5 23

117 360 172.5 490

9055

286 397 256 490 305 245

30

60

155

28

150 845 135 257.5 23

117 430 172.5 529

85

211

22

100 270 132.5 365

120 640 100

211

22

100 320 132.5 396

9030

3/4"

3/4"

240

250

9035

3/4"

3/4"

12

260

270

9040

1"

1"

18

325

345

9045

1"

1"

22

385

405

9050

1"

1"

21

475

485

9055

1"

1"

30

535

545

(L)

5.5-30kW

9030
9055

DP1 DP2

37-55kW

MD

9030

9035

9040

9045

315

144

540

571

595

634

315

185

540

571

595

251

350

188

540

571

324

350

232

540

571

835

394

400

297

835

394

400

297

400

835

394

400

394

450

930.5

394

715.5

394

450

930.5

394

769.5

484

550

9050

9055

43

54

634

675

714

57

77

595

634

675

714

11

76

96

595

634

675

714

11

131

175

601

625

664

705

744

33

213

258

601

625

664

705

744

33

213

258

297

625

664

705

744

33

224

280

450

297

625

664

705

744

15

259

320

450

297

625

664

705

744

15

259

320

705

744

29

276

MA

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

251

11

480

251

350

575

15

545

324

350

700

18.5

625

394

400

22

625

394

400

30

625

394

37

715.5

45
55

412
Solid Shaft

TU1

T1

U1

V1

W1/Depth

9030

330

160

170

80m6

9035

330

160

170

90m6

9040

349

179

170

9045

391

181

9050

411

9055

411

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

Hollow Shaft (Shrink Disk Type)

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

150

393

233

160

83

80

330

165

165

75

75

150

403

243

160

88

85

330

165

165

85

85

14

150

448

268

180

98

95

360

180

180

90

90

10

16

190

463

283

180

108

105

370

185

185

105

105

28

10

16

190

503

303

200

108

105

410

205

205

105

105

32

11

18

185

528

323

205

123

120

410

205

205

115

115

X1

Y1

Z1

L1

M20/42

22

14

M20/42

25

14

95m6

M24/50

25

210

105m6

M24/50

28

201

210

110m6

M24/50

201

210

120m6

M24/50

With Brake

Without Brake

Triple
Reduction

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Right Angle

*)

Motor

Size

Wt. [kg]*

Oil Qty.

Size

kW

NP

E1

See
below

C1

Monoblock

9045

Vertical

E3

9040

PARAMAX

Size

9030 9055

Unit: mm

Nomenclature

Shaft
Arrangement

Size

P V A

R 3 9030
9035
9040
9045
9050
9055

Low Speed
Shaft
Type

Nominal
Reduction Ratio

RML
RMR

Size

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9030

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9035
9040
9045
9050
9055

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 55

DIMENSIONS Right Angle Triple Reduction Vertical Mounting

MA

E3

N1

P
H

MB

P1

MC

9060 9075

NP

E2

C1
DP1
M

Drive Unit

MD

RI

E1
O

Dimension Selection
Tables
Tables

K
DP2

K
D

4- J
G

* Refer to footnote 3.

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

V2

Refer to the Page D-18 for details.

Standard Shaft Arrangement Conguration

RML

U4

T4

Z1

Y1

X1

W1

RMR

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RMR is equipped with visible gauge. Refer to page D-28.

B - 56

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Triple Reduction Vertical Mounting

E3

RI

9060

299

414

251

530

282

265

35

35

160

35

180

885

9065

338

290

600

317

300

35

35

175

35

180

970

9070

See
below 336

460
482

283

600

317

300

40

40

175

9075

383

535

330

670

352

355

40

52

190

DP1 DP2

(L)

5.5-30kW

37-55kW

N1

NP

P1

140 277.5

35

117

460

190

213

564

175 277.5

38

117

530

190

213

610

42

215 1020 155 302.5

38

117

520

215

233

657

42

220 1120 195 302.5

40

117

590

215

233

710

815

9070

1"

1"

46

950

960

9075

1"

1"

59

1200

1210

*)

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Motor
Without Brake

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

With Brake

MD

9060

9065

350

188

744

790

11

76

96

350

232

744

790

11

131

175

394

400

297

774

820

882

935

33

213

258

835

394

400

297

774

820

882

935

33

213

258

835

394

400

297

774

820

882

935

33

224

280

450

930.5

394

450

297

774

820

882

935

15

259

320

394

450

930.5

394

450

297

774

820

882

935

15

259

320

484

550

412

774

820

882

935

29

276

MA

MB

MC

MA

MB

MC

11

480

251

350

575

251

15

545

324

350

700

324

18.5

625

394

400

835

22

625

394

400

30

625

394

400

37

715.5

394

45

715.5

55

769.5

T1

U1

V1

W1/Depth

9060

440

230

210

125m6

9065

484

234

250

140m6

9070

509

259

250

9075

562

262

300

9075

Hollow Shaft (Shrink Disk Type)

Solid Shaft
TU1

9070

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

185

583

353

230

128

125

470

235

235

125

123

225

594

359

235

143

140

480

240

240

145

143

20

225

644

384

260

148

145

530

265

265

145

143

22

275

651

386

265

158

155

530

265

265

150

148

X1

Y1

Z1

L1

M24/50

32

11

18

M30/60

36

12

20

145m6

M30/60

36

12

160m6

M30/60

40

13

690

805

680

35

Triple
Reduction

28

1"

Right Angle

1"

1"

9060
9075

1"

9065

Size

Wt. [kg]*

Oil Qty.

9060

kW

E2

E1

Split

C1

Vertical

Size

PARAMAX

Size

9060 9075

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P V D

R 3 9060
9065
9070
9075

Low Speed
Shaft
Type

Nominal
Reduction Ratio

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

RML
RMR

Size
9060

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 57

DIMENSIONS Right Angle Quadruple Reduction Vertical Mounting

B

9040 9055

MA
MC

E3

N1

MB

H
L

NP

E2

M2

C1
DP2
M1

Drive Unit

MD

RI

M1

E1
O

Dimension Selection
Tables
Tables

K
DP1

K
Y

4- J
G

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

V2

Refer to the Page D-18 for details.

Standard Shaft Arrangement Conguration

LMR

U4

T4

Z1

Y1

X1

W1

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 58

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Quadruple Reduction Vertical Mounting

E2

RI

9040

235 398 205 400 260 200

30

60

120

9045

30

60

9050

See 256 437 226 440 277 220

below 255 467 225 420 270 210

30

9055

286 506 256 490 305 245

30

M1

M2

N1

NP

(L)

5.5-30kW

37-55kW

28

150 759 100

70

228.5

15

100

340 157.5 494

140

28

150 819 120

90

228.5 17.5 100

380 157.5 533

60

140

28

150 848 110

83

248.5

23

100

360 172.5 563

60

155

28

150 918 135 118 248.5

23

100

430 172.5 602

355

365

22

425

435

9050

1"

1"

24

490

500

9055

1"

1"

34

550

560

*)

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Motor
With Brake

MD

9040

9045

9050

9055

315

144

674

713

743

782

43

54

315

185

674

713

743

782

57

77

251

350

188

674

713

743

782

11

76

96

MA

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

251

11

480

251

350

575

15

545

324

350

700

324

350

232

674

713

743

782

11

131

175

18.5

625

394

400

835

394

400

297

704

743

773

812

33

213

258

22

625

394

400

835

394

400

297

704

743

773

812

33

213

258

30

625

394

400

835

394

400

297

773

812

33

224

280

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Key

W1/Depth

TU1

T1

U1

V1

9040

349

179

170

95m6

M24/50

9045

391

181

210

105m6

M24/50

9050

411

201

210

110m6

M24/50

9055

411

201

210

120m6

M24/50

X1

TU2

T2

U2

150

448

268

180

190

463

283

180

16

190

503

303

200

18

185

528

323

205

Y1

Z1

L1

25

14

28

10

16

28

10

32

11

V2

Hollow Shaft (Key Type)

V3

TU4

T4

U4

V4

V5

98

95

360

180

180

90

90

108

105

370

185

185

105

105

108

105

410

205

205

105

105

123

120

410

205

205

115

115

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P V A

R 4 9040
9045
9050
9055

Low Speed
Shaft
Type

Nominal
Reduction Ratio

LMR
LML

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9040

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9045
9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 59

Without Brake

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

18

1"

Right Angle Quadruple

Reduction

1"

1"

9040
9055

1"

9045

Size

Wt. [kg]*

Oil Qty.

9040

kW

E1

DP1 DP2

C1

Monoblock

Vertical

E3

Size

PARAMAX

Size

9040 9055

DIMENSIONS Right Angle Quadruple Reduction Vertical Mounting

B

9060 9085

MA

E3

N1

P
H

MB

MC

P1

NP

E2

C1
M2

Drive Unit

DP1

RI

M1

MD

E1
O

M1

Dimension Selection
Tables
Tables

*Refer to
footnote 3.

K
G

4- J
G

Y
L

DP2

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

V2

Refer to the Page D-18 for details.

Standard Shaft Arrangement Conguration

LMR

U4

T4

Z1

Y1

X1

W1

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement LMR is equipped with visible gauge. Refer to page D-28.

B - 60

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Quadruple Reduction Vertical Mounting

E2

RI

9060

299 540 251 530 282 265

35

35

160

9065

338 586 290 600 317 300

35

35

175

9070

See 336 630 283 600 317 300

below 383 683 330 670 352 335

40

40

9075

40

52

9080

378 725 325 670 352 335

40

9085

422 781 369 750 392 375

40

NP

N1

P1

35

180 970 140 118 277.5 117

35

460 190 203 649

35

180 1055 175 153 277.5 117

38

530 190 203 695

175

42

215 1115 155 128 302.5 117

38

520 215 233 752

190

42

220 1215 195 163 302.5 117

40

590 215 233 805

52

190

42

220 1275 170 140 322.5 117

45

590 230 263 870

52

215

42

220 1375 210 180 322.5 117

40

670 230 263 926

5.5-30kW

37-55kW

700

710

45

855

865

9070

1"

1"

54

990

1000

9075

1"

1"

68

1210

1220

9080

1"

1"

69

1410

1420

9085

1"

1"

94

1670

1680

*)

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Motor
Without Brake

With Brake

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

MD

9060

9065

9070

9075

9080

9085

315

144

829

875

947

1000

1055

1111

43

54

315

185

829

875

947

1000

1055

1111

57

77

251

350

188

829

875

947

1000

1055

1111

11

76

96

324

350

232

829

875

947

1000

1055

1111

11

131

175

835

394

400

297

859

905

977

1030

1085

1141

33

213

258

835

394

400

297

859

905

977

1030

1085

1141

33

213

258

400

835

394

400

297

859

905

977

1030

1085

1141

33

224

280

394

450

930.5

394

450

297

859

905

977

1030

1085

1141

15

259

320

715.5

394

450

930.5

394

450

297

859

905

320

769.5

484

550

MA

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

251

11

480

251

350

575

15

545

324

350

700

18.5

625

394

400

22

625

394

400

30

625

394

37

715.5

45
55

412

977

1030

1085

1141

15

259

977

1030

1085

1141

29

276

Hollow Shaft (Shrink Disk Type)

Solid Shaft
TU1

T1

U1

V1

W1/Depth

9060

440

230

210

125m6

9065

484

234

250

140m6

9070

509

259

250

9075

562

262

9080

582

9085

585

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

185

583

353

230

128

125

470

235

235

125

123

225

594

359

235

143

140

480

240

240

145

143

20

225

644

384

260

148

145

530

265

265

145

143

13

22

275

651

386

265

158

155

530

265

265

150

148

40

13

22

275

714

429

285

173

170

570

285

285

165

163

45

15

25

270

714

429

285

183

180

570

285

285

175

173

X1

Y1

Z1

L1

M24/50

32

11

18

M30/60

36

12

20

145m6

M30/60

36

12

300

160m6

M30/60

40

282

300

165m6

M30/60

285

300

175m6

M30/60

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P V D

R 4 9060
9065
9070
9075
9080
9085

Low Speed
Shaft
Type

Nominal
Reduction Ratio

LMR
LML

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9060

9065
9070

9075
9080
9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 61

36

1"

1"

1"

Right Angle Quadruple

Reduction

1"

9060
9085

(L)

9065

Size

M2

Wt. [kg]*

Oil Qty.

9060

kW

M1

E1

DP1 DP2

C1

Split

Vertical

E3

Size

PARAMAX

Size

9060 9085

DIMENSIONS Right Angle Double Reduction Upright Mounting

9030 9045

MB

MA

MD

MC

4- J2
K3

DP1

Y4
L

H
L

Y1

Y3

H2

4- J1
K1

K2

K1

K2

DP2

H1
K3

Dimension Selection
Tables
Tables

Drive Unit

Y2
E1
F

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 62

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

E1

H1

H2

J1

J2

9030

200

110

160

320

348

90

60

28

24

24

85

50

120

590

265

215

9035

219

185

370

398

90

60

28

24

24

100

50

120

640

265

215

9040

See
below 235

129
120

200

400

430

115

75

30

28

28

100

60

150

685

315

255

9045

256

141

220

440

470

115

75

30

28

28

120

60

150

745

315

255

Size

DP1 DP2

9030

3/4"

9035

3/4"

9040
9045

K3

Y1

Y3

Y4

200

215

410

250

215

460

260

255

455

300

255

515

5.5-30kW

37-55kW

3/4"

14

240

255

3/4"

19

260

275

1"

1"

24

340

350

1"

1"

30

400

410

9030
9045

(L)

MD

9030

9035

9040

9045

350

188

540

571

350

232

540

11

76

96

571

595

634

11

131

175

394

400

297

601

625

664

33

213

258

835

394

835

394

400

297

601

625

664

33

213

258

400

297

625

664

33

224

280

450

930.5

450

930.5

394

450

297

625

664

15

259

320

394

450

297

625

664

15

259

320

412

625

664

29

276

MC

MA

MB

MC

11

480

251

350

575

251

15

545

324

350

700

324

18.5

625

394

400

835

22

625

394

400

30

625

394

400

37

715.5

394

45

715.5

394

55

769.5

484

550

Hollow Shaft (Shrink Disk Type)

Solid Shaft
TU1

T1

U1

V1

W1/Depth

9030

330

160

170

80m6

9035

330

160

170

90m6

9040

349

179

170

9045

391

181

210

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

150

393

233

160

83

80

330

165

165

75

75

150

403

243

160

88

85

330

165

165

85

85

14

150

448

268

180

98

95

360

180

180

90

90

16

190

463

283

180

108

105

370

185

185

105

105

X1

Y1

Z1

L1

M20/42

22

14

M20/42

25

14

95m6

M24/50

25

105m6

M24/50

28

10

With Brake

MB

Without Brake

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

Double
Reduction

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Right Angle

*)

MA

Size

K2

Wt. [kg]*

Oil Qty.

Motor
kW

K1

Y2

Monoblock

Upright

9030 9045
PARAMAX

Size

DIMENSIONS Right Angle Double Reduction Upright Mounting

Unit: mm

Nomenclature

Shaft
Arrangement

Size

P W A

Low Speed
Shaft
Type

R 2 9030
9035
9040
9045

Nominal
Reduction Ratio

RML
RMR
RMB
LMR
LML
LMB

Size

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9030

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9035
9040
9045

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 63

DIMENSIONS Right Angle Triple Reduction Upright Mounting

9030 9055

MB

MA

MD

MC

4- J2
K3

DP1

H
L

Y1

Y3

H2

4- J1
K1

K2

H1
K3

Dimension Selection
Tables
Tables

Y4
L

Drive Unit

K1

K2

DP2

Y2
E1
F

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 64

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Triple Reduction Upright Mounting

G

H1

H2

J1

J2

K1

K2

K3

Y1

Y2

Y3

Y4

9030

200

110

160

320

348

90

60

28

24

24

85

50

120

590

265

215

200

215

410

9035

219

129

185

370

398

90

60

28

24

24

100

50

120

640

265

215

250

215

460

9040

See 235
below 256

120

200

400

430

115

75

30

28

28

100

60

150

685

315

255

260

255

455

141

220

440

470

115

75

30

28

28

120

60

150

745

315

255

300

255

515

9050

255 138.5 210

420

450 116.5

75

32

28

28

110

60

150

775

345

285

280

285

542

9055

286

490

520

75

32

28

28

135

60

150

845

345

285

350

285

615

Size

DP1 DP2

(L)

5.5-30kW

37-55kW

9030

3/4"

3/4"

16

240

250

9035

3/4"

3/4"

21

260

270

9040

1"

1"

29

325

345

9045

1"

1"

36

385

405

9050

1"

1"

35

475

485

9055

1"

1"

46

535

545

171

245

115

Wt. [kg]*

Oil Qty.

9030
9055

MD

9030

9035

9040

9045

315

144

540

571

595

634

315

185

540

571

595

251

350

188

540

571

540

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

251

11

480

251

350

575

9050

9055

43

54

634

675

714

57

77

595

634

675

714

11

76

96

15

545

324

350

700

324

350

232

571

595

634

675

714

11

131

175

18.5

625

394

400

835

394

400

297

601

625

664

705

744

33

213

258

22

625

394

400

835

394

400

297

601

625

664

705

744

33

213

258

30

625

394

400

835

394

400

297

625

664

705

744

33

224

280

37

715.5

394

450

930.5

394

450

297

625

664

705

744

15

259

320

45

715.5

394

450

930.5

394

450

297

625

664

705

744

15

259

320

55

769.5

484

550

705

744

29

276

412

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

TU1

T1

U1

V1

W1/Depth

9030

330

160

170

80m6

9035

330

160

170

90m6

9040

349

179

170

9045

391

181

9050

411

9055

411

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

150

393

233

160

83

80

330

165

165

75

75

150

403

243

160

88

85

330

165

165

85

85

14

150

448

268

180

98

95

360

180

180

90

90

10

16

190

463

283

180

108

105

370

185

185

105

105

28

10

16

190

503

303

200

108

105

410

205

205

105

105

32

11

18

185

528

323

205

123

120

410

205

205

115

115

X1

Y1

Z1

L1

M20/42

22

14

M20/42

25

14

95m6

M24/50

25

210

105m6

M24/50

28

201

210

110m6

M24/50

201

210

120m6

M24/50

With Brake

MA

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

Without Brake

Triple
Reduction

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Right Angle

*)

Motor
kW

E1

Monoblock

Upright

9045

PARAMAX

Size

9030 9055

Unit: mm

Nomenclature

Shaft
Arrangement

Size

P W A

R 3 9030
9035
9040
9045
9050
9055

Low Speed
Shaft
Type

Nominal
Reduction Ratio

RML
RMR
RMB
LMR
LML
LMB

Size

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9030

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9035
9040
9045
9050
9055

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 65

DIMENSIONS Right Angle Triple Reduction Upright Mounting

9060 9075

MB

MA

MD

MC

DP1

4- J
K

H
L

Drive Unit

Dimension Selection
Tables
Tables

H
P

DP2

E1
F

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 66

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Triple Reduction Upright Mounting

F

9060

299

151

265

530

577

135

35

35

180

885

310

380

615

9065

190

300

600

647

135

35

35

180

975

310

380

700

9070

See 338
below 336

163

300

600

647

160

40

42

215 1020 350

430

700

9075

383

210

355

670

717

160

52

42

220 1120 350

430

800

Size

DP1 DP2

Wt. [kg]*

Oil Qty.
(L)

5.5-30kW

37-55kW

56

680

690

1"

65

805

815

9070

1"

1"

83

950

960

9075

1"

1"

100

1200

1210

*)

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

With Brake

Without Brake

9060

9065

350

188

744

790

11

76

96

350

232

744

790

11

131

175

394

400

297

774

820

882

935

33

213

258

835

394

400

297

774

820

882

935

33

213

258

835

394

400

297

774

820

882

935

33

224

280

450

930.5

394

450

297

774

820

882

935

15

259

320

394

450

930.5

394

450

297

774

820

882

935

15

259

320

484

550

412

774

820

882

935

29

276

MB

MC

MA

MB

MC

11

480

251

350

575

251

15

545

324

350

700

324

18.5

625

394

400

835

22

625

394

400

30

625

394

400

37

715.5

394

45

715.5

55

769.5

9075

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

9070

TU1

T1

U1

V1

W1/Depth

9060

440

230

210

125m6

9065

484

234

250

140m6

9070

509

259

250

9075

562

262

300

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

185

583

353

230

128

125

470

235

235

125

123

225

594

359

235

143

140

480

240

240

145

143

20

225

644

384

260

148

145

530

265

265

145

143

22

275

651

386

265

158

155

530

265

265

150

148

X1

Y1

Z1

L1

M24/50

32

11

18

M30/60

36

12

20

145m6

M30/60

36

12

160m6

M30/60

40

13

Unit: mm

Nomenclature

Shaft
Arrangement

Size

P W D

Low Speed
Shaft
Type

R 3 W 9060
9065
9070
9075

Nominal
Reduction Ratio

RML
RMR
RMB
LMR
LML
LMB

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9060

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 67

MD

MA

kW

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

Triple
Wall Mount
Reduction

Motor

1"

1"

Right Angle

1"

9065

9060
9075

9060

E1

Split

Upright

PARAMAX

Size

9060 9075

DIMENSIONS Right Angle Quadruple Reduction Upright Mounting

9040 9055

MB

MA

MD

MC

Y4
L

H
L

4- J2
K3

DP1

Drive Unit

Y1

Y3

H2

4- J1
K1

K2

H1
K3

Dimension Selection
Tables
Tables

K1

K2

DP2

Y2
E1
F

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 68

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Quadruple Reduction Upright Mounting

F

H1

H2

J1

J2

K1

K2

K3

Y1

Y2

Y3

Y4

9040

235

120

200

400

430

115

75

30

28

28

100

60

150

759

315

255

260

255

529

9045

141

220

440

470

115

75

30

28

28

120

60

150

819

315

255

300

255

589

9050

See 256
below 255

9055

286

Size

DP1 DP2

138.5

210

420

450 116.5

75

32

28

28

110

60

150

848

345

285

280

285

615

171

245

490

520

75

32

28

28

135

60

150

918

345

285

350

285

688

115

Wt. [kg]*

Oil Qty.

5.5-30kW

37-55kW

1"

1"

35

355

365

9045

1"

1"

43

425

435

9050

1"

1"

46

490

500

9055

1"

1"

59

550

560

9040
9055

(L)

9040

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

9040

9045

9050

9055

315

144

674

713

743

782

43

54

315

185

674

713

743

782

57

77

251

350

188

674

713

743

782

11

76

96

700

324

350

232

674

713

743

782

11

131

175

400

835

394

400

297

704

743

773

812

33

213

258

400

835

394

400

297

704

743

773

812

33

213

258

400

835

394

400

297

773

812

33

224

280

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

251

11

480

251

350

575

15

545

324

350

18.5

625

394

22

625

394

30

625

394

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Key

W1/Depth

TU1

T1

U1

V1

9040

349

179

170

95m6

M24/50

9045

391

181

210

105m6

M24/50

9050

411

201

210

110m6

M24/50

9055

411

201

210

120m6

M24/50

X1

TU2

T2

U2

150

448

268

180

190

463

283

180

16

190

503

303

200

18

185

528

323

205

Y1

Z1

L1

25

14

28

10

16

28

10

32

11

V2

Hollow Shaft (Key Type)

V3

TU4

T4

U4

V4

V5

98

95

360

180

180

90

90

108

105

370

185

185

105

105

108

105

410

205

205

105

105

123

120

410

205

205

115

115

Unit: OO

Nomenclature
Size

P W A

Shaft
Arrangement

R 4 9040
9045
9050
9055

Low Speed
Shaft
Type

Nominal
Reduction Ratio

RML
RMR
RMB
LMR
LML
LMB

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9040

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9045
9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 69

MD

MA

Size

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

With Brake

Without Brake

Right Angle Quadruple

Reduction

*)

Motor
kW

E1

Monoblock

Upright

PARAMAX

Size

9040 9055

DIMENSIONS Right Angle Quadruple Reduction Upright Mounting

9060 9085

MB

MA

MD

MC

4- J

DP1

H
L

Drive Unit

Y
L

Dimension Selection
Tables
Tables

H
O

DP2

E1
F

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

U4

V2

X1

Refer to the Page D-18 for details.

W1

Standard Shaft Arrangement Conguration

RML

RMR

RMB

LMR

LML

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.

B - 70

T4

Z1

Y1

TU4
T2

V3

U2

V4

T1

V1

U1
L1

Hollow Shaft (Key Type)

TU2

V5

Solid Shaft

LMB

Refer to the Page D-18 for details.

DIMENSIONS Right Angle Quadruple Reduction Upright Mounting

F

9060

299

151

265

530

577

135

35

35

180

970

310

380

700

9065

338

190

300

600

648

135

35

35

180 1055 310

380

785

9070

See 336
below 383

163

300

600

648

160

40

42

215 1115 350

430

795

9075

210

335

670

717

160

52

42

220 1215 350

430

895

9080

378

205

335

670

717

160

52

42

220 1275 380

460

955

9085

422

249

375

750

797

160

52

42

220 1375 380

460 1055

Size

DP1 DP2

Wt. [kg]*

Oil Qty.

5.5-30kW

37-55kW

700

710

9065

1"

1"

85

855

865

9070

1"

1"

107

990

1000

9075

1"

1"

122

1210

1220

9080

1"

1"

128

1410

1420

9085

1"

1"

174

1670

1680

*)

Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Motor
Without Brake

A
Brake

MD

9060

9065

9070

9075

9080

9085

315

144

829

875

947

1000

1055

1111

43

54

315

185

829

875

947

1000

1055

1111

57

77

251

350

188

829

875

947

1000

1055

1111

11

76

96

MA

MB

MC

MA

MB

MC

5.5

382

212

315

454

212

7.5

415

251

315

510

251

11

480

251

350

575

15

545

324

350

700

324

350

232

829

875

947

1000

1055

1111

11

131

175

18.5

625

394

400

835

394

400

297

859

905

977

1030

1085

1141

33

213

258

22

625

394

400

835

394

400

297

859

905

977

1030

1085

1141

33

213

258

30

625

394

400

835

394

400

297

859

905

977

1030

1085

1141

33

224

280

37

715.5

394

450

930.5

394

450

297

859

905

977

1030

1085

1141

15

259

320

45

715.5

394

450

930.5

394

450

297

859

905

977

1030

1085

1141

15

259

320

55

769.5

484

550

977

1030

1085

1141

29

276

412

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

TU1

T1

U1

V1

W1/Depth

9060

440

230

210

125m6

9065

484

234

250

140m6

9070

509

259

250

9075

562

262

9080

582

9085

585

Key

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

185

583

353

230

128

125

470

235

235

125

123

225

594

359

235

143

140

480

240

240

145

143

20

225

644

384

260

148

145

530

265

265

145

143

13

22

275

651

386

265

158

155

530

265

265

150

148

40

13

22

275

714

429

285

173

170

570

285

285

165

163

45

15

25

270

714

429

285

183

180

570

285

285

175

173

X1

Y1

Z1

L1

M24/50

32

11

18

M30/60

36

12

20

145m6

M30/60

36

12

300

160m6

M30/60

40

282

300

165m6

M30/60

285

300

175m6

M30/60

Unit: mm

Nomenclature
Size

P W D

Shaft
Arrangement

R 4 W 9060
9065
9070
9075
9080
9085

Low Speed
Shaft
Type

Nominal
Reduction Ratio

RML
RMR
RMB
LMR
LML
LMB

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9060

9065
9070

9075
9080
9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 71

Mass of Motor [kg]

Mass of Motor
Mounting
Without With
Flange [kg]
Brake Brake

68

1"

Right Angle Quadruple Wall Mount

Reduction

1"

9060
9085

(L)

9060

kW

E1

Split

Upright

PARAMAX

Size

9060 9085

memo

B - 72

B
<Drive Unit Parallel Shaft Vertical Mounting>

Drive Unit: Parallel Shaft

Selection Tables
B- 74
Allowable Radial
and Axial Loads B- 98
Dimension Tables
B-102
Actual Reduction Ratio B-111

B - 73

SELECTION Drive Unit Parallel Shaft

Shaft Position

High Speed Shaft Speed Ambient Temperature

Parallel Shaft

kW

5.5kW
4P

7.5kW
4P

11kW
4P

Drive Unit

Dimension Selection
Tables
Tables

15kW
4P

18.5kW
4P

22kW
4P

30kW
4P

37kW
4P

45kW
4P

55kW
4P

75kW
4P

90kW
4P

110kW
4P

B - 74

SF

1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2

Combinations with 4P motor

1500r/min

40Dgree

238

211

188

168

150

134

6.3

7.1

10

11.2

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9025
9030
9030
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9055
9055
9055
9055
9060
9060
9060
9060
9065
9065
9065
9065

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9015
9015
9025
9025
9025
9025
9025
9030
9030
9030
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9055
9055
9055
9055
9055
9055
9055
9055
9065
9065
9065
9065

Size of Reducer

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9025
9025
9025
9025
9040
9040
9040
9040
9040
9040
9040
9040
9050
9050
9050
9050

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9030
9030
9030
9030
9040
9040
9040
9040
9040
9040
9040
9040
9050
9050
9050
9050

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9030
9030
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9055
9055
9055
9055
9055
9055
9055
9055

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9025
9030
9030
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9055
9055
9055
9055
9055
9055
9055
9055
9065
9065
9065
9065

Low Speed Shaft Speedr/min

107 94
83
75
67
60
Nominal Reduction Ratio
12.5 14
16
18
20 22.4 25
9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9025 9015 9025 9025
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9025 9025
9015 9015 9015 9025 9025 9025 9025
9015 9025 9025 9025 9025 9030 9030
9015 9015 9015 9015 9025 9025 9025
9015 9015 9015 9025 9025 9025 9025
9015 9025 9025 9025 9025 9025 9025
9025 9025 9025 9030 9030 9030 9030
9015 9015 9025 9025 9025 9025 9025
9015 9025 9025 9025 9025 9025 9025
9025 9025 9025 9025 9025 9030 9030
9025 9030 9030 9030 9030 9030 9035
9025 9025 9025 9030 9030 9035 9035
9025 9025 9025 9030 9030 9035 9035
9025 9030 9030 9030 9030 9035 9035
9030 9030 9030 9035 9035 9040 9040
9030 9030 9030 9035 9035 9035 9040
9030 9030 9030 9035 9035 9035 9040
9030 9030 9030 9035 9035 9035 9040
9030 9035 9035 9040 9040 9045 9045
9035 9035 9035 9035 9035 9045 9045
9035 9035 9035 9035 9035 9045 9045
9035 9035 9035 9035 9040 9045 9045
9035 9035 9040 9045 9045 9050 9050
9040 9040 9045 9045 9045 9045 9055
9040 9040 9045 9045 9045 9045 9055
9040 9040 9045 9045 9045 9045 9055
9040 9045 9045 9050 9050 9055 9055
9055 9055 9055 9055 9055 9055 9065
9055 9055 9055 9055 9055 9055 9065
9055 9055 9055 9055 9055 9055 9065
9055 9055 9055 9055 9055 9060 9065
9060 9060 9060 9060 9065 9065 9070
9060 9060 9060 9060 9065 9065 9070
9060 9060 9060 9060 9065 9065 9070
9060 9060 9060 9060 9065 9065 9070
9065 9065 9065 9070 9075 9075 9075
9065 9065 9065 9070 9075 9075 9075
9065 9065 9065 9070 9075 9075 9075
9065 9065 9065 9070 9075 9075 9075
120

54

48

42

38

33

30

28
9015
9015
9015
9015
9015
9015
9015
9025
9015
9015
9025
9025
9025
9025
9025
9030
9025
9025
9030
9030
9025
9030
9030
9035
9035
9035
9035
9045
9040
9040
9045
9050
9045
9045
9045
9055
9055
9055
9055
9055
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075

31.5
9015
9015
9015
9015
9015
9015
9015
9025
9015
9015
9025
9030
9025
9025
9030
9030
9025
9030
9030
9035
9030
9030
9035
9040
9035
9035
9040
9045
9040
9040
9045
9050
9045
9045
9045
9055
9055
9055
9055
9060
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075

35.5
9015
9015
9015
9015
9015
9015
9015
9025
9015
9025
9025
9030
9025
9030
9030
9035
9030
9030
9030
9035
9030
9030
9035
9045
9035
9035
9045
9050
9040
9045
9045
9055
9045
9045
9050
9060
9055
9055
9055
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075
9075

40
9015
9015
9015
9015
9015
9015
9015
9025
9015
9025
9025
9030
9025
9030
9030
9035
9030
9030
9035
9040
9030
9035
9035
9045
9035
9040
9045
9050
9040
9045
9050
9055
9045
9050
9055
9060
9055
9055
9055
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075
9080

45
9015
9015
9015
9025
9015
9025
9025
9030
9025
9025
9030
9030
9030
9030
9030
9035
9030
9035
9035
9045
9030
9035
9040
9045
9035
9045
9045
9055
9045
9050
9055
9060
9045
9055
9055
9070
9055
9055
9065
9065
9065
9065
9070
9075
9070
9070
9075
9080
9075
9075
9075
9085

50
9030
9030
9030
9030
9030
9030
9030
9030
9030
9030
9030
9035
9030
9030
9035
9040
9030
9035
9040
9045
9035
9040
9040
9050
9040
9045
9050
9055
9045
9050
9055
9060
9055
9055
9060
9070
9055
9060
9060
9065
9065
9065
9070
9075
9075
9075
9075
9080
9075
9075
9075
9085

SELECTION Drive Unit Parallel Shaft

Low Speed Shaft Speedr/min

27
24
21
19
17
Nominal Reduction Ratio
56
63
71
80
90
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9035 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9035 9035 9045
9035 9040 9040 9045 9045
9030 9030 9035 9035 9035
9035 9035 9035 9045 9045
9035 9040 9045 9045 9045
9045 9045 9050 9055 9055
9030 9035 9035 9045 9045
9035 9040 9045 9045 9045
9045 9045 9045 9055 9055
9050 9050 9055 9055 9065
9035 9040 9040 9045 9045
9040 9045 9045 9055 9055
9045 9045 9055 9055 9055
9055 9055 9055 9065 9065
9045 9045 9050 9055 9055
9050 9050 9055 9055 9065
9055 9055 9060 9065 9065
9060 9060 9065 9065 9075
9050 9050 9055 9055 9065
9055 9055 9060 9065 9065
9060 9060 9065 9065 9075
9065 9065 9070 9075 9075
9055 9055 9060 9065 9065
9060 9060 9065 9065 9075
9065 9065 9065 9065 9075
9070 9070 9075 9075 9085
9060 9060 9065 9065 9075
9065 9065 9065 9075 9075
9065 9065 9070 9075 9075
9075 9075 9080 9085 9085
9070 9070 9070 9075 9075
9070 9070 9075 9075 9085
9075 9075 9080 9085 9085
9080 9080 9085 9085 9085
9075 9075 9075 9075 9085
9075 9075 9080 9085 9085
9075 9080 9085 9085 9085
9085 9085 9085 9085 9085
9080 9085 9085 9085 9085
9080 9085 9085 9085 9085
9085 9085 9085 9085 9085
9085 9085 9085 9085 9085

SF

1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2

Combinations with 4P motor

kW

5.5kW
4P

7.5kW
4P

11kW
4P

15kW
4P

18.5kW
4P

22kW
4P

30kW
4P

37kW
4P

45kW
4P

55kW
4P

75kW
4P

90kW
4P

110kW
4P

B - 75

SELECTION Drive Unit Parallel Shaft

Shaft Position

High Speed Shaft Speed Ambient Temperature

Parallel Shaft

kW

5.5kW
4P

7.5kW
4P

11kW
4P

Drive Unit

Dimension Selection
Tables
Tables

15kW
4P

18.5kW
4P

22kW
4P

30kW
4P

37kW
4P

45kW
4P

55kW
4P

75kW
4P

90kW
4P

110kW
4P

B - 76

SF

1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2

Combinations with 4P motor

1800r/min

40 Dgree

286

254

225

200

180

161

6.3

7.1

10

11.2

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9030
9030
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9055
9055
9055
9055
9055
9055
9055
9055
9065
9065
9065
9065

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9030
9030
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9055
9055
9055
9055
9055
9055
9055
9055
9065
9065
9065
9065

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9025
9030
9030
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9055
9055
9055
9055
9060
9060
9060
9060
9065
9065
9065
9065

Size of Reducer

9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9030
9030
9030
9030

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9030
9030
9030
9030

9040
9040
9040
9040

9040
9040
9040
9040

9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9025
9025
9025
9030
9030
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9055
9055
9055
9055

Low Speed Shaft Speedr/min

129 113 100 90
80
72
Nominal Reduction Ratio
12.5 14
16
18
20 22.4 25
9015 9015 9015 9015
9015 9015 9015 9015
9015 9015 9015 9015
9015 9015 9015 9015
9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9025 9025
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9015 9015
9015 9015 9015 9015 9015 9025 9025
9015 9015 9015 9025 9025 9025 9025
9015 9015 9015 9015 9025 9025 9025
9015 9015 9015 9015 9025 9025 9025
9015 9015 9015 9025 9025 9025 9025
9015 9025 9025 9025 9025 9030 9030
9015 9015 9015 9025 9025 9025 9025
9015 9015 9015 9025 9025 9025 9025
9015 9025 9025 9025 9025 9025 9030
9025 9025 9025 9030 9030 9030 9030
9025 9025 9025 9030 9030 9035 9035
9025 9025 9025 9030 9030 9035 9035
9025 9025 9025 9030 9030 9035 9035
9025 9030 9030 9030 9030 9035 9035
9030 9030 9030 9030 9035 9035 9035
9030 9030 9030 9030 9035 9035 9035
9030 9030 9030 9030 9035 9035 9035
9030 9030 9035 9035 9035 9040 9040
9035 9035 9035 9035 9035 9045 9045
9035 9035 9035 9035 9035 9045 9045
9035 9035 9035 9035 9035 9045 9045
9035 9035 9035 9040 9040 9045 9045
9040 9040 9045 9045 9045 9045 9055
9040 9040 9045 9045 9045 9045 9055
9040 9040 9045 9045 9045 9045 9055
9040 9040 9045 9045 9045 9050 9055
9055 9055 9055 9055 9055 9055 9065
9055 9055 9055 9055 9055 9055 9065
9055 9055 9055 9055 9055 9055 9065
9055 9055 9055 9055 9055 9060 9065
9060 9060 9060 9060 9065 9065 9070
9060 9060 9060 9060 9065 9065 9070
9060 9060 9060 9060 9065 9065 9070
9060 9060 9060 9060 9065 9065 9070
9065 9065 9065 9070 9075 9075 9075
9065 9065 9065 9070 9075 9075 9075
9065 9065 9065 9070 9075 9075 9075
9065 9065 9065 9070 9075 9075 9075
144

64

57

51

45

40

36

28
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9015
9025
9025
9030
9025
9025
9025
9030
9025
9025
9030
9030
9035
9035
9035
9040
9040
9040
9040
9045
9045
9045
9045
9050
9055
9055
9055
9055
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075

31.5
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9015
9025
9015
9025
9025
9030
9025
9025
9030
9030
9025
9030
9030
9035
9035
9035
9035
9040
9040
9040
9040
9045
9045
9045
9045
9050
9055
9055
9055
9055
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075

35.5
9015
9015
9015
9015
9015
9015
9015
9025
9015
9025
9025
9030
9025
9025
9030
9030
9025
9030
9030
9035
9030
9030
9030
9035
9035
9035
9035
9045
9040
9040
9045
9050
9045
9045
9045
9055
9055
9055
9055
9060
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075

40
9015
9015
9015
9015
9015
9015
9015
9025
9015
9025
9025
9030
9025
9025
9030
9030
9025
9030
9030
9035
9030
9030
9030
9040
9035
9035
9040
9045
9040
9040
9045
9050
9045
9045
9050
9055
9055
9055
9055
9060
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075

45
9015
9015
9015
9015
9015
9015
9025
9025
9015
9025
9025
9030
9025
9030
9030
9035
9030
9030
9035
9040
9030
9030
9035
9045
9035
9040
9045
9050
9040
9045
9050
9055
9045
9050
9055
9060
9055
9055
9055
9065
9065
9065
9065
9070
9070
9070
9070
9075
9075
9075
9075
9080

50
9030
9030
9030
9030
9030
9030
9030
9030
9030
9030
9030
9035
9030
9030
9030
9035
9030
9030
9035
9040
9030
9035
9040
9045
9035
9040
9045
9050
9040
9045
9050
9055
9045
9050
9055
9060
9055
9055
9060
9065
9065
9065
9065
9075
9075
9075
9075
9075
9080
9080
9080
9085

SELECTION Drive Unit Parallel Shaft

Low Speed Shaft Speedr/min

32
29
25
23
20
Nominal Reduction Ratio
56
63
71
80
90
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9035 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9030 9030 9035 9035
9030 9035 9035 9045 9045
9030 9030 9030 9035 9035
9030 9030 9035 9035 9035
9035 9035 9035 9045 9045
9040 9040 9045 9045 9055
9030 9030 9035 9035 9035
9035 9035 9035 9045 9045
9035 9040 9045 9045 9045
9045 9045 9050 9055 9055
9030 9035 9035 9045 9045
9035 9040 9045 9045 9045
9040 9045 9045 9055 9055
9050 9050 9055 9055 9065
9040 9040 9045 9045 9055
9045 9045 9050 9055 9055
9050 9050 9055 9055 9065
9055 9055 9060 9065 9065
9045 9045 9050 9055 9055
9050 9050 9055 9055 9065
9055 9055 9060 9065 9065
9060 9060 9065 9065 9075
9050 9055 9055 9055 9065
9055 9055 9060 9065 9065
9060 9060 9065 9065 9075
9065 9065 9070 9075 9075
9055 9060 9060 9065 9065
9060 9060 9065 9065 9075
9065 9065 9065 9065 9075
9070 9070 9075 9075 9085
9070 9070 9070 9075 9075
9070 9070 9070 9075 9075
9070 9070 9075 9075 9085
9075 9075 9080 9085 9085
9075 9075 9075 9075 9075
9075 9075 9075 9075 9085
9075 9075 9080 9085 9085
9080 9085 9085 9085 9085
9080 9085 9085 9085 9085
9080 9085 9085 9085 9085
9080 9085 9085 9085 9085
9085 9085 9085 9085 9085

SF

1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2
1
1.25
1.5
2

Combinations with 4P motor

kW

5.5kW
4P

7.5kW
4P

11kW
4P

15kW
4P

18.5kW
4P

22kW
4P

30kW
4P

37kW
4P

45kW
4P

55kW
4P

75kW
4P

90kW
4P

110kW
4P

B - 77

SELECTION Drive Unit Parallel Shaft

5.5kW

Frequency Hz
Pole
P
5RGGFn1 r/min

50Hz
4
1500

5.5kW, 7.5kW

60Hz
4
1800

Frequency
Output Speed
r/min
107
93.8
83.3
75.0
67.0
60.0

Drive Unit

Dimension Selection
Tables
Tables

50Hz
Output Torque (Tout)
Nm
kgf m
490
50
560
57
630
64
700
72
784
80
875
89

53.6

980

100

47.6

1100

113

42.3

1240

127

37.5

1400

143

33.3

1580

161

30.0

1750

179

26.8

1960

200

23.8

2210

225

21.1

2490

254

18.8

2800

286

16.7

3150

322

7.5kW

SF
4.74
4.70
3.83
4.01
3.27
3.23
2.63
4.25
2.56
3.96
2.09
3.25
2.07
3.21
4.63
1.69
2.63
4.16
3.72
4.85
3.36
4.41
3.00
3.90
4.92
2.69
3.56
4.03
3.12
2.85
4.23

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min
129
113
100
90.0
80.4
72.0

60Hz
Output Torque (Tout)
Nm
kgf m
409
42
467
48
525
54
584
60
654
67
730
74

64.3

817

83

57.1

919

94

50.7

1040

106

45.0

1170

119

40.0

1310

134

36.0

1460

149

32.1

1630

167

28.6

1840

188

25.4

2070

212

22.5

2330

238

20.0

2630

268

50Hz
4
1500

SF

Size

Assembly

5.63
5.63
4.60
4.80
3.90
3.89
3.16
5.09
3.07
4.74
2.49
3.89
2.47
3.85
5.45
2.01
3.16
5.00
4.47
5.63
4.01
5.29
3.58
4.67
5.81
3.21
4.25
4.83
3.74
3.41
5.07

9015
9015
9015
9015
9015
9015
9015
9025
9015
9025
9015
9025
9015
9025
9030
9015
9025
9030
9030
9035
9030
9035
9030
9035
9040
9030
9035
9040
9035
9035
9045

P2
P2
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min
134
120
107
93.8

B - 78

83.3

860

88

75.0

955

98

67.0

1070

109

60.0

1190

122

53.6

1340

137

47.6

1500

154

42.3

1700

173

SF
4.26
4.26
3.48
3.45
2.81
4.53
2.94
4.40
2.40
3.84
2.37
3.76
1.93
3.11
4.93
1.88
2.90
4.13
1.53
2.38
3.81

Output Speed
r/min
161
144
129
113

Reduction
Ratio
14
16
18
20
22.4
25
28
28
31.5
31.5
35.5
35.5
40
40
40
45
45
45
50
50
56
56
63
63
63
71
71
71
80
90
90

Vertical
B-102
B-102
B-102
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m
535
55
597
61
669
68
764
78

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m
446
46
497
51
557
57
637
65

100

716

73

90.0

796

81

80.4

891

91

72.0

995

102

64.3

1110

114

57.1

1250

128

50.7

1410

144

Page of
Dimension Sheet

Model
SF

Size

Assembly

5.20
5.06
4.13
4.13
3.37
5.46
3.52
5.20
2.86
4.53
2.85
4.26
2.31
3.73
5.86
2.25
3.48
5.06
1.82
2.85
4.53

9015
9015
9015
9015
9015
9025
9015
9025
9015
9025
9015
9025
9015
9025
9030
9015
9025
9030
9015
9025
9030

P2
P2
P2
P2
P2
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Reduction
Ratio
11.2
12.5
14
16
18
18
20
20
22.4
22.4
25
25
28
28
28
31.5
31.5
31.5
35.5
35.5
35.5

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106

SELECTION Drive Unit Parallel Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

37.5

1910

195

33.3

2150

219

30.0

2390

244

26.8

2670

273

23.8

3010

307

21.1

3390

346

18.8

3820

390

16.7

4300

439

11kW

SF
1.52
2.36
3.40
4.40
1.24
1.93
3.05
4.00
4.53
2.73
3.56
4.40
2.46
3.24
3.68
4.88
2.20
2.86
3.61
4.50
1.97
2.61
2.96
3.86
4.26
2.29
3.65
2.09
3.10
4.53

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

45.0

1590

163

40.0

1790

183

36.0

1990

203

32.1

2230

228

28.6

2510

256

25.4

2830

288

22.5

3180

325

20.0

3580

366

50Hz
4
1500

Output Speed
r/min
211
188
167
150
134

784

80

120

875

89

107

980

100

93.8

1120

114

83.3

1260

129

75.0

1400

143

SF
4.72
4.63
3.72
3.63
2.90
4.81
2.90
4.63
2.37
3.81
2.35
3.81
1.91
3.09
4.90
2.00
3.00
4.63

Output Speed
r/min
254
225
200
180

Page of
Dimension Sheet

Model
SF

Size

Assembly

1.81
2.82
4.00
5.20
1.48
2.31
3.66
4.80
5.46
3.28
4.13
5.33
2.94
3.88
4.40
5.84
2.62
3.42
4.26
5.41
2.36
3.11
3.54
4.62
5.20
2.74
4.38
2.50
3.72
5.33

9015
9025
9030
9035
9015
9025
9030
9035
9040
9030
9035
9040
9030
9035
9040
9045
9030
9035
9040
9045
9030
9035
9040
9045
9050
9035
9045
9035
9045
9055

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Reduction
Ratio
40
40
40
40
45
45
45
45
45
50
50
50
56
56
56
56
63
63
63
63
71
71
71
71
71
80
80
90
90
90

Vertical
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m
497
51
560
57
630
64
700
72

7.5kW, 11kW

60Hz
Output Torque (Tout)
Nm
kgf m
414
42
467
48
525
54
584
60

161

654

67

144

730

74

129

817

83

113

934

95

100

1050

107

90.0

1170

119

Page of
Dimension Sheet

Model
SF

Size

Assembly

5.63
5.54
4.45
4.27
3.54
5.81
3.45
5.54
2.81
4.54
2.81
4.54
2.30
3.72
5.90
2.40
3.54
5.54

9015
9015
9015
9015
9015
9025
9015
9025
9015
9025
9015
9025
9015
9025
9030
9015
9025
9030

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P3
P3

Reduction
Ratio
7.1
8
9
10
11.2
11.2
12.5
12.5
14
14
16
16
18
18
18
20
20
20

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-106
B-106
B-106

B - 79

SELECTION Drive Unit Parallel Shaft

11kW

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

67.0

1570

160

60.0

1750

179

53.6

1960

200

47.6

2210

225

42.3

2490

254

37.5

2800

286

33.3

3150

322

30.0

3500

358

26.8

3920

400

23.8

4410

450

21.1

4970

508

18.8

5600

572

16.7

6300

644

Drive Unit

Dimension Selection
Tables
Tables

B - 80

SF
1.63
2.61
4.18
1.61
2.56
3.72
4.81
1.31
2.12
3.36
4.36
4.90
1.28
1.98
2.81
3.81
4.72
1.04
1.62
2.60
3.54
3.90
1.03
1.60
2.31
3.00
3.81
4.85
0.84
1.31
2.08
2.72
3.09
4.12
4.72
1.86
2.42
3.00
3.93
4.63
1.68
2.20
2.50
3.32
3.81
4.90
1.50
1.95
2.46
3.07
3.54
5.00
1.34
1.78
2.01
2.63
2.90
4.00
4.54
1.56
2.49
3.81
1.42
2.11
3.09
4.81

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

80.4

1310

133

72.0

1460

149

64.3

1630

167

57.1

1840

188

50.7

2070

212

45.0

2330

238

40.0

2630

268

36.0

2920

298

32.1

3270

334

28.6

3680

375

25.4

4140

423

22.5

4670

477

20.0

5250

536

Page of
Dimension Sheet

Model
SF

Size

Assembly

1.95
3.09
5.00
1.94
2.90
4.45
5.81
1.58
2.54
4.00
5.27
5.90
1.53
2.37
3.45
4.63
5.72
1.24
1.94
3.09
4.18
4.63
1.23
1.92
2.72
3.54
4.54
5.82
1.00
1.58
2.50
3.27
3.72
4.94
5.63
2.23
2.81
3.63
4.71
5.54
2.00
2.64
3.00
3.98
4.54
5.90
1.79
2.33
2.90
3.69
4.27
6.00
1.60
2.12
2.41
3.15
3.54
4.81
5.45
1.87
2.99
4.54
1.70
2.53
3.63
5.76

9015
9025
9030
9015
9025
9030
9035
9015
9025
9030
9035
9040
9015
9025
9030
9035
9040
9015
9025
9030
9035
9040
9015
9025
9030
9035
9040
9045
9015
9025
9030
9035
9040
9045
9050
9030
9035
9040
9045
9050
9030
9035
9040
9045
9050
9055
9030
9035
9040
9045
9050
9055
9030
9035
9040
9045
9050
9055
9060
9035
9045
9055
9035
9045
9055
9065

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Reduction
Ratio
22.4
22.4
22.4
25
25
25
25
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
45
45
45
45
45
45
45
50
50
50
50
50
56
56
56
56
56
56
63
63
63
63
63
63
71
71
71
71
71
71
71
80
80
80
90
90
90
90

Vertical
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-106
B-106

SELECTION Drive Unit Parallel Shaft

15kW

Frequency Hz
Pole
P
5RGGFn1 r/min

50Hz
4
1500

60Hz
4
1800

Frequency
Output Speed
r/min
238
211
188

50Hz
Output Torque (Tout)
Nm
kgf m
602
61
678
69
764
78

167

860

88

150

955

98

134

1070

109

120

1190

122

107

1340

137

93.8

1530

156

83.3

1720

176

75.0

1910

195

67.0

2140

218

60.0

2390

244

53.6

2670

273

47.6

3010

307

42.3

3390

346

37.5

3820

390

SF
4.26
3.46
3.40
2.73
4.53
2.66
4.33
2.13
3.53
2.13
3.40
5.00
1.74
2.80
4.46
1.72
2.80
4.00
1.40
2.26
3.60
4.73
1.47
2.20
3.40
4.20
1.20
1.92
3.06
3.80
4.46
4.55
1.18
1.88
2.73
3.53
4.40
0.96
1.55
2.46
3.20
3.60
4.72
0.94
1.45
2.06
2.08
3.46
4.53
1.19
1.90
2.60
2.86
3.80
4.53
1.18
1.70
2.20
2.80
3.56
4.20

Output Speed
r/min
286
254
225

15kW

60Hz
Output Torque (Tout)
Nm
kgf m
501
51
565
58
637
65

200

716

73

180

796

81

161

891

91

144

995

102

129

1110

114

113

1270

130

100

1430

146

90.0

1590

163

80.4

1780

182

72.0

1990

203

64.3

2230

228

57.1

2510

256

50.7

2830

288

45.0

3180

325

Page of
Dimension Sheet

Model
SF

Size

Assembly

5.06
4.13
4.06
3.26
5.40
3.13
5.20
2.60
4.26
2.53
4.06
5.93
2.06
3.33
5.40
2.06
3.33
4.80
1.68
2.73
4.33
5.66
1.76
2.60
4.06
5.00
1.43
2.26
3.66
4.53
5.33
5.44
1.42
2.13
3.26
4.26
5.26
1.15
1.86
2.93
3.86
4.33
5.64
1.12
1.74
2.53
3.40
4.20
5.44
1.42
2.26
3.06
3.40
4.55
5.40
1.41
2.00
2.60
3.33
4.27
5.00

9015
9015
9015
9015
9025
9015
9025
9015
9025
9015
9025
9030
9015
9025
9030
9015
9025
9030
9015
9025
9030
9035
9015
9025
9030
9035
9015
9025
9030
9035
9040
9045
9015
9025
9030
9035
9040
9015
9025
9030
9035
9040
9045
9015
9025
9030
9035
9040
9045
9025
9030
9035
9040
9045
9050
9025
9030
9035
9040
9045
9050

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P3
P3
P2
P3
P3
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Reduction
Ratio
6.3
7.1
8
9
9
10
10
11.2
11.2
12.5
12.5
12.5
14
14
14
16
16
16
18
18
18
18
20
20
20
20
22.4
22.4
22.4
22.4
22.4
22.4
25
25
25
25
25
28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-106
B-106
B-106
B-102
B-106
B-106
B-106
B-102
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106

B - 81

SELECTION Drive Unit Parallel Shaft

15kW, 18.5kW

Frequency
Output Speed
r/min

Drive Unit

50Hz
Output Torque (Tout)
Nm
kgf m

33.3

4300

439

30.0

4780

488

26.8

5350

546

23.8

6020

614

21.1

6780

692

18.8

7640

780

16.7

8600

878

Dimension Selection
Tables
Tables

18.5kW

SF
0.96
1.52
2.00
2.26
3.02
3.46
4.73
1.36
1.78
2.20
2.88
3.40
4.46
1.23
1.62
1.84
2.44
2.80
3.60
4.40
1.10
1.43
1.80
2.25
2.60
3.66
4.26
0.98
1.30
1.48
1.93
2.13
2.93
3.33
4.61
1.14
1.82
2.80
4.58
1.04
1.55
2.26
3.53

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

40.0

3580

366

36.0

3980

406

32.1

4460

455

28.6

5010

512

25.4

5650

577

22.5

6370

650

20.0

7160

731

50Hz
4
1500

SF

Size

Assembly

1.15
1.83
2.40
2.73
3.62
4.13
5.66
1.64
2.06
2.66
3.46
4.06
5.40
1.47
1.94
2.20
2.92
3.33
4.33
5.26
1.31
1.71
2.13
2.70
3.13
4.40
5.13
1.18
1.55
1.77
2.31
2.60
3.53
4.00
5.52
1.37
2.19
3.33
5.65
1.25
1.86
2.66
4.22

9025
9030
9035
9040
9045
9050
9055
9030
9035
9040
9045
9050
9055
9030
9035
9040
9045
9050
9055
9060
9030
9035
9040
9045
9050
9055
9060
9030
9035
9040
9045
9050
9055
9060
9065
9035
9045
9055
9065
9035
9045
9055
9065

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min
238
211

836

85

188

942

96

167

1060

108

150

1180

120

134

1320

135

120

1470

150

SF
3.45
2.81
4.48
2.75
4.48
2.21
3.67
2.16
3.51
1.72
2.86
4.64
1.72
4.05

B - 82

Output Speed
r/min
286

Reduction
Ratio
45
45
45
45
45
45
45
50
50
50
50
50
50
56
56
56
56
56
56
56
63
63
63
63
63
63
63
71
71
71
71
71
71
71
71
80
80
80
80
90
90
90
90

Vertical
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m
742
76

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m
618
63

254

697

71

225

785

80

200

883

90

180

982

100

161

1100

112

144

1230

125

Page of
Dimension Sheet

Model
SF

Size

Assembly

4.10
3.35
5.40
3.29
5.35
2.64
4.37
2.54
4.21
2.10
3.45
5.56
2.05
3.29
4.81

9015
9015
9025
9015
9025
9015
9025
9015
9025
9015
9025
9030
9015
9025
9030

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2

Reduction
Ratio
6.3
7.1
7.1
8
8
9
9
10
10
11.2
11.2
11.2
12.5
12.5
12.5

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102

Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

107

1650

168

93.8

1880

192

83.3

2120

216

75.0

2360

241

67.0

2640

269

60.0

2940

301

53.6

3300

337

47.6

3710

379

42.3

4180

427

37.5

4710

481

33.3

5300

541

30.0

5890

601

SELECTION Drive Unit Parallel Shaft

18.5kW

Frequency

Page of
Dimension Sheet

SF
1.41
2.27
3.62
4.91
1.40
2.27
3.24
4.21
1.14
1.83
2.91
3.83
4.32
1.78
2.75
3.40
4.43
1.55
2.48
3.08
3.62
4.55
1.52
2.21
2.86
3.56
4.53
1.26
2.00
2.59
2.91
3.82
4.37
1.17
1.67
2.27
2.81
3.67
4.43
0.96
1.54
2.10
2.32
3.08
3.67
4.59
0.95
1.37
1.78
2.27
2.88
3.40
4.75
1.23
1.62
1.83
2.45
2.81
3.83
4.43
1.10
1.44
1.78
2.34
2.75
3.62
4.54

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

129

1370

140

113

1570

160

100

1770

180

90.0

1960

200

80.4

2200

224

72.0

2450

251

64.3

2750

281

57.1

3090

316

50.7

3480

356

45.0

3930

401

40.0

4420

451

36.0

4910

501

Model
SF

Size

Assembly

1.67
2.70
4.37
5.89
1.67
2.70
3.89
5.08
1.36
2.21
3.51
4.59
5.13
2.10
3.29
4.05
5.29
1.83
2.97
3.67
4.32
5.44
1.72
2.64
3.45
4.27
5.43
1.51
2.37
3.13
3.51
4.57
5.24
1.41
2.05
2.75
3.40
4.41
5.29
1.15
1.83
2.48
2.75
3.69
4.37
5.45
1.14
1.62
2.10
2.70
3.46
4.05
5.67
1.48
1.94
2.21
2.94
3.35
4.59
5.29
1.32
1.67
2.16
2.80
3.29
4.37
5.40

9015
9025
9030
9035
9015
9025
9030
9035
9015
9025
9030
9035
9040
9025
9030
9035
9040
9025
9030
9035
9040
9045
9025
9030
9035
9040
9045
9025
9030
9035
9040
9045
9050
9025
9030
9035
9040
9045
9050
9025
9030
9035
9040
9045
9050
9055
9025
9030
9035
9040
9045
9050
9055
9030
9035
9040
9045
9050
9055
9060
9030
9035
9040
9045
9050
9055
9060

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P3
P2
P3
P3
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Reduction
Ratio
14
14
14
14
16
16
16
16
18
18
18
18
18
20
20
20
20
22.4
22.4
22.4
22.4
22.4
25
25
25
25
25
28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
40
45
45
45
45
45
45
45
50
50
50
50
50
50
50

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-106
B-106
B-102
B-106
B-106
B-106
B-102
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-106
B-108

B - 83

SELECTION Drive Unit Parallel Shaft

18.5kW, 22kW

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

26.8

6600

673

23.8

7420

758

21.1

8360

854

18.8

9420

962

16.7

10600

1080

Drive Unit

Dimension Selection
Tables
Tables

22kW

SF
1.00
1.31
1.49
1.97
2.27
2.91
3.56
4.64
0.89
1.16
1.46
1.82
2.10
2.97
3.45
4.80
1.05
1.20
1.56
1.72
2.37
2.70
3.74
4.48
0.92
1.48
2.27
3.71
0.84
1.25
1.83
2.86
4.75

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

32.1

5500

561

28.6

6180

631

25.4

6970

711

22.5

7850

802

20.0

8830

902

50Hz
4
1500

SF

Size

Assembly

1.19
1.57
1.78
2.36
2.70
3.51
4.27
5.56
1.06
1.38
1.72
2.19
2.54
3.56
4.16
5.76
1.26
1.43
1.87
2.10
2.86
3.24
4.47
5.35
1.11
1.77
2.70
4.45
1.01
1.50
2.16
3.42
5.67

9030
9035
9040
9045
9050
9055
9060
9065
9030
9035
9040
9045
9050
9055
9060
9065
9035
9040
9045
9050
9055
9060
9065
9070
9035
9045
9055
9065
9035
9045
9055
9065
9075

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min

B - 84

238

882

90

211

994

102

188

1120

114

167

1260

129

150

1400

143

134

1570

160

120

1750

179

107

1960

200

SF
2.90
4.63
2.36
3.77
2.31
3.77
1.86
3.09
4.77
1.81
2.95
4.36
1.45
2.40
3.90
1.45
2.31
3.40
4.54
1.18
1.90
3.04
4.13
4.50

Output Speed
r/min

Reduction
Ratio
56
56
56
56
56
56
56
56
63
63
63
63
63
63
63
63
71
71
71
71
71
71
71
71
80
80
80
80
90
90
90
90
90

Vertical
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-108
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-108
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m

286

735

75

254

829

85

225

934

95

200

1050

107

180

1170

119

161

1310

133

144

1460

149

129

1630

167

Page of
Dimension Sheet

Model
SF

Size

Assembly

3.45
5.54
2.81
4.54
2.77
4.50
2.22
3.68
5.72
2.13
3.54
5.22
1.77
2.90
4.68
1.72
2.77
4.04
5.45
1.40
2.27
3.68
4.95
5.36

9015
9025
9015
9025
9015
9025
9015
9025
9030
9015
9025
9030
9015
9025
9030
9015
9025
9030
9035
9015
9025
9030
6035
9040

P2
P2
P2
P2
P2
P2
P2
P2
P3
P2
P2
P3
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2

Reduction
Ratio
6.3
6.3
7.1
7.1
8
8
9
9
9
10
10
10
11.2
11.2
11.2
12.5
12.5
12.5
12.5
14
14
14
14
14

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102

SELECTION Drive Unit Parallel Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

93.8

2240

229

83.3

2520

257

75.0

2800

286

67.0

3140

320

60.0

3500

358

53.6

3920

400

47.6

4410

450

42.3

4970

508

37.5

5600

572

33.3

6300

644

30.0

7000

715

SF
1.17
1.90
2.72
3.54
4.40
1.54
2.45
3.22
3.63
4.75
1.50
2.31
2.86
3.72
4.68
1.30
2.09
2.59
3.04
3.82
4.81
1.28
1.86
2.40
3.00
3.80
4.45
1.06
1.68
2.18
2.45
3.21
3.68
0.99
1.40
1.90
2.36
3.09
3.72
4.77
1.30
1.77
1.95
2.59
3.09
3.86
4.86
1.15
1.50
1.90
2.42
2.86
4.00
4.72
1.04
1.36
1.54
2.06
2.36
3.22
3.72
0.93
1.21
1.50
1.96
2.31
3.04
3.81

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

113

1870

191

100

2100

215

90.0

2330

238

80.4

2610

267

72.0

2920

298

64.3

3270

334

57.1

3680

375

50.7

4140

423

45.0

4670

477

40.0

5250

536

36.0

5840

596

Page of
Dimension Sheet

Model
SF

Size

Assembly

1.40
2.27
3.27
4.27
5.27
1.86
2.95
3.86
4.31
5.67
1.77
2.77
3.40
4.45
5.60
1.54
2.50
3.09
3.63
4.57
5.77
1.45
2.22
2.90
3.59
4.57
5.36
1.27
2.00
2.63
2.95
3.85
4.40
1.18
1.72
2.31
2.86
3.70
4.45
5.72
1.54
2.09
2.31
3.10
3.68
4.59
5.81
1.36
1.77
2.27
2.91
3.40
4.77
5.68
1.25
1.63
1.86
2.47
2.81
3.86
4.45
1.11
1.40
1.81
2.35
2.77
3.68
4.54

9015
9025
9030
9035
9040
9025
9030
9035
9040
9045
9025
9030
9035
9040
9045
9025
9030
9035
9040
9045
9050
9025
9030
9035
9040
9045
9050
9025
9030
9035
9040
9045
9050
9025
9030
9035
9040
9045
9050
9055
9030
9035
9040
9045
9050
9055
9060
9030
9035
9040
9045
9050
9055
9060
9030
9035
9040
9045
9050
9055
9060
9030
9035
9040
9045
9050
9055
9060

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P3
P2
P3
P2
P3
P3
P2
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

22kW

Reduction
Ratio
16
16
16
16
16
18
18
18
18
18
20
20
20
20
20
22.4
22.4
22.4
22.4
22.4
22.4
25
25
25
25
25
25
28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
40
45
45
45
45
45
45
45
50
50
50
50
50
50
50

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-106
B-106
B-102
B-106
B-102
B-106
B-106
B-102
B-106
B-102
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-106
B-108

B - 85

SELECTION Drive Unit Parallel Shaft

22kW, 30kW

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

26.8

7840

801

23.8

8820

901

21.1

9940

1020

18.8

11210

1140

16.7

12610

1290

Dimension Selection
Tables
Tables

Drive Unit

30kW

SF
0.84
1.10
1.25
1.66
1.90
2.45
3.00
3.90
4.68
0.97
1.23
1.53
1.77
2.50
2.90
4.04
4.50
0.89
1.00
1.31
1.45
2.00
2.27
3.14
3.77
4.95
1.24
1.90
3.12
4.77
1.05
1.54
2.40
4.00

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

32.1

6540

667

28.6

7350

751

25.4

8290

846

22.5

9340

953

20.0

10510

1070

50Hz
4
1500

SF

Size

Assembly

1.00
1.32
1.50
1.99
2.27
2.95
3.59
4.67
5.59
1.16
1.45
1.84
2.13
3.00
3.50
4.84
5.40
1.06
1.20
1.57
1.77
2.40
2.72
3.76
4.50
5.95
1.49
2.27
3.75
5.68
1.26
1.81
2.88
4.77

9030
9035
9040
9045
9050
9055
9060
9065
9070
9035
9040
9045
9050
9055
9060
9065
9070
9035
9040
9045
9050
9055
9060
9065
9070
9075
9045
9055
9065
9075
9045
9055
9065
9075

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min

B - 86

238

1200

123

211

1360

138

188

1530

156

167

1720

176

150

1910

195

134

2140

218

120

2390

244

107

2670

273

SF
3.40
4.96
2.76
4.50
2.76
3.90
2.26
3.50
4.73
2.16
3.20
4.06
1.76
2.86
3.70
4.30
1.70
2.50
3.33
4.03
1.40
2.23
3.03
3.30
4.54

Output Speed
r/min

Reduction
Ratio
56
56
56
56
56
56
56
56
56
63
63
63
63
63
63
63
63
71
71
71
71
71
71
71
71
71
80
80
80
80
90
90
90
90

Vertical
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-106
B-106
B-108
B-108
B-106
B-106
B-108
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m

286

1000

102

254

1130

115

225

1270

130

200

1430

146

180

1590

163

161

1780

182

144

1990

203

129

2230

228

Page of
Dimension Sheet

Model
SF

Size

Assembly

4.06
5.96
3.33
5.36
3.30
4.66
2.70
4.20
5.66
2.60
3.83
4.86
2.13
3.43
4.43
5.13
2.03
2.96
4.00
4.83
1.66
2.70
3.63
3.93
5.42

9025
9030
9025
9030
9025
9030
9025
9030
9035
9025
9030
9035
9025
9030
9035
9040
9025
9030
9035
9040
9025
9030
9035
9040
9045

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2

Reduction
Ratio
6.3
6.3
7.1
7.1
8
8
9
9
9
10
10
10
11.2
11.2
11.2
11.2
12.5
12.5
12.5
12.5
14
14
14
14
14

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102

SELECTION Drive Unit Parallel Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

93.8

3060

312

83.3

3440

351

75.0

3820

390

67.0

4280

437

60.0

4780

488

53.6

5350

546

47.6

6020

614

42.3

6780

692

37.5

7640

780

33.3

8600

878

30.0

9550

975

SF
1.40
2.00
2.60
3.23
4.26
4.73
1.80
2.36
2.66
3.48
3.90
1.70
2.10
2.73
3.43
4.30
1.90
2.23
2.80
3.53
4.06
1.76
2.20
2.79
3.26
4.59
1.60
1.80
2.36
2.70
3.70
4.30
1.40
1.73
2.26
2.73
3.50
4.53
1.30
1.43
1.90
2.26
2.83
3.56
4.48
1.10
1.40
1.78
2.10
2.93
3.46
4.83
1.00
1.13
1.51
1.73
2.36
2.73
3.74
4.46
0.89
1.10
1.44
1.70
2.23
2.80
3.72
4.13

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

113

2550

260

100

2870

293

90.0

3180

325

80.4

3570

364

72.0

3980

406

64.3

4460

455

57.1

5010

512

50.7

5650

577

45.0

6370

650

40.0

7160

731

36.0

7960

813

Page of
Dimension Sheet

Model
SF

Size

Assembly

1.66
2.40
3.13
3.86
5.09
5.66
2.16
2.83
3.16
4.16
4.66
2.03
2.50
3.26
4.10
5.13
2.26
2.66
3.35
4.23
4.86
2.13
2.63
3.35
3.93
5.50
1.93
2.16
2.82
3.23
4.40
5.13
1.70
2.10
2.72
3.26
4.20
5.43
1.53
1.70
2.27
2.70
3.36
4.26
5.36
1.30
1.66
2.13
2.50
3.50
4.16
5.80
1.20
1.36
1.81
2.06
2.83
3.26
4.47
5.33
1.03
1.33
1.73
2.03
2.70
3.33
4.45
4.93

9025
9030
9035
9040
9045
9050
9030
9035
9040
9045
9050
9030
9035
9040
9045
9050
9035
9040
9045
9050
9055
9035
9040
9045
9050
9055
9035
9040
9045
9050
9055
9060
9035
9040
9045
9050
9055
9060
9035
9040
9045
9050
9055
9060
9065
9035
9040
9045
9050
9055
9060
9065
9035
9040
9045
9050
9055
9060
9065
9070
9035
9040
9045
9050
9055
9060
9065
9070

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P2
P3
P2
P3
P2
P3
P2
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

30kW

Reduction
Ratio
16
16
16
16
16
16
18
18
18
18
18
20
20
20
20
20
22.4
22.4
22.4
22.4
22.4
25
25
25
25
25
28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
40
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-106
B-102
B-106
B-102
B-106
B-102
B-106
B-102
B-106
B-102
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-108
B-108

B - 87

SELECTION Drive Unit Parallel Shaft

30kW, 37kW

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

26.8

10700

1090

23.8

12030

1230

21.1

13560

1380

18.8

15280

1560

16.7

17190

1760

Dimension Selection
Tables
Tables

Drive Unit

37kW

SF
0.92
1.22
1.40
1.80
2.20
2.86
3.43
4.73
0.90
1.12
1.30
1.83
2.13
2.96
3.30
4.36
5.00
0.96
1.06
1.46
1.66
2.30
2.76
3.63
4.33
0.91
1.40
2.29
3.50
1.13
1.76
2.93
4.53

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

32.1

8910

910

28.6

10030

1020

25.4

11300

1150

22.5

12730

1300

20.0

14330

1460

50Hz
4
1500

SF

Size

Assembly

1.10
1.46
1.66
2.16
2.63
3.43
4.09
5.66
1.06
1.35
1.56
2.20
2.56
3.55
3.96
5.20
5.96
1.15
1.30
1.76
2.00
2.76
3.30
4.36
5.16
1.09
1.66
2.75
4.16
1.33
2.11
3.50
5.40

9040
9045
9050
9055
9060
9065
9070
9075
9040
9045
9050
9055
9060
9065
9070
9075
9080
9045
9050
9055
9060
9065
9070
9075
9080
9045
9055
9065
9075
9055
9065
9075
9075

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min

B - 88

238

1480

152

211

1670

171

188

1880

192

167

2120

216

150

2360

241

134

2640

269

120

2940

301

107

3300

337

SF
2.75
4.02
3.64
3.16
4.21
2.83
3.83
4.27
2.59
3.29
4.27
2.32
3.00
3.48
4.48
2.02
2.70
3.27
4.47
5.00
1.81
2.45
2.67
3.68
4.13

Output Speed
r/min

Reduction
Ratio
56
56
56
56
56
56
56
56
63
63
63
63
63
63
63
63
63
71
71
71
71
71
71
71
71
80
80
80
80
90
90
90
90

Vertical
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-108
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-108
B-106
B-106
B-108
B-108
B-106
B-108
B-108
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m

286

1240

126

254

1390

142

225

1570

160

200

1770

180

180

1960

200

161

2200

224

144

2450

251

129

2750

281

Page of
Dimension Sheet

Model
SF

Size

Assembly

3.29
4.83
4.35
3.78
5.05
3.40
4.59
5.08
3.10
3.94
5.08
2.78
3.59
4.16
5.35
2.40
3.24
3.91
5.16
6.00
2.18
2.94
3.18
4.39
4.94

9025
9030
9030
9030
9035
9030
9035
9040
9030
9035
9040
9030
9035
9040
9045
9030
9035
9040
9045
9050
9030
9035
9040
9045
9050

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2

Reduction
Ratio
6.3
6.3
7.1
8
8
9
9
9
10
10
10
11.2
11.2
11.2
11.2
12.5
12.5
12.5
12.5
12.5
14
14
14
14
14

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102

SELECTION Drive Unit Parallel Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

93.8

3770

385

83.3

4240

433

75.0

4710

481

67.0

5280

539

60.0

5890

601

53.6

6600

673

47.6

7420

758

42.3

8360

854

37.5

9420

962

33.3

10600

1080

30.0

11780

1200

SF
1.62
2.10
2.62
3.45
3.83
1.45
1.91
2.16
2.82
3.16
4.29
5.00
1.70
2.21
2.78
3.48
4.10
1.54
1.81
2.27
2.86
3.29
4.54
1.43
1.78
2.26
2.64
3.72
4.40
1.45
1.91
2.18
3.00
3.48
4.73
1.40
1.83
2.21
2.83
3.67
4.72
1.16
1.54
1.83
2.29
2.89
3.63
4.51
1.13
1.44
1.70
2.37
2.81
3.92
4.32
0.91
1.22
1.40
1.91
2.21
3.03
3.62
4.78
0.89
1.17
1.37
1.81
2.27
3.01
3.35
4.56
4.91

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

113

3140

321

100

3530

361

90.0

3930

401

80.4

4400

449

72.0

4910

501

64.3

5500

561

57.1

6180

631

50.7

6970

711

45.0

7850

802

40.0

8830

902

36.0

9820

1000

Page of
Dimension Sheet

Model
SF

Size

Assembly

1.94
2.54
3.13
4.12
4.59
1.75
2.29
2.56
3.37
3.78
5.16
6.00
2.02
2.64
3.33
4.16
4.91
1.83
2.16
2.72
3.43
3.94
5.43
1.72
2.13
2.71
3.18
4.45
5.27
1.75
2.28
2.62
3.56
4.16
5.66
1.70
2.20
2.64
3.40
4.40
5.64
1.37
1.84
2.18
2.72
3.45
4.34
5.37
1.35
1.73
2.02
2.83
3.37
4.70
5.18
1.10
1.47
1.67
2.29
2.64
3.62
4.32
5.72
1.08
1.40
1.64
2.18
2.70
3.61
4.00
5.48
5.89

9030
9035
9040
9045
9050
9030
9035
9040
9045
9050
9055
9060
9035
9040
9045
9050
9055
9035
9040
9045
9050
9055
9060
9035
9040
9045
9050
9055
9060
9040
9045
9050
9055
9060
9065
9040
9045
9050
9055
9060
9065
9040
9045
9050
9055
9060
9065
9070
9040
9045
9050
9055
9060
9065
9070
9040
9045
9050
9055
9060
9065
9070
9075
9040
9045
9050
9055
9060
9065
9070
9075
9080

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P2
P3
P2
P2
P3
P2
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

37kW

Reduction
Ratio
16
16
16
16
16
18
18
18
18
18
18
18
20
20
20
20
20
22.4
22.4
22.4
22.4
22.4
22.4
25
25
25
25
25
25
28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
40
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-104
B-102
B-106
B-102
B-106
B-102
B-102
B-106
B-102
B-106
B-102
B-108
B-106
B-106
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-106
B-108
B-108
B-106
B-106
B-106
B-106
B-108
B-108
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-106
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-108

B - 89

SELECTION Drive Unit Parallel Shaft

37kW, 45kW

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

26.8

13190

1350

23.8

14840

1520

21.1

16730

1710

18.8

18850

1920

16.7

21200

2160

Drive Unit

Dimension Selection
Tables
Tables

45kW

SF
0.98
1.13
1.45
1.78
2.32
2.78
3.83
4.27
0.91
1.05
1.48
1.72
2.40
2.67
3.54
4.05
0.86
1.18
1.35
1.87
2.24
2.94
3.51
4.45
1.13
1.85
2.83
4.27
0.91
1.43
2.37
3.67

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

32.1

10990

1120

28.6

12370

1260

25.4

13940

1420

22.5

15700

1600

20.0

17670

1800

50Hz
4
1500

SF

Size

Assembly

1.18
1.35
1.75
2.13
2.78
3.32
4.59
5.10
1.09
1.27
1.78
2.08
2.88
3.21
4.21
4.83
1.05
1.43
1.62
2.23
2.67
3.54
4.18
5.32
1.35
2.23
3.37
5.10
1.08
1.71
2.83
4.37

9045
9050
9055
9060
9065
9070
9075
9080
9045
9050
9055
9060
9065
9070
9075
9080
9050
9055
9060
9065
9070
9075
9080
9085
9055
9065
9075
9085
9055
9065
9075
9085

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min
238
211

B - 90

188

2290

234

167

2580

263

150

2870

293

134

3210

328

120

3580

366

107

4010

410

SF
4.95
4.46
3.46
4.22
4.96
3.15
3.51
4.71
2.71
3.51
4.23
2.46
2.86
3.68
4.17
2.22
2.68
3.68
4.11
2.02
2.20
3.02
3.40
4.37

Output Speed
r/min
286
254

Reduction
Ratio
56
56
56
56
56
56
56
56
63
63
63
63
63
63
63
63
71
71
71
71
71
71
71
71
80
80
80
80
90
90
90
90

Vertical
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-108
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-108
B-106
B-106
B-108
B-108
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-106
B-108
B-108
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m
1800
184
2030
208

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m
1500
154
1700
173

225

1910

195

200

2150

219

180

2390

244

161

2670

273

144

2980

305

129

3340

341

Page of
Dimension Sheet

Model
SF

Size

Assembly

5.71
5.35
4.15
4.86
5.72
3.77
4.17
5.62
3.24
4.17
4.88
2.95
3.42
4.40
5.00
2.66
3.22
4.24
4.93
2.42
2.62
3.61
4.06
5.22

9040
9040
9035
9040
9045
9035
9040
9045
9035
9040
9045
9035
9040
9045
9050
9035
9040
9045
9050
9035
9040
9045
9050
9055

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2

Reduction
Ratio
6.3
7.1
8
8
8
9
9
9
10
10
10
11.2
11.2
11.2
11.2
12.5
12.5
12.5
12.5
14
14
14
14
14

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102

SELECTION Drive Unit Parallel Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

93.8

4580

468

83.3

5160

527

75.0

5730

585

67.0

6420

655

60.0

7160

731

53.6

8020

819

47.6

9020

921

42.3

10170

1040

37.5

11460

1170

33.3

12890

1320

30.0

14330

1460

SF
1.73
2.15
2.84
3.15
4.40
1.57
1.77
2.32
2.60
3.53
4.11
1.40
1.82
2.28
2.86
3.37
4.73
1.87
2.35
2.71
3.73
4.30
1.86
2.17
3.06
3.62
1.57
1.80
2.46
2.86
3.89
4.62
1.51
1.82
2.33
3.02
3.88
4.44
1.26
1.51
1.88
2.37
2.98
3.71
4.91
1.18
1.40
1.95
2.31
3.22
3.55
4.68
1.00
1.15
1.57
1.82
2.49
2.97
3.93
4.68
0.96
1.13
1.48
1.86
2.48
2.75
3.75
4.04

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

113

3820

390

100

4300

439

90.0

4780

488

80.4

5350

546

72.0

5970

609

64.3

6690

683

57.1

7520

768

50.7

8480

865

45.0

9550

975

40.0

10740

1100

36.0

11940

1220

Page of
Dimension Sheet

Model
SF

Size

Assembly

2.08
2.57
3.39
3.77
5.26
1.88
2.11
2.77
3.11
4.24
4.93
1.66
2.17
2.73
3.42
4.04
5.64
2.23
2.82
3.24
4.46
5.14
2.23
2.62
3.66
4.33
1.88
2.15
2.93
3.42
4.65
5.53
1.81
2.17
2.80
3.62
4.64
5.31
1.51
1.80
2.24
2.84
3.57
4.42
5.88
1.42
1.66
2.33
2.77
3.86
4.26
5.60
1.20
1.37
1.88
2.17
2.98
3.55
4.71
5.62
1.15
1.35
1.80
2.22
2.97
3.28
4.51
4.84

9035
9040
9045
9050
9055
9035
9040
9045
9050
9055
9060
9035
9040
9045
9050
9055
9060
9045
9050
9055
9060
9065
9045
9050
9055
9060
9045
9050
9055
9060
9065
9070
9045
9050
9055
9060
9065
9070
9045
9050
9055
9060
9065
9070
9075
9045
9050
9055
9060
9065
9070
9075
9045
9050
9055
9060
9065
9070
9075
9080
9045
9050
9055
9060
9065
9070
9075
9080

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P2
P3
P2
P3
P2
P3
P2
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

45kW

Reduction
Ratio
16
16
16
16
16
18
18
18
18
18
18
20
20
20
20
20
20
22.4
22.4
22.4
22.4
22.4
25
25
25
25
28
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
40
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-104
B-102
B-106
B-102
B-106
B-102
B-108
B-102
B-106
B-102
B-108
B-108
B-106
B-106
B-106
B-108
B-106
B-106
B-106
B-108
B-108
B-108
B-106
B-106
B-106
B-108
B-108
B-108
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-108
B-106
B-106
B-106
B-108
B-108
B-108
B-108
B-108

B - 91

SELECTION Drive Unit Parallel Shaft

45kW, 55kW

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

26.8

16040

1640

23.8

18050

1840

21.1

20340

2080

18.8

22920

2340

16.7

25790

2630

Drive Unit

Dimension Selection
Tables
Tables

55kW

SF
0.93
1.20
1.46
1.91
2.28
3.15
3.51
4.91
1.22
1.42
1.97
2.20
2.91
3.33
4.26
0.97
1.11
1.53
1.84
2.42
2.88
3.66
0.93
1.52
2.33
3.51
1.17
1.95
3.02

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

32.1

13370

1370

28.6

15040

1540

25.4

16950

1730

22.5

19100

1950

20.0

21490

2190

50Hz
4
1500

SF

Size

Assembly

1.11
1.44
1.75
2.28
2.73
3.77
4.20
5.86
1.46
1.71
2.36
2.64
3.46
3.97
5.11
1.17
1.33
1.84
2.20
2.91
3.44
4.37
1.11
1.83
2.77
4.20
1.40
2.33
3.60

9050
9055
9060
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9085
9055
9065
9075
9085
9065
9075
9085

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min
238
211

B - 92

188

2800

286

167

3150

322

150

3500

358

134

3920

400

120

4380

447

107

4900

501

93.8

5600

572

SF
4.05
3.65
3.45
4.06
4.92
2.87
3.85
4.34
2.87
3.46
4.10
4.92
2.34
3.01
3.41
4.54
2.20
3.01
3.36
4.10
1.80
2.47
2.78
3.58
4.40
2.32
2.58
3.60
4.27

Output Speed
r/min
286
254

Reduction
Ratio
56
56
56
56
56
56
56
56
63
63
63
63
63
63
63
71
71
71
71
71
71
71
80
80
80
80
90
90
90

Vertical
B-106
B-106
B-108
B-108
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-108
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m
2210
225
2490
254

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m
1840
188
2070
212

225

2330

238

200

2630

268

180

2920

298

161

3270

334

144

3650

372

129

4090

417

113

4670

477

Page of
Dimension Sheet

Model
SF

Size

Assembly

4.67
4.38
3.98
4.68
5.65
3.41
4.60
5.20
3.41
3.99
470
5.65
2.80
3.60
4.09
5.43
2.63
3.47
4.03
4.70
2.14
2.95
3.32
4.27
5.25
2.77
3.09
4.30
5.10

9040
9040
9040
9045
9050
9040
9045
9050
9040
9045
9050
9055
9040
9045
9050
9055
9040
9045
9050
9055
9040
9045
9050
9055
9060
9045
9050
9055
9060

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2

Reduction
Ratio
6.3
7.1
8
8
8
9
9
9
10
10
10
10
11.2
11.2
11.2
11.2
12.5
12.5
12.5
12.5
14
14
14
14
14
16
16
16
16

Vertical
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-102
B-104
B-102
B-102
B-102
B-104

SELECTION Drive Unit Parallel Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

83.3

6300

644

75.0

7000

715

67.0

7840

801

60.0

8750

894

53.6

9800

1000

47.6

11030

1130

42.3

12430

1270

37.5

14010

1430

33.3

15760

1610

30.0

17510

1790

26.8

19610

2000

23.8

22060

2250

SF
1.90
2.12
2.89
3.36
4.59
1.87
2.34
2.76
3.87
4.57
1.53
1.92
2.21
3.05
3.52
4.72
2.50
2.96
4.12
4.54
2.01
2.34
3.18
3.78
5.00
1.90
2.47
3.17
3.63
4.80
1.54
1.94
2.44
3.03
4.01
4.67
1.60
1.89
2.63
2.90
3.83
4.43
1.29
1.49
2.04
2.43
3.21
3.83
4.89
1.21
1.52
2.03
2.25
3.07
3.30
0.98
1.20
1.56
1.87
2.58
2.87
4.01
1.16
1.61
1.80
2.38
2.72
3.49

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

100

5250

536

90.0

5840

596

80.4

6540

667

72.0

7300

745

64.3

8170

834

57.1

9190

938

50.7

10360

1060

45.0

11670

1190

40.0

13130

1340

360

14590

1490

32.1

16340

1670

28.6

18380

1880

Page of
Dimension Sheet

Model
SF

Size

Assembly

2.27
2.54
3.47
4.03
5.48
2.24
2.80
3.30
4.61
5.46
1.83
2.30
2.65
3.65
4.21
5.63
3.00
3.54
4.76
5.43
2.40
2.80
3.81
4.52
5.98
2.29
2.96
3.79
4.34
5.72
1.83
2.32
2.92
3.61
4.81
5.58
1.90
2.27
3.16
3.49
4.58
5.30
1.54
1.78
2.44
2.90
3.85
4.59
5.83
1.47
1.81
2.43
2.69
3.69
3.96
1.18
1.43
1.87
2.23
3.09
3.43
4.80
1.40
1.93
2.16
2.83
3.25
4.18

9045
9050
9055
9060
9065
9045
9050
9055
9060
9065
9045
9050
9055
9060
9065
9070
9055
9060
9065
9070
9055
9060
9065
9070
9075
9055
9060
9065
9070
9075
9055
9060
9065
9070
9075
9080
9055
9060
9065
9070
9075
9080
9055
9060
9065
9070
9075
9080
9085
9055
9060
9065
9070
9075
9080
9055
9060
9065
9070
9075
9080
9085
9060
9065
9070
9075
9080
9085

P2
P2
P2
P2
P2
P2
P3
P2
P3
P2
P2
P3
P2
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

55kW

Reduction
Ratio
18
18
18
18
18
20
20
20
20
20
22.4
22.4
22.4
22.4
22.4
22.4
25
25
25
25
28
28
28
28
28
31.5
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5
35.5
40
40
40
40
40
40
45
45
45
45
45
45
45
50
50
50
50
50
50
56
56
56
56
56
56
56
63
63
63
63
63
63

Vertical
B-102
B-102
B-102
B-104
B-104
B-102
B-106
B-102
B-108
B-104
B-102
B-106
B-102
B-108
B-104
B-108
B-106
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-108
B-106
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108

B - 93

SELECTION Drive Unit Parallel Shaft

55kW, 75kW

Frequency
Output Speed
r/min

Drive Unit

Dimension Selection
Tables
Tables

50Hz
Output Torque (Tout)
Nm
kgf m

21.1

24860

2540

18.8

28010

2860

16.7

31520

3220

75kW

SF
0.90
1.25
1.50
1.98
2.36
3.00
1.24
1.90
2.87
0.96
1.60
2.47

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

25.4

20720

2120

22.5

23340

2380

20.0

26260

2680

50Hz
4
1500

SF

Size

Assembly

1.09
1.50
1.80
2.38
2.81
3.58
1.50
2.27
3.43
1.15
1.90
2.94

9060
9065
9070
9075
9080
9085
9065
9075
9085
9065
9075
9085

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min
238
211
188

B - 94

167

4300

439

150

4780

488

134

5350

546

120

5970

609

107

6690

683

93.8

7640

780

83.3

8600

878

75.0

9550

975

67.0

10700

1090

60.0

11940

1220

53.6

13370

1370

47.6

15040

1540

42.3

16950

1730

SF
4.06
3.90
4.06
4.06
4.94
3.61
3.33
4.01
3.01
4.09
2.62
3.22
4.19
2.64
3.13
4.37
4.90
2.12
2.46
3.36
4.10
2.02
2.84
3.35
4.13
1.62
2.24
2.58
3.46
4.34
3.02
3.33
4.13
2.33
2.77
3.66
4.40
2.32
2.66
3.52
3.96
1.79
2.22
2.94
3.42
4.61

Output Speed
r/min
286
254
225

Reduction
Ratio
71
71
71
71
71
71
80
80
80
90
90
90

Vertical
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m
3010
307
3390
346
3820
390

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m
2510
256
2830
288
3180
325

200

3580

366

180

3980

406

161

4460

455

144

4970

508

129

5570

569

113

6370

650

100

7160

731

90.0

7960

813

80.4

8910

910

72.0

9950

1020

64.3

11140

1140

57.1

12530

1280

50.7

14130

1440

Page of
Dimension Sheet

Model
SF

Size

Assembly

4.66
4.65
4.66
4.66
5.90
4.14
3.98
4.80
3.45
4.88
3.13
3.85
5.00
3.16
3.74
5.19
5.86
2.54
2.96
4.02
4.90
2.42
3.38
4.01
4.74
1.94
2.68
3.08
4.13
5.20
3.49
3.98
4.74
2.79
3.32
4.38
5.26
2.78
3.18
4.20
4.73
2.14
2.65
3.53
4.09
5.50

9050
9050
9055
9055
9060
9055
9055
9060
9055
9060
9055
9060
9065
9055
9060
9065
9070
9055
9060
9065
9070
9055
9060
9065
9070
9055
9060
9065
9070
9075
9065
9070
9075
9065
9070
9075
9080
9065
9070
9075
9080
9065
9070
9075
9080
9085

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P2
P3
P2
P3
P2
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Reduction
Ratio
6.3
7.1
8
9
9
10
11.2
11.2
12.5
12.5
14
14
14
16
16
16
16
18
18
18
18
20
20
20
20
22.4
22.4
22.4
22.4
22.4
25
25
25
28
28
28
28
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
35.5

Vertical
B-102
B-102
B-102
B-102
B-104
B-102
B-102
B-104
B-102
B-104
B-102
B-104
B-104
B-102
B-104
B-104
B-104
B-102
B-104
B-104
B-104
B-102
B-108
B-104
B-108
B-102
B-108
B-104
B-108
B-104
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108

SELECTION Drive Unit Parallel Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

37.5

19100

1950

33.3

21490

2190

30.0

23880

2440

26.8

26740

2730

23.8

30080

3070

21.1

33900

3460

18.8

38200

3900

16.7

42980

4390

90kW

SF
1.93
2.13
2.81
3.25
4.17
1.49
1.78
2.36
2.81
3.58
1.48
1.65
2.25
2.42
3.42
1.37
1.89
2.10
2.94
1.32
1.74
2.00
2.56
1.10
1.45
1.73
2.20
1.40
2.10
1.17
1.81

Frequency Hz
Pole
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

45.0

15920

1630

40.0

17910

1830

36.0

19900

2030

32.1

22280

2280

28.6

25070

2560

25.4

28250

2880

22.5

31830

3250

20.0

35810

3660

50Hz
4
1500

Output Speed
r/min
188
167

5160

527

150

5730

582

134

6420

655

120

7160

731

107

8020

819

93.8

9170

936

83.3

10310

1050

75.0

11460

1170

SF
3.38
3.38
4.12
4.24
2.77
3.34
4.30
3.41
4.42
2.68
3.49
4.25
2.61
3.64
4.08
2.05
2.80
3.42
4.51
2.79
3.44
4.32

Output Speed
r/min
225

Page of
Dimension Sheet

Model
SF

Size

Assembly

2.32
2.56
3.36
3.89
4.98
1.78
2.13
2.82
3.37
4.28
1.78
1.97
2.70
2.90
4.10
1.64
2.26
2.52
3.52
1.58
2.08
2.38
3.06
1.32
1.74
2.06
2.62
1.66
2.52
1.40
2.16

9065
9070
9075
9080
9085
9065
9070
9075
9080
9085
9065
9070
9075
9080
9085
9070
9075
9080
9085
9070
9075
9080
9085
9070
9075
9080
9085
9075
9085
9075
9085

P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Reduction
Ratio
40
40
40
40
40
45
45
45
45
45
50
50
50
50
50
56
56
56
56
63
63
63
63
71
71
71
71
80
80
90
90

Vertical
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m
4580
468

75kW, 90kW

60Hz
Output Torque (Tout)
Nm
kgf m
3820
390

200

4300

439

180

4780

488

161

5350

546

144

5970

609

129

6690

683

113

7640

780

100

8600

878

90.0

9550

975

Page of
Dimension Sheet

Model
SF

Size

Assembly

3.88
3.88
4.92
5.02
3.32
4.00
5.13
4.06
5.02
3.21
4.17
5.07
3.12
4.33
4.88
2.46
3.35
4.08
5.38
3.34
3.95
5.16

9055
9055
9060
9060
9055
9060
9065
9060
9065
9060
9065
9070
9060
9065
9070
9060
9065
9070
9075
9065
9070
9075

P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P3
P2

Reduction
Ratio
8
9
9
10
11.2
11.2
11.2
12.5
12.5
14
14
14
16
16
16
18
18
18
18
20
20
20

Vertical
B-102
B-102
B-104
B-104
B-102
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-108
B-104

B - 95

SELECTION Drive Unit Parallel Shaft

90kW, 110kW

Frequency
Output Speed
r/min

Drive Unit

Dimension Selection
Tables
Tables

50Hz
Output Torque (Tout)
Nm
kgf m

67.0

12840

1310

60.0

14330

1460

53.6

16040

1640

47.6

18050

1840

42.3

20340

2080

37.5

22920

2340

33.3

25790

2630

30.0

28650

2930

26.8

32090

3280

23.8

36100

3690

21.1

40680

4150

18.8

45840

4680

16.7

51570

5270

SF
2.15
2.88
3.62
4.45
2.77
3.44
4.24
2.31
3.05
3.66
4.66
2.22
2.93
3.30
4.46
1.85
2.45
2.85
3.84
1.77
2.34
2.71
3.47
1.48
1.96
2.34
2.98
1.87
2.02
2.85
1.57
1.75
2.45
1.45
1.66
2.13
1.21
1.44
1.83
1.16
1.75
0.97
1.51

Frequency

Hz
P
5RGGFn1 r/min

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

80.4

10700

1090

72.0

11940

1220

64.3

13370

1370

57.1

15040

1540

50.7

16950

1730

45.0

19100

1950

40.0

21490

2190

36.0

23880

2440

32.1

26740

2730

28.6

30080

3070

25.4

33900

3460

22.5

38200

3900

20.0

42980

4390

50Hz
4
1500

110kW Pole

SF

Size

Assembly

2.57
3.44
4.33
5.33
3.32
3.95
5.06
2.76
3.65
4.38
5.57
2.65
3.50
3.94
5.34
2.21
2.94
3.41
4.58
2.13
2.80
3.24
4.15
1.77
2.35
2.81
3.56
2.25
2.42
3.42
1.88
2.10
2.93
1.73
1.98
2.55
1.45
1.72
2.18
1.38
2.10
1.16
1.80

9065
9070
9075
9080
9070
9075
9080
9070
9075
9080
9085
9070
9075
9080
9085
9070
9075
9080
9085
9070
9075
9080
9085
9070
9075
9080
9085
9075
9080
9085
9075
9080
9085
9075
9080
9085
9075
9080
9085
9075
9085
9075
9085

P2
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

Output Speed
r/min
167
150

B - 96

134

7840

801

120

8750

894

107

9800

1000

SF

Output Speed
r/min

4.44
4.13
3.51
4.50
3.62
4.16
2.85
3.48
4.78

161
144

Reduction
Ratio
22.4
22.4
22.4
22.4
25
25
25
28
28
28
28
31.5
31.5
31.5
31.5
35.5
35.5
35.5
35.5
40
40
40
40
45
45
45
45
50
50
50
56
56
56
63
63
63
71
71
71
80
80
90
90

Vertical
B-104
B-108
B-104
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108

60Hz
4
1800

Frequency
50Hz
Output Torque (Tout)
Nm
kgf m
6310
644
7010
715

Page of
Dimension Sheet

Model

60Hz
Output Torque (Tout)
Nm
kgf m
5260
536
5840
596

161

6540

667

144

7300

745

129

8170

834

Page of
Dimension Sheet

Model
SF

Size

Assembly

Reduction
Ratio

Vertical

5.30
4.70
4.20
5.38
4.11
4.97
3.41
4.15
5.70

9065
9065
9065
9070
9065
9070
9065
9070
9075

P2
P2
P2
P2
P2
P2
P2
P2
P2

9
10
11.2
11.2
12.5
12.5
14
14
14

B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-104

SELECTION Drive Unit Parallel Shaft

Frequency
Output Speed
r/min

50Hz
Output Torque (Tout)
Nm
kgf m

93.8

11210

1140

83.3

12610

1290

75.0

14010

1430

67.0

15690

1600

60.0

17510

1790

53.6

19610

2000

47.6

22060

2250

42.3

24860

2540

37.5

28010

2860

33.3

31520

3220

30.0

35020

3580

26.8

39220

4000

23.8
21.1
18.8
16.7

44120
49720
56030
63030

4500
5080
5720
6440

SF
2.98
3.34
4.40
2.80
3.69
4.37
3.53
4.20
2.96
3.64
4.57
2.81
3.47
4.43
2.50
3.00
3.81
2.40
2.70
3.65
2.00
2.33
3.14
1.91
2.21
2.84
1.60
1.91
2.44
1.65
2.33
1.43
2.00
1.74
1.50
1.43
1.23

Output Speed
r/min

60Hz
Output Torque (Tout)
Nm
kgf m

113

9340

953

100

10510

1070

90.0

11670

1190

80.4

13070

1330

72.0

14590

1490

64.3

16340

1670

57.1

18380

1880

50.7

20720

2120

45.0

23340

2380

40.0

26260

2680

36.0

29180

2980

32.1

32680

3340

28.6
25.4
22.5
20.0

36770
41440
46690
52530

3750
4230
4770
5360

110kW

Page of
Dimension Sheet

Model
SF

Size

Assembly

Reduction
Ratio

Vertical

3.54
4.00
5.13
3.34
4.40
5.21
4.22
5.03
3.54
4.36
5.46
3.23
4.14
5.20
2.99
3.59
4.56
2.86
3.22
4.37
2.40
2.79
3.75
2.29
2.65
3.40
1.92
2.29
2.91
1.98
2.80
1.71
2.40
2.09
1.79
1.71
1.47

9065
9070
9075
9070
9075
9080
9075
9080
9075
9080
9085
9075
9080
9085
9075
9080
9085
9075
9080
9085
9075
9080
9085
9075
9080
9085
9075
9080
9085
9080
9085
9080
9085
9085
9085
9085
9085

P2
P2
P2
P2
P2
P2
P2
P3
P2
P3
P2
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3

16
16
16
18
18
18
20
20
22.4
22.4
22.4
25
25
25
28
28
28
31.5
31.5
31.5
35.5
35.5
35.5
40
40
40
45
45
45
50
50
56
56
63
71
80
90

B-104
B-104
B-104
B-104
B-104
B-104
B-104
B-108
B-104
B-108
B-104
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108
B-108

B - 97

SELECTION Drive Unit

Allowable Radial and Axial Loads on Slow Speed Shaft

Allowable Radial Load (kN)

Sheet 1

Drive Unit

Dimension Selection
Tables
Tables

L.Speed
Size of Reducer
Shaft
Speed
r/min 9015 9025 9030 9035 9040 9045 9050 9055 9060 9065
250 11.8 17.7 17.7 29.4 29.9 32.4 37.8 46.6 39.7 49.1
160 11.8 17.7 20.1 31.4 32.4 33.8 39.7 48.1 41.7 50.5
Standard 100 11.8 17.7 25.0 35.3 38.7 39.2 47.1 53.5 47.6 54.4
bearing
63 11.8 17.7 26.5 35.3 42.2 47.1 54.9 62.3 58.9 64.3
model
40 11.8 17.7 26.5 35.3 42.2 49.1 54.9 67.7 71.1 78.0
25 11.8 17.7 26.5 35.3 42.2 49.1 54.9 67.7 81.4 95.2
250
71.1 93.7
160
78.0 94.7
Heavy
81.4 98.1
duty 100
bearing 63
81.4 98.1
model
40
81.4 98.1
81.4 98.1
25

Sheet 2

Applicable to congurations: RML

9070
44.1
46.1
54.4
65.2
79.0
99.1
70.1
77.5
92.2
114.8
117.7
117.7

9075
77.0
89.0
99.0
131.5
141.0
139.5
122.5
137.5
149.5
149.0
148.5
147.0

9080
77.0
89.0
99.0
131.5
141.0
139.5
122.5
137.5
149.5
149.0
148.5
147.0

9085
100.1
108.9
122.1
125.6
125.1
122.6
141.8
132.4
127.0
125.6
125.1
122.6

Applicable to congurations: RMR

L.Speed
Size of Reducer
Shaft
Speed
r/min 9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085
250
8.3
15.2
9.8
21.6 19.1 21.6 22.6 31.4 16.7 28.4 17.2 44.0 44.0 58.4
160
9.8
17.7 12.3 23.1 20.6 23.1 24.0 31.4 18.1 27.0 17.7 55.5 55.5 64.3
Standard
bearing 100 11.8 17.7 16.7 29.4 26.0 27.5 28.4 35.3 22.1 30.4 25.5 63.5 63.5 74.6
model
63 11.8 17.7 21.6 35.3 32.9 35.3 37.3 42.7 33.4 38.3 33.8 95.0 95.0 104.5
40 11.8 17.7 26.5 35.3 41.7 43.7 48.6 55.4 45.1 51.5 47.6 129.0 129.0 146.7
25 11.8 17.7 26.5 35.3 42.2 49.1 61.6 67.7 60.8 68.7 67.7 167.0 167.0 171.2
250
46.1 74.6 40.2 90.0 90.0 114.8
52.0 72.1 45.6 103.5 103.5 125.1
Heavy 160
duty 100
60.3 79.1 59.4 116.0 116.0 140.8
bearing
63
81.4 96.6 80.0 152.5 152.5 174.1
model
40
81.4 98.1 108.9 192.0 192.0 191.8
81.4 98.1 117.7 180.5 180.5 171.2
25

Allowable Axial Load (kN)

L.Speed
Size of Reducer
Shaft
Speed
r/min 9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085
250
9.3
11.4 14.7 23.1 26.5 31.4 32.9 31.9 27.0 43.2 28.0 28.0 23.5 23.5
160
9.3
11.4 18.1 23.1 28.4 31.4 33.4 31.9 28.9 43.2 28.4 28.4 27.5 27.5
Standard 100
9.3
11.4 24.5 23.1 32.9 31.4 37.3 31.9 34.3 43.2 39.7 39.7 32.9 32.9
bearing
63
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 52.5 52.5 45.6 45.6
model
40
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 61.4 61.4 63.3 60.3
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 61.4 61.4 67.7 60.3
25
250
23.1 34.8 18.6 18.6 56.9 56.9
160
25.0 33.4 21.1 21.1 56.9 56.9
Heavy
100
29.4 36.8 27.5 27.5 56.9 56.9
duty
bearing
63
39.2 43.2 36.3 36.3 56.9 56.9
model
40
39.2 43.2 49.1 49.1 56.9 56.9
39.2 43.2 56.9 56.9 56.9 56.9
25

B - 98

 Parallel

SELECTION Drive Unit

Allowable Radial and Axial Loads on Slow Speed Shaft

Overhang Factor
Overhang Member
Sprocket (Single Row)
Sprocket (Double Row)
Gears

Overhang Factor
1
1.25
1.25

Notes
1. The value shown in the table is allowable radial
load when it is applied to the center of the solid
shaft (except hollow shaft).
Consult us when a load is not in the center.
2. Consult us for the blanks in the table.
3. Consult us when the radial load is applied
upward.
4. In case of double projection shaft
(RMB,LMB,BMB)
(1) See sheet1 when the radial load is applied
only to the shaft1.
(2) See sheet2 when the radial load is applied
only to the shaft2.
(3) Consult us when the radial load is applied to
both shafts.
5. Refer to B-6 to check overhang load, and
calculate equivalent load at peak load value.
Be careful under following condition because
large peak load may be generated.
Application: When the inertia is large, such as
for crane driving, slewing, etc.
Motor: inline motor
Connecting method: Sprocket or gear
Consult us when the peak load is larger than
allowable value.

RB

LB

1
1

2
BB

B - 99

SELECTION Drive Unit

Allowable Radial and Axial Loads on Slow Speed Shaft

Allowable Radial Load (kgf)

Sheet 1

Drive Unit

Dimension Selection
Tables
Tables

L.Speed
Shaft
Speed
r/min
250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
duty 100
bearing 63
model
40
25

Applicable to congurations: RML

Size of Reducer
9015
1200
1200
1200
1200
1200
1200

9025
1800
1800
1800
1800
1800
1800

9030
1800
2050
2550
2700
2700
2700

9035
3000
3200
3600
3600
3600
3600

9040
3050
3300
3950
4300
4300
4300

9045
3300
3450
4000
4800
5000
5000

9050
3850
4050
4800
5600
5600
5600

9055
4750
4900
5450
6350
6900
6900

9060
4050
4250
4850
6000
7250
8300
7250
7950
8300
8300
8300
8300

9065
5000
5150
5550
6550
7950
9700
9550
9650
10000
10000
10000
10000

9070
4500
4700
5550
6650
8050
10100
7150
7900
9400
11700
12000
12000

9075
7850
9050
10100
13400
14350
14200
12500
14000
15250
15200
15150
15000

Sheet 2
L.Speed
Shaft
Speed
r/min
250
160
Standard
bearing 100
model
63
40
25
250
Heavy 160
duty 100
bearing
63
model
40
25

9080
7850
9050
10100
13400
14350
14200
12500
14000
15250
15200
15150
15000

9085
10200
11100
12450
12800
12750
12500
14450
13500
12950
12800
12750
12500

Applicable to congurations: RMR

Size of Reducer
9015
850
1000
1200
1200
1200
1200

9025
1550
1800
1800
1800
1800
1800

9030
1000
1250
1700
2200
2700
2700

9035
2200
2350
3000
3600
3600
3600

9040
1950
2100
2650
3350
4250
4300

9045
2200
2350
2800
3600
4450
5000

9050
2300
2450
2900
3800
4950
5600

9055
3200
3200
3600
4350
5650
6900

9060
1700
1850
2250
3400
4600
6200
4700
5300
6150
8300
8300
8300

9065
2900
2750
3100
3900
5250
7000
7600
7350
8050
9850
10000
10000

9070
1750
1800
2600
3450
4850
6900
4100
4650
6050
8150
11100
12000

9075
4500
5650
6450
9700
13150
17000
9150
10550
11800
15550
19550
18400

9080
4500
5650
6450
9700
13150
17000
9150
10550
11800
15550
19550
18400

9085
5950
6550
7600
10650
14950
17450
11700
12750
14350
17750
19550
17450

9070
2850
2900
4050
5350
6260
6260
1900
2150
2800
3700
5000
5800

9075
2850
2900
4050
5350
6260
6260
1900
2150
2800
3700
5000
5800

9080
2400
2800
3350
4650
6450
6900
5800
5800
5800
5800
5800
5800

9085
2400
2800
3350
4650
6150
6150
5800
5800
5800
5800
5800
5800

Allowable Axial Load (kgf)

L.Speed
Shaft
Speed
r/min 9015 9025
250 950 1160
160 950 1160
Standard 100
950 1160
bearing
63 950 1160
model
40 950 1160
25 950 1160
250
160
Heavy
100
duty
bearing
63
model
40
25

B - 100

Size of Reducer
9030
1500
1850
2500
2700
2700
2700

9035
2350
2350
2350
2350
2350
2350

9040
2700
2900
3350
3350
3350
3350

9045
3200
3200
3200
3200
3200
3200

9050
3350
3400
3800
3800
3800
3800

9055
3250
3250
3250
3250
3250
3250

9060
2750
2950
3500
5000
5000
5000
2350
2550
3000
4000
4000
4000

9065
4400
4400
4400
4400
4400
4400
3550
3400
3750
4400
4400
4400

SELECTION Drive Unit

Allowable Radial and Axial Loads on Slow Speed Shaft

Overhang Factor
Overhang Member
Sprocket (Single Row)
Sprocket (Double Row)
Gears

Overhang Factor
1
1.25
1.25

Notes
1. The value shown in the table is allowable radial
load when it is applied to the center of the solid
shaft (except hollow shaft).
Consult us when a load is not in the center.
2. Consult us for the blanks in the table.
3. Consult us when the radial load is applied
upward.
4. In case of double projection shaft
(RMB,LMB,BMB)
(1) See sheet1 when the radial load is applied
only to the shaft1.
(2) See sheet2 when the radial load is applied
only to the shaft2.
(3) Consult us when the radial load is applied to
both shafts.
5. Refer to B-6 to check overhang load, and
calculate equivalent load at peak load value.
Be careful under following condition because
large peak load may be generated.
Application: When the inertia is large, such as
for crane driving, slewing, etc.
Motor: inline motor
Connecting method: Sprocket or gear
Consult us when the peak load is larger than
allowable value.

RB

LB

1
1

2
BB

B - 101

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

9015 9055

MB
MD

MA

H
L

N1

N2

MC

NP

C1

Drive Unit

B
DP1

E1

Dimension Selection
Tables
Tables

E2

E3

K
Y

G
DP2

4- J
G

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

TU2

U4

V2

X1

Refer to the page D -18 for details.

W1

Refer to the page D -18 for details.

Standard Shaft Arrangement Conguration

RML

RMR

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996) Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions not shown in these drawings.

B - 102

T4

Z1

Y1

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

V5

Solid Shaft

4. Refer to the page D -25 for the dimension of optional parts.

5. Refer to the page D-33 for motor terminal box position.
6. Refer to the page D-34 for ange dimension.

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

H

35 80 15
40 87.5 19
50 105 24
50 120 24
60 128 28
60 140 28
60 140 28
60 155 28

RI

T1

U1

V1

W1/Depth

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110
140
170
170
170
210
210
210

58m6
70m6
80m6
90m6
95m6
105m6
110m6
120m6

M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

P V A

Shaft
Arrangement

P 2 9015
9025
9030
9035
9040
9045
9050
9055

N1

186 25
198.5 23
211 22
211 22
237.5 15
237.5 17.5
257.5 23
257.5 23

C
MD

9015 9025 9030 9035 9040 9045 9050

144
185
188
232
297
297
297
297
297
412
485
485

397.5
397.5
427.5
427.5
427.5
427.5

427.5
457.5
457.5
457.5
457.5
457.5
487.5

515.5
515.5
515.5
515.5
515.5
545.5

515.5
515.5
515.5
515.5
545.5
545.5

555.5
555.5
555.5
585.5
585.5
585.5

555.5
555.5
555.5
585.5
585.5
585.5

Hollow Shaft (Shrink Disk Type)

TU1

Size

M
70
75
85
100
100
120
110
135

N2

NP

14
12
9
9
2
2
7
7

100
100
100
100
117
117
117
117

230
270
270
320
340
380
360
430

102.5
117.5
132.5
132.5
157.5
157.5
172.5
172.5

260
310
365
396
420
459
490
529

Key
Y1 Z1
7
11
7.5 12
9
14
9
14
9
14
10 16
10 16
11 18

X1
18
20
22
25
25
28
28
32

Low Speed
Shaft
Type

L1
95
125
150
150
150
190
190
185

Hollow Shaft (Key Type)

TU2 T2

U2

328
358
393
403
448
463
503
528

135 63 60 270
145 73 70 300
160 83 80 330
160 88 85 330
180 98 95 360
180 108 105 370
200 108 105 410
205 123 120 410

193
213
233
243
268
283
303
323

V2

589.5
619.5
619.5
619.5
619.5

Mass of Motor Mass of Motor (kg)

Mounting
9055 Flange (kg) Without With
Brake Btake
8
43
54
8
57
77
11
76
96
11
131 175
17
213 258
17
213 258
589.5
17
224 280
619.5
15
259 320
619.5
15
259 320
619.5
29
276
619.5
31
490
619.5
31
540

Motor
With Brake
MA
MB
MC
454 212 315
510 251 315
575 251 350
700 324 350
835 394 400
835 394 400
835 394 400
930.5 394 450
930.5 394 450

Nomenclature

L
440
505
590
640
685
745
775
845

9015
9025
9030
9035
9040
9045
9050
9055

K
95
110
120
120
150
150
150
150

*) Mass of drive unit with motor, add mass of motor ange

and mass of motor, shown in table below.

Solid Shaft

Size

G
20
20
25
25
30
30
30
30

E1

E3
135
155
160
185
200
220
210
245

Without Brake
MA MG
MC
382 212 315
415 251 315
480 251 350
545 324 350
625 394 400
625 394 400
625 394 400
715.5 394 450
715.5 394 450
769.5 484 550
799 490 545
799 490 545

Double
Reduction

5.5
7.5
11
15
18.5
22
30
37
45
55
75
90

Parallel

DP1 DP2 Oil(L)Oty Wt. (kg)*)

3/4" 3/4" 5
125
3/4" 3/4" 7
170
3/4" 3/4" 9
235
3/4" 3/4" 12
255
1"
1"
18
345
1"
1"
22
405
1"
1"
22
485
1"
1"
31
550

kW

C1

9015
9055

Size
9015
9025
9030
9035
9040
9045
9050
9055

E2

194
140 270 195
227
155 310 215
264
175 320 220
295 See 194 370 245
306 below 205 400 260
345
226 440 266
358
225 420 270
397
256 490 305

Monoblock

B
160
175
200
219
235
256
255
286

Vertical

A
295
346
406
437
467
506
537
576

PARAMAX

Size
9015
9025
9030
9035
9040
9045
9050
9055

9015 9055

V3 TU4 T4
135
150
165
165
180
185
205
205

U4

V4

V5

135 55 55
150 65 65
165 75 75
165 85 85
180 90 90
185 105 105
205 105 105
205 115 115
Unit: mm

Nominal
Reduction Ratio

RML
RMR

Size

(blank) : Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

6.3

7.1

10

14

16

18

9015

9025

9030

9035
9040

9045
9050
9055

11.2 12.5

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 103

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

9060 9085

MB

N1

MA

P1

MD

MC

NP

DP1

Drive Unit

RI

E1

Dimension Selection
Tables
Tables

C1

E2

K
G

K
D

DP2

E3

4- J
G

L
* Refer to footnote 3.

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

TU2

U4

V2

X1

T4

Z1

Y1

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

Refer to the page D -18 for details.

W1

Refer to the page D -18 for details.

Standard Shaft Arrangement Conguration

RML

RMR

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996) Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RMR is equipped with oil gauge. Refer to the page D-28.

B - 104

V5

Solid Shaft

4.
5.
6.
7.

Refer to the page D-14 for dimensions not shown in these drawings.
Refer to the page D -28 for the dimension of optional parts.
Refer to the page D-33 for motor terminal box position.
Refer to the page D-34 for ange dimension.

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

H

RI

N1

NP

P1

251 530
414
460
290 600
482 See 283 600
535 below 330 670
556
325 670
612
369 750

282
317
317
352
352
392

265
300
300
335
335
375

35
35
40
40
40
40

35
35
40
52
52
52

160
175
175
160
190
215

35
35
42
42
42
42

180
180
215
220
220
220

885
970
1020
1120
1155
1255

140
175
155
195
170
210

277.5
277.5
302.5
302.5
322.5
322.5

35
38
38
40
45
40

117
117
117
117
117
117

460
530
520
590
590
670

190
190
215
215
230
230

223
223
253
253
283
283

564
610
657
710
750
806

*) Mass of drive unit with motor, add mass of motor ange

and mass of motor, shown in table below.

Motor
With Brake
MA MB MC
930.5 394 450
930.5 394 450

Mass of Motor Mass of Motor (kg)

Mounting
With
9060 9065 9070 9075 9080 9085 Flange (kg) Without
Brake Btake

MD
297
297
412
485
485
515

694
694
694
694
694

694
694
694
694
694
724

Solid Shaft

Size
9060
9065
9070
9075
9080
9085

744
744
774

744
744
774

838

15
15
29
31
31
56

838

Hollow Shaft (Shrink Disk Type)

TU1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

Key
Y1 Z1
11 18
12 20
12 20
13 22
13 22
15 25

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

259
259
276
490
540
675

320
320

Hollow Shaft (Key Type)

TU2 T2

U2

V2

V3 TU4 T4

U4

V4

V5

583
594
644
651
714
714

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

353
359
384
386
429
429

DP1 DP2 Oil(L)Oty Wt. (kg)*)

1"
1"
25
705
1"
1"
32
830
1"
1"
39
985
1"
1"
49
1245
1"
1"
54
1380
1"
1"
71
1650

Size

E3

E2

Double
Reduction

299
338
336
383
378
422

37
45
55
75
90
110

E1

Without Brake
MA MG
MC
715.5 394
450
715.5 394
450
769.5 484
550
799 490
545
799 490
545
898 550
655

Parallel

621
667
719
772
812
868

kW

9060
9085

9060
9065
9070
9075
9080
9085

9060
9065
9070
9075
9080
9085

C1

Split

Vertical

PARAMAX

Size

9060 9085

470
480
530
530
570
570

235
240
265
265
285
285

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P V D

P 2 9060
9065
9070
9075
9080
9085

Low Speed
Shaft
Type

Nominal
Reduction Ratio

RML
RMR

Size

(blank): Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9060

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9065
9070
9075
9080
9085

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 105

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

9015 9055

MB
MD

MA

H
L

N1

MC
NP

194 (9015 Only)

C

C1

Drive Unit

DP2

M2

E1

M1

Dimension Selection
Tables
Tables

E2

RI

M1

DP1

E3

4- J
G

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

TU2

U4

V2

X1

Refer to the page D -18 for details.

W1

Refer to the page D -18 for details.

Standard Shaft Arrangement Conguration

RML

RMR

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996) Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-13 for dimensions not shown in these drawings.

B - 106

T4

Z1

Y1

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

V5

Solid Shaft

4. Refer to the page D -25 for the dimension of optional parts.

5. Refer to the page D-33 for motor terminal box position.
6. Refer to the page D-34 for ange dimension.

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

G

257
140 270 195
306
155 310 215
343
175 320 220
374 See 194 370 245
398 below 205 400 260
437
226 440 277
467
225 420 270
506
256 490 305

135
155
160
185
200
220
210
245

20
20
25
25
28
30
30
30

35 80 15
40 87.5 19
50 105 24
50 120 24
60 120 28
60 140 28
60 140 28
60 155 28

9015
9025
9030
9035
9040
9045
9050
9055

Motor
Without Brake
With Brake
MA MG MC
MA
MB
MC
382 212 315 454 212 315
415 251 315 510 251 315
480 251 350 575 251 350
545 324 350 700 324 350
625 394 400 835 394 400
625 394 400 835 394 400
625 394 400 835 394 400
715.5 394 450 930.5 394 450
715.5 394 450 930.5 394 450
769.5 484 550

T1

U1

V1

W1/Depth

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110
140
170
170
170
210
210
210

58m6
70m6
80m6
90m6
95m6
105m6
110m6
120m6

M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50
Shaft
Arrangement

Size

P V A

P 3 9015
9025
9030
9035
9040
9045
9050
9055

M1

95
110
120
120
150
150
150
150

485
570
640
690
759
819
848
918

M2

70 80
75 90
85 50
100 75
100 70
120 90
110 83
135 118

N1

NP

186 25 100 230

198.5 23 100 270
211 22 100 270
211 22 100 320
228.5 15 100 340
228.5 17.5 100 380
248.5 23 100 360
248.5 23 100 430

102.5
117.5
132.5
132.5
157.5
157.5
172.5
172.5

305
375
415
446
494
533
563
602

Mass of Motor Mass of Motor (kg)

Mounting
With
9015 9025 9030 9035 9040 9045 9050 9055 Flange (kg) Without
Brake Btake

MD
144
185
188
232
297
297
297
297
297
412

376.5
376.5
406.5
406.5

405.5
405.5
435.5
435.5
435.5
435.5

457.5
457.5
487.5
487.5
487.5
487.5
487.5

457.5
457.5
487.5
487.5
487.5
487.5
487.5
517.5

497.5
497.5
527.5
527.5
527.5
527.5
527.5
557.5
557.5

497.5
497.5
527.5
527.5
527.5
527.5
527.5
557.5
557.5

560.5
590.5
590.5
590.5
590.5
590.5
620.5
620.5
620.5

Hollow Shaft (Shrink Disk Type)

TU1

Nomenclature

*) Mass of drive unit with motor, add mass of motor ange

and mass of motor, shown in table below.

Solid Shaft

Size

Key
Y1 Z1
7
11
7.5 12
9
14
9
14
9
14
10 16
10 16
11 18

X1
18
20
22
25
25
28
28
32
Low Speed
Shaft
Type

L1
95
125
150
150
150
190
190
185

43
57
76
131
213
213
224
259
259
276

54
77
96
175
258
258
280
320
320

Hollow Shaft (Key Type)

TU2 T2

U2

328
358
393
403
448
463
503
528

135 63 60 270
145 73 70 300
160 83 80 330
160 88 85 330
180 98 95 360
180 108 105 370
200 108 105 410
205 123 120 410

193
213
233
243
268
283
303
323

V2

8
8
11
11
17
17
17
15
15
29

560.5
590.5
590.5
590.5
590.5
590.5
620.5
620.5
620.5

Oty Wt. (kg)

DP1 DP2 Oil(L)
3/4" 3/4" 6
125
3/4" 3/4" 8
175
3/4" 3/4" 10
235
3/4" 3/4" 14
260
1"
1"
18
340
1"
1"
22
410
1"
1"
25
490
1"
1"
35
555

Size

RI

E3

E2

E1

Triple
Reduction

160
175
200
219
235
256
255
286

5.5
7.5
11
15
18.5
22
30
37
45
55

Parallel

338
408
453
484
540
577
609
648

kW

9015
9055

9015
9025
9030
9035
9040
9045
9050
9055

9015
9025
9030
9035
9040
9045
9050
9055

C1

Monoblock

Vertical

PARAMAX

Size

9015 9055

V3 TU4 T4
135
150
165
165
180
185
205
205

U4

V4

V5

135 55 55
150 65 65
165 75 75
165 85 85
180 90 90
185 105 105
205 105 105
205 115 115
Unit: mm

Nominal
Reduction Ratio

RML
RMR

Size

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

9015

9025

9030

9035
9040

9045
9050
9055

50

56

63

71

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 107

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

9060 9085

MB

MA

P1

MD

N1

MC
NP

C1
B

M1

Drive Unit

M2

DP1

E2

RI

M1

E1

Dimension Selection
Tables
Tables

K
G

DP2

E3

4- J
G

* Refer to footnote 3.

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

TU1

TU2

U4

V2

X1

T4

Z1

Y1

TU4
T2

V4

U2

V3

T1

V1

U1
L1

Hollow Shaft (Key Type)

Refer to the page D -18 for details.

W1

Refer to the page D -18 for details.

Standard Shaft Arrangement Conguration

RML

RMR

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996) Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RMR is equipped with oil gauge. Refer to the page D-28.

B - 108

V5

Solid Shaft

4.
5.
6.
7.

Refer to the page D-15 for dimensions not shown in these drawings.
Refer to the page D -28 for the dimension of optional parts.
Refer to the page D-33 for motor terminal box position.
Refer to the page D-34 for ange dimension.

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

H

RI

M2

N1

NP

P1

540
251 530 282
586
290 600 317
630 See 283 600 317
683 below 330 670 352
725
325 670 352
781
369 750 392

265
300
300
335
335
375

35
35
40
40
40
40

35
35
40
52
52
52

160
175
175
190
190
215

35
35
42
42
42
42

180
180
215
220
220
220

970
1055
1115
1215
1275
1375

140
175
155
195
170
210

118
153
128
163
140
180

277.5
277.5
302.5
302.5
322.5
322.5

35
38
38
40
45
40

117
117
117
117
117
117

460
530
520
590
590
670

190
190
215
215
230
230

223
223
253
253
283
283

649
695
752
805
870
926

*) Mass of drive unit with motor, add mass of motor ange and
mass of motor, shown in table below.

Motor
Without Brake
MA MB MC
575 251 350
700 324 350
835 394 400
835 394 400
835 394 400
930.5 394 450
930.5 394 450

MD
188
232
297
297
297
297
297
412
485
485
515

Mass of Motor Mass of Motor (kg)

Mounting
With
9060 9065 9070 9075 9080 9085 Flange (kg) Without
Brake Btake
633
633
633
633
633
663
663
663
663

633
633
633
633
633
663
663
663
663

Solid Shaft

Size
9060
9065
9070
9075
9080
9085

683
683
683
713
713
713
713
713

683
683
683
713
713
713
713
713
743

749
779
779
779
779
779
809

11
11
17
17
17
15
15
29
31
31
56

749
779
779
779
779
779
809

Hollow Shaft (Shrink Disk Type)

TU1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

Key
Y1 Z1
11 18
12 20
12 20
13 22
13 22
15 25

L1
185
225
225
275
275
270

76
131
213
213
224
259
259
276
490
540
675

96
175
258
258
280
320
320

Hollow Shaft (Key Type)

TU2 T2

U2

V2

V3 TU4 T4

U4

V4

V5

583
594
644
651
714
714

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

353
359
384
386
429
429

Oty Wt. (kg)*)

DP1 DP2 Oil(L)
1"
1"
32
730
1"
1"
35
885
1"
1"
53
1030
1"
1"
67
1255
1"
1"
65
1460
1"
1"
89
1730

Size

E3

E1

Triple
Reduction

299
338
336
383
378
422

11
15
18.5
22
30
37
45
55
75
90
110

E2

With Brake
MA MG
MC
480 251
350
545 324
350
625 394
400
625 394
400
625 394
400
715.5 394
450
715.5 394
450
769.5 484
550
799 490
545
799 490
545
898 550
655

Parallel

701
747
809
862
932
988

kW

9060
9085

9060
9065
9070
9075
9080
9085

9060
9065
9070
9075
9080
9085

C1

Split

Vertical

PARAMAX

Size

9060 9085

470
480
530
530
570
570

235
240
265
265
285
285

Unit: mm

Nomenclature
Shaft
Arrangement

Size

P V D

Low Speed
Shaft
Type

P 3 9060
9065
9070
9075
9080
9085

Nominal
Reduction Ratio

(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

RML
RMR

Size
9060

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075
9080
9085

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

B - 109

Exact Reduction Ratio Drive Unit Right Angle Shaft

Nominal
Reduction Ratio

Drive Unit

Dimension Selection
Tables
Tables

B - 110

Size of Reducer
9030

9035

9040

6.3

6.378

6.111

7.1

6.875

6.973

9045

8.118

7.950

7.778

7.770

8.750

8.643

8.875

8.839

9050

10

10.303

10.118

9.608

9.889

11.2

11.106

11.000

10.963

11.250

12.5

12.756

12.842

12.222

12.216

14

13.750

13.962

13.946

13.897

16

15.897

15.899

15.556

15.540

18

17.135

17.286

17.750

17.679

20

20.091

19.814

19.620

19.778

19.790

22.4

21.656

21.542

22.388

22.500

22.530

25

25.137

25.041

24.444

24.945

25.935

9055

9060

9065

19.181

25.137

9075

9080

9085

19.950

22.351
24.662

9070

22.353
24.053

24.938

24.700

28

27.096

27.225

27.893

28.379

29.526

27.706

29.291

27.509

27.941

27.718

31.5

32.455

31.331

31.694

31.079

31.969

32.319

30.157

31.521

31.129

30.875

35.5

34.983

34.063

36.165

35.357

36.395

36.309

35.140

36.050

34.879

34.647

40

40.607

40.451

39.487

40.296

41.895

39.838

39.520

37.815

38.912

38.541

45

43.770

43.979

45.058

45.843

47.695

44.756

46.051

43.250

43.599

43.250

50

51.141

50.611

49.942

50.205

51.869

52.207

50.273

49.557

49.500

48.176

56

55.125

55.025

56.987

57.115

59.051

58.652

58.582

56.678

55.462

54.062

63

63.986

53.741

62.222

63.497

64.640

64.637

63.984

63.041

63.000

61.286

71

68.971

69.300

71.000

72.237

73.590

72.617

74.559

72.101

70.588

68.773

80

79.751

77.989

79.111

79.341

80.552

78.377

80.234

78.120

78.000

79.124

90

86.706

88.991

90.000

90.326

90.496

91.330

91.765

87.529

87.529

87.269

100

99.259

99.158

103.97

98.871

102.71

98.282

97.650

96.720

96.444

96.432

112

113.26

112.81

118.37

111.08

119.69

112.41

109.41

108.54

106.37

105.89

125

122.72

126.20

130.09

129.57

127.97

128.80

127.97

120.90

126.39

117.54

140

140.03

143.57

148.10

145.56

149.12

147.31

143.38

135.67

139.40

129.07

160

156.02

158.68

162.11

156.75

160.47

152.99

158.44

158.25

154.04

180

177.50

180.65

182.13

182.66

183.53

171.41

177.79

174.54

169.14

200

207.95

197.74

205.42

196.56

191.23

189.41

192.89

192.86

224

236.74

222.15

239.37

224.81

214.26

212.55

212.75

211.77

250

260.18

259.14

255.94

257.59

250.61

236.76

252.78

235.08

280

296.20

291.13

298.24

294.61

280.79

265.69

278.80

258.13

315

315.95

324.22

332.51

320.94

322.08

310.27

318.63

308.07

355

367.08

364.25

369.46

367.06

343.56

348.18

355.25

338.28

400

388.53

409.25

399.38

386.60

450

451.41

454.72

426.01

431.03

Exact Reduction Ratio Drive Unit Parallel Shaft

Size of Reducer

Nominal
Reduction Ratio

9015

9025

9030

6.3

6.257

6.193

6.314

6.049

6.470

6.188

6.246

6.429

7.1

7.237

7.067

6.806

6.903

7.366

7.210

6.998

7.090

9035

9040

9045

9050

9055

9060

9065

9070

9075

9080

9085

7.889

7.616

8.118

7.869

7.778

7.691

7.956

8.062

7.875

7.759

8.033

7.733

8.167

7.835

9.125

8.690

8.750

8.556

8.875

8.750

9.057

9.058

9.176

8.874

9.000

8.677

9.007

8.603

10

10.143

9.722

9.944

10.118

9.528

9.889

10.156

9.914

9.750

9.875

9.665

9.945

9.905

9.953

11.2

11.732 11.094 10.719 11.000 10.872 11.250 11.562 11.138 11.361 11.294 10.829 11.160 10.924 10.929

12.5

12.710 12.407 12.785 12.394 12.485 12.114 12.594 12.656 12.206 12.226 12.600 11.966 12.762 12.071

14

14.701 14.158 13.781 13.475 14.247 13.781 14.337 14.219 14.224 13.983 14.118 13.428 14.076 13.255

16

15.778 15.340 15.997 15.935 15.556 15.874 16.504 15.694 15.996 15.306 15.750 15.600 15.556 15.554

18

18.250 17.503 17.243 17.325 17.750 18.059 18.789 17.631 18.640 17.506 17.647 17.506 17.157 17.078

20

19.894 19.681 20.280 19.938 19.884 19.778 19.590 20.566 18.988 20.059 20.067 19.500 20.054 18.958

22.4

23.011 22.457 21.860 21.676 22.689 22.500 22.303 23.105 22.125 22.941 22.484 21.882 22.119 20.817

25

24.696 24.332 25.374 25.277 24.774 25.281 25.673 24.413 24.883 23.810 25.083 28.844 24.444 24.441

28

28.565 27.764 27.350 27.481 28.269 28.761 29.227 27.426 28.995 27.231 28.105 27.880 26.961 26.838

31.5

31.401 31.905 32.876 31.625 31.213 31.498 30.855 31.992 29.905 31.202 31.500 31.056 31.601 29.792

35.5

36.321 36.406 35.438 34.383 35.617 35.833 35.127 35.942 34.848 35.686 35.294 34.850 34.854 32.712

40

38.980 39.444 41.134 40.976 38.889 39.686 40.435 38.450 39.190 37.500 39.375 39.000 38.519 38.514

45

45.088 45.009 44.338 44.550 44.375 45.148 46.033 43.197 45.667 42.889 44.118 43.765 42.484 42.289

50

51.141 51.268 49.248 49.444 49.634 50.388 48.825 49.144 51.188 48.750 51.845 46.944

56

55.125 55.739 56.195 56.250 56.507 56.608 56.894 56.206 57.353 54.706 57.182 51.547

63

63.986 63.741 61.358 62.615 65.045 61.852 63.984 61.225 63.984 63.375 63.194 63.186

71

68.971 69.300 70.014 71.234 74.051 69.488 74.559 70.024 71.691 71.118 69.700 69.381

80

79.751

78.012

81.056

80.234

79.219

77.018

90

86.706

88.750

91.063

91.765

88.897

84.569

B - 111

memo

B - 112

C
<Reducer: Right Angle Shaft Horizontal Mounting>

<Reducer: Parallel Shaft-Horizontal Mounting>

Reducer
Standard Specications

C- 2
C- 3
C- 4

Construction Drawing

Nomenclature

Selection Flowchart and Formula

for Selection
C- 6
Service Factor
C- 8
Right Angle Shaft
C- 11
Parallel Shaft
C-101

C-1

Reducer Standard Specifications

Ambient Conditions

Reducer

Item

Lubrication
Method

Standard Specification
Mounting

High Speed Shaft Speed

Horizontal Shaft

750 1800r/min

Oil bath lubrication

In case of high speed shaft speed is less than 750r/min, electric pump
lubrication may be used. Consult SUMITOMO for details.

Vertical Shaft

400 1800r/min

Pump lubrication
(Two different pump lubrication systems are available;
shaft connected pump lubrication and electric pump lubrication.
For details, refer to the outline dimension drawing.)

Upright Shaft

750 1800r/min

Oil bath lubrication

Grease lubrication for right angle input shaft.

Lubricant

Refer to the page D-2.

Gear Type

Involute external gear

Installation
Location

Indoor (Minimal dust and humidity)

Ambient
10 40
Temperature A cooling fan may be required depending on the usage (Note)
Ambient
Humidity

Under 85%

Elevation

Under 1,000 meters

Atmosphere Well ventilated location, free of corrosive gases, explosive gases, vapors and dust.
Installation
Method of
Coupling with
Driven Machine

Dimension Selection
Tables
Tables

Speed
Reducer

Painting

Horizontal installation
Refer to the page D-2
Coupling, gears, chain sprocket or belt.
Surface preparation: Shot blasting after washing before machining
Inside painting: UNI GROUND PTC primer is sprayed once
Outside painting: For primer coating, UNI GROUND PTC primer is sprayed once.

For final coating, NEORON #2000 is sprayed once.
Painting color: Donau Blue (equivalent Munsell color: 6.5PB 3.6/8.2), Refer to the page D-3.

Note : In general, a heating or cooling system is necessary when ambient temperature is lower than -10 or higher than
50.

e.g. High temperature gas or liquid passes through the hollow shaft.

Consult us when substances lower than 10 or higher than 50 will be in contact with PARAMAX DRIVES.

C-

Reducer Construction Drawing

18

17

16

15

14

13

12

10

11

<Reducer: Right Angle Triple Reduction>

19

20

21

<Reducer: Parallel Shaft Triple Reduction>

Ref.No.

Part Name

Ref.No.

Part Name

Ref.No.

Part Name

Ref.No.

Part Name

Housing

Taper roller bearing

13

Bearing housing

19

Helical gear

Helical gear

Bevel gear

14

Oil pump

20

Collar

Slow speed shaft

Spherical roller bearing

15

Helical gear

21

Helical pinion shaft

Taper roller bearing

10

Bevel pinion shaft

16

Taper roller bearing

Helical pinion shaft

11

Oil seal

17

Collar

Helical pinion shaft

12

Taper roller bearing

18

Oil seal

C-3

Reducer Nomenclature

Series

Mounting

Housing

9025

4.2

9030

6.4

9035

8.5

Monoblock

9040

10.1

9045

13.2

9050

15.3

9055

19.9

9060

24.4

9065

31.4

9070

38.2

9075

47.8

9080

58.5

9085

73.1

9090

85.9

9095

101

Split

9100

122

9105

144

9110

174

9115

207

9118

260

9121

301

9126

351

9128

420

9131

473

9136

552

Speed
Reducer

Dimension Selection
Tables
Tables

P
Vertical

Upright

1. For shaft arrangement, refer to the dimension sheets.

2. Consult us for reduction ratios smaller than 6.3.

C-4

Torque
kNm

2.6

Size

9015

Horizontal

Paramax

9075

Shaft Position

Number of Gear
Stages

Double Reduction

Right Angle

P
Triple Reduction

Parallel

Quadruple Reduction

Reducer Nomenclature

RL
Mounting for
Upright

Shaft Arrangement

Slow Speed
Shaft

$NCPM

$NCPM

35.5

Option

$NCPM

RL

RR
RB

Solid Shaft
Without option
LR

LL

T
LB

With fan

RL

RR

Hollow Shaft
(Shrink Disk Type)

RB

LR

K
With backstop

LL

FB
LB

Wall Mount
(Upright Mounting)

BL

BR

Hollow Shaft
(Key Type)

BB

With fan & backstop

Nominal Ratio
Right Angle Shaft
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4
25
28
31.5
35.5
40
45
50

56
63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450

Parallel Shaft
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4
25
28
31.5
35.5
40
45
50

56
63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

C-5

Reducer Selection

Standard Specifications Page C-2

PM : Actual transmission power or motor
SF : Service factor Page C-8 ~ C-9
PE : Equivalent transmission power
PE PM SF
P : Mechanical power rating
Right angle shaft: Page C12 ~ C-41
Parallel shaft: Page C-106 ~ C-135

Determine the service factor

Calculate Equivalent Transmission
Power
Determine Size
PE P

Determine Nomenclature

Determine Size

Ambient condition

Refer to the bottom row of Mechanical Power Rating

Table for page number of dimensional drawing.
Select shaft arrangement from "Standard Shaft
Arrangement Configuration" in the Dimension Tables.
Determine nomenclature.

Determine page number

indicating Dimension Table.
Determine Nomenclature

Ta : Temperature correction factor

PT : Thermal power rating
Right angle shaft: Page C-12 ~ C-41
Parallel shaft: Page C-106 ~ C-135

Check Thermal Power

Determine Temperature
Correction Factor

Check Thermal Power

PT Ta PM

Consult us for forced cooling system

such as oil cooler.

No

Yes
Calculate equivalent radial load FrE and equivalent
thrust load FxE at peak load.
Is overhung load
applied to the high
speed shaft?

Cf : Overhung factor
FrE : Equivalent radial load = Peak radial load Fr Cf
FxE : Equivalent axial load = Peak thrust load Fx Cf
FrA : Allowable radial load
FxA : Allowable axial load

No
No

Check Overhung Load

Dimension Selection
Tables
Tables

Speed
Reducer

Yes

Is overhung load
applied to the slow speed
shaft?

Refer to the following pages for Cf, FrA, and Fx A

values.
Right angle shaft: Page C-42 ~ C-45
Parallel shaft: Page C-132 ~ C-135

Yes

Is overhung load radial

load only?

Calculate equivalent radial load FrE

and calculate equivalent thrust load FxE

No

Yes
Calculate equivalent radial
load Fr E

Yes
Check overhung load
FrE

No

Check overhung load

FxE
FxA

FrE
FrA

FrA
No

Yes
Complete selection

C-6

Consult us for large overhung load.

Reducer Selection Example

Conditions Selected item
Ambient condition
Check ambient condition

: Indoor, Ambient temperature 40

OK

Motor power
High speed shaft speed
Shaft and mounting positions

: 55 kW
: 1500 r/min
: Right Angle ShaftHorizontal Mounting

Load Condition
Type of load, Operating hours
Determine service factor

: Uniform load14 hours/day

SF = 1.25

Calculate equivalent transmission power

PE = 551.25 = 68.75 kW

Slow speed shaft speed

Reduction ratio
Select nominal reduction ratio

: 85 r/min
1500/85 =17.6
17.6 18

Determine size

Size 9035, Nominal Reduction Ratio 18

C-18
Mechanical power rating P = 72 kW
PE P OK
RL

Check nomenclature

PHA9035R2-RLF-18

Ambient temperature
Temperature correction factor without fan Ta
Thermal rating without fan PT

: 40
Ta = 0.70
PT = 48kW
PT Ta = 33.6 < 55 = PM OUT

Temperature correction factor with fan Ta

Thermal rating with fan PT

Ta = 0.73
PT = 120kW
PT Ta = 87.6 > 55 = PM OK
With fan

10.6 29.4
Complete selection
Selected model

Standard Specifications

C-8

Service Factor

C-4 C-5

Nomenclature
Selection Tables

C-50 *1

Check dimension
Check shaft arrangement

Check overhung load

Overhung load to high speed shaft
Overhung member
Overhang factor Cf
Radial load position and direction
Peark radial load Fr
Peark thrust load Fx
Equivalent radial load FrE
Allowable radial load

C-2

: No load
: Sprocket (Single row)
Cf = 1.0

: Center of solid shaft, Downward

: 10.6 kN
: 0 kN
FrE = 10.61.0 = 10.6
29.4 kN

Dimension Tables
Standard shaft arrangement
configuration in Dimension
Tables
Nomenclature in Dimension
Tables

C-18
C-18

Selection Tables
Selection Tables
Standard Specifications

C-18

Selection Tables

C-42

Allowable External Load

C-42

Allowable External Load

OK

PHA9035R2-RLF-18

*1 Page number of the

relevant Dimension

Table is indicated in the

Selection Table.

C-7

Reducer Service Factor SF

Service Factor SF
Operating Hours (hours/day)

Driven Machine

3 hrs

10 hrs

CRANES
Classication of
Crane
Group
Group
Group

Travel Slewing
Hoisting Traverse
Motion Motion Motion
1.00
1.50
1.25
1.25
1.50
1.50
1.75
1.75

2.00

Boom
Hoisting
1.00
1.00
1.25
1.50

The crane
classication is
based on JIS
B8821-1976
"Calculation standard
for the structure of
crane."

CONVEYORS (General purpose)

Uniformly load or fed
Heavy load
Not uniformly fed
Reciprocating or shaker

1.00
1.00
1.50

1.00
1.25
1.75

1.25
1.50
2.00

Elevators
Escalators

10 hrs

24 hrs

1.75
1.50
1.50

1.75
1.50
1.50

2.00
1.75
1.50

1.75
2.00

1.75
2.00

1.75
2.00

1.25
1.50
1.50

1.25
1.50
1.50

1.25
1.50
1.50

2.00

2.00

2.00

Draw bench carriage and main drive

Runout table
Non reversing
Group drives
Individual drivers
Reversing
Slab pushers
Shears
Wire drawing
Wire winding machine

1.00
1.00
1.00

1.00
1.25
1.25

1.25
1.50
1.50

1.25

1.25

1.50

2.50

2.50

2.50

1.00
1.00
1.00

1.00
1.25
1.25

1.25
1.50
1.50

1.00
1.00
1.50
1.75

1.00
1.25
1.50
1.75

1.25
1.50
1.75
2.00

1.00

1.25
1.50
1.50

1.00

1.25
1.50
1.50

1.25

1.25
1.50
1.50

1.00
1.25
1.25

1.00
1.25
1.25

1.25
1.50
1.50

1.25
1.25
2.00
2.00
1.75
1.25
1.25

1.25
1.25
2.00
2.00
1.75
1.25
1.25

1.50
1.50
2.00
2.00
2.00
1.50
1.50

GENERATORS AND EXCITERS

1.00

1.00

1.25

HAMMER MILLS

1.75

1.75

2.00

2.00
1.50
1.50
1.75

2.00
1.50
1.50
1.75

2.00
1.50
1.50
1.75

1.50
1.25

AGITATORS AND MIXERS

1.50

1.50

1.50

Pure liquids
Liquids and solids
Liquids variable density

1.50
2.00
2.00
1.50
2.00
1.25
1.25

1.50
2.00
2.00
1.50
2.00
1.25
1.50

1.50
2.00
2.00
1.50
2.00
1.25
1.50

1.50
1.00
1.00
1.25
1.50
1.25
2.00
2.00
1.00

1.50
1.25
1.25
1.25
1.50
1.25
2.00
2.00
1.25

1.50
1.50
1.50
1.50
2.00
1.50
2.00
2.00
1.50

2.00
2.00
1.50
1.50

2.00
2.00
1.50
1.50

2.00
2.00
1.50
1.50

2.00
1.25
1.25
1.50
1.50
1.50
1.25
1.50
1.50

2.00
1.25
1.25
1.50
1.50
1.50
1.25
1.50
1.50

2.00
1.25
1.25
1.50
1.50
1.50
1.25
1.50
1.50

MIXERS

SEWAGE DISPOSAL EQUIPMENT

Aerators
Bar screens
Chemical feeders
Dewatering screens
Scum breakers
Slow or rapid mixers
Sludge collectors
Thickeners
Vacuum filters

1.25
1.50

1.25
1.50

1.25
1.50

1.00
1.00
1.00
1.50
1.00

1.25
1.25
1.00
1.75
1.25

1.50
1.50
1.25
2.00
1.50

FEEDERS
Apron
Belt
Disk
Reciprocating
Screw

CRUSHER
Stone or ore

BLOWERS
Centrifugal
Lobe
Vane
Centrifugal
Lobe
Reciprocating: multi cylinder
Reciprocating: single cylinder

FANS
Centrifugal
Cooling towers
Forced draft
Suction draft
Industrial and mine

PUMPS
Centrifugal
Screw pump
Gear pump

DREDGES

EXTRUDERS
Plastics
Rubber

Concrete

COMPRESSORS

MILL, ROTARY TYPE

Ball and rod
Cement Kilns
Kilns (Except cement kilns)
Dryers and coolers

All types incl. Paper making machine

1.50
1.25

METAL STRIP PROCESSING MACHINERY

Bridles
Coilers & uncoilers
Edge trimmers
Flatteners
Loopers (Accumulators)
Pinch rolls
Scrap choppers
Shears
Slitters

Mixers
Mixing mill -2 smooth rolls
Batch drop mill -2 smooth rolls
Cracker warmer
-2 roll: 1 corrugated roll
Cracker -2 corrugated rolls
Holding, feed and blend mill
-2 rolls
Rener -2 rolls
Calenders

1.50
1.25

METAL MILLS

Dimension Selection
Tables
Tables

3 hrs

PAPER MILL

ELEVATORS

C-8

Operating Hours (hours/day)

RUBBER INDUSTRY

Group

Speed
Reducer

Driven Machine

24 hrs

Cable reels
Conveyors
Cutter head drive
Pumps
Screen drives
Stackers
Winches

SUGAR INDUSTRY
Beet slicer
Cane knives
Crushers
Mills (Slow speed end)

Notes:
(1) Values in the above table are based on AGMA standards and SUMITOMO's
experience.
(2) Values in the above table apply for electric motors as prime movers - if prime
mover is a multi cylinder combustion engine, 0.25 has to be added to the SF.
(3) Consult us for special duty or when special safety specifications are needed.
(4) : For SF, consult us.

Reducer Service Factor SF

Refer to the following for driven machines not shown on the left page.
Type of Load
Prime Mover

Operating
Hours

Uniform Load

Moderate
Shock Load

Heavy Shock
Load

Electric Motor

3 hours/day
10 hours/day
24 hours/day

1.00
1.00
1.25

1.00
1.25
1.50

1.50
1.75
2.00

Internal Combustion
Engine
(multi cylinder)

3 hours/day
10 hours/day
24 hours/day

1.00
1.25
1.50

1.25
1.50
1.75

1.75
2.00
2.25

Note: Consult us when the operating hours are less than 3 hours/day or when an internal combustion
engine (single cylinder) is used.

C-9

C - 10

<Reducer: Right Angle Shaft-Horizontal Mounting>

<Reducer: Right Angle Shaft Upright Mounting>

<Reducer: Right Angle Shaft Vertical Mounting>

Reducer: Right Angle

Selection Tables
Allowable Loads
Dimension Sheets

C- 12
C- 42
C- 46

C - 11

SELECTION Right Angle Shaft Double Reduction

Nominal Reduction Ratio 6.3 8

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
286
1500
238
6.3
1200
190
1000
159
900
143
750
119
Exact Reduction Ratio
1800
254
1500
211
1200
169
7.1
1000
141
900
127
750
106
Exact Reduction Ratio
1800
225
1500
188
8
1200
150
1000
125
900
113
750
94
Horizontal
Dimension
Vertical
Tables
Upright

6.265

6.049

6.539

6.405

6.384

6.188

6.188

74
62
49
41
37
31

98
81
65
54
49
41

152
127
102
85
76
64

236
197
158
132
119
99

334
279
224
187
168
141

568
475
381
318
287
240

798
667
535
447
403
337

7.246

6.903

7.049

7.309

7.268

7.210

6.933

62
52
42
35
31
26.5

98
81
65
54
49
41

152
127
102
85
76
64

228
191
153
128
116
97

334
279
224
187
168
141

559
469
377
316
285
238

798
667
535
447
403
337

7.889

8.056

8.118

8.125

7.875

8.150

7.778

8.144

76 140 152 217 236 340

57
63 117 127 181 197 285
47
94 102 145 158 229
51
38
85 120 132 191
78
42
31
76 108 119 173
71
38
28.6
99 144
90
64
59
31
23.8
C-46 C-46 C-46 C-46 C-46 C-46 C-46
C-72 C-72 C-72 C-72 C-72 C-72 C-72
C-88 C-88 C-88 C-88 C-88 C-88 C-88

7.759

8.082

544 568 810

467 475 705
374 381 568
312 318 476
280 287 429
234 240 359
C-48 C-48 C-48
C-74 C-74 C-74
C-90 C-90 C-90

6.286

1020
857
688
575
518
433
6.933

1020
857
688
575
518
433
8.190

1150
1010
834
699
630
528
C-48
C-74
C-90

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
30
39
46
61
73
88
79
108
134
138
160
1800
1
75
105
124
171
217
261
233
332
414
372
561
Double
31
40
49
64
77
92
86
118
146
154
183
Reduction 1500
1
68
95
117
160
203
243
224
326
402
369
574
Horizontal
31
40
50
66
79
95
90
126
154
165
200
1200
Type
1
60
84
106
145
184
223
208
307
376
351
557
30
39
50
65
78
95
91
128
156
169
207
1000
1
52
73
94
128
163
198
186
276
337
319
511
6.3
29
39
50
65
78
94
91
128
156
169
209

900
1
48
69
89
121
154
187
178
265
323
306
493
8
28
37
48
63
76
92
89
127
154
169
209
750
1
42
60
79
107
137
167
159
239
290
278
449

1800
Double
Reduction
Vertical
Type

6.3

1500
1200
1000
900
750
1800

Double
Reduction
Upright
Type

6.3

1500
1200
1000
900
750

C - 12

1
1
1
1
1
1

30
75
31
68
31
60
30
52
29
48
28
42

39
105
40
95
40
84
39
73
39
69
37
60

46
124
49
117
50
106
50
94
50
89
48
79

61
171
64
160
66
145
65
128
65
121
63
107

73
217
77
203
79
184
78
163
78
154
76
137

88
261
92
243
95
223
95
198
94
187
92
167

79
233
86
224
90
208
91
186
91
178
89
159

108
332
118
326
126
307
128
276
128
265
127
239

134
414
146
402
154
376
156
337
156
323
154
290

138
372
154
369
165
351
169
319
169
306
169
278

160
561
183
574
200
557
207
511
209
493
409
449

1
1
1
1
1
1

24
60
25
54
24
48
24
41
23
39
23
34

31
84
32
76
32
67
31
58
31
55
30
48

37
99
39
93
40
85
40
75
40
71
39
63

49
137
51
128
52
116
52
102
52
97
50
86

58
174
61
162
63
147
63
130
62
124
61
110

70
209
74
195
76
178
76
158
75
150
74
133

64
186
69
179
72
166
73
149
72
142
71
128

86
266
95
260
100
245
102
221
102
212
101
191

107
331
117
321
123
301
125
270
125
258
123
232

110
297
123
295
132
281
135
255
136
245
135
222

128
449
146
459
160
446
166
408
167
395
167
360

SELECTION Right Angle Shaft Double Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 6.3 8

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

286
1800
238
1500
6.3
190
1200
159
1000
143
900
119
750
Exact Reduction Ratio
254
1800
211
1500
7.1
169
1200
141
1000
127
900
106
750
Exact Reduction Ratio
225
1800
188
1500
8
150
1200
125
1000
113
900
94
750
Horizontal
Dimension
Vertical
Tables
Upright

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

1800
1.00
20
1.00
1
Double
0.85
30
0.87
1500 Reduction
1
Horizontal
0.70
40
0.73
1200
Type
1
0.55
50
0.60
1000
1
6.3

900
1
8
0QVGU
750
1
Size of Reducer

1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

Double

1500 Reduction
1200
1000
900

Vertical
Type

6.3

750

Double

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

6.3

750

C - 13

SELECTION Right Angle Shaft Double Reduction

Nominal Reduction Ratio 9 11.2

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
200
1500
167
9
1200
133
1000
111
900
100
750
83
Exact Reduction Ratio
1800
180
1500
150
10
1200
120
1000
100
900
90
750
75
Exact Reduction Ratio
1800
161
1500
134
11.2
1200
107
1000
89
900
80
750
67
Horizontal
Dimension
Vertical
Tables
Upright

9.125

9.192

8.750

8.861

8.875

9.265

9.250

8.938

9.176

8.874

9.056

49
41
33
28.0
25.3
21.1

76
63
51
42
38
31

126
105
85
71
64
53

152
127
102
85
76
64

188
158
127
106
95
80

236
197
158
132
119
99

280
234
188
158
142
119

334
279
224
187
168
141

443
371
298
250
225
188

568
475
381
318
287
240

704
590
474
397
358
300

10.040 9.899 10.303 10.118 10.171 9.889 10.000 10.125 9.995

43
36
29.1
24.3
21.9
18.2

72
60
48
40
36
30

111
92
74
62
55
46

143
119
95
79
71
59

161
134
107
89
80
67

217
181
145
120
108
90

278
232
187
156
141
118

351
297
237
198
178
148

434
362
289
241
217
181

8.597

9.034

798 1070
667 897
535 722
447 605
403 546
337 457

9.875 10.125 10.007 9.882

546
469
375
313
281
234

677
567
456
382
344
288

9.982

810 1000 1150

713 863 1010
577 695 867
482 582 736
435 525 663
363 439 553

11.614 11.295 11.106 11.000 11.606 11.250 11.385 11.375 11.647 11.294 11.345 11.229 10.900 10.961

63 100 133 145 198 229 293 351 462 565 747 892 1120
39
83 111 121 166 191 245 294 387 473 626 748 938
52
33
97 133 154 197 236 311 381 504 602 756
89
67
42
26.5
81 111 129 165 198 260 319 421 504 633
75
56
35
22.1
73 100 116 149 178 235 287 380 454 571
67
50
31
19.9
97 124 149 196 240 318 380 478
84
61
56
42
16.7 26.6
C-46 C-46 C-46 C-46 C-46 C-46 C-46 C-46 C-48 C-48 C-48 C-48 C-48 C-48
C-72 C-72 C-72 C-72 C-72 C-72 C-72 C-72 C-74 C-74 C-74 C-74 C-74 C-74
C-88 C-88 C-88 C-88 C-88 C-88 C-88 C-88 C-90 C-90 C-90 C-90 C-90 C-90

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
27
36
44
56
69
82
78
99
109
130
142
173
164
203
1800
1
67
96
118
156
205
244
227
290
337
402
382
467
577
715
Double
27
36
46
58
71
85
82
105
116
141
153
188
183
226
Reduction 1500
1
59
86
109
144
187
225
214
274
319
388
368
452
575
708
Horizontal
26
36
46
59
71
86
84
108
120
147
160
198
195
242
1200
Type
1
52
76
98
129
166
202
195
250
292
359
341
422
543
673
26
35
46
58
70
85
84
108
120
148
161
200
199
248
1000
1
44
66
85
113
145
177
173
222
260
320
305
379
491
610
9
25
34
45
57
69
84
84
108
119
148
161
200
200
249

900
1
41
62
81
107
137
167
164
211
247
306
291
363
471
586
11.2
24
33
44
56
66
82
82
105
117
146
158
198
198
247
750
1
36
54
71
95
120
149
146
188
221
275
261
326
425
531

1800
Double
Reduction
Vertical
Type

11.2

1500
1200
1000
900
750
1800

Double
Reduction
Upright
Type

11.2

1500
1200
1000
900
750

C - 14

1
1
1
1
1
1

27
67
27
59
26
52
26
44
25
41
24
36

36
96
36
86
36
76
35
66
34
62
33
54

44
118
46
109
46
98
46
85
45
81
44
71

56
156
58
144
59
129
58
113
57
107
56
95

69
205
71
187
71
166
70
145
69
137
66
120

82
244
85
225
86
202
85
177
84
167
82
149

78
227
82
214
84
195
84
173
84
164
82
146

99
290
105
274
108
250
108
222
108
211
105
188

109
337
116
319
120
292
120
260
119
247
117
221

130
402
141
388
147
359
148
320
148
306
146
275

142
382
153
368
160
341
161
305
161
291
158
261

173
467
188
452
198
422
200
379
200
363
198
326

164
577
183
575
195
543
199
491
200
471
198
425

203
715
226
708
242
673
248
610
249
586
247
531

1
1
1
1
1
1

22
53
22
47
21
41
20
35
20
33
19
29

29
76
29
69
29
61
28
52
28
49
26
43

35
95
37
87
37
78
36
68
36
64
35
57

45
125
46
115
47
104
46
91
46
86
45
76

55
164
57
150
57
133
56
116
55
109
53
96

66
195
68
180
69
161
68
141
67
134
66
119

62
182
66
171
68
156
67
138
67
131
65
117

79
232
84
219
86
200
87
178
86
169
84
151

87
270
93
255
96
234
96
208
96
198
94
176

104
321
113
310
118
287
118
256
118
245
117
220

113
306
123
295
128
273
129
244
129
233
127
209

138
373
151
362
158
338
160
303
160
290
158
261

131
461
147
460
156
434
159
392
160
377
158
340

163
572
181
567
194
538
198
488
199
469
198
425

SELECTION Right Angle Shaft Double Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
9.000

9.000

8.947

1550
1350
1120
964
882
756

1880
1660
1420
1250
1160
998

2800
2460
2110
1850
1720
1500

9.765

9.765

10.235

1460
1280
1060
911
834
716

1880
1660
1420
1250
1160
998

2800
2460
2060
1770
1620
1390

11.382

11.382

11.302

1230
1050
877
752
688
590
C-50

1570
1380
1180
1040
971
833
C-50

2430
2140
1780
1520
1390
1200
C-50

Nominal Reduction Ratio 9 11.2

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

200
1800
167
1500
9
133
1200
111
1000
100
900
83
750
Exact Reduction Ratio
180
1800
150
1500
10
120
1200
100
1000
90
900
75
750
Exact Reduction Ratio
161
1800
134
1500
11.2
107
1200
89
1000
80
900
67
750
Horizontal
Dimension
Vertical
Tables
Upright

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

1800
1.00
20
1.00
490
1
Double
200
0.85
30
0.87
1500 Reduction
538
560
570
1
Horizontal
0.70
220
270
40
0.73
1200
Type
525
599
590
1
0.55
50
0.60
210
280
320
1000
444
551
600
1
9
210
270
330

900
425
508
593
1
11.2
0QVGU
190
250
320
750
350
429
523
1
Size of Reducer

1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

Double

1500 Reduction
1200
1000
900

Vertical
Type

11.2

750

Double

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

11.2

750

C - 15

SELECTION Right Angle Shaft Double Reduction

Nominal Reduction Ratio 12.5 16

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
144
1500
120
12.5
1200
96
1000
80
900
72
750
60
Exact Reduction Ratio
1800
129
1500
107
14
1200
86
1000
71
900
64
750
54
Exact Reduction Ratio
1800
113
1500
94
16
1200
75
1000
63
900
56
750
47
Horizontal
Dimension
Vertical
Tables
Upright

12.162 12.020 12.545 12.842 12.727 12.932 12.188 12.462 12.469 12.534 12.797 12.536 12.923 12.044

36
30
24.2
20.1
18.1
15.1

58
48
39
32
29.3
24.4

89
74
59
49
44
37

111
93
74
62
55
46

122
102
82
68
61
51

161
134
107
89
80
67

225
188
150
125
112
94

284
237
189
158
142
118

322
269
216
180
162
136

435
362
290
242
217
181

512
428
343
286
258
215

700
598
482
403
364
304

732 1000
612 863
491 715
410 600
369 540
308 450

14.068 13.716 13.523 13.962 14.523 14.712 13.875 14.000 14.529 14.335 14.338 14.067 14.253 13.225

32
27.3
21.9
18.3
16.5
13.8

51
43
34
28.7
25.8
21.5

82
69
55
46
41
34

105
88
71
59
53
44

116
97
78
65
58
49

152
126
101
84
76
63

188
158
127
106
95
80

239
200
161
134
121
101

283
237
190
159
143
120

366
306
246
206
186
155

450
377
303
253
228
191

600
502
404
338
305
255

688 933
576 782
463 629
388 527
350 475
292 398

15.778 15.988 16.235 15.636 15.556 16.182 15.881 15.188 15.392 15.635 15.750 15.844 16.000 15.750

96 122 169 226 261 322 373 512 545

89
67
42
27.1
80 102 141 188 218 269 311 428 455
74
56
35
22.6
82 113 150 175 216 250 343 365
64
59
45
18.1 28.5
94 125 146 180 208 286 305
68
54
49
37
15.1 23.7
84 113 131 162 188 258 275
61
48
44
33
13.5 21.4
94 109 136 157 215 229
70
51
40
37
11.3 17.8 28.2
C-46 C-46 C-46 C-46 C-46 C-46 C-46 C-46 C-48 C-48 C-48 C-48 C-48
C-72 C-72 C-72 C-72 C-72 C-72 C-72 C-72 C-74 C-74 C-74 C-74 C-74
C-88 C-88 C-88 C-88 C-88 C-88 C-88 C-88 C-90 C-90 C-90 C-90 C-90

732
612
491
410
369
308
C-48
C-74
C-90

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
23
33
41
54
63
79
73
96
101
130
137
175
172
208
1800
Double
1
57
88
110
150
187
235
214
282
312
402
369
472
607
731
Reduction
23
33
41
55
63
79
74
98
103
133
140
180
178
224
1500
1
50
77
98
137
166
209
192
256
283
366
336
433
558
702
Horizontal
22
31
40
55
61
78
73
98
103
134
140
181
180
230
Type
1200
1
42
66
85
121
144
183
169
227
250
327
298
387
500
641
21
30
39
54
59
76
71
96
101
132
138
179
178
229
1000
1
36
56
73
105
123
158
146
198
218
286
260
339
438
565
12.5
20
29
38
53
58
74
70
95
99
130
136
177
176
227
900

1
33
52
68
99
115
147
137
186
205
269
245
321
414
535
19
28
36
51
55
71
67
92
95
126
131
172
171
221
16
750
1
28
45
59
86
100
129
120
164
180
237
216
284
367
475

1800
Double
Reduction
Vertical
Type

12.5

16

1500
1200
1000
900
750
1800

Double
Reduction
Upright
Type

12.5

16

1500
1200
1000
900
750

C - 16

1
1
1
1
1
1

23
57
23
50
22
42
21
36
20
33
19
28

33
88
33
77
31
66
30
56
29
52
28
45

41
110
41
98
40
85
39
73
38
68
36
59

54
150
55
137
55
121
54
105
53
99
51
86

63
187
63
166
61
144
59
123
58
115
55
100

79
235
79
209
78
183
76
158
74
147
71
129

73
214
74
192
73
169
71
146
70
137
67
120

96
282
98
256
98
227
96
198
95
186
92
164

101
312
103
283
103
250
101
218
99
205
95
180

130
402
133
366
134
327
132
286
130
269
126
237

137
369
140
336
140
298
138
260
136
245
131
216

175
472
180
433
181
387
179
339
177
321
172
284

172
607
178
558
180
500
178
438
176
414
171
367

208
731
224
702
230
641
229
565
227
535
221
475

1
1
1
1
1
1

18
46
18
40
17
34
17
29
16
27
15
23

26
70
26
62
25
53
24
45
23
42
22
36

33
88
33
79
32
68
31
58
30
55
29
47

43
120
44
109
44
97
43
84
42
79
40
69

50
150
50
133
49
115
47
99
46
92
44
80

63
188
63
167
62
146
61
126
59
118
57
103

58
171
59
154
58
135
57
117
56
110
54
96

77
225
79
205
79
182
77
158
76
149
73
131

81
250
82
227
82
200
80
174
79
164
76
144

104
321
106
293
107
262
106
228
104
215
101
190

109
295
112
269
112
239
110
208
108
196
105
173

140
378
144
346
145
310
144
271
142
257
138
227

138
485
142
446
144
400
142
350
141
331
137
293

166
585
179
562
184
513
183
452
182
428
177
380

SELECTION Right Angle Shaft Double Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
12.349

12.349

12.929

1180
1010
840
721
660
566

1570
1380
1180
1040
971
830

2310
1980
1640
1410
1290
1110

14.143

14.344

14.260

993
852
706
605
554
475

1280
1130
966
850
790
678

1980
1700
1410
1210
1110
952

15.345

15.562

16.312

953
817
678
581
532
456
C-50

1280
1130
966
850
790
662
C-50

1840
1580
1310
1120
1020
883
C-50

Nominal Reduction Ratio 12.5 16

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

144
1800
120
1500
12.5
96
1200
80
1000
72
900
60
750
Exact Reduction Ratio
129
1800
107
1500
14
86
1200
71
1000
64
900
54
750
Exact Reduction Ratio
113
1800
94
1500
16
75
1200
63
1000
56
900
47
750
Horizontal
Dimension
Vertical
Tables
Upright

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

1800
1.00
20
1.00
490
1
Double
200
0.85
30
0.87
1500 Reduction
538
560
570
1
Horizontal
0.70
220
270
40
0.73
1200
Type
525
599
590
1
0.55
50
0.60
210
280
320
1000
444
551
600
1
12.5
210
270
330

900
425
508
593
1
16
0QVGU
190
250
320
750
350
429
523
1
Size of Reducer

1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

1500
1200

Double
Reduction
Vertical
Type

1000
900
750

12.5

16

Double

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

12.5

16

750

C - 17

SELECTION Right Angle Shaft Double Reduction

Nominal Reduction Ratio 18 22.4

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
100
1500
83
18
1200
67
1000
56
900
50
750
42
Exact Reduction Ratio
1800
90
1500
75
20
1200
60
1000
50
900
45
750
38
Exact Reduction Ratio
1800
80
1500
67
22.4
1200
54
1000
45
900
40
750
33
Horizontal
Dimension
Vertical
Tables
Upright

18.250 18.243 17.500 17.000 17.750 18.409 18.080 17.063 17.936 17.882 17.647 17.779 17.647 17.294

25.3
21.1
17.0
14.2
12.8
10.7

37
31
25.1
20.9
18.9
15.7

64
53
43
36
32
27.1

*
*
*
*
*
*

86
72
57
48
43
36

95
79
63
53
47
39

117
98
78
65
58
49

20.235

19.778

67
56
45
37
33
28.2

96
80
64
54
48
40

*
*
*
*
*
*

22.000

145
122
98
81
73
61

197
165
132
111
100
83

230
193
155
129
116
97

19.790

*
*
*
*
*
*

22.500

170
141
113
94
85
70

295
247
198
166
149
125

368
308
247
207
186
156

19.301

*
*
*
*
*
*

22.233

261
218
175
146
131
109

478
400
321
269
242
203

545
455
365
305
275
229

19.500

*
*
*
*
*
*

22.075

373
311
250
208
188
157

719
602
484
405
366
306
19.500

*
*
*
*
*
*

21.882

545
455
365
305
275
229
21.412

65
95
152
373
*
*
*
*
* 240 *
54
79
127
311
*
*
*
*
* 201 *
43
63
102
250
*
*
*
* 161 *
*
36
53
85
208
*
*
*
* 135 *
*
32
47
77
188
*
*
*
* 121 *
*
27.4
39
64
157
*
*
*
* 101 *
*
C-46 C-46 C-46 C-46 C-46 C-46 C-46 C-46 C-48 C-48 C-48 C-48 C-48
C-72 C-72 C-72 C-72 C-72 C-72 C-72 C-72 C-74 C-74 C-74 C-74 C-74
C-88 C-88 C-88 C-88 C-88 C-88 C-88 C-88 C-90 C-90 C-90 C-90 C-90

545
455
365
305
275
229
C-48
C-74
C-90

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
22
32
40
49
56
69
73
89
103
119
139
165
175
209
1800
1
55
85
108
136
165
205
213
259
317
368
375
445
617
736
Double
22
31
40
48
55
69
74
89
104
120
142
167
181
213
Reduction 1500
1
48
74
96
120
146
182
192
231
287
330
341
401
567
668
Horizontal
21
30
39
47
54
67
73
87
104
119
142
165
183
213
1200
Type
1
41
64
83
103
127
157
169
201
254
290
303
353
507
593
20
29
38
45
53
64
71
84
102
116
140
162
181
210
1000
1
35
54
71
88
110
133
146
173
220
251
264
306
445
517
18
19
28
37
44
52
63
70
83
100
114
138
159
178
207

900
1
32
50
67
82
103
125
137
162
207
236
249
288
421
487
22.4
18
27
35
42
50
60
67
79
97
109
133
154
173
200
750
1
27
43
58
71
90
109
120
141
182
205
219
253
372
430

1800
Double
Reduction
Vertical
Type

18

22.4

1500
1200
1000
900
750
1800

Double
Reduction
Upright
Type

18

22.4

1500
1200
1000
900
750

C - 18

1
1
1
1
1
1

22
55
22
48
21
41
20
35
19
32
18
27

32
85
31
74
30
64
29
54
28
50
27
43

40
108
40
96
39
83
38
71
37
67
35
58

49
136
48
120
47
103
45
88
44
82
42
71

53
157
53
141
53
124
52
107
51
101
49
88

69
205
69
182
67
157
64
133
63
125
60
109

73
213
74
192
73
169
71
146
70
137
67
120

89
259
89
231
87
201
84
173
83
162
79
141

103
317
104
287
104
254
102
220
100
207
97
182

119
368
120
330
119
290
116
251
114
236
109
205

139
375
142
341
142
303
140
264
138
249
133
219

165
445
167
401
165
353
162
306
159
288
154
253

175
617
181
567
183
507
181
445
178
421
173
372

209
736
213
668
213
593
210
517
207
487
200
430

1
1
1
1
1
1

18
44
17
38
17
33
16
28
15
26
15
22

25
68
25
60
24
51
23
43
23
40
21
35

32
87
32
77
32
67
30
57
30
53
28
46

39
109
39
96
37
82
36
70
35
66
33
57

44
132
44
117
43
102
42
88
41
82
40
72

55
164
55
146
54
126
51
106
50
100
48
87

58
171
59
154
58
135
57
116
56
109
54
96

71
207
71
185
70
161
68
138
66
130
63
113

82
254
84
230
83
203
82
176
80
166
77
146

95
294
96
264
95
232
93
201
91
189
87
164

111
300
114
273
114
242
112
211
110
199
107
176

132
356
133
321
132
282
130
245
127
230
123
202

140
494
145
453
146
406
144
356
143
336
139
298

167
589
171
535
170
474
168
413
165
390
160
344

SELECTION Right Angle Shaft Double Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
17.625

18.000

17.895

803
689
571
490
448
384

1040
918
785
691
642
551

1590
1370
1130
975
892
765

19.123

19.529

20.471

771
662
548
470
431
369

1040
918
785
691
634
530

1480
1270
1050
905
829
711

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

C-50

C-50

C-50

Nominal Reduction Ratio 18 22.4

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

100
1800
83
1500
18
67
1200
56
1000
50
900
42
750
Exact Reduction Ratio
90
1800
75
1500
20
60
1200
50
1000
45
900
38
750
Exact Reduction Ratio
80
1800
67
1500
22.4
54
1200
45
1000
40
900
33
750
Horizontal
Dimension
Vertical
Tables
Upright

*Marked models are triple reduction units. Refer to C-20 and C-21.

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

1800 Double
1.00
20
1.00
490
1
Reduction
200
0.85
30
0.87
1500 Horizontal
538
560
570
1
0.70
220
270
40
0.73
Type
1200
525
599
590
1
0.55
50
0.60
210
280
320
1000
444
551
600
1
18
210
270
330
900

425
508
593
1
0QVGU
190
250
320
22.4
750
350
429
523
1
Size of Reducer

1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

Double

1500 Reduction
1200
1000
900

Vertical
Type

18

22.4

750

Double

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

18

22.4

750

C - 19

SELECTION Right Angle Shaft Triple Reduction

Nominal Reduction Ratio 20 25

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
90
1500
75
20
1200
60
1000
50
900
45
750
38
Exact Reduction Ratio
1800
80
1500
67
22.4
1200
54
1000
45
900
40
750
33
Exact Reduction Ratio
1800
72
1500
60
25
1200
48
1000
40
900
36
750
30
Horizontal
Dimension
Vertical
Tables
Upright

20.091

19.620

19.790

19.181

19.950

20.206

61
51
41
34
31
26.1

81
67
54
45
40
34

124
103
83
69
62
52

194
162
130
108
97
81

295
246
198
165
149
124

516
431
346
289
261
218

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

21.656

22.388

22.530

22.351

22.353

22.286

55
46
37
31
28.1
23.5

81
67
54
45
40
34

124
103
83
69
62
52

194
162
130
108
97
81

295
246
198
165
149
124

476
398
320
268
241
202

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

20.548

*
*
*
*
*
*

735
616
495
413
373
311
22.353

*
*
*
*
*
*

696
582
468
391
353
295

25.137 25.041 24.444

25.935 24.662 25.137

24.938

24.630 24.626 25.685

80
64
49
67
54
41
53
43
33
45
36
27.8
40
32
25.0
33
20.9 27.3
C-52 C-52 C-52
C-76 C-76 C-76
C-92 C-92 C-92

117 124 193

98 103 162
83 130
78
69 108
65
97
62
59
81
52
49
C-52 C-52 C-54
C-76 C-76 C-78
C-92 C-92 C-94

295
246
198
165
149
124
C-54
C-78
C-94

453 516 625

379 431 528
304 346 424
254 289 355
229 261 320
192 218 267
C-54 C-54 C-56
C-78 C-78 C-80
C-94 C-94

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
34
43
53
61
77
84
113
138
172 213
1800
Triple
1
65
86
93
141
178
177
214
368
459 510
Reduction
34
43
53
61
77
85
115
144
178 220
1500
1
58
77
83
126
159
160
195
340
421 468
Horizontal
33
43
52
60
76
85
115
146
180 222
Type
1200
1
51
67
72
111
139
141
173
307
377 419
33
42
50
59
74
83
114
145
178 220
1000
1
44
58
62
96
120
122
151
271
332 369
20
32
41
49
58
73
82
112
144
176 218
900

1
42
54
58
90
113
115
143
257
314 350
31
39
47
56
70
79
109
141
172 213
25
750
1
36
47
50
79
99
102
126
229
279 311

1800
Triple
Reduction
Vertical
Type

20

25

1500
1200
1000
900
750
1800

Triple
Reduction
Upright
Type

20

25

1500
1200
1000
900
750

C - 20

1
1
1
1
1
1

31
61
32
55
32
49
32
43
31
40
30
36

41
81
42
74
41
65
41
56
40
53
38
47

51
89
51
80
51
70
49
60
48
57
46
50

57
133
59
121
59
107
58
93
57
88
55
78

73
169
74
153
74
135
72
117
71
110
69
97

79
166
81
152
82
136
81
119
80
113
78
100

105
200
109
185
111
167
111
147
110
139
107
124

126
336
135
319
140
293
141
262
140
250
138
224

159
422
168
397
172
362
173
321
172
306
169
273

1
1
1
1
1
1

34
65
34
58
33
51
33
44
32
42
31
36

43
86
43
77
43
67
42
58
41
54
39
47

55
96
55
85
54
74
52
64
51
60
49
52

61
141
61
126
60
111
59
96
58
90
56
79

77
178
77
159
76
139
74
120
73
113
70
99

84
177
85
160
85
141
83
122
82
115
79
102

113
214
115
195
115
173
114
151
112
143
109
126

138
368
144
340
146
307
145
271
144
257
141
229

172
459
178
421
180
377
178
332
176
314
172
279

181
433
195
416
205
386
207
346
207
331
205
298

SELECTION Right Angle Shaft Triple Reduction

Nominal Reduction Ratio 20 25

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
r/min
r/min
Ratio

Size of Reducer

*
*
*
*
*
*

20.504

19.608

992
829
666
556
501
419

1520
1270
1020
856
772
645

*
*
*
*
*
*

*
*
*
*
*
*

22.800 22.004 22.444 22.499 22.222

735
616
495
413
373
311

992
829
666
556
501
419

992 1360 1520

829 1160 1270
666 936 1020
556 783 856
501 706 772
419 591 645

24.737 25.271 24.351 24.166 25.421 24.837

714 912 992 1270 1360 1520

613 763 829 1090 1170 1270
495 613 666 910 970 1020
413 513 556 771 827 856
373 462 501 696 746 772
311 386 419 582 624 645
C-56 C-56 C-56 C-56 C-56 C-58
C-80 C-80 C-80 C-80 C-80

Exact Reduction Ratio

90
1800
75
1500
20
60
1200
50
1000
45
900
38
750
Exact Reduction Ratio
80
1800
67
1500
22.4
54
1200
45
1000
40
900
33
750
Exact Reduction Ratio
72
1800
60
1500
25
48
1200
40
1000
36
900
30
750
Horizontal
Dimension
Vertical
Tables
Upright

*marked models are double reduction units. Refer to C-18 and C-19.

239
572
246
524
249
469
247
413
244
391
239
348

273
767
282
705
286
634
284
558
281
530
275
472

306
860
317
792
321
711
319
627
316
595
309
530

348 385
933 1031
366 402
874 958
375 410
794 869
375 410
703 769
373 408
669 732
366 400
599 654

203
485
219
466
229
433
232
388
232
371
229
334

230
646
249
624
262
582
266
524
266
502
264
453

258
724
280
700
294
653
299
588
299
563
296
508

280
750
315
751
340
719
349
655
351
630
350
571

316
847
350
834
373
791
382
717
384
689
382
625

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9118 9121 9126 9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

426
1800
1.00
20
1.00
703
1
Triple
443
0.85
30
0.87
1500 Reduction
730
1
Horizontal
0.70
450
40
0.73
1200
Type
743
1
0.55
50
0.60
449
1000
741
1
20
446

900
736
1
25
0QVGU
437
750
722
1

Size of Reducer
9095 9100 9105 9110 9115

0QVGU

1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

Triple

1500 Reduction
1200
1000
900

Vertical
Type

20

25

750

Triple
1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

20

25

750

C - 21

SELECTION Right Angle Shaft Triple Reduction

Nominal Reduction Ratio 28 35.5

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
65
1500
54
28
1200
43
1000
36
900
32
750
27
Exact Reduction Ratio
1800
57
1500
48
31.5
1200
38
1000
32
900
29
750
24
Exact Reduction Ratio
1800
51
1500
42
35.5
1200
34
1000
28
900
25
750
21
Horizontal
Dimension
Vertical
Tables
Upright

27.096 27.225 27.893 28.379 29.526 27.706 29.291 27.509 27.941 27.718 27.165 27.041 27.941

44
37
29.9
25.0
22.5
18.8

58
49
39
33
29.7
24.8

65
55
44
36
33
28

81
67
54
45
40
34

96
80
64
54
48
40

124
103
83
69
62
52

152
127
102
85
77
64

194
162
130
108
97
81

251
210
168
141
127
106

295
246
198
165
149
124

392
328
263
220
198
166

498
417
335
280
252
211

559
468
376
314
283
237

32.455 31.331 31.694 31.079 31.969 32.319 30.157 31.521 31.129 30.875 32.280 30.017 32.063

32
26.9
21.5
18.0
16.2
13.5

51
43
34
29.1
26.2
21.9

57
48
38
32
29
24.1

81
67
54
45
40
34

92
79
64
53
48
40

124
103
83
69
62
52

140
117
94
78
70
59

194
162
130
108
97
81

225
190
152
127
114
95

295
246
198
165
149
124

331
280
224
187
169
141

473
399
321
268
242
202

508
425
341
285
257
215

34.983 34.063 36.165 35.357 36.395 36.309 35.140 36.050 34.879 34.647 35.603 32.960 34.879

78 100 127 159 202 266 301 410 450

69
51
47
32
84 106 133 169 223 251 343 376
65
57
42
39
26.9
85 106 135 179 202 276 302
67
52
46
34
31
21.5
89 113 149 169 230 253
71
56
44
38
29
18.0 26.4
80 102 134 152 208 228
64
50
39
34
16.2 23.8 25.7
85 112 127 173 190
67
53
42
33
13.5 19.9 21.5 29.2
C-52 C-52 C-52 C-52 C-52 C-52 C-54 C-54 C-54 C-54 C-54 C-54 C-56
C-76 C-76 C-76 C-76 C-76 C-76 C-78 C-78 C-78 C-78 C-78 C-78 C-80
C-92 C-92 C-92 C-92 C-92 C-92 C-94 C-94 C-94 C-94 C-94 C-94

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
31
40
49
59
58
74
81
99
109
136
137
168 210
1800
1
59
79
85
103
135
171
172
209
208
259
364
447 502
Triple
30
40
48
58
58
73
81
100
110
138
139
172 212
Reduction 1500
1
52
71
75
90
120
152
153
188
186
233
328
408 452
Horizontal
29
39
46
57
57
72
80
98
108
136
138
173 211
1200
Type
1
44
61
64
79
104
132
133
163
162
205
289
364 398
28
38
44
55
55
70
78
96
106
134
135
172 207
1000
1
38
53
54
67
89
114
115
142
140
178
251
319 346
28
27
37
43
54
53
69
76
94
104
132
133
170 204

900
1
35
50
51
63
83
106
108
133
132
168
236
302 327
35.5
26
36
41
51
51
66
73
91
100
128
128
165 198
750
1
30
43
44
54
72
93
94
117
116
148
208
268 288

1800
Triple
Reduction
Vertical
Type

28

35.5

1500
1200
1000
900
750
1800

Triple
Reduction
Upright
Type

28

35.5

1500
1200
1000
900
750

C - 22

1
1
1
1
1
1

30
57
29
50
28
43
27
37
27
34
25
30

38
75
38
68
38
60
37
52
37
49
35
43

47
82
47
72
45
62
44
54
43
50
41
43

56
98
56
87
55
76
54
66
53
62
51
54

56
129
56
115
55
101
54
87
52
81
50
71

70
163
71
146
70
128
69
111
67
105
65
92

77
162
78
147
78
129
76
112
75
105
72
92

94
198
96
180
95
158
94
139
92
130
89
115

103
196
105
178
105
157
103
137
102
129
98
114

128
244
132
222
132
198
131
174
129
164
126
146

128
341
132
313
133
279
131
244
130
231
126
204

156
415
163
386
167
351
167
310
165
295
162
263

1
1
1
1
1
1

31
59
30
52
29
44
28
38
27
35
26
30

40
79
40
71
39
61
38
53
37
50
36
43

51
90
50
78
49
67
47
57
45
53
43
46

59
103
58
90
57
79
55
67
54
63
51
54

58
135
58
120
57
104
55
89
53
83
51
72

74
171
73
152
72
132
70
114
69
106
66
93

81
172
81
153
80
133
78
115
76
108
73
94

99
209
100
188
98
163
96
142
94
133
91
117

109
208
110
186
108
162
106
140
104
132
100
116

136
259
138
233
136
205
134
178
132
168
128
148

137
364
139
328
138
289
135
251
133
236
128
208

168
447
172
408
173
364
172
319
170
302
165
268

180
430
194
412
198
373
197
330
196
313
191
279

SELECTION Right Angle Shaft Triple Reduction

Nominal Reduction Ratio 28 35.5

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
r/min
r/min
Ratio

Size of Reducer

Exact Reduction Ratio

65
1800
54
1500
28
43
1200
36
1000
32
900
27
750
32.716 30.012 31.413 31.331 31.500 30.922 30.922
31.729 31.729 Exact Reduction Ratio
708 877 988 1140 1380 1780 1920
2730 2910
57
1800

592 734 823 978 1150 1490 1640

2280 2500
48
1500
476 590 658 806 923 1200 1360
1840 2070
31.5
38
1200
1530 1770
398 493 548 674 769 1000 1160
32
1000
1380 1620
359 445 494 608 692 906 1050
29
900
1160 1360
300 372 411 508 576 758 882
24
750
35.108 35.811 36.045 35.601 36.176 36.000 36.000 36.500 35.036 35.036 Exact Reduction Ratio
630 766 878 988 1330 1530 1690 2110 2480 2680
51
1800
527 640 734 823 1110 1280 1450 1760 2070 2300
42
1500
424 514 590 658 895 1030 1200 1420 1670 1910
35.5
34
1200
354 430 493 548 748 866 1000 1180 1390 1630
28
1000
319 388 445 494 675 780 908 1070 1260 1480
25
900
267 324 372 411 564 652 759 895 1050 1240
21
750
C-56 C-56 C-56 C-56 C-58 C-58 C-58 C-60 C-60 C-60 Horizontal
Dimension
C-80 C-80 C-80 C-80
Vertical
Tables
Upright

28.500 27.119 27.662 27.730 27.389

625
536
444
379
341
285
30.922

589
498
400
335
302
252
35.576

522
448
364
304
274
229
C-56
C-80

812
679
546
456
411
344

970 1130 1280

825 949 1090
663 763 910
554 638 781
500 575 715
418 481 612

28.500 28.500

27.737 27.737

1930 2060
1610 1770
1300 1460
1080 1250
982 1140
821 955

3110 3260
2600 2800
2090 2320
1750 1990
1580 1820
1320 1560

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
272
764
275
688
274
607
269
529
265
499
257
441

298
839
303
758
300
666
294
579
290
546
281
481

340 376
912 1007
348 389
830 929
348 390
736 825
343 383
643 719
338 378
607 679
329 367
538 600

200
477
212
450
215
405
213
357
211
338
206
300

232
651
251
627
256
569
256
503
254
478
248
426

255
717
274
685
282
627
281
552
278
524
272
466

280
750
310
738
324
686
325
609
323
580
317
519

315
844
343
819
363
768
365
684
362
651
355
581

417
688
428
706
431
712
428
706
424
700
415
684

500
824
529
872
546
901
543
895
538
888
526
868

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
229
547
230
490
228
430
223
373
220
352
213
310

0QVGU

500
824
529
872
546
901
543
895
538
888
526
868

455
751
488
805
509
841
516
851
516
851
511
843

537
886
586
966
619
1021
630
1040
629
1038
622
1026

537
886
586
966
619
1021
630
1040
629
1038
622
1026

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
Ratio
r/min
Fans

Without Fan With Fan

1800
1.00
20
1.00
1
Triple
0.85
30
0.87
1500 Reduction
1
Horizontal
0.70
40
0.73
1200
Type
1
0.55
50
0.60
1000
1
28

900
1
35.5
0QVGU
750
1
1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

Triple

1500 Reduction
1200
1000
900

Vertical
Type

28

35.5

750

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

28

35.5

750

C - 23

SELECTION Right Angle Shaft Triple Reduction

Nominal Reduction Ratio 40 50

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
45
1500
38
40
1200
30
1000
25
900
23
750
19
Exact Reduction Ratio
1800
40
1500
33
45
1200
27
1000
22
900
20
750
17
Exact Reduction Ratio
1800
36
1500
30
50
1200
24
1000
20
900
18
750
15
Horizontal
Dimension
Vertical
Tables
Upright

40.607 40.451 39.487 40.296 41.895 39.838 39.520 37.815 38.912 38.541 39.346 39.341 40.078

30
25.8
20.7
17.3
15.6
13.0

32
26.9
21.5
18.0
16.2
13.5

50
41
33
28.0
25.3
21.1

57
48
38
32
28.9
24.1

73
61
49
40
36
30

92
79
65
56
51
42

124
103
83
69
62
52

140
117
94
78
70
59

194
162
130
109
98
82

225
190
152
127
114
95

286
239
192
160
144
121

331
280
224
187
169
141

408
341
274
229
206
172

43.770 43.979 45.058 45.843 47.695 44.756 46.051 43.250 43.599 43.250 43.397 43.198 43.599

27.8
23.2
18.6
15.6
14.0
11.7

32
26.9
21.5
18.0
16.2
13.5

41
34
28
23.0
20.7
17.3

51.141 50.611

53
44
35
30
27.0
22.6

60
50
40
33
30
25.3

82
68
55
46
41
34

97
81
65
54
49
41

133
111
89
74
67
56

162
135
108
91
82
68

214
179
144
120
108
90

248
207
166
139
125
104

315
263
211
176
159
133

362
302
243
203
183
152

50.205 51.869 52.207 50.273 49.557 49.500 48.176 48.889 47.953 50.984

97 130 153 199 231 295 322

78
59
51
32
19.3
81 110 128 170 193 252 269
65
49
42
16.1 26.9
88 102 137 155 202 216
65
52
39
34
12.9 21.5
86 115 129 169 180
73
54
43
33
28.6
10.8 18.0
77 103 116 152 162
66
49
39
25.7 39.9
9.7 16.2
97 127 136
86
64
55
41
32
21.4 24.9
8.1 13.5
C-52 C-52 C-52 C-52 C-52 C-52 C-54 C-54 C-54 C-54 C-54 C-54 C-56
C-76 C-76 C-76 C-76 C-76 C-76 C-78 C-78 C-78 C-78 C-78 C-78 C-80
C-92 C-92 C-92 C-92 C-92 C-92 C-92 C-92 C-92 C-92 C-92 C-92

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
26
37
44
54
53
67
74
91
102
126
129
159 196
1800
1
51
73
76
94
123
155
155
192
194
240
342
422 468
Triple
26
36
42
53
52
66
73
90
101
125
128
159 195
Reduction 1500
1
44
63
66
83
108
136
136
169
171
212
304
376 415
Horizontal
24
34
40
51
50
64
70
87
98
122
126
156 191
1200
Type
1
37
54
55
70
92
117
117
145
147
184
264
328 360
23
33
38
49
48
61
68
85
95
119
122
152 186
1000
1
31
46
46
60
78
100
100
126
126
158
227
283 310
40
22
32
37
48
47
60
66
83
93
117
120
149 182

900
1
29
42
43
57
73
93
93
117
118
148
213
266 291
50
21
30
34
45
45
57
63
79
89
112
115
144 175
750
1
24
36
37
48
63
81
81
102
103
130
186
233 255

1800
Triple
Reduction
Vertical
Type

40

50

1500
1200
1000
900
750
1800

Triple
Reduction
Upright
Type

40

50

1500
1200
1000
900
750

C - 24

1
1
1
1
1
1

26
49
25
43
24
36
23
30
22
28
20
24

36
71
35
62
34
53
32
45
31
42
30
36

43
74
41
64
39
54
37
46
36
42
34
36

53
93
52
81
50
69
48
59
47
55
45
48

51
119
51
105
49
90
48
77
46
72
44
62

64
149
64
132
62
114
60
98
59
92
56
80

71
149
70
132
69
115
67
98
65
92
62
80

87
184
87
163
85
142
83
123
81
115
78
100

98
186
98
165
96
144
93
124
91
116
87
101

121
229
121
205
119
179
117
155
115
146
110
128

123
326
124
293
122
257
120
223
117
209
113
184

151
401
153
362
152
319
149
277
147
261
142
230

1
1
1
1
1
1

26
51
26
44
24
37
23
31
22
29
21
24

37
73
36
63
34
54
33
46
32
42
30
36

47
83
47
72
45
62
43
53
42
49
40
42

54
95
53
83
51
71
49
60
48
56
45
48

53
123
52
108
50
92
48
78
47
73
45
63

67
155
66
136
64
117
61
100
60
93
57
81

74
155
73
136
70
117
68
100
66
93
63
81

91
192
90
169
87
145
85
126
83
117
79
102

102
194
101
171
98
147
95
126
93
118
89
103

126
240
125
212
122
184
119
158
117
148
112
130

129
342
128
304
126
264
122
227
120
213
115
186

159
422
159
376
156
328
152
283
149
266
144
233

179
427
182
387
182
343
179
299
176
282
170
248

SELECTION Right Angle Shaft Triple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 40 50

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

45
1800
38
1500
40
30
1200
25
1000
23
900
19
750
43.878 45.882 45.529 45.529 46.162 44.206 44.206 Exact Reduction Ratio
861 1050 1220 1390 1670 1970 2200
40
1800
739 882 1020 1190 1400 1650 1890
33
1500
610 709 822 957 1120 1330 1560
45
27
1200
508 593 687 800 943 1110 1310
22
1000
457 534 620 721 850 1000 1180
20
900
381 446 518 603 710 838 988
17
750
50.194 49.040 49.398 49.398 50.084 50.569 50.569 Exact Reduction Ratio
755 988 1120 1290 1540 1730 1970
36
1800
632 827 945 1090 1290 1450 1690
30
1500
507 664 759 883 1040 1160 1370
50
24
1200
424 555 634 738 870 974 1140
20
1000
382 500 572 666 785 878 1030
18
900
319 416 478 556 656 734 866
15
750
C-56 C-58 C-58 C-58 C-60 C-60 C-60 Horizontal
Dimension
C-80
Vertical
Tables
Upright

38.599 40.322 38.853 38.716 40.726 38.824 39.059 39.059 39.601 40.079 40.079

479
401
322
269
242
202

577
483
388
324
292
244

682
570
458
383
345
288

861
723
581
486
438
366

44.471 43.271 44.136 44.425

430
364
292
244
220
184

514
429
345
288
260
217

624
522
419
350
315
264

715
598
480
402
362
302

48.249 50.875 47.886 48.680

385 459 555

322 384 464
258 308 373
216 257 312
194 232 281
162 194 234
C-56 C-56 C-56
C-80 C-80 C-80

691
578
464
388
349
292
C-56
C-80

917 1240 1420 1570 1940 2170 2390

775 1030 1180 1350 1630 1820 2050
623 835 955 1110 1310 1460 1700
521 698 799 930 1090 1220 1440
469 630 720 839 988 1100 1300
392 526 602 701 826 923 1080

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
258
724
257
642
252
558
245
482
240
453
232
397

285
801
287
717
283
629
277
545
273
514
264
453

330
885
335
798
330
700
323
606
317
570
306
501

362
969
365
870
362
767
356
667
351
630
340
556

197
471
203
432
205
387
203
340
201
322
196
286

233
656
239
599
239
531
236
463
232
438
225
386

256
720
265
661
268
594
265
522
263
495
256
439

291
779
305
727
312
661
310
581
306
550
298
487

322
862
335
799
341
721
340
637
337
605
330
539

399
658
401
662
397
655
389
642
383
633
372
613

524
864
529
872
525
866
516
852
509
840
495
817

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
219
524
220
468
217
410
213
356
209
335
202
295

0QVGU

524
864
529
872
525
866
516
852
509
840
495
817

450
743
481
793
490
809
490
808
487
803
478
788

552
911
586
966
593
978
590
973
585
965
573
945

552
911
586
966
593
978
590
973
585
965
573
945

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
Ratio
r/min
Fans

Without Fan With Fan

1800
1.00
20
1.00
1
Triple
0.85
30
0.87
1500 Reduction
1
Horizontal
0.70
40
0.73
1200
Type
1
0.55
50
0.60
1000
1
40

900
1
50
0QVGU
750
1
1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

Triple

1500 Reduction
1200
1000
900

Vertical
Type

40

50

750

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

40

50

750

C - 25

SELECTION Right Angle Shaft Triple Reduction

Nominal Reduction Ratio 56 71

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
32
1500
27
56
1200
21
1000
18
900
16
750
13
Exact Reduction Ratio
1800
29
1500
24
63
1200
19
1000
16
900
14
750
12
Exact Reduction Ratio
1800
25
1500
21
71
1200
17
1000
14
900
13
750
11
Horizontal
Dimension
Vertical
Tables
Upright

55.125 55.025 56.987 57.115 59.051 58.652 58.582 56.678 55.462 54.062 53.922 52.655 55.462

19.3
16.1
12.9
10.8
9.7
8.1

29.4
24.6
19.7
16.5
14.8
12.4

31
26.1
20.9
17.5
15.7
13.1

63.986

62.222

19.3
16.1
12.9
10.8
9.7
8.1

31
26.1
20.9
17.5
15.7
13.1

43
36
28.9
24.1
21.7
18.1

48
40
32
27.3
24.6
20.5

62
52
42
35
31
26.5

77
64
51
43
38
32

102
85
68
57
51
43

128
107
85
71
64
54

172
144
115
96
87
72

200
167
134
112
101
84

259
216
174
145
131
109

285
238
191
160
144
120

64.640 64.637 63.984 63.041 63.000 61.286 62.222 59.583 64.889

47
39
31
26.6
24.0
20.0

63
52
42
35
31
26.6

75
63
50
42
38
31

97
81
65
54
49
41

111
92
74
62
55
46

156
132
106
88
80
66

172
143
115
96
86
72

238
202
162
135
122
102

254
212
170
142
128
107

68.971 69.300 71.000 72.237 73.590 72.617 74.559 72.101 70.588 68.773 68.627 65.425 70.588

80 101 135 158 209 225

60
50
39
31
26
17.7 19.3
84 113 132 175 188
67
50
42
32
14.8 16.1 21.9 26.1
91 105 140 151
67
53
40
34
11.9 12.9 17.5 20.9 26.3
88 117 126
76
56
45
34
9.9 10.8 14.6 17.5 21.9 28.5
79 105 113
68
50
40
30
9.7 13.2 15.7 19.7 25.6
8.9
95
88
66
57
42
33
8.1 11.0 13.1 16.5 21.4 25.6
7.4
C-52 C-52 C-52 C-52 C-52 C-52 C-54 C-54 C-54 C-54 C-54 C-54 C-56
C-76 C-76 C-76 C-76 C-76 C-76 C-78 C-78 C-78 C-78 C-78 C-78 C-80
C-92 C-92 C-92 C-92 C-92 C-92 C-94 C-94 C-94 C-94 C-94 C-94

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
25
31
41
48
49
64
68
86
93
121
118
153 182
1800
1
48
62
71
84
114
148
143
181
177
230
314
408 436
Triple
24
30
39
46
48
62
66
84
91
119
116
152 180
Reduction 1500
1
41
53
61
72
98
129
124
158
154
202
276
359 382
Horizontal
23
28
37
44
46
60
63
81
88
115
113
148 174
1200
Type
1
35
44
51
61
83
109
106
135
132
173
237
310 328
22
27
35
41
43
57
61
78
84
111
109
143 168
1000
1
29
37
43
50
70
93
89
115
112
148
202
266 281
56
21
26
34
40
42
56
59
76
82
109
106
140 164

900
1
27
34
40
47
65
86
83
107
104
138
189
249 262
71
19
24
32
37
40
53
56
72
78
103
101
134 156
750
1
23
29
34
39
56
74
72
93
90
120
164
217 228

1800
Triple
Reduction
Vertical
Type

56

71

1500
1200
1000
900
750
1800

Triple
Reduction
Upright
Type

56

71

1500
1200
1000
900
750

C - 26

1
1
1
1
1
1

24
47
24
40
22
34
21
29
21
27
19
23

30
60
29
52
28
43
26
36
25
34
24
29

40
69
38
60
37
50
35
43
34
39
32
34

47
82
45
70
43
59
41
50
39
46
37
39

47
110
46
96
45
82
43
69
42
65
39
55

62
143
61
125
59
107
56
91
55
85
52
74

65
138
64
121
62
103
60
88
58
82
55
71

83
175
82
154
80
133
77
114
75
106
72
93

90
171
89
150
86
129
83
110
81
103
77
89

117
222
116
196
113
170
109
146
107
136
102
119

113
301
113
267
110
232
107
199
104
186
100
162

147
391
147
348
144
303
140
261
138
245
132
215

1
1
1
1
1
1

25
48
24
41
23
35
22
29
21
27
19
23

31
62
30
53
28
44
27
37
26
34
24
29

43
74
41
64
39
54
37
45
36
42
33
36

48
84
46
72
44
61
41
50
40
47
37
39

49
114
48
98
46
83
43
70
42
65
40
56

64
148
62
129
60
109
57
93
56
86
53
74

68
143
66
124
63
106
61
89
59
83
56
72

86
181
84
158
81
135
78
115
76
107
72
93

93
177
91
154
88
132
84
112
82
104
78
90

121
230
119
202
115
173
111
148
109
138
103
120

118
314
116
276
113
237
109
202
106
189
101
164

153
408
152
359
148
310
143
266
140
249
134
217

169
405
170
361
167
315
162
272
159
255
153
223

SELECTION Right Angle Shaft Triple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 56 71

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

32
1800
27
1500
56
21
1200
18
1000
16
900
13
750
63.843 60419 61.300 63.112 61.661 61.378 61.378 63.115 63.459 63.459 Exact Reduction Ratio
367 442 548 603 763 913 1060 1230 1380 1620
29
1800
307 369 456 504 638 763 888 1030 1160 1360
24
1500
246 296 365 405 512 613 713 829 932 1100
63
19
1200
206 248 304 338 427 512 596 693 779 919
16
1000
185 223 274 305 384 462 537 625 702 828
14
900
155 186 228 255 320 386 449 522 587 692
12
750
68.512 69.882 70.339 69.474 72.872 70.500 70.500 73.000
Exact Reduction Ratio
327 397 456 548 660 797 927 1070 *
25
1800
*
273 332 381 456 550 666 775 895 *
21
1500
*
219 266 305 365 440 535 622 719 *
71
17
1200
*
183 222 255 304 367 447 520 601
14
1000
*
*
165 200 230 274 330 403 469 541
13
900
*
*
138 167 192 228 275 336 391 452
11
750
*
*
C-56 C-56 C-56 C-56 C-58 C-58 C-58 C-60 C-60 C-60 Horizontal
Dimension
C-80 C-80 C-80 C-80
Vertical
Tables
Upright

56.571 54.596 55.688 55.858 55.170 57.957 56.571 56.571 58.172 55.474 55.474

344
287
231
193
173
145
61.378

304
254
204
170
153
128
72.000

271
226
182
152
137
114
C-56
C-80

409
342
274
229
206
172

497
415
333
278
251
209

571
478
383
320
289
241

706
588
470
392
353
294

839
702
563
471
424
354

989 1150 1330 1580 1820

827 962 1110 1320 1560
664 773 899 1060 1250
555 646 751 889 1040
500 582 677 802 946
418 487 566 670 790

marked models are quadruple reduction units. Refer to C-30 and C-31.

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
243
683
240
600
233
517
225
443
220
415
211
361

267
750
263
657
255
565
246
483
240
452
230
394

306
821
303
723
296
626
287
537
281
504
269
440

344
921
339
810
330
698
319
599
313
561
300
490

184
441
184
391
180
340
175
293
172
275
164
240

225
633
226
566
223
495
218
429
214
403
206
353

249
699
249
623
245
543
238
469
234
440
225
386

283
757
285
680
283
598
277
519
272
489
263
430

319
855
321
765
317
670
309
580
304
546
293
479

387
639
385
634
376
621
366
604
359
593
346
571

489
806
483
797
470
776
456
752
447
737
430
709

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
197
472
194
412
187
353
180
302
176
282
168
245

0QVGU

489
806
483
797
470
776
456
752
447
737
430
709

454
748
457
754
452
746
443
731
437
720
423
697

554
914
562
928
561
925
553
912
546
900
530
875

554
914
562
928
561
925
553
912
546
900
530
875

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
Ratio
r/min
Fans

Without Fan With Fan

1800
1.00
20
1.00
1
Triple
0.85
30
0.87
1500 Reduction
1
Horizontal
0.70
40
0.73
1200
Type
1
0.55
50
0.60
1000
1
56

900
1
71
0QVGU
750
1
1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

Triple

1500 Reduction
1200
1000
900

Vertical
Type

56

71

750

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

56

71

750

C - 27

SELECTION Right Angle Shaft Triple Reduction

Nominal Reduction Ratio 80 90

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

23
1800
19
1500
80
15
1200
13
1000
11
900
9.4
750
Exact Reduction Ratio
20
1800
17
1500
90
13
1200
11
1000
10
900
8.3
750
Horizontal
Dimension
Vertical
Tables
Upright

79.751

79.111

80.552

80.234

78.000

19.3
16.1
12.9
10.8
9.7
8.1

31
26.1
20.9
17.5
15.7
13.1

51
42
34
28.5
25.7
21.4

75
63
50
42
38
31

111
92
74
62
55
46

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

86.706

90.000

90.496

91.765

87.529

18.8
15.7
12.6
10.5
9.4
7.9
C-52
C-76
C-92

27.5
23.0
18.4
15.4
13.8
11.6
C-52
C-76
C-92

41
34
27.4
22.9
20.6
17.2
C-52
C-76
C-92

63
53
42
35
32
26.7
C-54
C-78
C-94

107
89
71
59
54
45
C-54
C-78
C-94

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

75.833 77.090

*
*
*
*
*
*

172
143
115
96
86
72

206
172
138
115
104
87

83.268

*
*
*
*
*
*

165
*
138
*
110
*
92
*
83
*
69
*
C-54 C-56
C-78 C-80
C-94

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
30
46
59
79
110
140 185
1800
1
59
81
136
167
210
372 443
Triple
29
44
57
77
108
137 183
Reduction 1500
1
51
69
117
145
182
325 388
Horizontal
27
42
54
73
103
132 177
1200
Type
1
42
58
99
122
155
278 334
25
39
51
70
99
127 171
1000
1
35
48
83
103
131
237 285
80
24
38
50
68
96
124 167

900
1
33
45
77
96
122
221 267
90
23
36
47
64
91
118 159
750
1
28
38
66
82
105
191 232

1800
Triple
Reduction
Vertical
Type

80

90

1500
1200
1000
900
750
1800

Triple
Reduction
Upright
Type

80

90

1500
1200
1000
900
750

C - 28

1
1
1
1
1
1

29
58
28
50
27
42
25
35
24
32
23
27

45
79
43
67
41
57
39
48
38
45
35
37

57
132
56
115
53
97
51
82
49
76
46
66

76
160
75
141
72
120
69
102
67
95
63
81

107
203
105
178
101
152
97
129
95
121
90
104

135
359
134
316
130
272
125
233
122
218
117
189

1
1
1
1
1
1

30
59
29
51
27
42
25
35
24
33
23
28

46
81
44
69
42
58
39
48
38
45
36
38

59
136
57
117
54
99
51
83
50
77
47
66

79
167
77
145
73
122
70
103
68
96
64
82

110
210
108
182
103
155
99
131
96
122
91
105

140
372
137
325
132
278
127
237
124
221
118
191

173
412
173
367
170
320
165
276
162
259
156
227

SELECTION Right Angle Shaft Triple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
78.118 77.451 75.820 83.128 79.474 77.647 76.490 76.490 79.203

240
200
160
134
121
101

290
242
194
162
146
122

85.313

353
295
237
198
178
149

386
323
259
216
195
163

85.712

481
402
323
269
243
203

587
490
393
328
296
247

735
615
493
412
372
310

856
716
574
480
432
361

988
826
663
554
499
417

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

93.924 91.765

220
* 313 * 408
183
262
341
*
*
147
210
273
*
*
123
175
228
*
*
111
158
206
*
*
92
132
172
*
*
C-56 C-56 C-56 C-56 C-56
C-80 C-80 C-80 C-80 C-80

512 *
*
*
427
*
*
*
341
*
*
*
284
*
*
*
256
*
*
*
213
*
*
*
C-58 C-58 C-58 C-60

Nominal Reduction Ratio 80 90

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

23
1800
19
1500
80
15
1200
13
1000
11
900
9.4
750
Exact Reduction Ratio
20
1800
17
1500
90
13
1200
11
1000
10
900
8.3
750
Horizontal
Dimension
Vertical
Tables
Upright

* marked models are quadruple reduction units. Refer to C-30 and C-31.

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126
197
471
194
412
187
353
180
301
176
282
168
244

245
689
242
605
235
521
227
447
222
418
213
364

263
738
259
647
251
556
242
476
237
445
226
388

304
814
300
717
293
619
284
532
278
499
267
436

330
885
326
778
317
671
307
575
300
539
288
470

184
440
184
391
180
340
175
292
171
274
164
239

228
640
229
572
225
500
220
433
216
407
208
357

245
689
245
613
241
535
235
462
230
433
221
380

281
753
283
675
280
593
274
515
270
484
261
426

308
825
309
737
304
644
297
558
292
524
282
460

363
599
357
590
346
571
335
553
328
540
314
517

487
803
481
793
468
772
454
749
445
734
427
705

487
803
481
793
468
772
454
749
445
734
427
705

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

447
1800
1.00
20
1.00
737
1
Triple
450
0.85
30
0.87
1500 Reduction
742
1
Horizontal
0.70
445
40
0.73
1200
Type
734
1
0.55
50
0.60
436
1000
719
1
80
429

900
708
1
90
0QVGU
416
750
686
1
1
1
1
1
1
1

1800

1
1
1
1
1
1

1800

Triple
1500 Reduction
1200
1000
900

Vertical
Type

80

90

750

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

80

90

750

C - 29

SELECTION Right Angle Shaft Quadruple Reduction

Nominal Reduction Ratio 71 90

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
25
1500
21
71
1200
17
1000
14
900
13
750
11
Exact Reduction Ratio
1800
23
1500
19
80
1200
15
1000
13
900
11
750
9.4
Exact Reduction Ratio
1800
20
1500
17
90
1200
13
1000
11
900
10
750
8.3
Horizontal
Dimension
Vertical
Tables
Upright

*
*
*
*
*
*

*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

77.989

79.341

78.120

26
21
17
14
13
11

30
25.3
20.3
16.9
15.2
12.7

80
66
53
44
40
33

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

127
106
84
70
63
53

90.326

91.330

87.529

87.269

21.0
17.5
14.0
11.7
10.5
8.8
C-62
C-82
C-96

30
25.3
20.3
16.9
15.2
12.7
C-62
C-82
C-96

45
37
30
25.0
22.5
18.8
C-64
C-84
C-98

80
66
53
44
40
33
C-64
C-84
C-98

124
104
83
69
62
52
C-64
C-84
C-98

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

79.124

88.991

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

90.353

*
*
*
*
*
*

176
147
118
98
89
74
C-66
C-86

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple
Reduction
Horizontal
Type

71

90
Quadruple
Reduction
Vertical
Type

71

90
Quadruple
Reduction
Upright
Type

71

90

C - 30

1800
1500
1200
1000
900
750

40
40
39
38
37
36

50
49
47
45
44
42

70
69
66
63
62
59

94
93
90
87
85
82

119
118
115
112
109
105

157
157
155
151
149
143

1800
1500
1200
1000
900
750

44
43
41
40
39
37

54
52
49
47
45
43

75
73
69
66
64
60

103
99
95
91
88
84

130
127
121
116
113
108

175
171
165
159
155
148

1800
1500
1200
1000
900
750

43
43
42
41
40
38

50
49
47
45
44
41

70
68
66
63
62
59

94
93
90
87
85
81

118
117
115
111
109
105

SELECTION Right Angle Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 71 90

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

25
1800
*
21
1500
*
71
17
1200
*
14
1000
*
13
900
*
11
750
*
78.568 78.568 Exact Reduction Ratio

23
1800
* 1120 1320
941
1110
19
1500
*
755 891
80
15
1200
*
631 745
13
1000
*
569 671
11
900
*
475 560
9.4
750
*
91.022 87.371 87371 Exact Reduction Ratio
862 1010 1190
20
1800
720 848 1000
17
1500
578 680 803
90
13
1200
483 568 670
11
1000
435 512 604
10
900
363 428 505
8.3
750
C-70 C-70 C-70 Horizontal
Dimension
Vertical
Tables
Upright
68.889 68.889

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

88.676

*
*
*
*
*
*

254
212
170
142
128
106
C-66
C-86

89.695

*
*
*
*
*
*

379
316
254
212
191
159
C-66
C-86

91.800 91.800

*
*
*
*
*
*

*
*
*
*
*
*

615 715
514 598
412 480
344 401
310 361
259 301
C-68 C-68

1280 1510
1070 1260
860 1010
718 848
648 764
541 638

* marked models are triple reduction units. Refer to C-28 C-29.

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131
259
259
255
250
246
237

228
224
216
209
205
197

288
281
271
262
256
245

359
361
356
349
344
334

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
202
204
202
199
196
190

0QVGU

359
361
356
349
344
334

386
395
397
394
390
381

472
484
488
484
480
469

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9136
Ratio
r/min
Fans

Without Fan With Fan

472
1800 Quadruple
1.00
20
1.00
484
1500 Reduction
Horizontal
0.85
30
0.87
488
1200
Type
0.70
40
0.73
484
1000
71
480
900
0.55

50
0.60
469
750
90
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
71

900
90
750

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
71
900

750
90

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 31

SELECTION Right Angle Shaft Quadruple Reduction

Nominal Reduction Ratio 100 125

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
18
1500
15
100
1200
12
1000
10
900
9.0
750
7.5
Exact Reduction Ratio
1800
16
1500
13
112
1200
11
1000
8.9
900
8.0
750
6.7
Exact Reduction Ratio
1800
14
1500
12
125
1200
9.6
1000
8.0
900
7.2
750
6.0
Horizontal
Dimension
Vertical
Tables
Upright

99.259 99.158 103.97 98.871 102.71

20.1
16.8
13.5
11.2
10.1
8.4

26.0
21.7
17.4
14.5
13.0
10.8

29.8
24.9
19.9
16.6
15.0
12.5

30
25.3
20.3
16.9
15.2
12.7

97.650 96.720 96.444 96.432 103.82

78
65
52
43
39
33

45
37
30
25.0
22.5
18.8

80
66
53
44
40
33

118
99
79
66
59
49

127
106
84
70
63
53

160
133
107
89
80
67

113.26 112.81 118.37 111.08 119.69 112.41 109.41 108.54 106.37 105.89 112.94

16.5
13.8
11.0
9.2
8.3
6.9

22.0
18.4
14.7
12.3
11.1
9.2

24.5
20.4
16.4
13.7
12.3
10.3

30
25.3
20.3
16.9
15.2
12.7

38
31
25.5
21.3
19.2
16.0

45
37
30
25.0
22.5
18.8

65
54
43
36
33
27.5

80
66
53
44
40
33

102
85
68
57
51
43

127
106
84
70
63
53

141
118
95
79
71
59

122.72 126.20 130.09 129.57 127.97 128.80 127.97 120.90 126.39 117.54 129.78

90 124 128
80
60
45
38
30
16.3 20.4 23.9
75 104 107
66
50
37
32
13.6 17.0 19.9 25.3
86
83
60
53
40
30
10.6 13.6 16.0 20.3 26.0
71
69
50
44
33
9.1 11.4 13.3 16.9 21.7 25.0
64
62
45
40
30
8.2 10.2 12.0 15.2 19.6 22.5
53
52
38
33
8.5 10.0 12.7 16.3 18.8 25.2
6.8
C-62 C-62 C-62 C-62 C-64 C-64 C-64 C-64 C-64 C-64 C-66
C-82 C-82 C-82 C-82 C-84 C-84 C-84 C-84 C-84 C-84 C-86
C-96 C-96 C-96 C-96 C-98 C-98 C-98 C-98 C-98 C-98

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple 1800
39
45
46
57
64
78
87
107
110
135 147
Reduction 1500
38
44
45
55
63
76
86
105
109
133 147
Horizontal
36
42
43
53
60
72
83
102
106
129 144
1200
Type
35
40
41
50
58
69
80
98
103
125 140
1000
100
34
39
40
49
56
68
78
96
100
122 138

900
32
37
38
46
54
64
74
91
96
117 133
750
125
Quadruple
Reduction
Vertical
Type

100

125
Quadruple
Reduction
Upright
Type

100

125

C - 32

1800
1500
1200
1000
900
750

41
40
38
36
35
33

48
46
44
42
40
38

49
47
45
43
41
39

60
58
55
52
50
47

69
66
63
60
58
55

82
79
75
71
69
65

94
91
86
83
80
76

115
111
106
101
98
93

120
116
111
107
104
99

146
142
135
130
126
120

1800
1500
1200
1000
900
750

41
40
38
37
36
34

45
44
42
40
39
37

46
45
43
41
40
38

56
55
53
50
49
46

64
63
60
58
56
54

78
76
72
69
68
64

87
85
83
80
78
74

107
105
101
98
95
91

110
109
106
103
100
96

135
133
129
125
122
117

162
158
152
147
143
137

SELECTION Right Angle Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 100 125

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

18
1800
15
1500
100
12
1200
10
1000
9.0
900
7.5
750
112.18 110.36 110.36 Exact Reduction Ratio
702 806 951
16
1800
586 673 794
13
1500
470 540 637
112
11
1200
393 451 532 8.9
1000
354 406 480
8.0
900
295 339 400
6.7
750
121.72 126.25 126.25 Exact Reduction Ratio
648 706 833
14
1800
541 590 696
12
1500
434 473 558
125
9.6
1200
362 395 466
8.0
1000
327 356 420
7.0
900
273 297 350
6.0
750
C-70 C-70 C-70 Horizontal
Dimension
Vertical
Tables
Upright

99.991 101.85 98.135 97.789 101.65 98.060 99.600 99.600 98.756 99.948 99.948

188
157
126
105
94
79

232
194
155
129
117
97

274
229
184
153
138
115

348
290
233
194
175
146

401
335
269
224
202
169

500
418
335
280
252
210

567
474
380
318
286
239

660
552
443
370
333
278

115.20 109.29 111.48 112.21 110.83 113.61 115.20 115.20

170
142
114
95
86
71

206
172
138
115
104
86

251
209
168
140
126
105

287
240
192
161
145
121

368
308
247
206
186
155

433
362
290
242
218
181

492
411
329
275
248
207

572
478
383
320
288
241

124.99 124.14 120.95 119.20 126.78 123.87 124.99 124.99

151 191 223 286 304 397 454 528

126 159 186 239 253 332 349 441
101 127 149 191 203 266 304 354
84 106 124 160 170 222 254 295
96 112 144 153 200 229 266
76
94 120 127 167 191 222
80
63
C-66 C-66 C-66 C-66 C-66 C-68 C-68 C-68
C-86 C-86 C-86 C-86 C-86

796
665
534
446
402
335

889 1040
742 876
596 703
498 587
448 529
374 442

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131
189
190
188
184
181
176

211
212
209
205
202
195

252
250
245
239
235
227

275
273
268
261
256
247

180
176
169
163
159
152

211
207
200
193
189
181

236
230
223
215
210
202

275
268
258
249
243
233

300
293
282
272
265
254

302
300
293
285
280
270

355
355
350
342
337
326

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
164
163
160
156
153
148

0QVGU

355
355
350
342
337
326

374
380
380
375
371
362

470
470
464
454
447
433

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9136
Ratio
r/min
Fans

Without Fan With Fan

470
1800 Quadruple
1.00
20
1.00
470
1500 Reduction
Horizontal
0.85
30
0.87
464
1200
Type
0.70
40
0.73
454
1000
100
447
900
0.55

50
0.60
433
750
125
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
100

900
125
750

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
100
900

750
125

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 33

SELECTION Right Angle Shaft Quadruple Reduction

Nominal Reduction Ratio 140 180

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
13
1500
11
140
1200
8.6
1000
7.1
900
6.4
750
5.4
Exact Reduction Ratio
1800
11
1500
9.4
160
1200
7.5
1000
6.3
900
5.6
750
4.7
Exact Reduction Ratio
1800
10
1500
8.3
180
1200
6.7
1000
5.6
900
5.0
750
4.2
Horizontal
Dimension
Vertical
Tables
Upright

140.03 143.57 148.10 145.56 149.12 147.31 143.38 135.67 139.40 129.07 141.18

13.4
11.2
8.9
7.5
6.7
5.6

17.3
14.5
11.6
9.7
8.7
7.3

19.6
16.4
13.1
10.9
9.9
8.2

25.6
21.4
17.1
14.3
12.9
10.7

30
25.6
20.5
17.1
15.4
12.9

39
33
26.6
22.2
20.0
16.7

50
41
33
28.0
25.2
21.0

69
58
46
38
35
29.2

78
65
52
43
39
32

107
89
71
59
54
45

113
95
76
63
57
47

156.02 158.68 162.11 156.75 160.47 152.99 158.44 158.25 154.04 163.15

16.5
13.8
11.0
9.2
8.3
6.9

17.1
14.3
11.4
9.5
8.6
7.1

25.5
21.3
17.1
14.2
12.8
10.7

25.7
21.4
17.1
14.3
12.8
10.7

63
53
42
35
31
26.6

40
34
27.2
22.7
20.4
17.0

68
57
46
38
34
28.7

95
79
64
53
48
40

102
85
68
57
51
43

177.50 180.65 182.13 182.66 183.53 171.41 177.79 174.54 169.14 177.48

90
82
62
53
39
32
14.0 16.1 20.5 25.1
75
68
52
44
33
11.7 13.4 17.1 20.9 26.7
60
54
42
35
9.4 10.8 13.7 16.8 21.4 26.6
50
45
35
9.0 11.4 14.0 17.8 22.1 29.7
7.8
45
41
31
8.1 10.3 12.6 16.1 19.9 26.7
7.1
38
34
8.6 10.5 13.4 16.6 22.3 26.4
6.7
5.9
C-62 C-62 C-62 C-62 C-64 C-64 C-64 C-64 C-64 C-64 C-66
C-82 C-82 C-82 C-82 C-84 C-84 C-84 C-84 C-84 C-84 C-86
C-96 C-96 C-96 C-96 C-98 C-98 C-98 C-98 C-98 C-98

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple 1800
38
42
40
55
59
75
81
102
101
130 144
Reduction
37
41
38
53
56
73
78
100
98
127 140
1500
Horizontal
35
39
36
51
53
70
73
97
93
123 135
1200
Type
34
38
34
48
50
67
70
93
89
119 129
1000
140
33
37
32
47
48
65
67
91
86
117 126
900

31
35
30
45
45
62
63
86
81
111 120
750
180
Quadruple
Reduction
Vertical
Type

140

180
Quadruple
Reduction
Upright
Type

140

180

C - 34

1800
1500
1200
1000
900
750

40
39
37
35
34
32

45
43
41
39
38
36

42
39
37
34
33
30

58
55
52
50
48
45

61
58
54
51
49
46

79
76
72
68
66
63

84
81
75
71
69
64

109
105
100
96
93
88

107
102
96
91
88
82

139
135
129
123
120
114

1800
1500
1200
1000
900
750

39
38
37
35
34
33

42
41
39
38
37
35

40
38
36
33
32
30

54
53
51
48
47
44

59
56
53
50
48
45

75
73
70
67
65
62

81
78
73
70
67
63

102
100
96
93
91
86

101
98
93
89
86
81

129
127
123
119
116
111

152
147
139
133
129
122

SELECTION Right Angle Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 140 180

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

13
1800
11
1500
140
8.6
1200
7.1
1000
6.4
900
5.4
750
157.57 155.60 155.60 Exact Reduction Ratio
502 574 678
11
1800
419 480 566
9.4
1500
336 385 454
160
7.5
1200
281 321 379
6.3
1000
253 289 341
5.6
900
211 241 285
4.7
750
179.00 171.03 171.03 Exact Reduction Ratio
443 523 617
10
1800
370 437 515
8.3
1500
296 350 413
180
6.7
1200
247 292 345
5.6
1000
223 263 311
5.0
900
186 220 259
4.2
750
C-70 C-70 C-70 Horizontal
Dimension
Vertical
Tables
Upright

144.00 133.22 135.88 136.77 135.09 146.39 142.31 142.31 145.23 136.02 136.02

137
114
91
76
69
57

170
141
113
95
85
71

206
172
138
115
104
86

236
197
158
132
119
99

303
253
203
169
152
127

337
281
226
188
170
142

399
333
267
223
201
168

464
388
311
260
234
195

156.24 158.28 147.43 153.67 154.53 150.98 154.40 154.40

121
101
81
67
61
50

150
125
100
84
75
63

183
153
123
102
92
77

222
186
149
124
112
93

250
208
167
139
126
105

327
273
219
183
165
137

368
307
246
206
185
155

429
358
287
240
216
180

181.03 169.85 173.25 181.61 174.16 178.43 177.88 177.88

109 133 162 189 236 277 320 373

91 111 135 157 197 231 267 311
89 108 126 158 185 214 249
73
90 105 131 155 179 208
74
61
95 118 139 161 187
81
67
55
99 116 134 156
79
68
56
45
C-66 C-66 C-66 C-66 C-66 C-68 C-68 C-68
C-86 C-86 C-86 C-86 C-86

544
454
364
304
274
229

656
548
439
367
330
276

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131
188
184
178
171
167
160

205
201
194
186
182
174

242
237
228
219
213
204

265
258
248
238
232
221

164
158
150
143
138
131

200
194
184
176
172
163

218
211
200
192
186
177

256
247
235
224
218
207

279
269
255
244
237
225

291
288
281
273
268
258

339
334
325
316
309
298

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
155
151
145
139
135
129

774
646
518
433
390
325

0QVGU

339
334
325
316
309
298

372
369
361
352
346
334

457
456
444
431
422
406

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9136
Ratio
r/min
Fans

Without Fan With Fan

457
1800 Quadruple
1.00
20
1.00
456
1500 Reduction
Horizontal
0.85
30
0.87
444
1200
Type
0.70
40
0.73
431
1000
140
422

900
0.55
50
0.60
406
180
750
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
140
900

750
180

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
140

900
180
750

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 35

SELECTION Right Angle Shaft Quadruple Reduction

Nominal Reduction Ratio 200 250

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
9.0
1500
7.5
200
1200
6.0
1000
5.0
900
4.5
750
3.8
Exact Reduction Ratio
1800
8.0
1500
6.7
224
1200
5.4
1000
4.5
900
4.0
750
3.3
Exact Reduction Ratio
1800
7.2
1500
6.0
250
1200
4.8
1000
4.0
900
3.6
750
3.0
Horizontal
Dimension
Vertical
Tables
Upright

207.95 197.74 205.42 196.56 191.23

15.0
12.5
10.0
8.4
7.5
6.3

17.1
14.3
11.4
9.5
8.6
7.1

24.3
20.3
16.3
13.6
12.2
10.2

25.7
21.4
17.1
14.3
12.8
10.7

192.89 192.86 207.64

59
49
39
33
30
25.0

39
33
26.6
22.1
19.9
16.6

68
57
46
38
34
28.7

80
67
53
45
40
33

236.74 222.15 239.37 224.81 214.26 212.55 212.75 211.77 225.88

12.3
10.3
8.2
6.9
6.2
5.2

16.8
14.0
11.3
9.4
8.5
7.1

19.2
16.0
12.8
10.7
9.6
8.0

25.7
21.4
17.1
14.3
12.9
10.7

33
28.1
22.5
18.8
16.9
14.1

39
33
26.6
22.1
19.9
16.6

51
43
34
28.8
25.9
21.6

65
54
44
36
33
27.6

71
59
47
39
35
30

260.18 259.14 255.94 257.59 250.61 236.76 252.78 235.08 259.56

64
62
45
39
30
12.0 16.0 19.6 25.5
53
52
38
33
10.0 13.4 16.3 21.2 25.8
43
42
30
8.0 10.7 13.1 17.0 20.6 26.6
36
35
8.9 10.9 14.1 17.2 22.2 25.5
6.7
32
31
9.8 12.7 15.5 19.9 22.9
8.0
6.0
8.2 10.6 12.9 16.6 19.1 26.4 27.1
6.7
5.0
C-62 C-62 C-64 C-64 C-64 C-64 C-64 C-64 C-66
C-82 C-82 C-84 C-84 C-84 C-84 C-84 C-84 C-86
C-96 C-96 C-98 C-98 C-98 C-98 C-98 C-98

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple 1800
37
45
54
65
74
91
94
114 128
Reduction
35
43
52
62
71
87
91
110 124
1500
Horizontal
33
40
48
58
67
82
86
104 118
1200
Type
31
38
46
55
64
78
82
99 112
1000
200
30
36
44
53
62
75
79
96 109
900

28
34
41
49
58
71
75
90 103
750
250
Quadruple
Reduction
Vertical
Type
200

250
Quadruple
Reduction
Upright
Type

200

250

C - 36

1800
1500
1200
1000
900
750

38
36
34
31
30
28

47
44
41
38
37
34

56
53
50
47
45
42

67
63
59
55
53
50

77
74
69
65
63
59

94
90
84
79
76
72

98
94
88
84
81
76

119
114
107
101
98
92

1800
1500
1200
1000
900
750

37
35
33
31
30
28

45
43
40
38
36
34

54
52
48
46
44
41

65
62
58
55
53
49

74
71
67
64
62
58

91
87
82
78
75
71

94
91
86
82
79
75

114
110
104
99
96
90

134
129
121
115
111
105

SELECTION Right Angle Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 200 250

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

9.0
1800
7.5
1500
200
6.0
1200
5.0
1000
4.5
900
3.8
750
229.95 215.37 215.37 Exact Reduction Ratio
345 417 491 8.0
1800
288 348 410
6.7
1500
231 279 329
224
5.4
1200
193 233 274
4.5
1000
174 209 247
4.0
900
145 175 206
3.3
750
249.49 246.37 246.37 Exact Reduction Ratio
319 365 430 7.2
1800
266 304 359
6.0
1500
213 244 288
250
4.8
1200
178 203 240
4.0
1000
160 183 216
3.6
900
134 153 180
3.0
750
C-70 C-70 C-70 Horizontal
Dimension
Vertical
Tables
Upright

196.41 203.69 187.97 195.58 205.82 190.95 193.00 193.00 194.21 195.65 195.65

96
80
64
53
48
40

117
97
78
65
58
49

144
120
96
80
72
60

172
143
115
96
86
72

200
167
133
111
100
84

259
216
173
145
130
109

295
246
198
165
148
124

344
287
230
192
173
144

230.40 218.59 222.96 224.42 221.65 230.04 226.29 226.29

86
71
57
48
43
36

104
86
69
58
52
43

126
105
84
70
63
53

145
121
97
81
73
60

172
143
115
96
86
72

215
180
144
120
108
90

252
211
169
141
127
106

294
245
196
164
148
123

249.98 248.28 241.90 238.39 253.56 237.26 245.51 245.51

96 112 144 153 209 233 271

76
94 120 127 174 194 226
80
63
96 102 140 156 181
75
64
50
85 117 130 151
80
62
53
42
77 105 117 136
72
56
48
38
97 113
87
64
60
47
40
31
C-66 C-66 C-66 C-66 C-66 C-68 C-68 C-68
C-86 C-86 C-86 C-86 C-86

408
341
273
228
205
171

458
382
307
256
230
192

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131
167
162
155
149
145
137

186
180
173
165
161
152

217
210
200
191
186
176

237
229
218
208
203
192

149
143
134
128
123
116

176
169
160
153
148
140

196
188
178
169
164
155

226
217
205
195
189
179

247
237
224
213
206
195

273
265
254
244
238
226

325
317
306
294
287
275

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
142
137
131
125
121
114

540
451
362
302
272
227

0QVGU

325
317
306
294
287
275

352
344
331
318
310
296

426
417
402
388
379
362

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9136
Ratio
r/min
Fans

Without Fan With Fan

426
1800 Quadruple
1.00
20
1.00
417
1500 Reduction
Horizontal
0.85
30
0.87
402
1200
Type
0.70
40
0.73
388
1000
200
379
900
0.55

50
0.60
362
750
250
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
200
900

750
250

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
200
900

750
250

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 37

SELECTION Right Angle Shaft Quadruple Reduction

Nominal Reduction Ratio 280 355

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
6.4
1500
5.4
280
1200
4.3
1000
3.6
900
3.2
750
2.7
Exact Reduction Ratio
1800
5.7
1500
4.8
1200
3.8
315
1000
3.2
900
2.9
750
2.4
Exact Reduction Ratio
1800
5.1
1500
4.2
355
1200
3.4
1000
2.8
900
2.5
750
2.1
Horizontal
Dimension
Vertical
Tables
Upright

296.20 291.13 298.24 294.61 280.79 265.69 278.80 258.13 282.35

9.9
8.2
6.6
5.5
4.9
4.1

12.9
10.7
8.6
7.2
6.5
5.4

15.4
12.9
10.3
8.6
7.7
6.4

20.0
16.7
13.4
11.1
10.0
8.4

25.7
21.5
17.2
14.4
12.9
10.8

35
29.8
23.9
19.9
17.9
15.0

39
32
26.4
22.0
19.8
16.5

54
45
36
30
27.1
22.6

57
47
38
31
28.8
24.0

315.95 324.22 332.51 320.94 322.08 310.27 318.63 308.07 308.36

9.2
7.7
6.2
5.2
4.6
3.9

12.8
10.7
8.6
7.1
6.4
5.4

13.8
11.5
9.2
7.7
6.9
5.8

20.4
17.0
13.6
11.4
10.2
8.5

22.5
18.7
15.0
12.5
11.3
9.4

32
27.2
21.8
18.2
16.4
13.6

34
28.9
23.1
19.3
17.4
14.5

48
40
32
26.8
24.2
20.2

52
43
35
29.3
26.3
22.0

367.08 364.25 369.46 367.06 343.56 348.18 355.25 338.28 353.71

45
41
31
8.0 10.3 12.5 16.1 21.1 27.3
38
34
8.6 10.4 13.4 17.6 22.8 25.9
6.6
30
8.3 10.7 14.1 18.3 20.7 27.6
6.9
5.3
9.0 11.7 15.2 17.3 23.0 25.5
6.9
5.7
4.4
8.1 10.6 13.7 15.6 20.7 23.0
6.2
5.2
4.0
8.8 11.4 13.0 17.3 19.2
6.7
5.2
4.3
3.3
C-62 C-62 C-64 C-64 C-64 C-64 C-64 C-64 C-66
C-82 C-82 C-84 C-84 C-84 C-84 C-84 C-84 C-86
C-96 C-96 C-98 C-98 C-98 C-98 C-98 C-98

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple 1800
37
43
54
62
75
87
94
109 127
Reduction
35
41
52
59
72
83
91
105 123
1500
Horizontal
33
39
49
56
68
78
86
100 117
1200
Type
31
36
46
52
64
74
82
94 112
1000
280
30
35
44
50
62
72
80
91 109
900

28
32
42
47
58
67
75
86 103
750
355
Quadruple
Reduction
Vertical
Type

280

355
Quadruple
Reduction
Upright
Type

280

355

C - 38

1800
1500
1200
1000
900
750

38
36
34
31
30
28

45
42
39
37
35
33

56
54
50
47
45
42

64
61
57
53
51
48

78
74
70
66
63
59

90
85
80
75
73
68

99
95
89
84
81
76

114
109
102
96
93
87

1800
1500
1200
1000
900
750

37
35
33
31
30
28

43
41
39
36
35
32

54
52
49
46
44
42

62
59
56
52
50
47

75
72
68
64
62
58

87
83
78
74
71
67

94
91
86
82
80
75

109
105
99
94
91
86

133
128
121
114
111
104

SELECTION Right Angle Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 280 355

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

6.4
1800
5.4
1500
280
4.3
1200
3.6
1000
3.2
900
2.7
750
Exact Reduction Ratio
5.7
1800
4.8
1500
315
3.8
1200
3.2
1000
2.9
900
2.4
750
Exact Reduction Ratio
5.1
1800
4.2
1500
355
3.4
1200
2.8
1000
2.5
900
2.1
750
C-70 C-70 Horizontal
Dimension
Vertical
Tables
Upright

288.00 266.44 271.77 273.54 270.18 280.39 288.00 288.00 283.41 291.16 291.16

69
57
46
38
34
28.9

85
71
57
47
43
35

104
86
69
58
52
43

119
99
79
66
60
50

152
127
102
85
76
64

177
148
118
99
89
74

199
166
133
111
100
83

231
193
155
129
116
97

281
234
188
157
141
118

312.47 301.20 294.86 323.28 309.07 320.45 312.47 312.47 307.49

61
50
40
34
30
25.5

75
63
50
42
38
31

92
77
61
51
46
38

101
84
67
56
50
42

126
105
84
70
63
52

155
129
104
86
78
65

183
153
122
102
92
77

213
178
142
119
107
89

259
216
173
144
130
108

341.25 344.23 333.33 369.46 365.26 356.86 341.25 341.25 347.61

88 106 139 168 195 229

81
66
55
89 116 140 163 191
73
68
55
46
93 112 131 153
71
59
54
44
37
93 109 128
78
59
49
45
37
31
98 115
84
70
53
44
41
33
28.1
96
82
70
58
44
37
34
23.4 27.8
C-66 C-66 C-66 C-66 C-66 C-68 C-68 C-68 C-70
C-86 C-86 C-86 C-86 C-86

309
258
207
172
155
129

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131
167
162
155
149
145
138

180
175
167
160
155
147

208
202
192
184
179
169

228
220
210
200
195
184

143
137
129
123
119
112

176
169
160
153
148
140

189
182
172
164
159
150

217
208
197
188
182
172

237
227
215
204
198
187

248
240
228
218
212
200

304
295
282
270
263
250

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
137
132
126
120
116
110

365
304
244
203
183
153

0QVGU

304
295
282
270
263
250

340
332
319
306
299
285

421
412
397
383
374
358

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9136
Ratio
r/min
Fans

Without Fan With Fan

421
1800 Quadruple
1.00
20
1.00
412
1500 Reduction
Horizontal
0.85
30
0.87
397
1200
Type
0.70
40
0.73
383
1000
280
374
900
0.55

50
0.60
358
750
355
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
280
900

750
355

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
280
900

750
355

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 39

SELECTION Right Angle Shaft Quadruple Reduction

Nominal Reduction Ratio 400 450

MECHANICAL POWER RATING (kW)

Nominal H.Speed
L.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
r/min

Exact Reduction Ratio

1800
4.5
1500
3.8
400
1200
3.0
1000
2.5
900
2.3
750
1.9
Exact Reduction Ratio
1800
4.0
1500
3.3
450
1200
2.7
1000
2.2
900
2.0
750
1.7
Horizontal
Dimension
Vertical
Tables
Upright

388.53

409.25

399.38

386.60

9.7
8.1
6.5
5.4
4.8
4.0

14.4
12.0
9.6
8.0
7.2
6.0

23.8
19.9
15.9
13.3
12.0
10.0

36
30
24.2
20.2
18.2
15.1

451.41

454.72

426.01

431.03

8.3
6.9
5.6
4.6
4.2
3.5
C-62
C-82
C-96

13.0
10.8
8.7
7.2
6.5
5.4
C-64
C-84
C-98

22.4
18.6
14.9
12.5
11.2
9.4
C-64
C-84
C-98

32
27.1
21.7
18.1
16.3
13.6
C-64
C-84
C-98

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple 1800
45
64
86
110
Reduction
43
61
83
106
1500
Horizontal
40
58
78
100
1200
Type
37
54
74
95
1000
400
36
52
71
92
900

33
49
67
87
750
450
Quadruple
Reduction
Vertical
Type

400

450
Quadruple
Reduction
Upright
Type

400

450

C - 40

1800
1500
1200
1000
900
750

46
44
41
38
36
34

66
63
59
55
53
49

89
85
80
75
72
68

114
109
103
97
94
88

1800
1500
1200
1000
900
750

45
43
40
37
36
33

64
61
58
54
52
49

86
83
78
74
71
67

110
106
100
95
92
87

SELECTION Right Angle Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
391.44

380.94

48
40
32
27.2
24.5
20.4

71
59
48
40
36
30

C-66
C-86

C-66
C-86

417.44 407.84

93
78
62
52
47
39

122
102
81
68
61
51

C-66 C-68
C-86

Nominal Reduction Ratio 400 450

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

4.5
1800
3.8
1500
400
3.0
1200
2.5
1000
2.3
900
1.9
750
Exact Reduction Ratio
4.0
1800
3.3
1500
450
2.7
1200
2.2
1000
2.0
900
1.7
750
Horizontal
Dimension
Vertical
Tables
Upright

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9118 9121 9126 9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

246
1800 Quadruple
1.00
20
1.00
238
1500 Reduction
Horizontal
0.85
30
0.87
226
1200
Type
0.70
40
0.73
216
1000
400
210
900
0.55

50
0.60
198
750
450

Size of Reducer
9095 9100 9105 9110 9115
137
133
127
121
117
111

179
174
166
159
155
147

225
218
208
198
193
183

144
138
130
123
119
113

188
181
171
163
158
149

234
225
213
202
196
185

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
400
900

750
450

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
400
900

750
450

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 41

SELECTION Allowable Radial and Axial Loads on Slow Speed

Right Angle shaft

Allowable Radial Load (kN)

Sheet 1
L.Speed
Shaft
Speed
r/min 9015
250 11.8
160 11.8
Standard 100 11.8
bearing
63 11.8
model
40 11.8
25 11.8
250
160
Heavy
duty 100
bearing 63
model
40
25

Size of Reducer
9025
17.7
17.7
17.7
17.7
17.7
17.7

9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080
17.7 29.4 29.9 32.4 37.8 46.6 39.7 49.1 44.1 77.0 77.0
20.1 31.4 32.4 33.8 39.7 48.1 41.7 50.5 46.1 89.0 89.0
25.0 35.3 38.7 39.2 47.1 53.5 47.6 54.4 54.4 99.0 99.0
26.5 35.3 42.2 47.1 54.9 62.3 58.9 64.3 65.2 131.5 131.5
26.5 35.3 42.2 49.1 54.9 67.7 71.1 78.0 79.0 141.0 141.0
26.5 35.3 42.2 49.1 54.9 67.7 81.4 95.2 99.1 139.5 139.5
71.1 93.7 70.1 122.5 122.5
78.0 94.7 77.5 137.5 137.5
81.4 98.1 92.2 149.5 149.5
81.4 98.1 114.8 149.0 149.0
81.4 98.1 117.7 148.5 148.5
81.4 98.1 117.7 147.0 147.0

Sheet 2

Dimension Selection
Tables
Tables

Speed
Reducer

Applicable to congurations: Double Reduction RR, LL/

9085
100.1
108.9
122.1
125.6
125.1
122.6
141.8
132.4
127.0
125.6
125.1
122.6

9090
100.1
108.9
122.1
125.6
125.1
122.6
141.8
132.4
127.0
125.6
125.1
122.6

9095
137.8
145.7
147.6
143.7
137.8
135.4
158.9
151.6
147.6
143.7
137.8
135.4

9100
139.8
157.5
166.3
165.3
164.8
163.3
181.0
174.6
166.8
165.8
165.3
163.8

Applicable to congurations: Double Reduction RL, LR/

L.Speed
Size of Reducer
Shaft
Speed
r/min 9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090 9095 9100
250
8.3
15.2
9.8
21.6 19.1 21.6 22.6 31.4 16.7 28.4 17.2 44.0 44.0 58.4 58.4 97.6 80.4
160
9.8
17.7 12.3 23.1 20.6 23.1 24.0 31.4 18.1 27.0 17.7 55.5 55.5 64.3 64.3 103.0 96.1
Standard 100 11.8 17.7 16.7 29.4 26.0 27.5 28.4 35.3 22.1 30.4 25.5 63.5 63.5 74.6 74.6 110.9 105.9
bearing
63 11.8 17.7 21.6 35.3 32.9 35.3 37.3 42.7 33.4 38.3 33.8 95.0 95.0 104.5 104.5 148.1 153.5
model
40 11.8 17.7 26.5 35.3 41.7 43.7 48.6 55.4 45.1 51.5 47.6 129.0 129.0 146.7 146.7 172.2 203.6
25 11.8 17.7 26.5 35.3 42.2 49.1 54.9 67.7 60.8 68.7 67.7 167.0 167.0 171.2 171.2 171.2 215.3
250
46.1 74.6 40.2 90.0 90.0 114.8 114.8 156.0 150.6
160
52.0 72.1 45.6 103.5 103.5 125.1 125.1 164.8 170.7
Heavy
100
60.3 79.0 59.4 116.0 116.0 140.8 140.8 176.1 187.4
duty
bearing 63
81.4 96.6 80.0 152.5 152.5 174.1 174.1 186.9 218.8
model
40
81.4 98.1 108.9 192.0 192.0 191.8 191.8 193.7 241.8
81.4 98.1 117.7 180.5 180.5 171.2 171.2 171.2 214.8
25

Allowable Axial Load (kN)

L.Speed
Size of Reducer
Shaft
Speed
r/min 9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090 9095 9100
250
9.3
11.4 14.7 23.1 26.5 31.4 32.9 31.9 27.0 43.2 28.0 28.0 23.5 23.5 31.4 52.0 45.1
160
9.3
11.4 18.1 23.1 28.4 31.4 33.4 31.9 28.9 43.2 28.4 28.4 27.5 27.5 34.3 53.0 53.0
9.3
11.4 24.5 23.1 32.9 31.4 37.3 31.9 34.3 43.2 39.7 39.7 32.9 32.9 43.2 59.4 58.4
Standard 100
bearing
63
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 52.5 52.5 45.6 45.6 54.0 59.8 81.4
model
40
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 61.4 61.4 63.3 60.3 59.8 59.8 83.4
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 61.4 61.4 67.7 60.3 59.8 59.8 83.4
25
250
23.1 34.8 18.6 18.6 56.9 56.9 59.8 59.8 83.4
160
25.0 33.4 21.1 21.1 56.9 56.9 59.8 59.8 83.4
Heavy
100
29.4 36.8 27.5 27.5 56.9 56.9 59.8 59.8 83.4
duty
bearing
63
39.2 43.2 36.3 36.3 56.9 56.9 59.8 59.8 83.4
model
40
39.2 43.2 49.1 49.1 56.9 56.9 59.8 59.8 83.4
39.2 43.2 56.9 56.9 56.9 56.9 59.8 59.8 83.4
25

C - 42

SELECTION Allowable Radial and Axial Loads on Slow Speed

Triple Reduction RL, LR/Quadruple Reduction RR, LL

Overhang Factor

Size of Reducer
9105
192.3
200.6
183.9
178.1
173.6
167.3
213.9
200.6
183.9
178.1
173.6
167.3

9110
167.8
174.1
184.9
190.8
194.7
184.9
250.6
214.8
195.2
190.8
194.7
184.9

9115
222.7
234.9
245.7
303.1
320.8
316.4
316.9
334.5
340.9
333.5
320.8
316.4

9118

9121 9126 9128 9131 9136

391.9
387.5
460.1
448.3

352.7
369.3
449.3
554.8

330.6
341.4
401.2
497.4

315.4
328.6
409.6
534.6

403.2
462.5
572.4
733.8

391.9
430.7
511.1
638.6

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
bearing
63 model
40
25
250
160 Heavy
100 duty
63 bearing
model
40
25

Unit: kN
Triple Reduction RR, LL/Quadruple Reduction RL, LR
Size of Reducer
9105
131.5
138.3
146.7
200.1
235.4
304.1
213.4
223.2
236.9
301.7
304.1
304.1

9110
94.2
92.2
101.0
144.7
199.1
272.7
191.3
197.7
210.4
267.8
323.7
323.7

9115
152.5
155.0
167.3
220.7
250.2
353.2
248.7
261.4
274.2
341.9
382.1
374.7

9118

9121 9126 9128 9131 9136

312.0
292.3
373.3
460.1

228.1
244.3
322.7
427.2

197.7
206.0
257.0
348.7

159.4
170.7
250.2
373.3

Right Angle shaft

203.6
260.9
369.3
528.3

190.3
218.8
286.5
398.3

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
bearing
63 model
40
25
250
160
Heavy
100 duty
63 bearing
model
40
25

Overhang Member
Sprocket (Single Row)
Sprocket (Double Row)
Gears

Overhang Factor
1
1.25
1.25

Notes
1. The value shown in the table is allowable radial
load when it is applied to the center of the solid
shaft (except hollow shaft).
Consult us when a load is not in the center.
2. Consult us for the blanks in the table.
3. Consult us when the radial load is applied
upward.
4. In case of double projection shaft (RB,LB)
(1) See sheet1 when the radial load is applied
only to the shaft1.
(2) See sheet2 when the radial load is applied
only to the shaft2.
(3) Consult us when the radial load is applied to
both shafts.
5. Refer to C-6 to check overhang load, and
calculate equivalent load at peak load value.
Be careful under following condition because
large peak load may be generated.
Application: When the inertia is large, such as
for crane driving, slewing, etc.
Motor: inline motor
Connecting method: Sprocket or gear
Consult us when the peak load is larger than
allowable value.

Unit: kN

RB
Size of Reducer
9105 9110
50.0 50.0
49.5 49.5
54.0 54.0
74.6 74.6
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4

9115
76.5
76.5
83.4
83.4
83.4
83.4
83.4
83.4
83.4
83.4
83.4
83.4

9118

119.7
119.7
119.7
119.7

9121 9126 9128 9131 9136

121.6
121.6
121.6
121.6

116.7
121.6
121.6
121.6

91.2
96.6
134.9
144.2

113.3
140.3
191.3
192.3

107.9
122.6
155.5
192.3

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
bearing
63 model
40
25
250
160
100 Heavy
duty
63 bearing
model
40
25

LB
2

1
Double
Reduction
Ratio


2

Triple
Reduction
Ratio

2
2

1
Quadruple
Reduction
Ratio

Unit: kN

C - 43

SELECTION Allowable Radial and Axial Loads on Slow Speed

Right Angle shaft

Allowable Radial Load (kgf)

Sheet 1
L.Speed
Shaft
Speed
r/min
250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
duty 100
bearing 63
model
40
25

Applicable to congurations: Double Reduction RR, LL/

Size of Reducer
9015
1200
1200
1200
1200
1200
1200

9025
1800
1800
1800
1800
1800
1800

9030
1800
2050
2550
2700
2700
2700

9035
3000
3200
3600
3600
3600
3600

9040
3050
3300
3950
4300
4300
4300

9045
3300
3450
4000
4800
5000
5000

9050
3850
4050
4800
5600
5600
5600

9055
4750
4900
5450
6350
6900
6900

9060
4050
4250
4850
6000
7250
8300
7250
7950
8300
8300
8300
8300

9065
5000
5150
5550
6550
7950
9700
9550
9650
10000
10000
10000
10000

Sheet 2

Dimension Selection
Tables
Tables

Speed
Reducer

L.Speed
Shaft
Speed
r/min
250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
duty 100
bearing 63
model
40
25

9070
4500
4700
5550
6650
8050
10100
7150
7900
9400
11700
12000
12000

9075
7850
9050
10100
13400
14350
14200
12500
14000
15250
15200
15150
15000

9080
7850
9050
10100
13400
14350
14200
12500
14000
15250
15200
15150
15000

9085
10200
11100
12450
12800
12750
12500
14450
13500
12950
12800
12750
12500

9090
10200
11100
12450
12800
12750
12500
14450
13500
12950
12800
12750
12500

9095
14050
14850
15050
14650
14050
13800
16200
15450
15050
14650
14050
13800

9100
14250
16050
16950
16850
16800
16650
18450
17800
17000
16900
16850
16700

Applicable to congurations: Double Reduction RL, LR/

Size of Reducer
9015
850
1000
1200
1200
1200
1200

9025
1550
1800
1800
1800
1800
1800

9030
1000
1250
1700
2200
2700
2700

9035
2200
2350
3000
3600
3600
3600

9040
1950
2100
2650
3350
4250
4300

9045
2200
2350
2800
3600
4450
5000

9050
2300
2450
2900
3800
4950
5600

9055
3200
3200
3600
4350
5650
6900

9060
1700
1850
2250
3400
4600
6200
4700
5300
6150
8300
8300
8300

9065
2900
2750
3100
3900
5250
7000
7600
7350
8050
9850
10000
10000

9070
1750
1800
2600
3450
4850
6900
4100
4650
6050
8150
11100
12000

9075
4500
5650
6450
9700
13150
17000
9150
10550
11800
15550
19550
18400

9080
4500
5650
6450
9700
13150
17000
9150
10550
11800
15550
19550
18400

9085
5950
6550
7600
10650
14950
17450
11700
12750
14350
17750
19550
17450

9090
5950
6550
7600
10650
14950
17450
11700
12750
14350
17750
19550
17450

9095
9950
10500
11300
15100
17550
17450
15900
16800
17950
19050
19750
17450

9100
8200
9800
10800
15650
20750
21950
15350
17400
19100
22300
24650
21900

9070
2850
2900
4050
5350
6260
6260
1900
2150
2800
3700
5000
5800

9075
2850
2900
4050
5350
6260
6260
1900
2150
2800
3700
5000
5800

9080
2400
2800
3350
4650
6450
6900
5800
5800
5800
5800
5800
5800

9085
2400
2800
3350
4650
6150
6150
5800
5800
5800
5800
5800
5800

9090
3200
3500
4400
5500
6100
6100
6100
6100
6100
6100
6100
6100

9095
5300
5400
6050
6100
6100
6100
6100
6100
6100
6100
6100
6100

9100
4600
5400
5950
8300
8500
8500
8500
8500
8500
8500
8500
8500

Allowable Axial Load (kgf)

L.Speed
Shaft
Speed
r/min 9015 9025
250 950 1160
160 950 1160
950 1160
Standard 100
bearing
63
950 1160
model
40 950 1160
25 950 1160
250
160
Heavy
100
duty
bearing
63
model
40
25

C - 44

Size of Reducer
9030
1500
1850
2500
2700
2700
2700

9035
2350
2350
2350
2350
2350
2350

9040
2700
2900
3350
3350
3350
3350

9045
3200
3200
3200
3200
3200
3200

9050
3350
3400
3800
3800
3800
3800

9055
3250
3250
3250
3250
3250
3250

9060
2750
2950
3500
5000
5000
5000
2350
2550
3000
4000
4000
4000

9065
4400
4400
4400
4400
4400
4400
3550
3400
3750
4400
4400
4400

SELECTION Allowable Radial and Axial Loads on Slow Speed

Triple Reduction RL, LR/Quadruple Reduction RR ,LL

Overhang Factor

Size of Reducer
9105
19600
20450
18750
18150
17700
17050
21800
20450
18750
18150
17700
17050

9110
17100
17750
18850
19450
19850
18850
25550
21900
19900
19450
19850
18850

9115
22700
23950
25050
30900
32700
32250
32300
34100
34750
34000
32700
32250

9118

39950
39500
46900
45700

9121 9126 9128 9131 9136

35950
37650
45800
56550

33700
34800
40900
50700

32150
33500
41750
54500

41100
47150
58350
74800

39950
43900
52100
65100

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
bearing
63 model
40
25
250
160 Heavy
duty
100
63 bearing
model
40
25

Unit: kgf
Triple Reduction RR, LL/Quadruple ReductionRL ,LR
Size of Reducer
9105
13400
14100
14950
20400
24000
31000
21750
22750
24150
30750
31000
31000

9110
9600
9400
10300
14750
20300
27800
19500
20150
21450
27300
33000
33000

9115
15550
15800
17050
22500
25500
36000
25350
26650
27950
34850
38950
38200

9118

31800
29800
38050
46900

9121 9126 9128 9131 9136

23250
24900
32900
43550

20150
21000
26200
35550

16250
17400
25500
38050

Right Angle shaft

20750
26600
37650
53850

19400
22300
29200
40600

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
bearing
63 model
40
25
250
160
Heavy
100
duty
63 bearing
model
40
25

Overhang Member
Sprocket (Single Row)
Sprocket (Double Row)
Gears

Overhang Factor
1
1.25
1.25

Notes
1. The value shown in the table is allowable radial
load when it is applied to the center of the solid
shaft (except hollow shaft).
Consult us when a load is not in the center.
2. Consult us for the blanks in the table.
3. Consult us when the radial load is applied
upward.
4. In case of double projection shaft (RB,LB)
(1) See sheet1 when the radial load is applied
only to the shaft1.
(2) See sheet2 when the radial load is applied
only to the shaft2.
(3) Consult us when the radial load is applied to
both shafts.
5. Refer to C-6 to check overhang load, and
calculate equivalent load at peak load value.
Be careful under following condition because
large peak load may be generated.
Application: When the inertia is large, such as
for crane driving, slewing, etc.
Motor: inline motor
Connecting method: Sprocket or gear
Consult us when the peak load is larger than
allowable value.

Unit: kgf

RB
Size of Reducer
9105

9110

9115

5100
5050
5500
7600
8500
8500
8500
8500
8500
8500
8500
8500

5100
5050
5500
7600
8500
8500
8500
8500
8500
8500
8500
8500

7800
7800
8500
8500
8500
8500
8500
8500
8500
8500
8500
8500

9118

12200
12200
12200
12200

9121

12400
12400
12400
12400

9126

11900
12400
12400
12400

9128

9300
9850
13750
14700

9131

11550
14300
19500
19600

9136

11000
12500
15850
19600

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
bearing
63 model
40
25
250
160
100 Heavy
duty
63 bearing
model
40
25

LB
2

1
Double
Reduction
Ratio

1
2

Triple
Reduction
Ratio

1
Quadruple
Reduction
Ratio

Unit: kgf

C - 45

DIMENSIONS Right Angle Shaft Double Reduction Horizontal Mounting

A

FC

R
L2

FA

FB

X2

Z2

FD

FA

Y2

9015 9055

W2

High Speed Shaft

With Fan
Refer to the page D-20 for details.
*

DP1

DP1

FY

4- J
K

K
DP2

Dimension Selection
Tables
Tables

Speed
Reducer

D
G

Y
L

F
E1

E2

H
L

[Fig. 1] Location of oil ll and air vent for

Size 9015 9030 with reduction ratio 6.3
or 7.1

O
P

* Location of oil ll and air vent changes for Size

9015 9030 with reduction ratio 6.3 or 7.1.
Refer to Fig. 1.
Size

E1

E2

FY

9015
9025
9030
9035
9040
9045
9050
9055

507
545
645
676
705
744
755
794

160
175
200
219
235
256
255
286

427
465
535
566
595
634
645
684

90
95
110
129
120
141
138.5
171

135
155
160
185
200
220
210
245

270
310
320
370
400
440
420
490

309
346
353

299
339
349
399
431
471
451
521

129
142
154
154
172
172
192
192

70
80
90
90
115
115
116.5
115

22
25
28
28
30
30
32
32

15
19
24
24
28
28
28
28

95
110
120
120
150
150
150
150

440
505
590
640
685
745
775
845

170
195
215
215
255
255
285
285

205
235
265
265
315
315
345
345

300
345
410
460
455
515
542
615

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

95
140
205
225
305
365
435
495

5
7
10
12
16
18
21
28

Fan

Hight Speed Shaft

Size
9015
9025
9030
9035
9040
9045
9050
9055

W2/Depth

80
80
110
110
110
110
110
110

28k6
35k6
40k6
40k6
45k6
45k6
50k6
50k6

M12/28
M12/28
M16/36
M16/36
M16/36
M16/36
M16/36
M16/36

Key
X2
8
10
14
14
14
14
14
14

Y2
4
5
5.5
5.5
5.5
5.5
5.5
5.5

Z2
7
8
9
9
9
9
9
9

L2
70
70
95
95
95
95
95
95

FA

FB

FC

FD

125
135
150
150
170
170
190
190

125
140
140
140
160
160
160
160

50
50
80
80
80
80
80
80

30
30
52
52
52
52
52
52

Unit: mm
1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions shown in these drawings.

C - 46

4. Refer to the page D -24 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Double Reduction Horizontal Mounting

9015 9055

Hollow Shaft (Shrink Disk Type)

TU2

TU4
U4

T2

V5

V3

V2

Y1

Z1

U1

V1

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

T1

9015
9025
9030
9035
9040
9045
9050
9055

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
65
75
85
90
105
105
115

55
65
75
85
90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature

Shaft
Arrangement

Size

P H A

LR

Low Speed
Shaft
Type Fan

R 2 9015
9025
9030
9035
9040
9045
9050
9055

LL

LB

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9015

9025

9030

9035
9040

9045
9050
9055

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Solid Shaft
Size

Refer to the page D-18 for details.

Double
Reduction

Refer to the page D-18 for details.

W1

Right Angle

X1

T4

9015
9055

V1

U2

V4

T1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal Monoblock

Slow Speed Shaft

Backstop Opposite
(Option)
Side

C - 47

DIMENSIONS Right Angle Shaft Double Reduction Horizontal Mounting

A

FA

FB

X2

Z2

FC
FD

R
L2

FA

Y2

9060 9085

High Speed Shaft

With Fan
Refer to the page D-20 for details.

F
E1

E2

FY

4- J
K

K
DP

D
Y

Dimension Selection
Tables
Tables

O
P

Speed
Reducer

Size

E1

E2

FY

9060
9065
9070
9075
9080
9085

865
911
965
1018
1080
1136

299
338
336
383
378
422

725
771
825
878
940
996

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

183
148
213
178
236
196

578
648
648
718
718
798

212
212
237
237
257
257

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

885
970
1020
1120
1155
1255

310
310
350
350
380
380

380
380
430
430
460
460

615
700
700
800
835
935

DP

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

600
725
920
1170
1300
1560

25
34
37
46
53
67

Fan

Hight Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

140
140
140
140
140
140

60m6
60m6
65m6
65m6
75m6
75m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

Key
X2
18
18
18
18
20
20

Y2
7
7
7
7
7.5
7.5

Z2
11
11
11
11
12
12

L2
125
125
125
125
125
125

FA

FB

FC

FD

220
220
245
245
270
270

160
160
200
200
225
225

105
105
105
105
105
105

65
65
65
65
60
60

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-14 for dimensions not shown in these drawings.

C - 48

W2

4. Refer to the page D-27 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Double Reduction Horizontal Mounting

9060 9085

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

TU4
U4

T2

T4

V5

Z1

Y1

V4

V3

V2

V1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Double
Reduction

9060
9065
9070
9075
9080
9085

Refer to the page D-18 for details.

Right Angle

Solid Shaft
Size

9060
9085

Refer to the page D-18 for details.

W1

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125 123
145 143
145 143
150 148
165 163
175 173
Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

LL

LB

Nomenclature
Shaft
Arrangement

Size

P H D

Low Speed
Shaft
Type Fan

Nominal
Reduction Ratio

R 2 9060
9065
9070
9075
9080
9085

RL
RR
RB
LR
LL
LB

(blank) : Without Fan

F : With Fan

Size
9060

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9065
9070
9075
9080
9085

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Split

X1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Backstop Opposite
(Option)
Side

C - 49

DIMENSIONS Right Angle Shaft Double Reduction Horizontal Mounting

A
C

R
L2

9095, 9105, 9115

FC

Z2

Y2

X2

FA

FB

FA

FD

High Speed Shaft

With Fan

H1

H2

Refer to the page D-20 for details.

H
L

6- J
G

D
Y

O
P

L
DP

Dimension Selection
Tables
Tables

Speed
Reducer

Size

H1

H2

9095
9105
9115

1393
1589
1802

460
500
560

1223
1379
1592

190
210
240

450
500
560

895
995
1120

85
90
100

39
39
46

27
27
34

42
42
48

1090
1220
1390

130
130
140

520
570
630

610
660
730

460
520
595

High Speed Shaft

Size
9095
9105
9115

W2/Depth

170
210
210

90m6
100m6
110m6

M24/50
M24/50
M24/50

Fan
Key

X2
25
28
28

Y2
9
10
10

Z2
14
16
16

L2
150
190
190

FA

FB

FC

FD

340
380
410

250
250
250

135
175
175

90
130
130

In case of continuous load, the forced oil lubrication is necessary. For details, consult us.

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for the dimensions not shown in these drawings.

C - 50

W2

DP

Wt.
kg

1 1/2" 2050
1 1/2" 2800
1 1/2" 3800

Oil
Qty.
L
100
150
200

Unit: mm

4. Refer to the page D -30 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Double Reduction Horizontal Mounting

9095, 9105, 9115

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

T2

Y1

V3

Z1

V2

V1
700
740
830

350
390
420

350
350
410

190m6
220m6
240m6

M30/60
M30/60
M30/60

W1/Depth

V1

U1

Steel
Housing

T1

Double
Reduction

9095
9105
9115

TU1

Right Angle

Solid Shaft
Size

9095
9115

Refer to the page D-18 for details.

W1

Hollow Shaft (Shrink Disk Type)

Key
X1
45
50
56

Y1
15
17
20

Z1
25
28
32

L1
320
320
375

TU2

T2

U2

V2

V3

859
949
1065

509
559
645

350
390
420

203
223
253

200
220
250

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

LL

LB

Nomenclature
Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P H D

R 2 A 9095
9105
9115

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB

Nominal Reduction Ratio

Size

6.3 7.1

10 11.2 12.5 14

16

18

20

9090

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

9095
9100
9105
9110
9115

H
L

Air Breather

Split

X1

TU1
U1
L1

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 51

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

9030 9055

A
R
L2

Z2

X2

BH

FA

FB

Y2

FC
FD

FA

W2

High Speed Shaft

BD

With Fan
Refer to the page D-21 for details.

DP1

F
E1

H
L

4- J
K

K
DP2

Dimension Selection
Tables
Tables

Speed
Reducer

O
P

D
G

Y
L

Size

E1

9030

656

200

576

110

160

320

349

90

28

24

120

590

215

265

410

9035

687

219

607

129

185

370

399

90

28

24

120

640

215

265

460

9040

716

235

636

120

200

400

431

115

30

28

150

685

255

315

455

9045

755

256

675

141

220

440

471

115

30

28

150

745

255

315

515

9050

808

255

728

138.5

210

420

451

116.5

32

28

150

775

285

345

542

9055

847

286

767

171

245

490

521

115

32

28

150

845

285

345

615

High Speed Shaft

Size
9030
9035
9040
9045
9050
9055

W2/Depth

80
80
80
80
80
80

28k6
28k6
30k6
30k6
35k6
35k6

M10/22
M10/22
M10/22
M10/22
M12/28
M12/28

Fan
Key

X2
8
8
8
8
10
10

Y2
4
4
4
4
5
5

Z2
7
7
7
7
8
8

L2
70
70
70
70
70
70

Backstop

FA

FB

FC

FD

150
150
170
170
190
190

125
125
125
125
140
140

50
50
50
50
50
50

30
30
30
30
22
22

BD

150
150

BH

263
263

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
1"
1"
1"
1"

210
230
305
365
445
505

10
12
16
18
21
28

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions shown in these drawings.

C - 52

4. Refer to the page D -24 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

9030 9055

Hollow Shaft (Shrink Disk Type)

TU2

TU4
U4

T2

V5

V3

V2

Y1

Z1

U1

V1

330
330
349
391
411
411

160
160
179
181
201
201

170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
22
25
25
28
28
32

L1
150
150
150
190
190
185

T1

9030
9035
9040
9045
9050
9055

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
9
14
9
14
9
14
10
16
10
16
11
18

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

393
403
448
463
503
528

233
243
268
283
303
323

160
160
180
180
200
205

83
88
98
108
108
123

80
85
95
105
105
120

330
330
360
370
410
410

165
165
180
185
205
205

165
165
180
185
205
205

75
85
90
105
105
115

75
85
90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

LL

LB

Nomenclature
Low Speed
Shaft
Shaft
Arrangement Type Option

Size

P H A

R 3 9030
9035
9040
9045
9050
9055

Nominal
Reduction Ratio

(blank)
F
B
FB

RL
RR
RB
LR
LL
LB

: Without Fan
: With Fan
: With Backstop
: With Fan & Backstop

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9030

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9035
9040
9045
9050
9055

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Solid Shaft
Size

Refer to the page D-18 for details.

Triple
Reduction

Refer to the page D-18 for details.

W1

Right Angle

X1

T4

9030
9055

V1

U2

V4

T1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal Monoblock

Slow Speed Shaft

Backstop Opposite
(Option)
Side

C - 53

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

X2

BH

FA

FB

Z2

FC
FD

R
L2

FA

Y2

9060 9085

W2

High Speed Shaft

BD

With Fan

E1

E2

Refer to the page D-21 for details.

4- J
K

K
DP

Dimension Selection
Tables
Tables

O
P

D
G

Speed
Reducer

Size

E1

E2

9060
9065
9070
9075
9080
9085

939
985
1027
1080
1176
1232

299
338
336
383
378
422

829
875
917
970
1036
1092

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

158
123
183
148
208
168

578
648
648
718
718
798

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

885
970
1020
1120
1155
1255

310
310
350
350
380
380

380
380
430
430
460
460

615
700
700
800
835
935

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

110
110
110
110
140
140

45k6
45k6
50k6
50k6
60m6
60m6

M16/36
M16/36
M16/36
M16/36
M20/42
M20/42

X2
14
14
14
14
18
18

Backstop

Fan
Key
Y2
5.5
5.5
5.5
5.5
7
7

Z2
9
9
9
9
11
11

L2
95
95
95
95
125
125

FA

FB

FC

FD

BD

BH

220
220
245
245
270
270

160
160
160
160
160
160

80
80
80
80
105
105

52
52
52
52
65
65

175
175
190
190
210
210

308
308
330
330
365
365

DP

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

660
785
940
1190
1350
1610

29
33
45
52
60
75

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-14 for dimensions not shown in these drawings.

C - 54

4. Refer to the page D -27 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

9060 9085

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

TU4
U4

T2

T4

Y1

V5

V4

V3

Z1

V2

V1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

U1

T1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
11
18
12
20
12
20
13
22
13
22
15
25

Triple
Reduction

9060
9065
9070
9075
9080
9085

TU1

Refer to the page D-18 for details.

Right Angle

Solid Shaft
Size

9060
9085

Refer to the page D-18 for details.

W1

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125 123
145 143
145 143
150 148
165 163
175 173
Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

LL

LB

Nomenclature
Low Speed
Shaft
Shaft
Arrangement Type Option

Size

P H D

R 3 9060
9065
9070
9075
9080
9085

Nominal
Reduction Ratio

(blank)
F
B
FB

RL
RR
RB
LR
LL
LB

: Without Fan
: With Fan
: With Backstop
: With Fan & Backstop

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9060

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075
9080
9085

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Split

X1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Backstop Opposite
(Option)
Side

C - 55

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

B (90909100)

9090 9115

A
FC

R
L2

FA
FA

FB

X2

Z2

FD

Y2

B
(91059115)

W2

High Speed Shaft

With Fan

F
E1

E2

Refer to the page D-21 for details.

6- J
K1

K2

K3

D
Speed
Reducer

Dimension Selection
Tables
Tables

DP

O
P

Size

E1

E2

K1

K2

K3

9090
9095
9100
9105
9110
9115

1320
1350
1474
1508
1684
1733

428
458
468
493
508
558

1180
1210
1334
1368
1514
1563

345
375
375
410
420
470

375
400
425
450
475
500

750
800
850
900
950
1000

253
258
282
287
303
302

797
847
897
947
997
1047

60
60
70
70
75
75

50
50
55
55
60
60

42
42
48
48
56
56

270
290
300
320
340
350

250
250
280
280
310
310

210
210
240
240
260
260

1440
1500
1610
1680
1810
1910

480
480
560
560
610
610

570
570
650
650
710
710

660
690
735
770
830
880

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

W2/Depth

140
140
140
140
170
170

65m6
65m6
75m6
75m6
85m6
85m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

Fan
Key

X2
18
18
20
20
22
22

Y2
7
7
7.5
7.5
9
9

Z2
11
11
12
12
14
14

L2
125
125
125
125
150
150

FA

FB

FC

FD

340
340
380
380
410
410

200
200
225
225
225
225

105
105
105
105
135
135

65
65
60
60
90
90

DP

Wt.
kg

Oil
Qty.
L

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2150
2400
2880
3440
4160
4610

120
155
180
220
250
310

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D -16 for dimensions shown in these drawings.

C - 56

4. Refer to the page D -30 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

9090 9115

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

T2

V3

V2

V1
Y1

Z1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

U1

T1

Triple
Reduction

9090
9095
9100
9105
9110
9115

TU1

Right Angle

Solid Shaft
Size

9090
9115

Refer to the page D-18 for details.

W1

Hollow Shaft (Shrink Disk Type)

X1
45
45
45
50
50
56

Key
Y1 Z1
15 25
15 25
15 25
17 28
17 28
20 32

L1
270
320
320
320
320
375

TU2 T2

U2

V2

V3

844
859
934
949
1030
1065

350
350
390
390
420
420

193
203
213
223
243
253

190
200
210
220
240
250

494
509
544
559
610
645

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

LL

LB

Nomenclature
Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P H D

R 3 9090
9095
9100
9105
9110
9115

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB

Size
9090

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

80

9095
9100
9105
9110
9115

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Split

X1

TU1
U1
L1

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 57

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

V1

High Speed Shaft

A

W1

Slow Speed Shaft

TU1
R

U1

L2

L1

T1

E1

E2

Z1

W2

X1

Y1

Z2

Y2

X2

9118 9126

K1

K2

K3

DP

6- J

Dimension Selection
Tables
Tables

Speed
Reducer

Size

Ratio

9118

ALL
31.5
35.5
31.5
35.5

9121
9126

1774 608 1604 490

2053 663 1843 545
2013 663 1843 545
2053 663 1843 545
2013 663 1843 545

E1

535 1070
580 1160
580 1160
580 1160
580 1160

E2

K1

K2

K3

343
357
357
357
357

1117
1207
1207
1207
1207

95
95
95
95
95

65
70
70
70
70

56
56
56
56
56

350
390
390
390
390

320
300
300
300
300

260
270
270
270
270

DP

Wt.
kg

Oil
Qty.
L

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

5200
6200
6200
6550
6550

350
460
460
460
460

High Speed Shaft

Size

Ratio

9118

ALL
31.5
35.5
31.5
35.5

9121
9126

W2/Depth

170
210
170
210
170

85m6
110m6
90m6
110m6
90m6

M20/42
M24/50
M24/50
M24/50
M24/50

Key
X2
22
28
25
28
25

Y2
9
10
9
10
9

Z2
14
16
14
16
14

L2
150
190
150
190
150

Solid Shaft
Size
9118
9121
9126

Ratio
ALL
31.5
35.5
31.5
35.5

TU1

T1

U1

V1

W1/Depth

850
935
935
935
935

440
465
465
465
465

410
470
470
470
470

260m6
280m6
280m6
300m6
300m6

M36/70
M36/70
M36/70
M36/70
M36/70

X1
56
63
63
70
70

Key
Y1 Z1 L1
20 32 375
20 32 425
20 32 425
22 36 425
22 36 425
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for the dimensions not shown in these drawings.

C - 58

1990 610
2180 680
2180 680
2180 680
2180 680

710
780
780
780
780

900
995
995
995
995

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

9118 9126

RR

RB

LR

LL

LB

Size
9118

Nominal Reduction Ratio

25

28 31.5 35.5 40

45

50

56

63

71

80

90

9121

9126

(blank) :Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB

H
L

Air Breather

Air Vent

Oil Fill

9118
9121
9126

Triple
Reduction

R 3 -

Nominal
Reduction Ratio

Fan

Right Angle

P H D

9118
9126

Shaft
Arrangement

Size

Split

Nomenclature

RL

PARAMAX Horizontal

Standard Shaft Arrangement Conguration

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 59

W2

W1

Slow Speed Shaft

A

TU1
R

U1

L2

L1

T1

E1

WL
V1

High Speed Shaft

Z1

X2

9128 9136

X1

Y1

Z2

Y2

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

K1

K2

DP

6- J

Y3
L

Dimension Selection
Tables
Tables

Speed
Reducer

Size

9128
9131
9136

2244
2479
2479

680 2034
730 2269
730 2269

330
330
330

E1

600 1194 1241 140

630 1256 1303 140
630 1256 1303 140

K1

K2

55
60
60

66
66
66

940
940
940

280 1930
280 2070
280 2070

High Speed Shaft

Size
9128
9131
9136

W2/Depth

210
210
210

100m6
110m6
110m6

M24/50
M24/50
M24/50

Key
X2
28
28
28

Y2
10
10
10

Wt.
kg

DP
Z2
16
16
16

L2
190
190
190

Oil
Qty.
L

1 1/2" 7400 350

1 1/2" 9850 510
1 1/2" 10200 500

Solid Shaft
Size
9128
9131
9136

TU1

T1

U1

V1

W1/Depth

WL

950
1100
1110

480
550
560

470
550
550

320m6
340m6
360m6

M36/70
M36/70
M36/70

200
215
230

Key
X1
70
80
80

Y1
22
25
25

Z1
36
40
40

L1
425
500
500
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for the dimensions not shown in these drawings.

C - 60

Y3

170
200
200

710
850
850

840
980
980

660
660
660

990
1130
1130

DIMENSIONS Right Angle Shaft Triple Reduction Horizontal Mounting

9128 9136

RR

RB

LR

LL

LB

50

56

63

71

80

9131

9136

45

28 31.5 35.5 40

9128

Size

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

(blank) :Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB

Steel
Housing

Triple
Reduction

R 3 A 9128
9131
9136

Nominal
Reduction Ratio

Fan

Right Angle

P H D

9128
9136

Shaft
Arrangement

Size

Split

Nomenclature

RL

PARAMAX Horizontal

Standard Shaft Arrangement Conguration

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 61

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

A
C

X2

BH

Z2

R
L2

Y2

9040 9055

W2

High Speed Shaft

BD

DP1

F
E1

H
L

Dimension Selection
Tables
Tables

4- J
K

Speed
Reducer

D
DP2

O
P

Size

E1

9040

790

235

710

120

200

400

431

115

30

28

150

759

255

315

529

9045

829

256

749

141

220

440

471

115

30

28

150

819

255

315

589

9050

859

255

779

138.5

210

420

451

116.5

32

28

150

848

285

345

615

9055

898

286

818

171

245

490

521

115

32

28

150

918

285

345

688

High Speed Shaft

Size
9040
9045
9050
9055

W2/Depth

80
80
80
80

28k6
28k6
28k6
28k6

M10/22
M10/22
M10/22
M10/22

Backstop
Key

X2
8
8
8
8

Y2
4
4
4
4

Z2
7
7
7
7

L2
70
70
70
70

BD

150
150

BH

263
263

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"

1"
1"
1"
1"

325
395
460
520

19
21
24
29
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-13 for dimensions shown in these drawings.

C - 62

4. Refer to the page D -24 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

9040 9055

Hollow Shaft (Shrink Disk Type)

TU2

TU4
U4

T2

V5

V3

V2

Y1

Z1

T1

U1

V1

W1/Depth

349
391
411
411

179
181
201
201

170 95m6
210 105m6
210 110m6
210 120m6

M24/50
M24/50
M24/50
M24/50

Hollow Shaft (Shrink Disk Type)

X1
25
28
28
32

Key
Y1
Z1
9
14
10
16
10
16
11
18

L1
150
190
190
185

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

448
463
503
528

268
283
303
323

180
180
200
205

98
108
108
123

95
105
105
120

360
370
410
410

180
185
205
205

180
185
205
205

90
105
105
115

90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

LL

LB

Nomenclature
Low Speed
Shaft
Shaft
Option
Arrangement Type

Size

P H A

R 4 9040
9045
9050
9055

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB

(blank) : Without Option

B : With Backstop

Size
9040

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9045

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 63

9040
9045
9050
9055

TU1

Refer to the page D-18 for details.

Solid Shaft
Size

Refer to the page D-18 for details.

W1

Right Angle Quadruple

Reduction

X1

T4

9040
9055

V1

U2

V4

T1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal Monoblock

Slow Speed Shaft

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

A
R
L2

BH

Y2

X2

Z2

9060 9085

W2

High Speed Shaft

F
E1

E2

BD

Dimension Selection
Tables
Tables

Speed
Reducer

4- J
K

O
P

D
DP

Y
L

Size

E1

E2

9060

950

299

870

151

265

530

121

578

135

35

35

180

970

310

380

700

9065

996

338

916

190

300

600

86

648

135

35

35

180

1055

310

380

785

9070

1080

336

1000

163

300

600

140

648

160

40

42

215

1115

350

430

795

9075

1133

383

1053

210

335

670

105

718

160

52

42

220

1215

350

430

895

9080

1250

378

1140

205

335

670

162

718

160

52

42

220

1275

380

460

955

9085

1306

422

1196

249

375

750

122

798

160

52

42

220

1375

380

460

1055

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

80
80
80
80
110
110

30k6
30k6
35k6
35k6
45k6
45k6

M10/22
M10/22
M12/28
M12/28
M16/36
M16/36

Backstop
Key

X2
8
8
10
10
14
14

Y2
4
4
5
5
5.5
5.5

Z2
7
7
8
8
9
9

L2
70
70
70
70
95
95

BD

BH

175
175
190
190
210
210

308
308
330
330
365
365

DP

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

670
825
960
1180
1390
1650

38
43
57
67
73
90

Unit: mm
1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-15 for dimensions shown in these drawings.

C - 64

4. Refer to the page D -27 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

9060 9085

Hollow Shaft (Shrink Disk Type)

TU2

T1

TU4

U2

U4

T2

T4

9075
9080
9085

V5

V4

V3

Z1

V2

V1
Y1
9070

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Nomenclature

LR

Low Speed
Shaft
Shaft
Arrangement Type Option

Size

P H D

RB

R 4 9060
9065
9070
9075
9080
9085

LL

LB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB

(blank) : Without Option

B : With Backstop

Size

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9060

9065

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

9070

9075
9080

9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 65

9065

T1

Hollow Shaft (Key Type)

9060

TU1

Refer to the page D-18 for details.

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
11
18
12
20
12
20
13
22
13
22
15
25

Right Angle Quadruple

Reduction

Solid Shaft
Size

9060
9085

Refer to the page D-18 for details.

W1

Split

X1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

B (90909100)

9090 9115

Y2

X2

Z2

R
L2

B
(91059115)

W2

F
E1

E2

High Speed Shaft

6- J
K1

Dimension Selection
Tables
Tables

Speed
Reducer

K2

K3

D
DP

O
P

Size

E1

E2

K1

K2

K3

9090

1382

428

1272

345

375

750

198

797

60

50

42

270

250

210

1440

480

570

660

9095

1412

458

1302

375

400

800

203

847

60

50

42

290

250

210

1500

480

570

690

9100

1570

468

1430

375

425

850

215

897

70

55

48

300

280

240

1610

560

650

735

9105

1604

493

1464

410

450

900

220

947

70

55

48

320

280

240

1680

560

650

770

9110

1670

508

1530

420

475

950

225

997

75

60

56

340

310

260

1810

610

710

830

9115

1719

558

1579

470

500

1000

224

1047

75

60

56

350

310

260

1910

610

710

880

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

W2/Depth

110
110
140
140
140
140

50k6
50k6
60m6
60m6
60m6
60m6

M16/36
M16/36
M20/42
M20/42
M20/42
M20/42

Key
X2
14
14
18
18
18
18

Y2
5.5
5.5
7
7
7
7

Z2
9
9
11
11
11
11

L2
95
95
125
125
125
125

DP

Wt.
kg

Oil
Qty.
L

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2150
2400
2880
3440
4060
4510

150
180
210
255
300
360

Unit: mm
1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-16 for dimensions shown in these drawings.

C - 66

4. Refer to the page D -30 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

9090 9115

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

T2

V3

V2

V1
Y1

Z1

T1

U1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

X1
45
45
45
50
50
56

Y1
15
15
15
17
17
20

Z1
25
25
25
28
28
32

L1
270
320
320
320
320
375

TU2

T2

U2

V2

V3

844
859
934
949
1030
1065

494
509
544
559
610
645

350
350
390
390
420
420

193
203
213
223
243
253

190
200
210
220
240
250

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P H D

LR

R 4 9090
9095
9100
9105
9110
9115

LL

LB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

Size
9090

Nominal Reduction Ratio

90 100 112 125 140 160 180 200 224 250 280 315 355 400

9095
9100
9105
9110
9115

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 67

TU1

Hollow Shaft (Shrink Disk Type)

Key

9090
9095
9100
9105
9110
9115

Right Angle Quadruple

Reduction

Solid Shaft
Size

9090
9115

Refer to the page D-18 for details.

W1

Split

X1

TU1
U1
L1

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

W2

TU1

E2

U1

L2

L1

T1

K1

K2

E1

W1

Slow Speed Shaft

A
C

K3

6- J

D
DP

Z1

V1

High Speed Shaft

X1

Y1

Z2

Y2

X2

9118 9126

Dimension Selection
Tables
Tables

Speed
Reducer

Size
9118
9121
9126

1760 608 1620 490

1970 663 1830 545
1970 663 1830 545

E1

535 1070
580 1160
580 1160

E2

263 1117
257 1207
257 1207

K1

K2

K3

95
95
95

65
70
70

56
56
56

350
390
390

320
300
300

260
270
270

1990
2180
2180

610
680
680

710
780
780

900
995
995

DP

Wt.
kg

High Speed Shaft

Size
9118
9121
9126

W2/Depth

140
140
140

60m6
65m6
65m6

M20/42
M20/42
M20/42

Key
X2
18
18
18

Y2
7
7
7

Z2
11
11
11

L2
125
125
125

1 1/2" 5100
1 1/2" 6150
1 1/2" 6450

Solid Shaft
Size
9118
9121
9126

TU1

T1

U1

V1

W1/Depth

850
935
935

440
465
465

410
470
470

260m6
280m6
300m6

M36/70
M36/70
M36/70

Key
X1
56
63
70

Y1
20
20
22

Z1
32
32
36

L1
375
425
425
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for the dimensions not shown in these drawings.

C - 68

Oil
Qty.
L
390
540
530

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

9118 9126

RR

RB

LR

LL

LB

Size

Nominal Reduction Ratio

90 100 112 125 140 160 180 200 224 250 280 315 355 400

9121

9126

9118

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 69

RL
RR
RB
LR
LL
LB

9118
9121
9126

R 4

Nominal
Reduction Ratio

Right Angle Quadruple

Reduction

P H D

9118
9126

Shaft
Arrangement

Size

Split

Nomenclature

RL

PARAMAX Horizontal

Standard Shaft Arrangement Conguration

W2

WL
V1

High Speed Shaft

Z1

X2

9128 9136

X1

Y1

Z2

Y2

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

W1

Slow Speed Shaft

B

TU1
R

U1

L2

L1

T1

E1

K1

K2

DP

Y3

M
6- J

Dimension Selection
Tables
Tables

Speed
Reducer

Size

9128
9131
9136

2163
2410
2410

680 2023
730 2240
730 2240

330
330
330

E1

600 1194 1241 140

630 1256 1303 140
630 1256 1303 140

K1

K2

55
60
60

66
66
66

940
940
940

280 1990
280 2170
280 2170

High Speed Shaft

Size
9128
9131
9136

W2/Depth

140
170
170

75m6
85m6
85m6

M20/42
M20/42
M20/42

Key
X2
20
22
22

Y2
7.5
9
9

Wt.
kg

DP
Z2
12
14
14

L2
125
150
150

Oil
Qty.
L

1 1/2" 7400 460

1 1/2" 9850 680
1 1/2" 10200 660

Solid Shaft
Size
9128
9131
9136

TU1

T1

U1

V1

W1/Depth

WL

950
1100
1110

480
550
560

470
550
550

320m6
340m6
360m6

M36/70
M36/70
M36/70

200
215
230

Key
X1
70
80
80

Y1
22
25
25

Z1
36
40
40

L1
425
500
500
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for the dimensions not shown in these drawings.

C - 70

Y3

170
200
200

710
850
850

840
980
980

660
660
660

1050
1230
1230

DIMENSIONS Right Angle Shaft Quadruple Reduction Horizontal Mounting

9128 9136

RR

RB

LR

LL

LB

Size

Nominal Reduction Ratio

71

80

90 100 112 125 140 160 180 200 224 250 280 315 355

9131

9136

9128

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 71

Steel
Housing

H
L

RL
RR
RB
LR
LL
LB

9128
9131
9136

R 4 A -

Nominal
Reduction Ratio

Right Angle Quadruple

Reduction

P H D

9128
9136

Shaft
Arrangement

Size

Split

Nomenclature

RL

PARAMAX Horizontal

Standard Shaft Arrangement Conguration

DIMENSIONS Right Angle Shaft Double Reduction Vertical Mounting

A
C

9015 9055

R
L2

N1

N2

H
L

NP

E2

E3

C1

FC
FD

Z2

X2

FA

E1
O

FB

FA

Y2

DP1

RI

W2

High Speed Shaft

K

K
D

DP2 G

4- J
G

Refer to the page D-20 for details.

Speed
Reducer

Dimension Selection
Tables
Tables

With Fan

Size

C1

E1

E2

E3

RI

9015
9025
9030
9035
9040
9045
9050
9055

507
545
645
676
705
744
755
794

160
175
200
219
235
256
255
286

427
465
535
566
595
634
645
684

115
135
155
186
180
219
210
249

140
155
175
194
205
226
225
256

270
310
320
370
400
440
420
490

195
215
220
245
260
266
270
305

135
155
160
185
200
220
210
245

20
20
25
25
30
30
30
30

35
40
50
50
60
60
60
60

80
87.5
105
120
120
140
140
155

15
19
24
24
28
28
28
28

95
110
120
120
150
150
150
150

440
505
590
640
685
745
775
845

High Speed Shaft

Size
9015
9025
9030
9035
9040
9045
9050
9055

W2/Depth

80
80
110
110
110
110
110
110

28k6
35k6
40k6
40k6
45k6
45k6
50k6
50k6

M12/28
M12/28
M16/36
M16/36
M16/36
M16/36
M16/36
M16/36

N1

70 189 25
75 201.5 23
85 224 22
100 224 22
100 241.5 15
120 241.5 17.5
110 252 23
135 252 23

Fan
Key

X2
8
10
14
14
14
14
14
14

Y2
4
5
5.5
5.5
5.5
5.5
5.5
5.5

Z2
7
8
9
9
9
9
9
9

L2
70
70
95
95
95
95
95
95

FA

FB

FC

FD

125
135
150
150
170
170
190
190

125
140
140
140
160
160
160
160

50
50
80
80
80
80
80
80

30
30
52
52
52
52
52
52

N2

NP

14
12
9
9
2
2
7
7

100
100
117
117
117
117
137
137

230
270
270
320
340
380
360
430

102.5
117.5
132.5
132.5
157.5
157.5
172.5
172.5

260
310
365
396
420
459
490
529

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

95
140
205
225
305
365
435
495

5
7
7
9
19
23
20
26

Unit: mm
1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions shown in these drawings.

C - 72

4Refer to the page D -25 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Double Reduction Vertical Mounting

9015 9055

9015
9025
9030
9035
9040
9045
9050
9055

V5

V4

V3

V2
Z1

TU1

T1

U1

V1

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

Solid Shaft
Size

Refer to the page D-18 for details.

Refer to the page D-18 for details.

W1

Double
Reduction

X1

T4

Right Angle

Y1

TU4
U4

T2

9015
9055

V1

U2

T1

TU2

U1
L1

TU1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
65
75
85
90
105
105
115

55
65
75
85
90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P V A

R 2 9015
9025
9030
9035
9040
9045
9050
9055

Nominal
Reduction Ratio

RL
RR

(blank) : Without Fan

F : With Fan
(blank) :Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

Size

6.3

7.1

10

14

16

18

9015

9025

9030

9035
9040

9045
9050
9055

11.2 12.5

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 73

DIMENSIONS Right Angle Shaft Double Reduction Vertical Mounting

9060 9085

A
R
L2

N
N1

P1

NP

E2

E3

C1

FA

E1
O

FB

FA

Y2

W2

RI

High Speed Shaft

With Fan
K
DP2 G

K
D

4- J
G

Refer to the page D-20 for details.

* Refer to footnote 3.

Speed
Reducer

Dimension Selection
Tables
Tables

X2

Z2

FC
FD

DP1

E3

RI

9060

865 299 725 245 251 530 282 265

35

35

160

35

180 885 140 272

9065

911 338 771 291 290 600 317 300

35

35

175

35

180

9070

965 336 825 285 283 600 317 300

40

40

175

42

9075 1018 383 878 338 330 670 352 335

40

52

190

42

9080 1080 378 940 330 325 670 352 335

40

52

190

9085 1136 422 996 386 369 750 392 375

40

52

215

Size

C1

E1

E2

N1

NP

35

137 460

190

229 564

175 272

38

137 530

190

229 610

215 1020 155 303

38

137 520

215

262 657

220 1120 195 303

40

137 590

215

262 710

42

220 1155 170 323

45

137 590

230

295 750

42

220 1255 210 323

40

137 670

230

295 806

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

140
140
140
140
140
140

60m6
60m6
65m6
65m6
75m6
75m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

970

Fan
Key

X2
18
18
18
18
20
20

Y2
7
7
7
7
7.5
7.5

Z2
11
11
11
11
12
12

L2
125
125
125
125
125
125

FA

FB

FC

FD

220
220
245
245
270
270

160
160
200
200
225
225

105
105
105
105
105
105

65
65
65
65
60
60

DP1

DP2

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

Wt.
kg

P1

Oil
Qty.
L

600
725 Refer
920 to the
1170 next
1300 page.
1560
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with oil gauge. Refer to the page D-28.

C - 74

4. Refer to the page D-14 for dimensions shown in these drawings.

5. Refer to the page D -28 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Double Reduction Vertical Mounting

9060 9085

Z1

V5

V4

V3

V2

V1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

9060
9065
9070
9075
9080
9085

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
11
18
12
20
12
20
13
22
13
22
15
25

Solid Shaft
Size

Refer to the page D-18 for details.

Double
Reduction

Refer to the page D-18 for details.

W1

Right Angle

X1

T4

9060
9085

Y1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Approx. Oil Qty.

Size

6.3-9
25

9060
9065
9070
9075
9080
9085

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P V D

46

Nominal
Reduction Ratio

R 2 9060
9065
9070
9075
9080
9085

35

Nominal Reduction Ratio

10-18
8-11.2 12.5-22.4
25
32
32
41
47
54
55
58
68
Unit: liters

RL
RR

(blank) : Without Fan

F : With Fan

Size
9060

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9065
9070
9075
9080
9085

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 75

DIMENSIONS Right Angle Shaft Triple Reduction Vertical Mounting

A
C

9030 9055

R
L2

N1

N2

H
L

NP

E2

C1

E3

FA

E1
O
DP2 G

K
D

High Speed Shaft

With Fan

4- J
G

W2

RI

Refer to the page D-21 for details.

Speed
Reducer

Dimension Selection
Tables
Tables

X2

FB

FA

Y2

DP1

Z2

FC
FD

Size

C1

E1

E2

E3

RI

9030
9035
9040
9045
9050
9055

656
687
716
755
808
847

200
219
235
256
255
286

576
607
636
675
728
767

264
295
306
345
358
397

175
194
205
226
225
256

320
370
400
440
420
490

220
245
260
266
270
305

160
185
200
220
210
245

25
25
30
30
30
30

50
50
60
60
60
60

105
120
120
140
140
155

24
24
28
28
28
28

120
120
150
150
150
150

590
640
685
745
775
845

85
100
100
120
110
135

High Speed Shaft

Size
9030
9035
9040
9045
9050
9055

W2/Depth

80
80
80
80
80
80

28k6
28k6
30k6
30k6
35k6
35k6

M10/22
M10/22
M10/22
M10/22
M12/28
M12/28

N1

211 22
211 22
237.5 15
237.5 17.5
257.5 23
257.5 23

Fan
Key

X2
8
8
8
8
10
10

Y2
4
4
4
4
5
5

Z2
7
7
7
7
8
8

L2
70
70
70
70
70
70

FA

FB

FC

FD

150
150
170
170
190
190

125
125
125
125
140
140

50
50
50
50
50
50

30
30
30
30
22
22

N2

NP

9
9
2
2
7
7

100
100
117
117
117
117

270
320
340
380
360
430

132.5
132.5
157.5
157.5
172.5
172.5

365
396
420
459
490
529

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
1"
1"
1"
1"

210
230
305
365
445
505

9
12
18
22
21
30

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions shown in these drawings.

C - 76

4. Refer to the page D -25 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Triple Reduction Vertical Mounting

9030 9055

V5

V4

V3

V2
Z1

Y1

V1

V1

330
330
349
391
411
411

160
160
179
181
201
201

170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
22
25
25
28
28
32

L1
150
150
150
190
190
185

U1

T1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
9
14
9
14
9
14
10
16
10
16
11
18

Triple
Reduction

TU1

Refer to the page D-18 for details.

Right Angle

Refer to the page D-18 for details.

Solid Shaft

9030
9035
9040
9045
9050
9055

T4

9030
9055

X1

W1

Size

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

393
403
448
463
503
528

233
243
268
283
303
323

160
160
180
180
200
205

83
88
98
108
108
123

80
85
95
105
105
120

330
330
360
370
410
410

165
165
180
185
205
205

165
165
180
185
205
205

75
85
90
105
105
115

75
85
90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P V A

R 3 9030
9035
9040
9045
9050
9055

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR

Size
9030

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9035
9040
9045
9050
9055

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 77

DIMENSIONS Right Angle Shaft Triple Reduction Vertical Mounting

9060 9085

A
R
L2

N
N1

P1

NP

E2

E3

C1

FA

E1
O

FB

FA

Y2

X2

W2

RI

K
DP2 G

K
D

Speed
Reducer

High Speed Shaft

With Fan

4- J
G

Refer to the page D-21 for details.

Dimension Selection
Tables
Tables

Z2

FC
FD

DP1

* Refer to footnote 3.

E3

RI

9060

Size

939 299 829 414 251 530 282 265

C1

E1

E2

35

35

160

35

180 885 140 277.5 35

N1

117 460 190 213 564

NP

P1

9065

985 338 875 460 290 600 317 300

35

35

175

35

180 970 175 277.5 38

117 530 190 213 610

9070 1027 336 917 482 283 600 317 300

40

40

175

42

215 1020 155 302.5 38

117 520 215 233 657

9075 1080 383 970 535 330 670 352 335

40

52

190

42

220 1120 195 302.5 40

117 590 215 233 710

9080 1176 378 1036 556 325 670 352 335

40

52

190

42

220 1155 170 322.5 45

117 590 230 268 750

9085 1232 422 1092 612 369 750 392 375

40

52

215

42

220 1255 210 322.5 40

117 670 230 268 806

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

110
110
110
110
140
140

45k6
45k6
50k6
50k6
60m6
60m6

M16/36
M16/36
M16/36
M16/36
M20/42
M20/42

Fan
Key

X2
14
14
14
14
18
18

Y2
5.5
5.5
5.5
5.5
7
7

Z2
9
9
9
9
11
11

L2
95
95
95
95
125
125

FA

FB

FC

FD

220
220
245
245
270
270

160
160
160
160
160
160

80
80
80
80
105
105

52
52
52
52
65
65

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

660
785
940
1190
1350
1610

28
35
46
59
60
80

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with oil gauge. Refer to the page D-28.

C - 78

4. Refer to the page D-14 for dimensions shown in these drawings.

5. Refer to the page D -28 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Triple Reduction Vertical Mounting

9060 9085

Z1

V5

V4

V3

V2

V1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

9060
9065
9070
9075
9080
9085

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
11
18
12
20
12
20
13
22
13
22
15
25

Solid Shaft
Size

Refer to the page D-18 for details.

Triple
Reduction

Refer to the page D-18 for details.

W1

Right Angle

X1

T4

9060
9085

Y1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P V D

R 3 9060
9065
9070
9075
9080
9085

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR

Size
9060

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075
9080
9085

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 79

DIMENSIONS Right Angle Shaft Triple Reduction Vertical Mounting

9090 9115

* Refer to footnote 3.
A
C

R
L2

N1

P
H

P1

NP

E2
DP2

E2
(9090,9095)

C1

E3

FC

Dimension Selection
Tables
Tables

Speed
Reducer

9090
9095
9100
9105
9110
9115

FB

Refer to the page D-21 for details.

C1

E1

E2

E3

E4

RI

N1

NP

1320 410 1180 640 345 750 449 421 430

60

50

215

42

1350 440 1210 670 375 800 474 446 430

60

50

235

42

180 1440 130 381

50

137 630 285 363 975

200 1500 140 381

50

1474 450 1334

375 850 471 471 500

70

55

235

137 680 285 363 1005

48

200 1610 150

60

1508 485 1368

410 900 496 496 500

70

55

710 325

411 1095

260

48

220 1680 160

60

760 325

1684 500 1514

420 950 521 521 500

75

411 1130

60

265

56

220 1810 170

55

800 355 446 1240

1733 550 1563

470 1000 546 546 500

75

60

280

56

250 1910 180

55

850 355 446 1290

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

W2/Depth

140
140
140
140
170
170

65m6
65m6
75m6
75m6
85m6
85m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

X2
18
18
20
20
22
22

Fan
Key
Y2
7
7
7.5
7.5
9
9

Z2
11
11
12
12
14
14

L2
125
125
125
125
150
150

FA

FB

FC

FD

340
340
380
380
410
410

200
200
225
225
225
225

105
105
105
105
135
135

65
65
60
60
90
90

9100 ~ 9115 CTGGSWKRRGFYKVJOQVQTFTKXGPRWORU(QTFGVCKNUEQPUWNVWU

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with oil gauge. Refer to the page D-31.

C - 80

High Speed Shaft

With Fan

DP1

Size

4- J

K
D

W2

RI

K
G

Z2

Y2

X2

FA

E4

E1
O

FA

FD

DP1

DP2

1"
1"
1"
1"
1"
1"

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

Wt.
kg

P1

Oil
Qty.
L

2170 120
2430 145
2970 170
3450 210
4150 230
4670 290
Unit: mm

4. Refer to the page D-16 for dimensions shown in these drawings.

5. Refer to the page D -31 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Triple Reduction Vertical Mounting

9090 9115

V3

V2

V1

Z1

T1

U1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

9090
9095
9100
9105
9110
9115

TU1

Solid Shaft
Size

Triple
Reduction

Refer to the page D-18 for details.

W1

Right Angle

X1

9090
9115

Y1

T2

U2

TU2
T1

TU1
U1
L1

Split

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

Key
X1
45
45
45
50
50
56

Y1
15
15
15
17
17
20

Z1
25
25
25
28
28
32

L1
270
320
320
320
320
375

TU2

T2

U2

V2

V3

844
859
934
949
1030
1065

494
509
544
559
610
645

350
350
390
390
420
420

193
203
213
223
243
253

190
200
210
220
240
250

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P V D

R 3 9090
9095
9100
9105
9110
9115

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR

Size
9090

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

80

9095
9100
9105
9110
9115

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 81

DIMENSIONS Right Angle Shaft Quadruple Reduction Vertical Mounting

B

A
C

9040 9055

R
L2

N1

H
L

NP

E2

E3

C1

Z2

X2

E1
O

Y2

M1

M2

DP2

M1

RI

W2

High Speed Shaft

K

Dimension Selection
Tables
Tables

DP1 G

Speed
Reducer

K
Y

4- J
G

Size

C1

E1

E2

E3

RI

M1

M2

N1

NP

9040

790

235

710

398

205

400

260

200

30

60

120

28

150

759

100

70

228.5

15

100

340 157.5 494

9045

829

256

749

437

226

440

277

220

30

60

140

28

150

819

120

90

228.5 17.5 100

380 157.5 533

9050

859

255

779

467

225

420

270

210

30

60

140

28

150

848

110

83

248.5

23

100

360 172.5 563

9055

898

286

818

506

256

490

305

245

30

60

155

28

150

918

135

118 248.5

23

100

430 172.5 602

High Speed Shaft

Size

9040
9045
9050
9055

W2/Depth

80
80
80
80

28k6
28k6
28k6
28k6

M10/22
M10/22
M10/22
M10/22

Key
X2

Y2

Z2

L2

8
8
8
8

4
4
4
4

7
7
7
7

70
70
70
70

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"

1"
1"
1"
1"

325
395
460
520

18
22
24
34

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-13 for dimensions shown in these drawings.

C - 82

4. Refer to the page D -25 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Quadruple Reduction Vertical Mounting

9040 9055

V5

V4

V3

V2
Z1

Y1

V1

U1

V1

W1/Depth

349
391
411
411

179
181
201
201

170 95m6
210 105m6
210 110m6
210 120m6

M24/50
M24/50
M24/50
M24/50

X1
25
28
28
32

L1
150
190
190
185

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

448
463
503
528

268
283
303
323

180
180
200
205

98
108
108
123

95
105
105
120

360
370
410
410

180
185
205
205

180
185
205
205

90
105
105
115

90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

LR

LL

Nomenclature
Shaft
Arrangement

Size

P V A

R 4 9040
9045
9050
9055

Low Speed
Shaft
Type

Nominal
Reduction Ratio

LR
LL

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9040

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9045
9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 83

T1

Hollow Shaft (Key Type)

TU1

Refer to the page D-18 for details.

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
9
14
10
16
10
16
11
18

Right Angle Quadruple

Reduction

Refer to the page D-18 for details.

Solid Shaft

9040
9045
9050
9055

T4

9040
9055

X1

W1

Size

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

DIMENSIONS Right Angle Shaft Quadruple Reduction Vertical Mounting

B

9060 9085

A
R
L2

N1

P
H

P1

NP

E2

E3

C1

Z2

X2

E1
O

Y2

M1

M2

DP1

M1
G

Dimension Selection
Tables
Tables

High Speed Shaft

*Refer to
footnote 3.

K
Speed
Reducer

4- J
G

DP2

Size

C1

9060
9065
9070
9075
9080
9085

950

299

870

996

338

916

E1

E2

E3

RI

M1

M2

540

251 530 282 265

35

35

160

35

180

970

140

118 277.5

35

117

460 190 203 649

586

290 600 317 300

35

35

175

35

180 1055 175 153 277.5

38

117

530 190 203 695

1080 336 1000 630

283 600 317 300

40

40

175

42

215 1115 155 128 302.5

38

117

520 215 233 752

1133 383 1053 683

330 670 352 335

40

52

190

42

220 1215 195 163 302.5

40

117

590 215 233 805

1250 378 1140 725

325 670 352 335

40

52

190

42

220 1275 170 140 322.5

45

117

590 230 263 870

1306 422 1196 781

369 750 392 375

40

52

215

42

220 1375 210 180 322.5

40

117

670 230 263 926

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

80
80
80
80
110
110

30k6
30k6
35k6
35k6
45k6
45k6

M10/22
M10/22
M12/28
M12/28
M16/36
M16/36

Key
X2
8
8
10
10
14
14

Y2
4
4
5
5
5.5
5.5

Z2
7
7
8
8
9
9

L2
70
70
70
70
95
95

DP1

DP2

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement LR is equipped with oil gauge. Refer to the page D-28.

C - 84

W2

RI

Wt.
kg

N1

NP

P1

Oil
Qty.
L

670
36
825
45
960
54
1180
68
1390
69
1650
94
Unit: mm

4. Refer to the page D-15 for dimensions shown in these drawings.

5. Refer to the page D -28 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Quadruple Reduction Vertical Mounting

9060 9085

V5

Z1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

Hollow Shaft (Shrink Disk Type)

X1
32
36
36
40
40
45

Key
Y1
Z1
11
18
12
20
12
20
13
22
13
22
15
25

L1
185
225
225
275
275
270

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

LR

LL

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V D

R 4 9060
9065
9070
9075
9080
9085

Nominal
Reduction Ratio

LR
LL

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9060

9065
9070

9075
9080

9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 85

9060
9065
9070
9075
9080
9085

TU1

Refer to the page D-18 for details.

Solid Shaft

Right Angle Quadruple

Reduction

Refer to the page D-18 for details.

W1

Size

V4

V3

V2

V1
X1

T4

9060
9085

Y1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

DIMENSIONS Right Angle Shaft Quadruple Reduction Vertical Mounting

9090 9115

* Refer to footnote 3.

A
C

R
L2

N1

P
H

P1

NP

DP2

E2

E3

Z2

X2

E4

E1
O

Y2

C1

RI

W2

High Speed Shaft

K
G

Dimension Selection
Tables
Tables

Speed
Reducer

K
D

4- J
G

Y
L

DP1

Size
9090
9095
9100
9105
9110
9115

C1

E1

E2

E3

E4

RI

1382 410 1272 837 345 750 449 421 430

60

50

215

42

1412 440 1302 867 375 800 474 446 430

60

50

235

42

1570 450 1430 950 375 850 499 471 500

70

55

235

1604 485 1464 984 410 900 524 496 500

70

55

1670 500 1530 1050 420 950 559 521 500

75

1719 550 1579 1099 470 1000 584 546 500

75

N1

NP

180 1440 130 381

50

137 630 285 354 975

200 1500 140 381

50

137 680 285 354 1005

48

200 1610 150 421

60

137 710 325 399 1095

260

48

220 1680 160 421

60

137 760 325 399 1130

60

265

56

220 1810 170 451

55

137 800 355 429 1240

60

280

56

250 1910 180 451

55

137 850 355 429 1290

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

W2/Depth

110
110
140
140
140
140

50k6
50k6
60m6
60m6
60m6
60m6

M16/36
M16/36
M20/42
M20/42
M20/42
M20/42

Key
X2
14
14
18
18
18
18

Y2
5.5
5.5
7
7
7
7

Z2
9
9
11
11
11
11

L2
95
95
125
125
125
125

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2170
2430
2970
3450
4100
4620

120
155
180
220
250
315

P1

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement LR is equipped with oil gauge. Refer to the page D-31.

C - 86

4. Refer to the page D-16 for dimensions shown in these drawings.

5. Refer to the page D -31 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Quadruple Reduction Vertical Mounting

9090 9115

V3

V2

V1
9090
9095
9100
9105
9110
9115

Z1

TU1

T1

U1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

Hollow Shaft (Shrink Disk Type)

Key
X1
45
45
45
50
50
56

Y1
15
15
15
17
17
20

Z1
25
25
25
28
28
32

L1
270
320
320
320
320
375

TU2

T2

U2

V2

V3


859
934
949
1030
1065

494
509
544
559
610
645

350
350
390
390
420
420

193
203
213
223
243
253

190
200
210
220
240
250
Unit: mm

Standard Shaft Arrangement Conguration

LR

LL

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V D

R 4 9090
9095
9100
9105
9110
9115

Nominal
Reduction Ratio

LR
LL

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

Size
9090

Nominal Reduction Ratio

90 100 112 125 140 160 180 200 224 250 280 315 355 400

9095
9100
9105
9110
9115

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 87

Solid Shaft

Refer to the page D-18 for details.

W1

Size

Right Angle Quadruple

Reduction

X1

9090
9115

Y1

T2

U2

TU2
T1

TU1
U1
L1

Split

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

DIMENSIONS Right Angle Shaft Double Reduction Upright Mounting

FA

FA
DP1

Y3

Z2

Y2

FD

FC

FB

X2

H2

W2

9015 9055

High Speed Shaft

With Fan
E

4- J2
K3

R
L2

Refer to the page D-20 for details.

H1
K3

Y4
L

H
L

4- J1

Dimension Selection
Tables
Tables

Speed
Reducer

K1

Y1
K2

K1
Y2
E1
F

K2
P

Size

9015
9025
9030
9035
9040
9045
9050
9055

507
545
645
676
705
744
755
794

160
175
200
219
235
256
255
286

427 90 135
465 95 155
535 110 160
566 129 185
595 120 200
634 141 220
645 138.5 210
684 171 245

E1
270
310
320
370
400
440
420
490

298 70
338 80
348 90
398 90
430 115
470 115
450 116.5
520 115

H1

H2

J1

J2

K1

K2

K3

Y1

Y2

Y3

Y4

50
55
60
60
75
75
75
75

22
25
28
28
30
30
32
32

15
19
24
24
28
28
28
28

15
19
24
24
28
28
28
28

70
75
85
100
100
120
110
135

35
40
50
50
60
60
60
60

95
110
120
120
150
150
150
150

440
505
590
640
685
745
775
845

205
235
265
265
315
315
345
345

170
195
215
215
255
255
285
285

180
210
200
250
260
300
280
350

170
195
215
215
255
255
285
285

300
345
410
460
455
515
542
615

High Speed Shaft

Size
9015
9025
9030
9035
9040
9045
9050
9055

W2/Depth

80
80
110
110
110
110
110
110

28k6
35k6
40k6
40k6
45k6
45k6
50k6
50k6

M12/28
M12/28
M16/36
M16/36
M16/36
M16/36
M16/36
M16/36

Fan
Key

X2
8
10
14
14
14
14
14
14

Y2
4
5
5.5
5.5
5.5
5.5
5.5
5.5

Z2
7
8
9
9
9
9
9
9

L2
70
70
95
95
95
95
95
95

FA

FB

FC

FD

125
135
150
150
170
170
190
190

125
140
140
140
160
160
160
160

50
50
80
80
80
80
80
80

30
30
52
52
52
52
52
52

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions shown in these drawings.

C - 88

DP2

DP1

DP2

Wt.
kg

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

95
140
205
225
305
365
435
495

Oil
Qty.
L
7
11
14
19
24
30
31
45
Unit: mm

4. Refer to the page D -26 for the dimension of optional parts.



DIMENSIONS Right Angle Shaft Double Reduction Upright Mounting

9015 9055

V5

V4

V3

V2
Z1

Y1

V1

V1

W1/Depth

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

U1

T1

Double
Reduction

TU1

Refer to the page D-18 for details.

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

T4

Right Angle

Refer to the page D-18 for details.

Solid Shaft

9015
9025
9030
9035
9040
9045
9050
9055

U4

T2

9015
9055

X1

W1

Size

TU4

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
65
75
85
90
105
105
115

55
65
75
85
90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature
R 2 9015
9025
9030
9035
9040
9045
9050
9055

LL

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P W A

LR

LB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB

(blank) : Without Fan

F : With Fan
(blank) :Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

6.3

7.1

10

14

16

18

9015

9025

9030

9035
9040

9045
9050
9055

11.2 12.5

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 89

DIMENSIONS Right Angle Shaft Double Reduction Upright Mounting

FA

DP1

FA

O
P

FC
FD

FB

Z2

Y2

X2

9060 9085

W2

High Speed Shaft

With Fan

Refer to the page D-20 for details.

4- J
K

R
L2

Y
L

H
L

Dimension Selection
Tables
Tables

Speed
Reducer

E1
F

Size

9060 865 299

9065 911 338
9070 965 336
9075 1018 383
9080 1080 378
9085 1136 422

E1

725
771
825
878
940
996

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

577
647
647
717
717
797

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

885
970
1020
1120
1155
1255

310
310
350
350
380
380

380
380
430
430
460
460

615
700
700
800
835
935

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

140
140
140
140
140
140

60m6
60m6
65m6
65m6
75m6
75m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

Fan
Key

X2
18
18
18
18
20
20

Y2
7
7
7
7
7.5
7.5

Z2
11
11
11
11
12
12

L2
125
125
125
125
125
125

FA

FB

FC

FD

220
220
245
245
270
270

160
160
200
200
225
225

105
105
105
105
105
105

65
65
65
65
60
60

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

600
725
920
1170
1300
1560

44
56
65
87
90
126

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-14 for dimensions shown in these drawings.

C - 90

4. Refer to the page D -29 for the dimension of optional parts.

DP2

DIMENSIONS Right Angle Shaft Double Reduction Upright Mounting

9060 9085

V5

V4

V3

V2

Y1

Z1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

U1

T1

9060
9065
9070
9075
9080
9085

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
11
18
12
20
12
20
13
22
13
22
15
25

Wall
Mount

Solid Shaft
Size

Refer to the page D-18 for details.

Double
Reduction

Refer to the page D-18 for details.

W1

Right Angle

X1

T4

9060
9085

V1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature
R 2 W 9060
9065
9070
9075
9080
9085

LL

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P W D

LR

LB

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB

Size
9060

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9065
9070
9075
9080
9085

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 91

DIMENSIONS Right Angle Shaft Triple Reduction Upright Mounting

FA

FA

9030 9055

DP1
Y3

FD
FC

X2

Z2

Y2

FB

H2

W2

High Speed Shaft

E

With Fan

4- J1

Speed
Reducer

Dimension Selection
Tables
Tables

H1
K3

Y4
L

H
L

4- J2
K3

R
L2

Refer to the page D-21 for details.

Y1

K1

K2

K1

K2

Y2
E1
F

Size

E1

H1

H2

J1

J2

DP2

K1

K2

K3

Y1

Y2

Y3

Y4

9030

656

200

576

110

160

320

348

90

60

28

24

24

85

50

120

590

265

215

200

215

410

9035

687

219

607

129

185

370

398

90

60

28

24

24

100

50

120

640

265

215

250

215

460

9040

716

235

636

120

200

400

430

115

75

30

28

28

100

60

150

685

315

255

260

255

455

9045

755

256

675

141

220

440

470

115

75

30

28

28

120

60

150

745

315

255

300

255

515

9050

808

255

728 138.5 210

420

450 116.5

75

32

28

28

110

60

150

775

345

285

280

285

542

9055

847

286

797

171

490

520

75

32

28

28

135

60

150

845

345

285

350

285

615

245

115

High Speed Shaft

Size

9030
9035
9040
9045
9050
9055

W2/Depth

80
80
80
80
80
80

28k6
28k6
30k6
30k6
35k6
35k6

M10/22
M10/22
M10/22
M10/22
M12/28
M12/28

Fan

Key
X2
8
8
8
8
10
10

Y2
4
4
4
4
5
5

Z2
7
7
7
7
8
8

L2
70
70
70
70
70
70

FA

FB

FC

FD

150
150
170
170
190
190

125
125
125
125
140
140

50
50
50
50
50
50

30
30
30
30
22
22

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
1"
1"
1"
1"

210
230
305
365
445
505

16
21
29
36
35
46

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions shown in these drawings.

C - 92

4. Refer to the page D -26 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Triple Reduction Upright Mounting

9030 9055

TU4
U4

V5

V3

V2

Y1

Z1

T1

U1

V1

330
330
349
391
411
411

160
160
179
181
201
201

170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
22
25
25
28
28
32

L1
150
150
150
190
190
185

9030
9035
9040
9045
9050
9055

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
9
14
9
14
9
14
10
16
10
16
11
18

Solid Shaft
Size

Refer to the page D-18 for details.

Triple
Reduction

Refer to the page D-18 for details.

W1

Right Angle

X1

T4

V4

T2

9030
9055

V1

U2

T1

TU2

U1
L1

TU1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

393
403
448
463
503
528

233
243
268
283
303
323

160
160
180
180
200
205

83
88
98
108
108
123

80
85
95
105
105
120

330
330
360
370
410
410

165
165
180
185
205
205

165
165
180
185
205
205

75
85
90
105
105
115

75
85
90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P W A

LR

R 3 9030
9035
9040
9045
9050
9055

LL

LB

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB

Size
9030

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9035
9040
9045
9050
9055

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 93

DIMENSIONS Right Angle Shaft Triple Reduction Upright Mounting

FA

FA

9060 9085

DP1

FC
FD

O
P

X2

Z2

Y2

FB

W2

High Speed Shaft

H
E

With Fan

E1
F

DP2

Size

9060 939 299 829 151

9065 985 338 875 190
9070 1027 336 917 163
9075 1080 383 970 210
9080 1176 378 1036 205
9085 1232 422 1092 249

E1

265
300
300
335
335
375

530
600
600
670
670
750

577
647
647
717
717
797

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

885
970
1020
1120
1155
1255

310
310
350
350
380
380

380
380
430
430
460
460

131
131
138
138
165
165

615
700
700
800
835
935

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

660
785
940
1190
1350
1610

56
65
83
100
115
144

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

110
110
110
110
140
140

45k6
45k6
50k6
50k6
60m6
60m6

M16/36
M16/36
M16/36
M16/36
M20/42
M20/42

Fan
Key

X2
14
14
14
14
18
18

Y2
5.5
5.5
5.5
5.5
7
7

Z2
9
9
9
9
11
11

L2
95
95
95
95
125
125

Speed
Reducer

Dimension Selection
Tables
Tables

Y
L

4- J
K

R
L2

Refer to the page D-21 for details.

FA

FB

FC

FD

220
220
245
245
270
270

160
160
160
160
160
160

80
80
80
80
105
105

52
52
52
52
65
65

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-14 for dimensions shown in these drawings.

C - 94

4. Refer to the page D -29 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Triple Reduction Upright Mounting

9060 9085

V5

V4

V3

V2

Y1

Z1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

U1

T1

9060
9065
9070
9075
9080
9085

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
11
18
12
20
12
20
13
22
13
22
15
25

Wall
Mount

Solid Shaft
Size

Refer to the page D-18 for details.

Triple
Reduction

Refer to the page D-18 for details.

W1

Right Angle

X1

T4

9060
9085

V1

U4

T2

TU4

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

Nomenclature
Shaft
Arrangement

Size

P W D

Low Speed
Shaft
Type Fan

R 3 W 9060
9065
9070
9075
9080
9085

LL

LB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB

(blank) : Without Fan

F : With Fan

Size
9060

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075
9080
9085

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 95

DIMENSIONS Right Angle Shaft Quadruple Reduction Upright Mounting

9040 9055

Y3

Z2

Y2

DP1
X2

W2

H2
E

R
L2

High Speed Shaft

H1
K3

Y4
L

4- J2
K3

H
L

4- J1

Dimension Selection
Tables
Tables

Speed
Reducer

K1

K1

Y1
K2

Y2
E1
F

K2
P

DP2

Size

E1

H1

H2

J1

J2

K1

K2

K3

Y1

Y2

Y3

Y4

9040

790

235

710

120

200

400

430

115

75

30

28

28

100

60

150

759

315

255

260

255

529

9045

829

256

749

141

220

440

470

115

75

30

28

28

120

60

150

819

315

255

300

255

589

9050

859

255

779 138.5 210

420

450 116.5

75

32

28

28

110

60

150

848

345

285

280

285

615

9055

898

286

818

171

490

520

75

32

28

28

135

60

150

918

345

285

350

285

688

245

115

High Speed Shaft

Size
9040
9045
9050
9055

W2/Depth

80
80
80
80

28k6
28k6
28k6
28k6

M10/22
M10/22
M10/22
M10/22

Key
X2
8
8
8
8

Y2
4
4
4
4

Z2
7
7
7
7

L2
70
70
70
70

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"

1"
1"
1"
1"

325
395
460
520

35
43
46
59

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-13 for dimensions shown in these drawings.

C - 96

4. Refer to the page D -26 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Quadruple Reduction Upright Mounting

9040 9055

Z1

V5

V4

V3

V2

9040
9045
9050
9055

TU1

T1

U1

V1

349
391
411
411

179
181
201
201

170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M24/50
M24/50
M24/50
M24/50

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
9
14
10
16
10
16
11
18

X1
25
28
28
32

L1
150
190
190
185

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

448
463
503
528

268
283
303
323

180
180
200
205

98
108
108
123

95
105
105
120

360
370
410
410

180
185
205
205

180
185
205
205

90
105
105
115

90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature
Shaft
Arrangement

Size

P W A

R 4 9040
9045
9050
9055

LR

Low Speed
Shaft
Type

LL

LB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9040

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9045
9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 97

Solid Shaft
Size

Refer to the page D-18 for details.

Refer to the page D-18 for details.

W1

Right Angle Quadruple

Reduction

Y1

X1

T4

9040
9055

V1

U4

T2

TU4

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

DIMENSIONS Right Angle Shaft Quadruple Reduction Upright Mounting

9060 9085

O
P

Y2

X2

Z2

DP1

W2

H
E

Y
L

4- J

L2

High Speed Shaft

Dimension Selection
Tables
Tables

Speed
Reducer

DP2

E1
F

Size

E1

9060
9065
9070
9075
9080
9085

950
996
1080
1133
1250
1306

299
338
336
383
378
422

870
916
1000
1053
1140
1196

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

577
647
647
717
717
797

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

970
1055
1115
1215
1275
1375

310
310
350
350
380
380

380
380
430
430
460
460

79
79
70
70
101
101

700
785
795
895
955
1055

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

W2/Depth

80
80
80
80
110
110

30k6
30k6
35k6
35k6
45k6
45k6

M10/22
M10/22
M12/28
M12/28
M16/36
M16/36

Key
X2
8
8
10
10
14
14

Y2
4
4
5
5
5.5
5.5

Z2
7
7
8
8
9
9

L2
70
70
70
70
95
95

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

670
825
960
1180
1390
1650

68
85
107
122
128
174

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-15 for dimensions shown in these drawings.

C - 98

4. Refer to the page D -29 for the dimension of optional parts.

DIMENSIONS Right Angle Shaft Quadruple Reduction Upright Mounting

9060 9085

V5

V4

V3

V2

Y1

Z1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125 123
145 143
145 143
150 148
165 163
175 173
Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

Nomenclature
Shaft
Arrangement

Size

P W D

Low Speed
Shaft
Type

R 4 W 9060
9065
9070
9075
9080
9085

LL

LB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9060

9065
9070

9075
9080

9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 99

T1

Hollow Shaft (Key Type)

Wall
Mount

9060
9065
9070
9075
9080
9085

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
11
18
12
20
12
20
13
22
13
22
15
25

Solid Shaft
Size

Refer to the page D-18 for details.

Refer to the page D-18 for details.

W1

Right Angle Quadruple

Reduction

X1

T4

9060
9085

V1

U4

T2

TU4

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

C - 100

<Reducer: Parallel Shaft Horizontal Mounting>

<Reducer: Parallel Shaft Upright Mounting>

<Reducer: Parallel Shaft Vertical Mounting>

Reducer: Parallel shaft

Selection Tables
Allowable Loads
Dimension Sheets

C- 102
C- 132
C- 136

C - 101

SELECTION Parallel Shaft Double Reduction

Nominal Reduction Ratio 6.3 8

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
286
1500
238
6.3
1200
190
1000
159
900
143
750
119
Exact Reduction Ratio
1800
254
1500
211
1200
169
7.1
1000
141
900
127
750
106
Exact Reduction Ratio
1800
225
1500
188
8
1200
150
1000
125
900
113
750
94
Horizontal
Dimension
Vertical
Tables
Upright

6.257

76
64
51
43
39
32
7.237

62
52
42
35
31
26.5
7.889

6.193

122
102
82
68
62
51
7.067

100
83
67
56
50
42
7.616

6.314

6.049

6.470

6.188

6.246

6.429

6.609

179
149
120
100
91
76

257
223
187
162
148
125

350
305
256
222
203
174

603
530
448
388
355
302

900
792
677
588
538
462

1430
1250
1050
884
798
668

1950
1710
1450
1240
1120
943

6.806

6.903

7.366

7.210

6.998

7.090

7.190

161
135
108
90
82
68

241
201
162
136
122
102

349
293
235
197
178
149

559
469
377
316
285
238

900
757
610
511
461
386

1350
1130
914
766
691
579

1830
1610
1320
1100
999
836

8.118

7.869

7.778

7.691

7.956

8.062

7.875

7.759

8.033

7.733

8.167

61
99
140
187
219
257
311
350
517
603
781
900 1230
51
83
117
156
190
223
271
305
455
530
687
792 1030
41
67
94
126
154
187
227
256
378
448
571
677
836
34
56
78
105
129
162
195
222
317
388
478
588
700
31
50
71
95
116
148
176
203
286
355
432
538
632
25.9
42
59
79
97
127
147
174
239
304
361
462
529
C-136 C-136 C-136 C-136 C-136 C-136 C-136 C-136 C-138 C-138 C-138 C-138 C-138
C-162 C-162 C-162 C-162 C-162 C-162 C-162 C-162 C-164 C-164 C-164 C-164 C-164
C-180 C-180 C-180 C-180 C-180 C-180 C-180 C-180 C-182 C-182 C-182 C-182 C-182

7.835

8.111

1430
1250
1070
932
841
704
C-138
C-164
C-182

1660
1450
1200
1020
923
773
C-140
C-166

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans

40
51
57
73
88
108
103
127
147
174
1800

1
111
132
143
193
216
265
250
308
415
491
Double
39
50
58
75
89
110
106
131
151
180
192
238
232
284 360
Reduction 1500
1
97
117
130
176
195
240
228
282
378
452
446
500
492
679 986
Horizontal
38
49
58
75
88
110
106
131
151
182
196
245
240
296 370
1200
Type
1
83
101
115
156
171
213
202
251
337
405
404
456
452
629 901
36
47
56
74
86
108
104
130
149
180
195
245
241
299 371
1000
1
71
86
100
136
148
185
176
220
294
355
356
405
402
562 799
6.3
35
46
55
73
85
107
103
128
147
178
193
243
240
298 369

900
1
66
81
94
128
139
176
166
208
277
336
337
385
382
537 761
8
33
44
53
70
81
103
99
124
142
173
188
239
235
293 362
750
1
57
70
82
113
122
154
146
183
245
298
300
343
342
481 680

Double
Reduction
Vertical
Type

6.3

Double
Reduction
Upright
Type

6.3

1800

39

49

54

69

84

102

98

120

135

158

163

200

182

229

220

1500

38

49

56

72

86

106

102

125

142

168

182

219

210

258

277

1200

37

48

56

73

86

107

103

128

145

174

194

231

231

278

317

1000

36

46

55

72

85

106

102

127

144

174

195

235

239

285

330

900

35

45

54

71

83

105

101

126

143

173

193

235

240

286

334

750

33

43

52

69

80

101

98

122

139

169

188

232

235

284

336

1800

1
1
1
1
1
1

32
89
31
78
30
66
29
56
28
53
26
45

40
106
40
94
39
81
38
69
37
65
35
56

45
115
46
104
46
92
45
80
44
75
43
66

59
154
60
141
60
125
59
109
58
103
56
90

70
173
71
156
71
137
69
118
68
111
65
97

86
212
88
192
88
170
86
148
86
141
82
123

82
200
85
182
85
162
83
141
82
133
79
117

102
246
105
225
105
201
104
176
102
166
99
147

118
332
121
303
121
269
119
235
117
222
114
196

139
393
144
361
146
324
144
284
142
269
138
238

147
383
154
357
157
323
156
285
154
270
151
240

180
425
190
400
196
365
196
324
195
308
191
275

171
408
186
394
192
361
193
321
192
306
188
273

211
567
227
543
237
503
239
450
238
429
235
385

1500
1200
1000
900
750

C - 102

SELECTION Parallel Shaft Double Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
6.460

6.203

2970
2610
2160
1810
1630
1370

3900
3440
2940
2550
2340
2000

7.333

6.933

7.071

7.118

7.030

1950
1710
1450
1240
1140
978

2790
2380
1920
1610
1450
1220

2970
2610
2230
1930
1760
1480

3460
3050
2600
2240
2020
1690

3910
3440
2940
2550
2340
2000

8.222

7.672

8.059

8.042

7.956

1830
1610
1360
1170
1060
891
C-140
C-166

2480 2790 3200 3460

2120 2450 2820 3050
1710 2080 2350 2610
1430 1740 2020 2260
1290 1570 1850 2070
1080 1310 1580 1780
C-140 C-140 C-140 C-140
C-166 C-166 C-166 C-166

Nominal Reduction Ratio 6.3 8

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

286
1800
238
1500
6.3
190
1200
159
1000
143
900
119
750
Exact Reduction Ratio
254
1800
211
1500
7.1
169
1200
141
1000
127
900
106
750
Exact Reduction Ratio
225
1800
188
1500
8
150
1200
125
1000
113
900
94
750
Horizontal
Dimension
Vertical
Tables
Upright

401 454 509 567

1056 1148 1241 1336
415 471 533 610
970 1056 1153 1277
417 474 539 621
864 942 1034 1152
415 472 538 621
823 898 988 1103
408 465 532 616
737 805 889 995

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft speed
is not shown in the table, nd it
by the interpolation method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

5.
750
Shown in the table are the ratings
for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9115 9118 9121 9126 9128 9131 9136
r/min
Ratio
Fans

Without Fan With Fan

1800
1.00
20
1.00

1
Double
633
0.85
30
0.87
1500 Reduction
1443
1
Horizontal
0.70
673
40
0.73
1200
Type
1362
1
0.55
50
0.60
687
1000
1231
1
6.3
689

900
1182
1
8
0QVGU
685
750
1069
1
Size of Reducer

9095 9100 9105 9110

0QVGU

256

221

280

188

258

1800

311

311

367

339

407

1500 Reduction

351

382

432

452

515

1200

369

412

463

507

567

1000

375

419

474

529

587

900

378

425

484

549

608

750

1
1
1
1
1
1

1800

Double
Vertical
Type

6.3

Double

1500 Reduction
1200
1000
900

Upright
Type

6.3

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.
4.
For marked, please consult
us.

750

C - 103

SELECTION Parallel Shaft Double Reduction

Nominal Reduction Ratio 9 11.2

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
200
1500
167
9
1200
133
1000
111
900
100
750
83
Exact Reduction Ratio
1800
180
1500
150
10
1200
120
1000
100
900
90
750
75
Exact Reduction Ratio
1800
161
1500
134
11.2
1200
107
1000
89
900
80
750
67
Horizontal
Dimension
Vertical
Tables
Upright

9.125

49
41
33
28.0
25.3
21.1
10.143

47
40
32
26.9
24.2
20.2

8.690

81
68
55
46
41
34
9.722

78
65
52
44
39
33

8.750

8.556

8.875

8.750

9.057

9.058

9.176

8.874

9.000

126
105
85
71
64
53

170
142
114
96
86
72

188
158
127
106
95
80

253
212
170
142
128
107

286
239
192
161
145
121

350
305
246
206
186
155

443
371
298
250
225
188

583
489
393
329
297
249

708
593
477
400
361
302

9.944

10.118

9.528

9.889

10.156

9.914

9.750

9.875

9.665

115
96
77
64
58
48

146
122
98
82
74
62

188
158
127
106
95
80

219
190
159
136
123
103

259
226
184
154
139
116

311
271
227
197
180
155

452
382
307
257
232
194

517
455
384
333
304
255

689
593
477
399
360
301

8.677

9.007

8.603

8.824

900 1070 1410 1560

792
900 1180 1340
647
725
956 1080
542
607
801 907
489
548
723 818
409
458
605 685
9.945

9.905

9.953

10.342

781 1020 1230 1380

687
861 1080 1180
588
693
881 964
505
580
738 807
456
524
666 728
381
438
558 610

11.732 11.094 10.719 11.000 10.872 11.250 11.563 11.138 11.361 11.294 10.829 11.160 10.924 10.929 11.250

39
64
103
133
154
198
225
299
360
462
592
751
891
32
53
86
111
129
166
188
250
301
387
495
629
746
26.2
43
69
89
104
133
151
201
242
311
399
507
600
21.9
36
58
75
87
111
127
168
202
260
334
424
503
19.7
32
52
67
78
100
114
152
183
235
301
383
453
16.5 27.3
43
56
65
84
95
127
153
196
252
320
379
C-136 C-136 C-136 C-136 C-136 C-136 C-136 C-136 C-138 C-138 C-138 C-138 C-138
C-162 C-162 C-162 C-162 C-162 C-162 C-162 C-162 C-164 C-164 C-164 C-164 C-164
C-180 C-180 C-180 C-180 C-180 C-180 C-180 C-180 C-182 C-182 C-182 C-182 C-182

1120
941
758
635
573
479
C-138
C-164
C-182

1260
1060
855
716
646
540
C-140
C-166

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans

35
46
53
67
81
100
99
124
141
171
180
1800

1
97
119
134
175
199
245
240
300
397
482
469
Double
34
45
53
67
81
100
100
126
143
174
185
229
226
279 344
Reduction 1500
1
84
104
120
158
177
218
215
271
358
437
431
481
479
669 942
Horizontal
32
43
52
66
79
99
98
125
142
173
187
231
230
286 347
1200
Type
1
71
89
105
138
154
192
188
239
315
385
385
431
433
607 844
31
41
51
65
77
96
96
122
139
170
185
229
229
285 344
1000
1
60
76
90
119
132
165
163
207
273
336
337
378
382
536 741
9
30
40
50
63
75
94
94
120
136
167
182
226
227
283 340

900
1
56
70
85
112
124
154
153
195
257
316
319
357
362
509 702
11.2
28
38
48
61
72
90
90
116
131
162
177
220
222
276 331
750
1
48
61
74
98
108
135
133
171
226
279
282
316
322
453 622

Double
Reduction
Vertical
Type

11.2

Double
Reduction
Upright
Type

11.2

1800

35

46

53

64

81

96

98

118

139

158

180

203

216

238

241

1500

34

45

53

65

81

97

100

121

143

164

185

221

226

266

284

1200

32

43

52

65

79

97

98

122

142

166

187

231

230

285

306

1000

31

41

51

63

77

94

96

120

139

165

185

229

229

285

313

900

30

40

50

62

75

93

94

118

136

163

182

226

227

283

314

750

28

38

48

60

72

89

90

115

131

159

177

220

222

276

311

1800

1
1
1
1
1
1

28
78
27
68
26
57
25
48
24
45
22
38

36
96
36
84
34
71
33
61
32
56
30
48

42
107
43
96
42
84
41
72
40
68
38
59

53
140
54
126
53
110
52
95
51
89
49
78

65
159
65
141
64
123
62
106
60
99
58
86

80
196
80
174
79
153
77
132
75
123
72
108

79
192
80
172
79
150
77
130
75
122
72
107

99
240
101
217
100
191
98
166
96
156
93
137

113
317
114
287
113
252
111
219
109
206
105
181

137
386
139
349
138
308
136
268
134
252
130
223

144
375
148
345
149
308
148
270
146
255
142
225

177
419
183
385
185
345
183
302
181
286
176
253

173
412
181
383
184
346
183
305
182
290
177
257

213
573
224
535
228
485
228
429
226
407
221
362

1500
1200
1000
900
750

C - 104

SELECTION Parallel Shaft Double Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
9.000

8.824

9.000

9.248

9.134

1660
1450
1200
1030
948
813

2250
1890
1520
1270
1150
965

2480
2190
1820
1550
1390
1170

2840
2500
2070
1740
1570
1310

3200
2820
2350
2020
1850
1580

9.765

9.984

9.765

9.774

10.449

1560
1370
1130
966
872
730

2090
1760
1410
1180
1070
897

2330
2040
1640
1380
1240
1040

2780
2400
1990
1700
1560
1310

2850
2500
2090
1790
1640
1390

11.475

1380
1180
981
842
770
651
C-140
C-166

10.714

10.929 11.216 11.078

1860 2150 2470 2780

1560 1850 2130 2400
1260 1530 1720 1990
1050 1280 1440 1710
954 1150 1300 1560
799 970 1090 1340
C-140 C-140 C-140 C-140
C-166 C-166 C-166 C-166

Nominal Reduction Ratio 9 11.2

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

200
1800
167
1500
9
133
1200
111
1000
100
900
83
750
Exact Reduction Ratio
180
1800
150
1500
10
120
1200
100
1000
90
900
75
750
Exact Reduction Ratio
161
1800
134
1500
11.2
107
1200
89
1000
80
900
67
750
Horizontal
Dimension
Vertical
Tables
Upright

374 443 496 544

986 1119 1210 1282
376 452 504 563
879 1015 1090 1178
371 451 500 565
770 897 960 1049
367 448 496 563
728 852 910 1000
357 438 484 554
644 759 809 896

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft speed
is not shown in the table, nd it
by the interpolation method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

5.
750
Shown in the table are the ratings
for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9115 9118 9121 9126 9128 9131 9136
r/min
Ratio
Fans

Without Fan With Fan

1800
1.00
20
1.00

1
Double
619
0.85
30
0.87
1500 Reduction
1411
1
Horizontal
0.70
644
40
0.73
1200
Type
1302
1
0.55
50
0.60
646
1000
1157
1
9
642

900
1102
1
11.2
0QVGU
631
750
985
1
Size of Reducer

9095 9100 9105 9110

0QVGU

274

279

326

276

338

1800

315

344

388

379

441

1500 Reduction

335

384

434

456

518

1200

340

400

448

485

554

1000

340

404

451

495

566

900

337

405

451

502

575

750

1
1
1
1
1
1

1800

Double
Vertical
Type

11.2

Double

1500 Reduction
1200
1000
900

Upright
Type

11.2

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.
4.
For marked, please consult
us.

750

C - 105

SELECTION Parallel Shaft Double Reduction

Nominal Reduction Ratio 12.5 16

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
144
1500
120
12.5
1200
96
1000
80
900
72
750
60
Exact Reduction Ratio
1800
129
1500
107
14
1200
86
1000
71
900
64
750
54
Exact Reduction Ratio
1800
113
1500
94
16
1200
75
1000
63
900
56
750
47
Horizontal
Dimension
Vertical
Tables
Upright

12.710 12.407 12.785 12.394 12.485 12.114 12.594 12.656 12.206 12.226 12.600 11.966 12.762 12.071 12.978

38
32
25.8
21.5
19.4
16.2

61
51
41
34
31
26.2

89
75
60
50
45
38

120
100
80
67
61
51

145
121
97
81
73
61

191
165
133
111
101
84

222
185
149
125
112
94

259
226
190
164
148
124

366
307
246
206
186
155

452
398
328
274
247
207

547
458
368
308
278
232

689
607
504
422
380
318

804 1060 1110

673
908 959
542
731 773
453
612 647
409
552 584
342
462 488

14.701 14.158 13.781 13.475 14.247 13.781 14.337 14.219 14.224 13.983 14.118 13.428 14.076 13.255 14.118

31
26.1
21.0
17.5
15.8
13.2

50
42
34
28.5
25.7
21.4

81
67
54
45
41
34

109
91
73
61
55
46

118
99
79
66
60
50

162
136
109
91
82
69

183
153
123
102
92
77

235
197
158
132
119
100

289
242
194
162
146
122

375
314
252
211
190
159

457
383
308
257
232
194

628
526
423
354
319
267

696
583
469
392
354
296

931 1010
780 851
628 685
526 573
474 517
397 433

15.778 15.340 15.997 15.935 15.556 15.874 16.504 15.694 15.996 15.306 15.750 15.600 15.556 15.554 16.222

31
50
72
94
116
152
170
237
281
389
440
565
663
846 920
25.9
42
60
78
97
127
142
198
235
327
368
484
555
709 773
20.8
33
48
63
78
102
114
159
189
263
296
389
446
571 622
17.4 28.2
40
52
65
85
95
133
158
220
248
325
373
478 520
15.7 25.4
36
47
59
77
86
120
142
198
223
293
337
431 469
13.1 21.2
30
39
49
64
72
100
119
166
187
245
281
360 392
C-136 C-136 C-136 C-136 C-136 C-136 C-136 C-136 C-138 C-138 C-138 C-138 C-138 C-138 C-140
C-162 C-162 C-162 C-162 C-162 C-162 C-162 C-162 C-164 C-164 C-164 C-164 C-164 C-164 C-166
C-180 C-180 C-180 C-180 C-180 C-180 C-180 C-180 C-182 C-182 C-182 C-182 C-182 C-182

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
30
42
51
63
74
95
89
116
125
159
163
210
206
261 311
1800
1
85
111
130
167
182
233
214
281
353
448
425
495
489
701 959
Double
29
41
50
63
73
94
87
115
124
159
164
211
209
265 315
Reduction 1500
1
72
95
113
148
159
205
188
248
311
399
380
444
442
635 862
Horizontal
27
39
48
62
70
91
85
112
121
155
161
209
208
264 311
1200
Type
1
60
80
96
129
135
176
162
214
268
345
332
389
390
561 757
26
37
46
60
67
88
81
108
116
150
157
204
204
259 304
1000
1
50
67
81
110
115
151
138
183
230
296
286
336
339
488 656
12.5
25
36
44
59
65
85
79
106
113
147
154
200
200
255 299

900
1
46
62
75
103
107
140
128
171
214
278
269
316
319
460 617
16
23
33
42
56
62
81
75
101
108
141
147
192
193
247 288
750
1
39
53
64
90
92
121
111
149
186
243
235
277
280
404 542

Double
Reduction
Vertical
Type

12.5

16

Double
Reduction
Upright
Type

12.5

16

1800

31

43

52

63

75

95

90

116

130

159

170

210

216

261

258

1500

29

41

51

63

74

95

88

115

127

159

169

211

220

265

274

1200

27

39

48

62

71

92

85

112

123

155

165

209

216

264

283

1000

26

37

46

60

67

88

82

108

118

150

160

204

210

259

283

900

25

36

45

59

65

86

80

106

115

147

156

200

205

255

281

750

23

33

42

56

62

81

76

101

109

141

149

192

197

247

274

1800

1
1
1
1
1
1

24
68
23
58
22
48
20
40
20
37
18
31

34
89
33
76
31
64
29
54
28
50
27
42

41
104
40
90
38
77
37
65
35
60
33
51

51
133
51
119
50
103
48
88
47
83
45
72

59
145
58
127
56
108
54
92
52
85
49
74

76
186
75
164
73
141
70
121
68
112
65
97

71
171
70
151
68
129
65
110
63
103
60
89

93
225
92
198
90
171
87
147
85
137
81
119

100
283
99
249
96
215
93
184
91
171
86
149

127
359
127
319
124
276
120
237
118
222
113
194

130
340
131
304
129
266
125
229
123
215
118
188

168
396
169
355
167
311
163
269
160
253
154
221

164
391
167
354
166
312
163
271
160
255
154
224

209
561
212
508
211
449
207
390
204
368
197
324

1500
1200
1000
900
750

C - 106

SELECTION Parallel Shaft Double Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
12.450

12.950 11.857 12.434 12.672

1290 1630 2020 2240 2470

1110 1360 1690 1920 2130
910 1100 1360 1590 1770
762 922 1140 1360 1520
688 832 1030 1240 1370
576 696 864 1040 1150
14.400 13.897 14.175 14.268 14.092

1110 1450 1700 1990 2240

958 1210 1460 1690 1920
794 980 1190 1360 1590
681 821 996 1140 1370
623 740 899 1030 1250
521 619 752 862 1070
15.624 15.961 15.379 15.325 16.121

1050
902
730
611
551
461
C-140
C-166

1330 1570 1870 2000

1110 1310 1600 1710
898 1060 1330 1420
752 887 1120 1200
678 800 1010 1080
567 670 850 911
C-140 C-140 C-140 C-140
C-166 C-166 C-166 C-166

Nominal Reduction Ratio 12.5 16

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

144
1800
120
1500
12.5
96
1200
80
1000
72
900
60
750
Exact Reduction Ratio
129
1800
107
1500
14
86
1200
71
1000
64
900
54
750
Exact Reduction Ratio
113
1800
94
1500
16
75
1200
63
1000
56
900
47
750
Horizontal
Dimension
Vertical
Tables
Upright

359 399 462 505

1064 1133 1265 1338
364 405 471 522
959 1024 1149 1230
362 404 471 527
847 905 1020 1103
355 396 464 522
736 788 890 968
350 390 458 516
694 743 841 916
338 378 444 502
611 654 743 812
315

344

343

373

1800

316

342

392

406

452

1500 Reduction

328

359

417

449

504

1200

329

362

423

463

521

1000

328

361

423

466

525

900

Double

356

418

464

2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

289

322

1.
For marked values, the forced
oil lubrication is required at
continuous operation.

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9115 9118 9121 9126 9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

565
1800
1.00
20
1.00
1446
1
Double
585
0.85
30
0.87
1500 Reduction
1332
1
Horizontal
0.70
592
40
0.73
1200
Type
1197
1
0.55
50
0.60
588
1000
1053
1
12.5
582

900
998
1
16
0QVGU
568
750
887
1
Size of Reducer

9095 9100 9105 9110

0QVGU

525

750

1
1
1
1
1
1

1800

Vertical
Type

12.5

16

Double

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

12.5

16

750

C - 107

SELECTION Parallel Shaft Double Reduction

Nominal Reduction Ratio 18 22.4

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
100
1500
83
18
1200
67
1000
56
900
50
750
42
Exact Reduction Ratio
1800
90
1500
75
20
1200
60
1000
50
900
45
750
38
Exact Reduction Ratio
1800
80
1500
67
22.4
1200
54
1000
45
900
40
750
33
Horizontal
Dimension
Vertical
Tables
Upright

18.250 17.503 17.243 17.325 17.750 18.059 18.789 17.631 18.640 17.506 17.647 17.506 17.157 17.078 17.647

25.3
21.1
17.0
14.2
12.8
10.7

*
*
*
*
*
*

41
34
27.6
23.1
20.8
17.4

*
*
*
*
*
*

65
54
43
36
32
27.5

*
*
*
*
*
*

85
71
57
48
43
36

95
80
64
53
48
40

124
104
84
70
63
52

140
117
94
78
71
59

191
159
128
107
96
81

222
185
149
124
112
94

301
252
203
169
153
128

368
308
247
207
186
156

485
406
326
273
246
206

19.938

19.778

20.566

20.059

19.500

75
63
50
42
38
31

123
103
82
69
62
52

182
152
122
102
92
77

300
251
202
169
152
127

465
389
313
261
236
197

*
*
*
*
*
*

21.676

*
*
*
*
*
*

22.500

*
*
*
*
*
*

23.105

*
*
*
*
*
*

22.941

574
481
386
323
291
244

728
610
490
410
370
310

818
685
551
461
416
348

18.958

*
*
*
*
*
*

21.882

699
585
470
393
355
297

*
*
*
*
*
*

20.817

68
100
146
231
390
601
*
*
*
*
*
*
*
*
*
57
84
122
193
326
503
*
*
*
*
*
*
*
*
*
46
67
98
155
262
404
*
*
*
*
*
*
*
*
*
38
56
82
130
219
338
*
*
*
*
*
*
*
*
*
34
51
74
117
198
305
*
*
*
*
*
*
*
*
*
29.1
42
62
98
165
255
*
*
*
*
*
*
*
*
*
C-136 C-136 C-136 C-136 C-136 C-136 C-136 C-136 C-138 C-138 C-138 C-138 C-138 C-138 C-140
C-162 C-162 C-162 C-162 C-162 C-162 C-162 C-162 C-164 C-164 C-164 C-164 C-164 C-164 C-166
C-180 C-180 C-180 C-180 C-180 C-180 C-180 C-180 C-182 C-182 C-182 C-182 C-182 C-182

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
29
41
50
60
66
83
88
106
127
153
166
194
209
247 309
1800
1
81
106
127
156
162
203
213
255
358
431
433
459
498
664 950
Double
28
39
49
58
65
81
87
104
126
150
167
194
213
249 311
Reduction 1500
1
69
91
110
135
142
177
187
223
316
376
387
407
450
595 854
Horizontal
26
37
47
55
63
78
84
100
122
145
164
189
211
245 308
1200
Type
1
58
77
93
114
121
151
161
190
272
323
338
353
397
521 750
25
35
45
52
60
74
81
96
118
140
160
184
207
239 301
1000
1
48
65
79
96
103
127
137
162
233
276
291
303
345
450 650
18
24
34
43
51
59
72
79
93
115
136
156
180
204
235 296

900
1
44
60
73
89
97
118
128
151
217
257
273
284
325
423 611
22.4
22
32
41
48
56
68
75
88
110
129
150
172
196
226 285
750
1
37
51
63
76
84
102
110
130
188
222
239
247
285
370 536

Double
Reduction
Vertical
Type

18

22.4

Double
Reduction
Upright
Type

18

22.4

1800

29

41

51

60

62

85

90

107

131

149

173

201

224

262

256

1500

28

40

49

58

62

82

88

105

129

146

172

199

224

260

272

1200

26

37

47

55

61

79

85

100

124

140

168

193

219

253

280

1000

25

35

45

53

59

75

82

96

120

135

162

186

213

246

280

900

24

34

43

51

57

73

79

93

116

131

159

182

209

240

278

750

22

32

41

48

55

68

75

88

111

124

152

174

200

230

272

1800

1
1
1
1
1
1

23
65
22
55
21
46
20
38
19
35
18
30

32
85
31
73
30
61
28
52
27
48
25
41

40
102
39
88
37
75
36
63
35
59
32
50

48
125
46
108
44
91
42
77
40
71
38
61

53
130
52
114
50
97
48
83
47
77
45
67

66
163
65
141
62
121
59
102
58
95
54
81

71
171
70
150
67
129
65
110
63
102
60
88

84
204
83
178
80
152
76
129
74
121
70
104

102
287
101
253
98
218
94
186
92
174
88
151

122
345
120
301
116
258
112
221
109
206
103
178

133
346
133
310
131
270
128
233
125
219
120
191

156
367
155
326
152
282
147
243
144
227
138
198

168
399
170
360
169
318
166
276
163
260
157
228

198
532
199
476
196
417
191
360
188
339
181
296

1500
1200
1000
900
750

C - 108

SELECTION Parallel Shaft Double Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
920 1180 1420 1650 1870
789 994 1200 1380 1610
654 799 971 1110 1330
555 669 812 931 1140
501 603 733 840 1040
419 505 613 703 899
867
730
587
491
443
370

*
*
*
*
*
*

18.955

19.869

*
*
*
*
*
*

1280
1070
864
723
652
546

*
*
*
*
*
*

1670
1430
1170
983
887
742

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

100
1800
83
1500
18
67
1200
56
1000
50
900
42
750
Exact Reduction Ratio
90
1800
75
1500
20
60
1200
50
1000
45
900
38
750
Exact Reduction Ratio
80
1800
67
1500
22.4
54
1200
45
1000
40
900
33
750
Horizontal
Dimension
Vertical
Tables
Upright

18.000 17.128 17.471 17.585 17.368

19.529

Nominal Reduction Ratio 18 22.4

C-140 C-140 C-140 C-140 C-140

C-166 C-166 C-166 C-166 C-166

* marked models are triple reduction units. Refer to C-110 and C-111.

336 402 437 485

995 1141 1198 1285
338 408 441 500
889 1032 1076 1179
332 406 437 504
777 911 946 1056
324 399 428 499
672 793 821 926
318 393 421 493
631 747 773 876
306 380 406 480
553 658 679 776
319

355

349

402

1800

298

346

380

397

447

1500 Reduction

305

362

393

431

478

1200

303

365

395

444

488

1000

300

364

393

446

489

900

Double

358

385

444

2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

284

293

1.
For marked values, the forced
oil lubrication is required at
continuous operation.

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9115 9118 9121 9126 9128 9131 9136
r/min
Ratio
Fans

Without Fan With Fan

537
1800
1.00
20
1.00
1375
1
Double
550
0.85
30
0.87
1500 Reduction
1252
1
Horizontal
0.70
551
40
0.73
1200
Type
1114
1
0.55
50
0.60
543
1000
973
1
18
536

900
920
1
22.4
0QVGU
521
750
813
1
Size of Reducer

9095 9100 9105 9110

0QVGU

485

750

1
1
1
1
1
1

1800

Vertical
Type

18

22.4

Double

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

18

22.4

750

C - 109

SELECTION Parallel Shaft Triple Reduction

Nominal Reduction Ratio 20 25

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
90
1500
75
20
1200
60
1000
50
900
45
750
38
Exact Reduction Ratio
1800
80
1500
67
22.4
1200
54
1000
45
900
40
750
33
Exact Reduction Ratio
1800
72
1500
60
25
1200
48
1000
40
900
36
750
30
Horizontal
Dimension
Vertical
Tables
Upright

19.894

19.681 20.280

26.4
22.1
17.7
14.8
13.3
11.1

39
33
27.8
23.6
21.2
17.7

23.011

22.457 21.860

21.5
18.0
14.4
12.1
10.9
9.1

34
28.8
23.1
19.3
17.4
14.5

61
51
41
34
30
25.8
55
46
37
30
27.9
23.3

*
*
*
*
*
*
*
*
*
*
*
*

19.884

19.590

18.988

20.067

20.054

98
82
66
55
49
41

154
129
103
86
78
65

254
213
171
143
129
107

356
310
250
209
188
157

554
463
372
311
281
235

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

22.689

22.303

22.125

22.484

22.119

80
67
54
45
40
34

127
106
85
71
64
53

201
168
135
112
101
85

310
260
208
174
157
131

480
401
322
269
243
203

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

20.585

*
*
*
*
*
*

758
650
527
441
397
332
22.394

*
*
*
*
*
*

694
581
467
391
352
294

24.696 24.332 25.374 25.277 24.774 25.281 25.673 24.413 24.883 23.810 25.083 24.844 24.444 24.441 25.732

21.4
32
49
64
79
100
118
165
195
261
299
356
456
572 624
17.8 28.2
41
53
66
83
98
138
163
226
250
310
382
488 527
14.3 22.9
32
43
53
67
79
110
131
182
201
260
307
392 423
12.0 19.1 27.5
35
44
55
66
92
109
152
168
220
256
328 354
10.8 17.2 24.8
32
40
50
59
83
99
137
151
199
231
296 319
9.0 14.4 20.7 27.0
33
41
50
69
82
114
126
166
193
247 267
C-142 C-142 C-142 C-142 C-142 C-142 C-142 C-142 C-144 C-144 C-144 C-144 C-144 C-144 C-146
C-168 C-168 C-168 C-168 C-168 C-168 C-168 C-168 C-170 C-170 C-170 C-170 C-170 C-170 C-172
C-184 C-184 C-184 C-184 C-184 C-184 C-184 C-184 C-186 C-186 C-186 C-186 C-186 C-186

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
24
36
42
54
63
77
77
97
107
131
145
179
184
225 235
1800
1
66
93
78
114
155
189
187
234
210
257
269
309
437
605 556
Triple
23
35
42
53
62
76
76
95
106
130
145
178
185
226 238
Reduction 1500
1
58
81
68
99
135
166
164
205
185
227
238
273
391
540 501
Horizontal
22
34
40
51
60
73
74
92
104
126
142
175
183
223 237
1200
Type
1
49
70
58
85
115
141
141
176
160
195
207
237
343
473 443
21
32
38
49
57
70
71
89
101
123
138
170
179
217 233
1000
1
41
59
50
72
98
120
121
151
138
169
179
204
298
409 386
20
20
31
37
47
56
68
70
87
98
120
135
166
176
214 229

900
1
38
55
46
67
91
112
113
141
129
158
168
192
280
385 364
25
19
30
36
45
53
64
67
83
94
115
130
160
170
206 223
750
1
33
48
40
58
79
96
98
122
113
137
147
168
247
338 322

Triple
Reduction
Vertical
Type

20

25

Triple
Reduction
Upright
Type

20

25

1800

22

33

40

51

60

73

73

91

100

122

135

167

168

206

212

1500

22

33

40

50

59

73

73

91

101

123

137

169

173

212

221

1200

21

32

39

49

58

70

71

89

100

122

136

168

174

212

225

1000

21

31

37

47

56

68

69

87

97

119

134

165

172

210

223

900

20

31

37

46

55

66

68

85

96

117

132

162

170

207

222

750

19

29

35

44

52

63

65

81

92

113

127

156

166

201

217

1800

1
1
1
1
1
1

24
66
23
57
22
49
21
41
20
38
19
33

36
93
35
81
34
70
32
59
31
55
30
48

42
78
41
68
40
58
38
50
37
46
35
40

54
113
53
99
51
85
48
72
47
67
45
58

69
168
67
147
65
126
62
107
61
100
58
86

77
189
76
166
73
141
70
120
68
112
64
96

76
185
76
163
73
140
71
120
69
112
66
98

96
231
94
203
92
175
89
150
86
140
83
122

106
208
105
184
103
159
100
137
98
129
94
112

131
257
130
227
126
195
123
169
120
158
115
137

144
266
144
236
141
206
137
178
135
167
130
146

178
306
177
271
174
236
169
203
166
191
159
167

182
434
184
389
182
342
178
297
175
280
170
246

223
601
225
537
222
471
217
408
213
384
206
338

1500
1200
1000
900
750

C - 110

SELECTION Parallel Shaft Triple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

*
*
*
*
*
*

20.812

19.984

1100
922
742
620
559
468

1500
1290
1070
919
838
701

*
*
*
*
*
*

*
*
*
*
*
*

981 1140 1340 1500

821 982 1140 1290
660 801 919 1070
552 670 769 919
498 605 693 841
416 506 580 708

24.782 25.651 24.717 24.630 25.908 25.313

713 898 1060

612 752 888
497 604 714
416 505 597
375 456 538
313 381 450
C-146 C-146 C-146
C-172 C-172 C-172

1250
1080
895
757
683
571
C-146
C-172

1340
1150
954
812
732
612
C-146
C-172

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

90
1800
75
1500
20
60
1200
50
1000
45
900
38
750
21.793 21.793 Exact Reduction Ratio
80
1800
3290 3430
67
1500
2650 2840
22.4
54
1200
2220 2440
45
1000
2000 2230
40
900
1670 1910
33
750
24.930 24.930 Exact Reduction Ratio
72
1800
2890 3060
60
1500
2320 2530
25
48
1200
1940 2170
40
1000
1750 1990
36
900
1470 1710
30
750
C-150 C-150 Horizontal
Dimension
Vertical
Tables
Upright

22.841 22.335 22.781 22.930 22.648

758
650
539
462
423
355

Nominal Reduction Ratio 20 25

1590
1400
1190
1050
955
796
C-148

* marked models are double reduction units. Refer to C-108 and C-109.

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
296
651
301
590
301
524
297
458
294
433
285
383

333
713
340
647
340
575
336
503
332
475
322
421

391
813
399
738
397
653
391
569
386
538
375
475

429
867
436
784
435
694
428
605
423
572
410
506

238

265

298

348

386

1800

248

278

313

367

404

1500 Reduction

663
1095
701
1157
723
1193
726
1199
724
1195
714
1178

663
1095
701
1157
723
1193
726
1199
724
1195
714
1178

252

285

321

377

412

1200

251

285

321

375

411

1000

249

283

319

372

408

900

Triple

277

313

364

399

2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
r/min
Ratio
Fans

Without Fan With Fan

1800
1.00
20
1.00
1
Triple
0.85
30
0.87
1500 Reduction
1
Horizontal
0.70
40
0.73
1200
Type
1
0.55
50
0.60
1000
1
20

900
1
25
0QVGU
750
1

264
603
267
545
266
481
262
419
258
396
250
349

243

1.
For marked values, the forced
oil lubrication is required at
continuous operation.

Temperature

Size of Reducer
481
794
486
801
481
794
472
779
465
768
451
744

0QVGU

750

1
1
1
1
1
1

1800

Vertical
Type

20

25

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

20

25

750

C - 111

SELECTION Parallel Shaft Triple Reduction

Nominal Reduction Ratio 28 35.5

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
64
1500
54
28
1200
43
1000
36
900
32
750
27
Exact Reduction Ratio
1800
57
1500
48
31.5
1200
38
1000
32
900
29
750
24
Exact Reduction Ratio
1800
51
1500
42
35.5
1200
34
1000
28
900
25
750
21
Horizontal
Dimension
Vertical
Tables
Upright

28.565 27.764 27.350 27.481 28.269 28.761 29.227 27.426 28.995 27.231 28.105 27.880 26.961 26.838 27.992

17.4
14.5
11.7
9.7
8.8
7.3

28.0
23.4
18.8
15.7
14.1
11.8

44
37
29.7
24.8
22.3
18.6

31.401

31.905 32.876 31.625 31.213 31.498 30.855 31.992 29.905 31.202 31.500 31.056 31.601 29.792 31.855

16.9
14.1
11.3
9.4
8.5
7.1

26.1
21.8
17.4
14.5
13.1
10.9

38
31
25.5
21.3
19.2
16.0

58
48
39
32
29.5
24.6
51
42
34
28.8
25.9
21.7

65
54
43
36
32
27
63
52
42
35
31
26.6

84
70
56
47
42
35
81
68
54
45
40
34

97
81
65
54
49
41
98
82
66
55
49
41

132
111
89
74
67
56
126
105
84
71
64
53

154
129
103
86
78
65
163
136
109
91
82
69

209
175
140
117
106
88
208
174
140
117
105
88

249
208
167
140
126
105
239
200
160
134
121
101

329
275
221
185
167
139
315
264
212
177
159
133

395
330
265
222
200
167
355
297
238
199
179
150

502
420
337
282
254
212
481
402
323
270
244
203

558
467
375
314
283
236
511
427
343
287
259
216

36.321 36.406 35.438 34.383 35.617 35.833 35.127 35.942 34.848 35.686 35.294 34.850 34.854 32.712 34.652

13.7 21.4
34
46
51
68
81
101
128
160
199
265
307
413 453
11.5 17.9 28.6
39
43
57
68
85
107
134
167
221
257
346 379
9.2 14.4 23.0
31
34
45
54
68
86
107
134
178
206
278 304
7.7 12.0 19.2 26.2 29.0
38
45
57
72
90
112
148
172
232 254
6.9 10.8 17.3 23.6 26.1
34
41
51
65
81
101
134
155
209 229
5.8
9.0 14.4 19.7 21.8 28.8
34
43
54
67
84
112
130
175 191
C-142 C-142 C-142 C-142 C-142 C-142 C-142 C-142 C-144 C-144 C-144 C-144 C-144 C-144 C-146
C-168 C-168 C-168 C-168 C-168 C-168 C-168 C-168 C-170 C-170 C-170 C-170 C-170 C-170 C-172
C-184 C-184 C-184 C-184 C-184 C-184 C-184 C-184 C-186 C-186 C-186 C-186 C-186 C-186

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
21
32
39
49
58
70
74
92
104
124
140
171
177
218 230
1800
1
60
84
72
104
142
172
179
222
203
243
258
295
422
586 545
Triple
21
31
38
48
56
69
72
90
102
123
137
170
176
218 229
Reduction 1500
1
51
72
62
91
122
150
156
194
178
215
226
260
372
521 484
Horizontal
19
30
36
46
53
66
69
87
98
119
133
165
171
214 225
1200
Type
1
43
61
52
77
103
128
132
166
152
184
194
225
322
454 421
18
28
34
44
51
64
66
84
94
115
128
161
166
208 219
1000
1
36
51
44
65
87
110
112
142
129
158
166
193
277
392 363
28
18
27
33
43
49
62
64
82
92
113
125
157
162
205 215

900
1
33
48
41
61
81
102
104
132
121
148
155
181
259
369 341
35.5
17
26
31
41
46
59
61
78
87
108
119
151
156
197 206
750
1
28
41
35
52
69
88
90
115
104
129
135
158
226
323 298

Triple
Reduction
Vertical
Type

28

35.5

Triple
Reduction
Upright
Type

28

35.5

1800

21

31

37

47

55

68

70

87

98

117

132

161

165

201

211

1500

20

30

36

46

54

67

69

86

97

117

131

162

167

205

217

1200

19

29

35

45

52

65

67

84

95

115

129

160

165

205

216

1000

18

27

33

43

50

62

65

82

92

112

125

156

161

202

212

900

17

27

32

42

48

61

63

80

90

110

122

153

158

199

209

750

16

25

30

40

46

58

60

76

86

106

117

148

152

193

202

1800

1
1
1
1
1
1

21
60
21
51
19
43
18
36
18
33
17
28

39
72
38
62
36
52
34
44
33
41
31
35

49
104
48
90
46
77
44
65
43
61
41
52

65
158
62
136
59
115
56
97
55
90
51
77

70
172
69
150
66
128
64
110
62
102
59
88

74
179
72
156
69
132
66
112
64
104
61
90

91
220
89
193
86
165
83
141
81
132
77
114

104
203
102
178
98
152
94
129
92
121
87
104

124
243
123
215
119
184
115
158
113
148
108
129

140
258
137
226
133
194
128
166
125
155
119
135

170
292
169
258
165
224
160
193
157
181
151
158

177
422
176
372
171
322
166
277
162
259
156
226

216
582
216
518
213
452
208
391
204
368
197
323

1500
1200
1000
900
750

C - 112

32
84
31
72
30
61
28
51
27
48
26
41

SELECTION Parallel Shaft Triple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
28.552 27.527 28.078 28.261 27.914

624
535
444
378
341
285

800
669
538
450
405
339
722
604
485
406
366
306

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

64
1800
2550 2750
54
1500
2050 2280
28
43
1200
1720 1960
36
1000
1550 1790
32
900
1290 1530
27
750
31.826 31.826 31.115 32.390 32.390 Exact Reduction Ratio
1730 1870 2460
57
1800
1450 1600 2060 2240 2450
48
1500
1160 1330 1660 1800 2030
31.5
38
1200
977 1130 1380 1500 1740
32
1000
881 1020 1250 1360 1590
29
900
736 857 1040 1130 1340
24
750
36.000 36.000 36.500 34.341 34.341 Exact Reduction Ratio
1530 1690 2110
51
1800
1280 1450 1760 2110 2340
42
1500
1030 1200 1420 1700 1940
35.5
34
1200
866 1000 1180 1420 1660
28
1000
780 908 1070 1280 1510
25
900
652 759 895 1070 1260
21
750
C-148 C-148 C-150 C-150 C-150 Horizontal
Dimension
Vertical
Tables
Upright
29.333 29.333 28.679 28.315 28.315

1870
1570
1260
1050
954
798

957 1110 1260

813 932 1080
653 749 896
546 626 768
492 565 703
412 472 603

30.978 32.067 30.463 30.789 31.932 31.197

588
497
400
334
301
252

Nominal Reduction Ratio 28 35.5

865 1040 1120 1530

724 898 963 1280
581 727 791 1030
486 608 661 865
438 548 596 780
366 458 499 653

35.345 34.412 35.100 35.329 34.895 36.870

525 643 781 895 1040 1300

450 538 653 749 899 1090
366 432 525 602 745 878
306 361 439 503 639 735
276 325 395 454 581 662
231 272 330 379 485 554
C-146 C-146 C-146 C-146 C-146 C-148
C-172 C-172 C-172 C-172 C-172

2000
1720
1430
1220
1110
929

2640
2230
1790
1500
1350
1130

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
508
838
515
849
512
845
504
831
497
820
483
796

294
647
295
577
290
504
283
436
278
410
268
360

323
691
325
618
319
538
310
465
305
437
294
383

378
786
377
697
369
607
359
523
353
491
340
431

417
842
421
757
415
661
403
570
395
535
380
468

231

267

292

344

380

1800

235

277

304

356

393

1500 Reduction

508
838
515
849
512
845
504
831
497
820
483
796

564
931
577
952
579
955
572
943
565
933
551
909

657
1084
682
1125
689
1137
683
1128
677
1117
661
1091

657
1084
682
1125
689
1137
683
1128
677
1117
661
1091

233

277

306

355

398

1200

229

273

301

348

391

1000

225

270

296

343

385

900

750

1
1
1
1
1
1

1800

Triple

262

287

332

373

2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
r/min
Ratio
Fans

Without Fan With Fan

1800
1.00
20
1.00
1
Triple
0.85
30
0.87
1500 Reduction
1
Horizontal
0.70
40
0.73
1200
Type
1
0.55
50
0.60
1000
1
28

900
1
35.5
0QVGU
750
1

250
572
248
506
243
439
236
378
231
355
222
310

218

1.
For marked values, the forced
oil lubrication is required at
continuous operation.

Temperature

Size of Reducer
467
770
466
769
458
756
448
739
440
726
426
702

0QVGU

Vertical
Type

28

35.5

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

28

35.5

750

C - 113

SELECTION Parallel Shaft Triple Reduction

Nominal Reduction Ratio 40 50

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
45
1500
38
40
1200
30
1000
25
900
23
750
19
Exact Reduction Ratio
1800
40
1500
33
45
1200
27
1000
22
900
20
750
17
Exact Reduction Ratio
1800
36
1500
30
50
1200
24
1000
20
900
18
750
15
Horizontal
Dimension
Vertical
Tables
Upright

38.980 39.444 41.134 40.976 38.889 39.686 40.435 38.450 39.190 37.500 39.375 39.000 38.519 38.514 39.818

13.6
11.4
9.1
7.6
6.9
5.7

21.2
17.7
14.2
11.9
10.7
8.9

30
25.5
20.4
17.1
15.4
12.8

39
33
26.7
22.3
20.1
16.8

50
42
34
28.5
25.6
21.4

64
53
42
35
32
26.7

75
63
50
42
38
31

105
88
70
59
53
44

125
104
84
70
63
52

174
145
116
96
87
72

192
160
129
107
97
81

252
211
169
141
127
106

292
244
196
164
147
123

374
313
251
210
189
158

411
343
276
230
207
173

45.088 45.009 44.338 44.550 44.375 45.148 46.033 43.197 45.667 42.889 44.118 43.765 42.484 42.289 43.316

11.1
9.3
7.4
6.2
5.6
4.7

17.4
14.5
11.6
9.7
8.7
7.3

27.5
22.9
18.4
15.4
13.8
11.5

36
30
24.3
20.3
18.3
15.3

41
34
27.9
23.3
21.0
17.5

54
45
36
30
27.4
22.9

62
52
41
34
31
26.2

85
71
57
47
42
35

98
82
66
55
49
41

134
112
90
75
67
56

160
134
107
89
81
67

212
177
142
118
107
89

253
211
170
142
128
106

321
269
216
180
162
135

364
304
244
204
184
153

51.141 51.268 49.248 49.444 49.634 50.388 48.825 49.144 51.188 48.750 51.845 46.944 51.911

24.6
31
40
51
61
81
100
133
148
203
218
308 316
20.5 26.7
33
43
51
67
84
111
124
169
182
257 264
16.5 21.4 27.0
34
41
54
67
89
99
136
146
207 212
13.8 17.9 22.5 28.9
34
45
56
74
83
113
122
173 177
12.4 16.1 20.3 26.0
31
40
50
67
74
102
110
155 160
10.3 13.4 16.9 21.6 26.0
34
42
56
62
85
92
130 133
C-142 C-142 C-142 C-142 C-142 C-142 C-142 C-142 C-144 C-144 C-144 C-144 C-144 C-144 C-146
C-168 C-168 C-168 C-168 C-168 C-168 C-168 C-168 C-170 C-170 C-170 C-170 C-170 C-170 C-172
C-184 C-184 C-184 C-184 C-184 C-184 C-184 C-184 C-186 C-186 C-186 C-186 C-186 C-186

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
20
31
34
46
53
66
66
83
92
113
125
157
159
201 210
1800
1
57
80
63
97
130
162
159
200
180
221
230
270
377
540 497
Triple
20
30
33
44
51
63
64
80
89
110
121
154
155
198 206
Reduction 1500
1
49
69
54
83
111
137
137
173
155
192
199
235
328
473 434
Horizontal
18
28
30
42
48
60
60
77
84
106
115
148
148
191 198
1200
Type
1
41
58
44
70
92
116
115
146
130
164
168
201
279
406 371
17
27
29
39
45
57
57
73
80
101
110
142
142
185 191
1000
1
34
49
37
58
77
98
96
124
110
139
142
171
237
348 317
40
17
26
27
38
43
55
55
71
78
99
106
138
138
180 186

900
1
31
45
34
54
71
90
89
115
102
130
132
159
220
325 295
50
16
24
25
36
40
52
51
67
73
94
101
132
131
172 177
750
1
27
39
29
46
60
78
76
99
87
112
113
138
190
283 256

Triple
Reduction
Vertical
Type

40

50

Triple
Reduction
Upright
Type

40

50

1800

20

29

33

44

51

64

64

80

88

108

119

150

151

190

199

1500

19

29

32

43

50

62

62

78

86

107

117

148

149

189

198

1200

18

27

30

41

47

59

59

75

82

103

112

144

144

185

192

1000

17

26

28

39

44

56

56

72

78

99

108

139

139

180

186

900

16

25

27

37

43

54

54

70

76

97

105

136

136

177

182

750

15

24

25

35

40

51

51

66

72

92

99

130

129

170

174

1800

1
1
1
1
1
1

20
57
20
49
18
41
17
34
17
31
16
27

31
80
30
69
28
58
27
49
26
45
24
39

34
63
33
54
30
44
29
37
27
34
25
29

46
97
44
83
42
70
39
58
38
54
36
46

59
145
57
125
54
105
52
88
50
82
47
70

66
162
63
137
60
116
57
98
55
90
52
78

66
159
64
137
60
115
57
96
55
89
51
76

83
200
80
173
77
146
73
124
71
115
67
99

92
180
89
155
84
130
80
110
78
102
73
87

113
221
110
192
106
164
101
139
99
130
94
112

125
230
121
199
115
168
110
142
106
132
101
113

157
270
154
235
148
201
142
171
138
159
132
138

159
377
155
328
148
279
142
237
138
220
131
190

201
540
198
473
191
406
185
348
180
325
172
283

1500
1200
1000
900
750

C - 114

SELECTION Parallel Shaft Triple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 40 50

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

45
1800
38
1500
40
30
1200
25
1000
23
900
19
750
45.900 45.900 44.321 43.686 43.686 Exact Reduction Ratio
1210 1380 1740
40
1800
1010 1180 1460 1670 1910
33
1500
816 949 1170 1340 1580
45
27
1200
682 794 981 1120 1320
22
1000
615 715 885 1010 1190
20
900
514 598 740 848 1000
17
750
49.800 49.800 48.087 49.974 49.974 Exact Reduction Ratio
1120 1280 1610
36
1800
937 1090 1340 1460 1700
30
1500
753 876 1080 1170 1390
50
24
1200
629 732 906 986 1160
20
1000
567 660 817 889 1040
18
900
474 552 682 742 876
15
750
C-148 C-148 C-150 C-150 C-150 Horizontal
Dimension
Vertical
Tables
Upright

38.349 39.522 38.082 37.948 39.918 39.000 39.059 39.059 39.601 39.284 39.284

482
403
324
271
244
204

589
492
395
330
298
249

695
581
467
390
352
294

875
738
593
495
447
373

933 1190 1420 1570 1940

791 1030 1180 1350 1630 1850 2080
635 831 955 1110 1310 1490 1730
531 695 799 930 1090 1240 1470
479 627 720 839 988 1120 1320
400 524 602 701 826 941 1110

44.182 42.412 43.261 43.543 43.008 46.838

432
366
294
246
222
185

524
438
352
294
265
221

636
532
427
357
322
269

730
610
490
410
369
308

876 1030
751 865
623 695
524 581
473 523
395 437

47.936 50.361 46.936 48.355 49.198 48.067

388 464 566 695 770 1000

324 388 474 581 644 843
260 311 380 467 517 677
217 260 318 390 432 566
196 234 286 352 390 510
163 196 239 294 326 426
C-146 C-146 C-146 C-146 C-146 C-148
C-172 C-172 C-172 C-172 C-172

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
488
805
489
807
482
795
471
777
463
764
448
739

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
440
726
434
715
421
695
408
673
399
659
383
632

0QVGU

488
805
489
807
482
795
471
777
463
764
448
739

545
899
550
908
546
901
537
886
529
873
514
847

631
1042
641
1058
639
1055
630
1039
622
1026
604
997

631
1042
641
1058
639
1055
630
1039
622
1026
604
997

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
Ratio
r/min
Fans

Without Fan With Fan

1800
1.00
20
1.00
1
Triple
0.85
30
0.87
1500 Reduction
1
Horizontal
0.70
40
0.73
1200
Type
1
0.55
50
0.60
1000
1
40

900
1
50
0QVGU
750
1

238
545
236
481
230
416
223
358
219
335
210
293

274
603
270
529
262
454
253
389
247
364
236
316

307
656
305
581
299
505
291
435
285
409
275
358

363
756
357
661
344
566
332
483
324
451
309
392

396
801
393
706
383
611
371
525
364
493
350
431

223

259

286

340

373

1800

225

258

289

343

374

1500

222

253

288

334

370

1200

217

246

282

324

362

1000

40

213

241

278

317

356

900

50

206

232

269

304

343

750

1
1
1
1
1
1

1800

Triple
Reduction
Vertical
Type

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

40

50

750

C - 115

SELECTION Parallel Shaft Triple Reduction

Nominal Reduction Ratio 56 71

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
32
1500
27
56
1200
21
1000
18
900
16
750
13
Exact Reduction Ratio
1800
29
1500
24
63
1200
19
1000
16
900
14
750
12
Exact Reduction Ratio
1800
25
1500
21
71
1200
17
1000
14
900
13
750
11
Horizontal
Dimension
Vertical
Tables
Upright

55.125 55.739 56.195 56.250 56.507 56.608 56.894 56.206 57.353 54.706 57.182 51.547 56.471

22.1
18.5
14.8
12.4
11.1
9.3

29.1
24.3
19.5
16.2
14.6
12.2

33
27.6
22.1
18.5
16.6
13.9

43
36
29.3
24.5
22.1
18.4

50
42
34
28.5
25.6
21.4

65
54
43
36
32
27.4

79
66
53
44
40
33

102
86
69
57
51
43

123
103
83
69
62
52

170
142
114
95
86
71

189
158
126
105
95
79

264
221
177
148
133
111

280
234
188
157
141
118

63.986 63.741 61.358 62.615 65.045 61.852 63.984 61.225 63.984 63.375 63.194 63.186 64.889

19.7
16.5
13.2
11.0
9.9
8.3

25.7
21.5
17.2
14.4
13.0
10.8

32
27.1
21.7
18.1
16.3
13.6

40
33
27.1
22.6
20.3
16.9

47
39
31
26.5
23.9
19.9

66
55
44
37
33
27.8

77
64
51
43
38
32

106
88
71
59
53
44

119
99
79
66
60
50

156
131
105
87
79
66

179
150
120
100
90
75

230
192
154
129
116
97

254
212
170
142
128
107

68.971 69.300 70.014 71.234 74.051 69.488 74.559 70.024 71.691 71.118 69.700 69.381 70.588

17.7 23.4 26.6

34
39
53
60
82
99
131
155
197 225
14.8 19.6 22.2 29.0
32
44
50
69
83
109
130
165 188
11.9 15.7 17.8 23.2 26.1
35
40
55
66
88
104
132 151
9.9 13.1 14.8 19.4 21.8 29.7
34
46
55
73
87
110 126
8.9 11.8 13.4 17.5 19.6 26.8
30
41
50
66
78
99 113
7.4
9.8 11.2 14.6 16.4 22.4 25.6
34
41
55
65
83
95
C-142 C-142 C-142 C-142 C-142 C-142 C-144 C-144 C-144 C-144 C-144 C-144 C-146
C-168 C-168 C-168 C-168 C-168 C-168 C-170 C-170 C-170 C-170 C-170 C-170 C-172
C-184 C-184 C-184 C-184 C-184 C-184 C-186 C-186 C-186 C-186 C-186 C-186

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
32
39
49
59
62
78
86
106
119
146
152
186 198
1800
1
59
83
120
145
150
188
169
208
219
250
362
500 469
Triple
30
37
47
57
60
75
83
102
115
141
148
181 194
Reduction 1500
1
50
70
102
124
128
161
145
178
189
216
314
432 409
Horizontal
28
35
44
53
56
70
79
96
109
134
142
172 187
1200
Type
1
42
58
85
103
107
134
122
149
160
182
267
366 350
27
33
41
50
53
66
75
92
104
127
136
165 180
1000
1
34
48
71
86
90
112
103
126
135
153
227
310 298
56
26
31
40
48
51
64
73
89
101
123
132
160 175

900
1
32
44
65
79
83
104
95
117
125
142
211
289 278
71
24
29
37
45
48
60
68
83
95
116
125
152 167
750
1
27
38
55
67
71
89
82
99
108
122
182
249 241

Triple
Reduction
Vertical
Type

56

71

Triple
Reduction
Upright
Type

56

71

1800

31

38

47

58

60

75

83

102

114

140

145

178

188

1500

30

36

46

55

58

73

81

99

111

137

143

175

187

1200

28

34

43

52

55

69

77

94

107

131

138

168

182

1000

26

32

41

49

52

65

74

90

102

125

133

162

176

900

25

31

39

47

51

63

72

87

100

122

130

157

172

750

24

29

37

44

48

59

68

82

94

115

124

150

164

1800

1
1
1
1
1
1

32
59
30
50
28
42
27
34
26
32
24
27

39
83
37
70
35
58
33
48
31
44
29
38

54
133
52
113
49
94
46
79
44
72
41
61

59
145
57
124
53
103
50
86
48
79
45
67

62
150
60
128
56
107
53
90
51
83
48
71

78
188
75
161
70
134
66
112
64
104
60
89

86
169
83
145
79
122
75
103
73
95
68
82

106
208
102
178
96
149
92
126
89
117
83
99

119
219
115
189
109
160
104
135
101
125
95
108

146
250
141
216
134
182
127
153
123
142
116
122

152
362
148
314
142
267
136
227
132
211
125
182

186
500
181
432
172
366
165
310
160
289
152
249

1500
1200
1000
900
750

C - 116

SELECTION Parallel Shaft Triple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 56 71

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

32
1800
1360 1600
27
1500
1090 1290
56
21
1200
916 1080
18
1000
826 974
16
900
690 814
13
750
62.494 62.494 62.372 61.592 61.592 Exact Reduction Ratio
897 1040 1240
29
1800
750 873 1040 1190 1410
24
1500
602 701 839 960 1130
63
19
1200
503 586 701 802 946
16
1000
454 528 632
723 853
14
900
379 441 528
604 713
12
750
72.000 72.000 70.853 72.791 72.791 Exact Reduction Ratio
780 908 1100
25
1800
652 759 922 1010 1190
21
1500
524 610 740 814 961
71
17
1200
438 509 618 681 803
14
1000
394 459 557 613 724
13
900
329 383 466 512 604
11
750
C-148 C-148 C-150 C-150 C-150 Horizontal
Dimension
Vertical
Tables
Upright

57.600 54.044 55.125 55.485 54.803 56.807 57.600 57.600 57.487 53.842 53.842

338
282
226
189
170
142

413
345
277
231
208
174

502
419
336
281
253
212

575
481
386
322
291
243

717
615
494
413
372
311

856
716
575
480
433
362

62.494 62.070 59.809 59.598 62.691 61.933

299
249
200
167
151
126

378
316
253
212
191
159

446
373
299
250
225
188

566
473
380
317
286
239

607
508
408
340
307
256

786
657
528
441
397
332

72.000 66.609 67.941 68.385 67.544 73.193

271 336 408 468 599 667

226 281 341 391 501 558
182 225 274 314 402 448
152 188 229 262 336 374
137 170 206 236 303 337
114 141 172 197 253 281
C-146 C-146 C-146 C-146 C-146 C-148
C-172 C-172 C-172 C-172 C-172

972
812
652
545
492
411

1130
946
759
635
572
478

1350
1130
909
760
685
572

9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
448
739
443
731
432
712
418
690
410
676
393
648

262
576
258
504
249
433
241
371
235
346
225
301

288
617
283
539
273
462
264
395
257
369
246
320

337
700
329
610
318
522
306
445
298
415
284
361

378
764
370
664
356
567
342
483
333
451
318
391

205

248

274

321

362

1800

202

247

272

318

357

1500 Reduction

448
739
443
731
432
712
418
690
410
676
393
648

512
845
509
840
498
821
484
799
475
784
457
754

591
975
592
977
583
962
570
940
560
924
540
891

591
975
592
977
583
962
570
940
560
924
540
891

196

242

266

309

347

1200

189

235

258

299

335

1000

185

230

252

293

328

900

750

1
1
1
1
1
1

1800

Triple

221

242

280

313

2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
Ratio
r/min
Fans

Without Fan With Fan

1800
1.00
20
1.00
1
Triple
0.85
30
0.87
1500 Reduction
1
Horizontal
0.70
40
0.73
1200
Type
1
0.55
50
0.60
1000
1
56

900
1
71
0QVGU
750
1

214
491
210
427
201
364
193
310
188
289
179
250

177

1.
For marked values, the forced
oil lubrication is required at
continuous operation.

Temperature

Size of Reducer
422
696
413
681
398
657
384
633
375
618
358
591

0QVGU

Vertical
Type

56

71

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

56

71

750

C - 117

SELECTION Parallel Shaft Triple Reduction

Nominal Reduction Ratio 80 90

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

23
1800
19
1500
80
15
1200
13
1000
11
900
9.4
750
Exact Reduction Ratio
20
1800
17
1500
90
13
1200
11
1000
10
900
8.3
750
Horizontal
Dimension
Vertical
Tables
Upright

*
*
*
*
*
*
*
*
*
*
*
*

79.751

78.012

81.056

80.234

79.219

20.6
17.2
13.8
11.5
10.4
8.7

32
27.4
21.9
18.3
16.5
13.7

50
42
33
28.3
25.5
21.3

82
68
55
45
41
34

125
105
84
70
63
53

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

86.706

88.750

91.063

91.765

88.897

18.8
15.7
12.6
10.5
9.4
7.9
C-142
C-168
C-184

27.9
23.3
18.7
15.6
14.0
11.7
C-142
C-168
C-184

40
34
27.3
22.8
20.5
17.1
C-142
C-168
C-184

63
53
42
35
32
26.7
C-144
C-170
C-186

105
88
70
59
53
44
C-144
C-170
C-186

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

77.018 77.090

*
*
*
*
*
*

189
158
127
106
95
79

206
172
138
115
104
87

84.569

*
*
*
*
*
*

162
*
136
*
109
*
91
*
82
*
68
*
C-144 C-146
C-170 C-172
C-186

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
37
56
73
100
139
178 202
1800
1
79
137
177
196
238
479 479
Triple
36
54
70
96
134
173 198
Reduction 1500
1
67
118
151
167
205
414 417
Horizontal
33
50
66
91
127
165 190
1200
Type
1
55
97
126
141
173
351 356
31
47
62
86
121
158 183
1000
1
46
81
106
118
146
297 304
80
30
45
60
83
117
153 178

900
1
42
74
97
109
135
276 283
90
28
42
56
78
111
145 170
750
1
36
63
83
93
116
238 246

Triple
Reduction
Vertical
Type

80

90

Triple
Reduction
Upright
Type

80

90

1800

36

55

71

96

134

171

192

1500

35

52

69

93

130

168

190

1200

33

49

65

89

125

161

185

1000

31

47

61

85

119

155

179

900

29

45

59

82

116

151

175

750

27

42

56

77

109

143

167

1800

1
1
1
1
1
1

37
79
36
67
33
55
31
46
30
42
28
36

56
137
54
118
50
97
47
81
45
74
42
63

73
177
70
151
66
126
62
106
60
97
56
83

100
196
96
167
91
141
86
118
83
109
78
93

139
238
134
205
127
173
121
146
117
135
111
116

178
479
173
414
165
351
158
297
153
276
145
238

1500
1200
1000
900
750

C - 118

SELECTION Parallel Shaft Triple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
78.118 75.300 73.714 80.819 77.266 75.490 78.118 78.118 76.873

240
200
160
134
121
101

298
249
200
167
150
125

85.313

363
304
244
203
183
153

397
332
266
222
200
167

83.332

495
413
332
277
250
208

647
541
434
363
327
273

720
602
483
404
364
304

839
701
563
470
424
354

1010
851
683
571
514
430

91.315 89.216 85.313 85.313 86.903

220
322
420 549 661 769 902
*
*
183
269
351 459 552 643 754
*
*
147
216
281 368 443 516 605
*
*
123
180
235 308 370 431 506
*
*
111
162
212 277 334 388 456
*
*
92
135
177 231 278 324 380
*
*
C-146 C-146 C-146 C-146 C-146 C-148 C-148 C-148 C-150
C-172 C-172 C-172 C-172 C-172

Nominal Reduction Ratio 80 90

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

23
1800
19
1500
80
15
1200
13
1000
11
900
9.4
750
Exact Reduction Ratio
20
1800
17
1500
90
13
1200
11
1000
10
900
8.3
750
Horizontal
Dimension
Vertical
Tables
Upright

* marked models are quadruple reduction units. Refer to C-120 and C-121.

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126
399
659
389
642
373
615
358
591
349
576
332
548

446
735
441
727
429
708
415
685
406
670
389
642

446
735
441
727
429
708
415
685
406
670
389
642

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

500
1800
1.00
20
1.00
825
1
495
Triple
0.85
30
0.87
1500
817
1
Reduction
0.70
482
40
0.73
Horizontal
1200
796
1
Type
0.55
50
0.60
468
1000
80
772
1

459
900
90
757
1
0QVGU
440
750
726
1

214
490
209
426
201
363
193
309
188
288
179
250

265
582
260
510
252
438
243
374
237
350
227
304

283
606
278
530
269
454
259
388
253
362
241
315

333
693
326
604
314
516
302
440
295
411
281
357

362
732
354
636
340
543
327
462
319
431
304
374

204

251

269

319

347

1800

202

250

268

315

343

1500 Reduction

196

244

261

306

332

1200

189

237

253

296

321

1000

185

233

248

290

314

900

750

1
1
1
1
1
1

1800

Triple

176

223

238

277

300

Vertical
Type

80

90

Triple

1500 Reduction
1200
1000
900

Upright
Type

1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

80

90

750

C - 119

SELECTION Parallel Shaft Quadruple Reduction

Nominal Reduction Ratio 80 100

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
23
1500
19
80
1200
15
1000
13
900
11
750
9.4
Exact Reduction Ratio
1800
20
1500
17
90
1200
13
1000
11
900
10
750
8.3
Exact Reduction Ratio
1800
18
1500
15
100
1200
12
1000
10
900
9.0
750
7.5
Horizontal
Dimension
Vertical
Tables
Upright

82.394

79.669

79.341

76.744

78.120

15.3
12.8
10.3
8.6
7.7
6.4

25.0
20.9
16.7
13.9
12.6
10.5

32
27.2
21.7
18.1
16.3
13.6

50
41
33
27.9
25.1
20.9

82
68
54
45
41
34

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

79.124

*
*
*
*
*
*

134
111
89
74
67
55

88.813

90.908

90.326

89.427

87.529

87.269

13.8
11.5
9.2
7.7
6.9
5.8

20.5
17.1
13.7
11.5
10.3
8.6

32
26.7
21.4
17.9
16.1
13.4

50
41
33
27.9
25.1
20.9

81
68
54
45
41
34

124
104
83
69
62
52

*
*
*
*
*
*

103.09 102.69

99.26

*
*
*
*
*
*
101.29

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*
88.471

*
*
*
*
*
*

180
150
120
101
91
75

103.97 98.871 100.57

97.650 96.720 96.444 96.432 101.66

12.3 16.1 20.1 25.1 29.8

32
49
10.3 13.4 16.8 20.9 24.9 27.2
41
8.2 10.7 13.5 16.7 19.9 21.7
33
6.9
9.0 11.2 13.9 16.6 18.1 27.6
6.2
8.1 10.1 12.6 15.0 16.3 24.9
5.2
6.7
8.4 10.5 12.5 13.6 20.7
C-152 C-152 C-152 C-152 C-152 C-152 C-154
C-174 C-174 C-174 C-174 C-174 C-174 C-176
C-188 C-188 C-188 C-188 C-188 C-188 C-190

78
82
118
134 163
65
68
99
111 136
52
54
79
89 109
43
45
66
74
91
39
41
59
67
82
33
34
49
55
68
C-154 C-154 C-154 C-154 C-156
C-176 C-176 C-176 C-176 C-178
C-190 C-190 C-190 C-190

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple 1800
27
34
42
51
52
65
73
100
122
128
155 157
Reduction
26
32
41
50
50
62
71
97
118
125
151 156
1500
Horizontal
24
30
39
47
47
59
67
93
113
120
145 152
1200
Type
23
29
37
45
45
56
64
89
108
115
139 148
1000
80
22
28
36
43
44
54
62
86
105
112
135 145
900

21
26
34
41
41
51
59
82
99
107
128 139
750
100
Quadruple
Reduction
Vertical
Type

80

100
Quadruple
Reduction
Upright
Type

80

100

C - 120

1800
1500
1200
1000
900
750

28
27
25
24
23
21

35
33
31
29
28
26

45
43
40
38
37
34

54
51
48
46
44
41

54
52
49
46
45
42

67
64
60
57
55
51

77
73
69
65
63
60

105
101
96
91
88
83

128
123
116
110
107
101

136
131
124
119
115
109

164
157
149
142
138
130

1800
1500
1200
1000
900
750

27
26
25
23
22
21

34
32
31
29
28
26

47
45
43
41
39
37

51
50
47
45
43
41

52
50
48
45
44
41

65
63
59
56
54
51

74
71
68
64
62
59

101
98
93
89
87
82

124
120
114
108
105
100

130
126
121
116
113
107

157
153
146
139
136
129

172
167
160
154
150
143

SELECTION Parallel Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
80.205 80.205

*
*
*
*
*
*
*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

88.676

91.041

254
212
170
142
128
106

353
295
237
198
178
149

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

1100 1210
922 1060
740 872
618 727
557 654
465 545
89.191 89.191

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

*
*
*
*
*
*

994 1170
831 980
667 786
557 657
502 592
419 494

97.907 101.85 98.135 97.789 102.87 96.134 101.59 101.59 98.178 102.03 102.03

192 232 274 348 373 465 556 648 800 871 1020
160 194 229 290 312 388 465 541 669 728 858
128 155 184 233 250 310 373 434 537 584 689
107 129 153 194 209 258 311 363 448 488 575
96 117 138 175 188 232 281 327 404 439 518
80
97 115 146 157 194 234 273 337 367 433
C-156 C-156 C-156 C-156 C-156 C-158 C-158 C-158 C-160 C-160 C-160
C-178 C-178 C-178 C-178 C-178

Nominal Reduction Ratio 80 100

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

23
1800
19
1500
80
15
1200
13
1000
11
900
9.4
750
Exact Reduction Ratio
20
1800
17
1500
90
13
1200
11
1000
10
900
8.3
750
Exact Reduction Ratio
18
1800
15
1500
100
12
1200
10
1000
9.0
900
7.5
750
Horizontal
Dimension
Vertical
Tables
Upright

* marked models are triple reduction units. Refer to C-118 and C-119.

9095 9100 9105 9110 9115 9118 9121 9126 9128

204
203
199
193
190
182

230
228
223
217
213
205

271
268
261
253
248
238

299
295
286
277
271
260

193
187
179
172
167
159

225
219
210
202
197
188

252
245
235
226
221
211

294
286
273
262
256
244

323
313
299
287
280
267

328
322
311
300
293
280

392
386
374
362
354
339

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
177
175
170
165
162
155

0QVGU

392
386
374
362
354
339

425
422
413
402
395
381

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9131 9136
Ratio
r/min
Fans

Without Fan With Fan

521 521
1800 Quadruple
1.00
20
1.00
515 515
1500 Reduction
Horizontal
0.85
30
0.87
502 502
1200
Type
0.70
40
0.73
487 487
1000
80

478 478
900
0.55
50
0.60
100
460 460
750
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
80

900
100
750

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
80
900

750
100

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 121

SELECTION Parallel Shaft Quadruple Reduction

Nominal Reduction Ratio 112 140

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
16
1500
13
112
1200
11
1000
8.9
900
8.0
750
6.7
Exact Reduction Ratio
1800
14
1500
12
125
1200
9.6
1000
8.0
900
7.2
750
6.0
Exact Reduction Ratio
1800
13
1500
11
140
1200
8.6
1000
7.1
900
6.4
750
5.4
Horizontal
Dimension
Vertical
Tables
Upright

111.12

111.65

113.26

115.23

118.37 111.08 117.19 110.06 109.41 108.54 106.37 105.89 110.59

11.1
9.2
7.4
6.2
5.6
4.6

14.6
12.2
9.8
8.2
7.3
6.1

16.5
13.8
11.0
9.2
8.3
6.9

21.5
18.0
14.4
12.0
10.8
9.0

24.5
20.4
16.4
13.7
12.3
10.3

127.97

128.49

122.72

126.20

130.09 129.57 125.30 126.11 127.97 120.90 126.39 117.54 127.07

9.9
8.3
6.6
5.5
5.0
4.2

12.9
10.7
8.6
7.2
6.5
5.4

16.3
13.6
10.9
9.1
8.2
6.8

20.3
17.0
13.6
11.3
10.2
8.5

23.9
19.9
16.0
13.3
12.0
10.0

32
27.2
21.8
18.1
16.3
13.6
31
26.6
21.3
17.8
16.0
13.4

38
32
26.0
21.7
19.6
16.3
39
33
26.6
22.2
20.0
16.7

50
41
33
27.9
25.1
20.9
50
41
33
27.9
25.1
20.9

65
54
43
36
33
27.5
60
50
40
33
30
25.2

82
68
54
45
41
34
82
68
54
45
41
34

102
85
68
57
51
43
90
75
60
50
45
38

130
108
87
72
65
54
124
104
83
69
62
52

144
120
97
80
72
60
131
109
87
73
66
55

137.94 139.69 140.03 143.57 148.10 145.56 146.01 144.24 143.38 135.67 139.40 129.07 138.24

8.9 11.7 13.4 17.3 19.6 25.6

31
40
50
69
78
107 116
7.4
9.8 11.2 14.5 16.4 21.4 26.1
33
41
58
65
89
97
6.0
7.8
8.9 11.6 13.1 17.1 20.9 27.1
33
46
52
71
77
5.0
6.5
7.5
9.7 10.9 14.3 17.5 22.7 28.0
38
43
59
64
4.5
5.9
6.7
8.7
9.9 12.9 15.7 20.4 25.2
35
39
54
58
3.7
4.9
5.6
7.3
8.2 10.7 13.1 17.0 21.0 29.2
32
45
48
C-152 C-152 C-152 C-152 C-152 C-152 C-154 C-154 C-154 C-154 C-154 C-154 C-156
C-174 C-174 C-174 C-174 C-174 C-174 C-176 C-176 C-176 C-176 C-176 C-176 C-178
C-188 C-188 C-188 C-188 C-188 C-188 C-190 C-190 C-190 C-190 C-190 C-190

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple 1800
25
31
40
48
50
61
70
84
95
117
122
150 151
Reduction
24
30
38
46
48
59
68
81
92
113
119
146 149
1500
Horizontal
23
28
36
43
45
56
64
77
88
108
114
139 145
1200
Type
22
27
35
41
43
53
61
73
84
103
109
134 141
1000
112
21
26
34
40
42
51
59
71
82
100
106
130 138
900

20
24
32
38
39
48
56
67
77
95
101
124 132
750
140
Quadruple
Reduction
Vertical
Type

112

140
Quadruple
Reduction
Upright
Type

112

140

C - 122

1800
1500
1200
1000
900
750

27
25
24
22
21
20

33
31
29
27
26
24

42
40
37
35
34
32

50
47
45
42
41
38

52
50
47
44
43
40

64
61
57
54
52
49

73
70
66
62
60
57

88
84
79
75
72
68

100
96
90
86
83
79

122
117
111
105
102
96

129
124
118
112
109
103

158
151
144
137
133
126

1800
1500
1200
1000
900
750

26
25
23
22
21
20

31
30
28
27
26
24

44
43
40
38
37
35

48
46
43
41
40
38

50
48
46
43
42
39

62
59
56
53
51
48

71
68
65
61
60
56

84
81
77
73
71
67

96
93
89
84
82
78

118
114
108
103
100
95

124
120
115
110
107
102

152
147
140
134
131
124

164
159
152
146
143
136

SELECTION Parallel Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 112 140

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

16
1800
13
1500
112
11
1200
8.9
1000
8.0
900
6.7
750
126.78 123.87 127.49 127.49 127.34 129.91 129.91 Exact Reduction Ratio
304 397 445 518 619 686 810
14
1800
253 332 371 432 517 573 676
12
1500
203 266 298 347 415 460 542
125
9.6
1200
170 222 249 290 347 384 453
8.0
1000
153 200 224 261 312 346 408
7.2
900
127 167 187 218 261 289 341
6.0
750
135.09 146.39 146.88 146.88 142.35 133.32 133.32 Exact Reduction Ratio
303 337 387 450 555 669 789
13
1800
253 281 323 376 464 559 659
11
1500
203 226 259 301 372 448 529
140
8.6
1200
169 188 216 252 310 374 441
7.1
1000
152 170 195 227 280 337 398
6.4
900
127 142 162 189 233 281 332
5.4
750
C-156 C-158 C-158 C-158 C-160 C-160 C-160 Horizontal
Dimension
C-178
Vertical
Tables
Upright

112.80 109.29 111.48 112.21 110.83 113.61 117.50 117.50 117.37 109.93 109.93

174
145
116
97
87
73

206
172
138
115
104
86

251
209
168
140
126
105

287
240
192
161
145
121

122.38 124.14 120.95 119.20

154
128
103
86
77
64

191
159
127
106
96
80

223
186
149
124
112
94

286
239
191
160
144
120

141.00 133.22 135.88 136.77

139 170 206 236

116 141 172 197
93 113 138 158
78
95 115 132
70
85 104 119
58
71
86
99
C-156 C-156 C-156 C-156
C-178 C-178 C-178 C-178

368
308
247
206
186
155

433
362
290
242
218
182

482
403
323
270
243
203

561
469
376
314
283
236

671
561
450
376
338
283

9095 9100 9105 9110 9115 9118 9121 9126 9128

198
196
192
187
183
176

218
216
210
204
200
192

256
252
245
237
232
223

287
282
273
264
258
247

177
172
164
157
153
146

216
211
202
194
189
181

237
230
220
212
207
197

276
267
256
245
239
228

307
297
284
272
265
253

321
314
303
292
285
273

372
365
352
340
333
319

954
797
640
534
481
402

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
164
162
157
152
149
142

809
676
542
453
408
341

0QVGU

372
365
352
340
333
319

413
406
394
381
373
358

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9131 9136
Ratio
r/min
Fans

Without Fan With Fan

502 502
1800 Quadruple
1.00
20
1.00
493 493
1500 Reduction
Horizontal
0.85
30
0.87
476 476
1200
Type
0.70
40
0.73
461 461
1000
112

451 451
900
0.55
50
0.60
140
432 432
750
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
112
900

750
140

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
112
900

750
140

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 123

SELECTION Parallel Shaft Quadruple Reduction

Nominal Reduction Ratio 160 200

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
11
1500
9.4
160
1200
7.5
1000
6.3
900
5.6
750
4.7
Exact Reduction Ratio
1800
10
1500
8.3
180
1200
6.7
1000
5.6
900
5.0
750
4.2
Exact Reduction Ratio
1800
9.0
1500
7.5
200
1200
6.0
1000
5.0
900
4.5
750
3.8
Horizontal
Dimension
Vertical
Tables
Upright

165.49 159.50 159.92 156.02 158.68 162.11 154.58 157.13 153.94 158.44 158.25 154.04 168.71

7.7
6.4
5.1
4.3
3.9
3.2

10.4
8.7
6.9
5.8
5.2
4.3

12.6
10.5
8.4
7.0
6.3
5.3

16.5
13.7
11.0
9.1
8.2
6.9

17.4
14.5
11.6
9.7
8.7
7.2

25.5
21.3
17.1
14.2
12.8
10.7

26.6
22.2
17.8
14.8
13.3
11.1

42
35
28.1
23.4
21.1
17.5

44
37
29.9
24.9
22.4
18.7

63
53
42
35
31
26.6

71
59
47
39
35
29.7

95
79
64
53
48
40

99
82
66
55
49
41

178.38 173.41 182.48 177.50 180.65 182.13 180.12 179.71 172.48 177.79 174.54 169.14 183.53

6.9
5.8
4.6
3.9
3.5
2.9

9.4
7.9
6.3
5.3
4.7
4.0

10.3
8.6
6.9
5.7
5.2
4.3

14.0
11.7
9.4
7.8
7.1
5.9

16.1
13.4
10.8
9.0
8.1
6.7

20.5
17.1
13.7
11.4
10.3
8.6

25.4
21.2
17.0
14.2
12.8
10.7

32
27.2
21.8
18.2
16.4
13.7

41
34
27.9
23.3
21.0
17.5

53
44
35
29.7
26.7
22.3

62
52
42
35
31
26.4

82
68
54
45
41
34

87
73
58
49
44
36

205.43 206.26 197.71 203.32 207.95 197.74 202.57 193.83 192.43 190.60 192.89 192.86 210.89

6.2
8.0 10.2 12.6 15.0 17.4 24.7 26.6
40
44
59
71
79
5.2
6.7
8.5 10.5 12.5 14.5 20.6 22.2
33
37
49
59
66
4.1
5.4
6.8
8.4 10.0 11.6 16.5 17.8 26.8 29.9
39
47
53
3.5
4.5
5.7
7.0
8.4
9.7 13.8 14.8 22.4 24.9
33
39
44
3.1
4.0
5.1
6.3
7.5
8.7 12.4 13.3 20.2 22.4
30
35
39
2.6
3.4
4.3
5.3
6.3
7.3 10.3 11.1 16.8 18.7 25.0 29.7
33
C-152 C-152 C-152 C-152 C-152 C-152 C-154 C-154 C-154 C-154 C-154 C-154 C-156
C-174 C-174 C-174 C-174 C-174 C-174 C-176 C-176 C-176 C-176 C-176 C-176 C-178
C-188 C-188 C-188 C-188 C-188 C-188 C-190 C-190 C-190 C-190 C-190 C-190

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple
Reduction
Horizontal
Type

160

200
Quadruple
Reduction
Vertical
Type

160

200
Quadruple
Reduction
Upright
Type

160

200

C - 124

1800
1500
1200
1000
900
750

23
22
20
19
18
17

29
28
26
24
23
21

36
34
32
30
29
27

43
41
38
36
35
32

42
40
37
35
33
31

52
49
46
43
41
38

61
58
55
51
49
46

74
71
66
62
59
55

85
81
76
72
69
65

103
98
92
87
84
78

109
105
99
93
90
85

131
126
118
112
108
101

138
134
127
121
117
111

1800
1500
1200
1000
900
750

24
23
21
20
19
17

30
28
26
24
23
21

37
35
33
31
30
27

44
42
39
37
35
33

43
41
38
35
34
31

53
50
46
43
41
38

63
60
56
52
50
47

76
72
67
63
60
56

88
83
78
73
70
66

106
101
94
88
85
79

113
108
101
95
92
86

136
129
121
114
110
103

145
139
131
124
120
113

1800
1500
1200
1000
900
750

23
22
21
19
18
17

29
28
26
24
23
21

39
37
35
33
32
30

43
41
38
36
35
32

42
40
37
35
33
31

52
49
46
43
41
38

62
59
55
51
50
46

74
71
66
62
59
55

85
81
76
72
69
65

104
99
93
87
84
79

110
105
99
94
91
85

132
126
119
112
108
102

SELECTION Parallel Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
152.98 167.85 147.43 151.57 154.53 150.98 160.41 160.41 154.45 157.56 157.56

123
103
82
69
62
51

141
118
94
79
71
59

183
153
123
102
92
77

226
188
151
126
113
95

250
208
167
139
126
105

327
273
219
183
165
137

355
296
237
198
178
149

413
345
276
231
208
173

512
428
343
286
258
215

567
474
380
317
286
238

669
559
448
374
337
281

187.20 180.12 183.73 173.92 171.78 178.43 176.73 176.73 175.45 171.78 171.78

105
88
70
59
53
44

126
105
84
70
63
53

153
127
102
85
77
64

186
155
125
104
94
78

239
199
160
133
120
100

277
231
185
155
139
116

322
269
216
180
162
135

375
313
251
209
189
157

451
377
302
252
227
190

521
435
349
291
262
219

614
513
411
343
309
258

203.11 206.87 199.34 198.63 196.51 191.99 193.01 193.01 190.35 203.02 203.02

93 115 136 173 197 258 295 344 416 442 521
78
96 113 144 164 215 246 287 348 369 435
62
77
91 115 132 172 198 230 279 296 349
52
64
76
96 110 144 165 192 233 247 291
47
58
68
87
99 130 148 173 210 222 262
39
48
57
72
82 108 124 144 175 185 219
C-156 C-156 C-156 C-156 C-156 C-158 C-158 C-158 C-160 C-160 C-160
C-178 C-178 C-178 C-178 C-178

9095 9100 9105 9110 9115 9118 9121 9126 9128

180
175
167
160
155
147

202
196
187
179
174
164

236
229
218
207
201
190

269
262
250
240
234
222

162
155
146
138
133
125

190
183
173
164
159
150

213
204
193
183
177
167

247
237
223
212
205
193

283
272
258
246
239
226

297
288
275
263
256
243

360
351
337
325
317
303

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

11
1800
9.4
1500
160
7.5
1200
6.3
1000
5.6
900
4.7
750
Exact Reduction Ratio
10
1800
8.3
1500
180
6.7
1200
5.6
1000
5.0
900
4.2
750
Exact Reduction Ratio
9.0
1800
7.5
1500
200
6.0
1200
5.0
1000
4.5
900
3.8
750
Horizontal
Dimension
Vertical
Tables
Upright

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
154
149
142
135
131
123

Nominal Reduction Ratio 160 200

360
351
337
325
317
303

393
385
373
361
353
339

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9131 9136
Ratio
r/min
Fans

Without Fan With Fan

480 480
1800 Quadruple
1.00
20
1.00
467 467
1500 Reduction
Horizontal
0.85
30
0.87
449 449
1200
Type
0.70
40
0.73
432 432
1000
160

422 422
900
0.55
50
0.60
200
403 403
750
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
160

900
200
750

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
160
900

750
200

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 125

SELECTION Parallel Shaft Quadruple Reduction

Nominal Reduction Ratio 224 280

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
8.0
1500
6.7
224
1200
5.4
1000
4.5
900
4.0
750
3.3
Exact Reduction Ratio
1800
7.2
1500
6.0
250
1200
4.8
1000
4.0
900
3.6
750
3.0
Exact Reduction Ratio
1800
6.4
1500
5.4
280
1200
4.3
1000
3.6
900
3.2
750
2.7
Horizontal
Dimension
Vertical
Tables
Upright

221.43 224.24 225.60 231.31 236.74 222.15 236.05 221.69 215.61 213.88 212.75 211.77 229.41

5.6
4.7
3.7
3.1
2.8
2.3

7.3
6.1
4.9
4.1
3.7
3.1

8.3
6.9
5.6
4.6
4.2
3.5

256.04

10.8
9.0
7.2
6.0
5.4
4.5

12.3
10.3
8.2
6.9
6.2
5.2

16.8
14.0
11.3
9.4
8.5
7.1

19.4
16.2
13.0
10.8
9.8
8.1

26.5
22.1
17.7
14.8
13.3
11.1

33
27.9
22.4
18.7
16.8
14.0

44
37
29.6
24.7
22.3
18.6

51
43
34
28.8
25.9
21.6

65
54
44
36
33
27.6

70
58
47
39
35
29.5

251.37 260.18 259.14 252.38 254.02 252.17 238.24 252.78 235.08 263.61

6.5
5.4
4.3
3.6
3.3
2.7

10.2
8.5
6.8
5.7
5.1
4.3

278.37

12.0
10.0
8.0
6.7
6.0
5.0

16.0
13.4
10.7
8.9
8.0
6.7

19.8
16.6
13.3
11.1
10.0
8.3

26.0
21.7
17.4
14.5
13.0
10.9

30
25.6
20.5
17.1
15.4
12.8

42
35
28.3
23.6
21.3
17.8

45
38
30
25.5
22.9
19.1

62
52
42
35
31
26.4

63
53
42
35
32
26.7

285.97 296.20 291.13 294.09 290.52 282.55 267.35 278.80 258.13 286.77

5.9
8.7
9.9 12.9 15.6 20.3 25.6
35
39
54
56
4.9
7.3
8.2 10.7 13.0 16.9 21.3 29.6
32
45
47
3.9
5.8
6.6
8.6 10.4 13.5 17.1 23.7 26.4
36
37
3.3
4.9
5.5
7.2
8.7 11.3 14.3 19.8 22.0
30
31
3.0
4.4
4.9
6.5
7.8 10.2 12.8 17.8 19.8 27.1 28.3
2.5
3.7
4.1
5.4
6.5
8.5 10.7 14.9 16.5 22.6 23.6
C-152 C-152 C-152 C-152 C-152 C-152 C-154 C-154 C-154 C-154 C-154 C-154 C-156
C-174 C-174 C-174 C-174 C-174 C-174 C-176 C-176 C-176 C-176 C-176 C-176 C-178
C-188 C-188 C-188 C-188 C-188 C-188 C-190 C-190 C-190 C-190 C-190 C-190

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple
Reduction
Horizontal
Type

224

280
Quadruple
Reduction
Vertical
Type

224

280
Quadruple
Reduction
Upright
Type

224

280

C - 126

1800
1500
1200
1000
900
750

23
22
20
19
18
17

27
25
24
22
21
20

35
33
31
29
28
26

40
38
36
34
32
30

40
38
36
33
32
30

49
47
43
41
39
36

59
56
52
49
47
44

71
67
63
59
56
53

80
77
72
68
66
61

99
94
88
83
80
75

104
99
94
89
86
80

127
121
114
108
104
98

132
127
121
115
112
106

1800
1500
1200
1000
900
750

24
22
21
19
18
17

28
26
24
22
21
20

36
34
32
30
29
27

41
39
36
34
33
31

42
39
36
34
32
30

51
48
44
41
39
36

60
57
53
50
48
44

72
68
64
59
57
53

83
79
74
69
67
62

102
96
90
84
81
76

107
102
96
90
87
81

131
124
116
110
106
99

138
132
125
118
114
107

1800
1500
1200
1000
900
750

23
22
20
19
18
17

27
25
24
22
21
20

38
36
34
32
30
28

40
38
36
34
32
30

41
38
36
33
32
30

50
47
44
41
39
36

59
56
52
49
47
44

71
67
63
59
56
53

81
77
72
68
66
62

99
95
89
83
80
75

104
100
94
89
86
81

127
122
115
108
105
98

SELECTION Parallel Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
234.00 222.00 226.44 227.92 225.12 226.90 230.40 230.40 223.56 232.24 232.24

84
70
56
47
42
35

102
85
68
57
51
43

124
104
83
69
62
52

142
119
95
79
71
60

183
152
122
102
92
76

218
182
146
122
110
91

248
207
166
138
124
104

288
241
193
161
145
121

355
297
238
198
179
149

387
323
259
216
194
162

456
381
305
255
229
191

253.88 252.16 245.68 242.12 257.52 251.60 251.62 251.62 242.56 247.46 247.46

74
62
50
41
37
31

94
79
63
52
47
39

110
92
74
61
55
46

142
118
95
79
71
59

150
126
101
84
75
63

197
165
132
110
99
83

227
189
152
127
114
95

264
221
177
147
133
111

328
274
219
183
165
137

363
303
243
203
182
152

428
357
287
239
215
180

292.50 270.60 276.01 277.82 274.40 276.57 288.00 288.00 275.54 283.08 283.08

67
84 102 117 150 179 199 231 289 318 375
56
70
85
98 125 150 166 193 241 265 313
45
56
68
78 100 120 133 155 193 212 251
37
47
57
65
84 100 111 129 161 177 209
34
42
51
59
75
90 100 116 145 160 188
28.5
35
42
49
63
75
83
97 121 133 157
C-156 C-156 C-156 C-156 C-156 C-158 C-158 C-158 C-160 C-160 C-160
C-178 C-178 C-178 C-178 C-178

9095 9100 9105 9110 9115 9118 9121 9126 9128

174
169
161
154
150
142

190
184
176
168
163
155

222
215
204
195
189
179

247
239
227
216
210
198

149
142
134
127
123
115

183
176
166
158
153
144

200
192
181
172
167
157

232
222
209
199
192
181

257
246
232
220
213
201

275
265
251
239
232
219

322
311
296
283
275
261

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

8.0
1800
6.7
1500
224
5.4
1200
4.5
1000
4.0
900
3.3
750
Exact Reduction Ratio
7.2
1800
6.0
1500
250
4.8
1200
4.0
1000
3.6
900
3.0
750
Exact Reduction Ratio
6.4
1800
5.4
1500
280
4.3
1200
3.6
1000
3.2
900
2.7
750
Horizontal
Dimension
Vertical
Tables
Upright

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
142
137
130
124
120
114

Nominal Reduction Ratio 224 280

322
311
296
283
275
261

366
356
341
328
319
304

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9131 9136
Ratio
r/min
Fans

Without Fan With Fan

443 443
1800 Quadruple
1.00
20
1.00
430 430
1500 Reduction
Horizontal
0.85
30
0.87
411 411
1200
Type
0.70
40
0.73
395 395
1000
224

384 384
900
0.55
50
0.60
280
366 366
750
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
224

900
280
750

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
224

900
280
750

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 127

SELECTION Parallel Shaft Quadruple Reduction

Nominal Reduction Ratio 315 400

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
5.7
1500
4.8
315
1200
3.8
1000
3.2
900
2.9
750
2.4
Exact Reduction Ratio
1800
5.1
1500
4.2
1200
3.4
355
1000
2.8
900
2.5
750
2.1
Exact Reduction Ratio
1800
4.5
1500
3.8
400
1200
3.0
1000
2.5
900
2.3
750
1.9
Horizontal
Dimension
Vertical
Tables
Upright

315.95 324.22 327.89 316.48 324.10 312.22 318.63 308.07 313.18

9.2
7.7
6.2
5.2
4.6
3.9

12.8
10.7
8.6
7.1
6.4
5.4

14.0
11.7
9.4
7.8
7.0
5.9

20.9
17.4
13.9
11.6
10.5
8.7

22.3
18.6
14.9
12.4
11.2
9.3

32
27.0
21.6
18.1
16.3
13.6

34
28.9
23.1
19.3
17.4
14.5

48
40
32
26.8
24.2
20.2

51
43
34
28.8
25.9
21.6

367.08 364.25 364.33 361.96 345.71 350.36 355.25 338.28 359.23

8.0
6.6
5.3
4.4
4.0
3.3

10.3
8.6
6.9
5.7
5.2
4.3

12.6
10.5
8.4
7.0
6.3
5.3

16.3
13.6
10.9
9.1
8.2
6.8

20.9
17.5
14.0
11.7
10.5
8.8

27.1
22.6
18.1
15.1
13.6
11.4

31
25.9
20.7
17.3
15.6
13.0

41
34
27.6
23.0
20.7
17.3

45
37
30
25.1
22.6
18.9

400.89 388.53 421.41 403.56 401.65 401.88 394.72 386.60 383.18

7.3
9.7 10.9 14.6 18.0 23.7 28.0
36
42
6.1
8.1
9.1 12.2 15.0 19.8 23.3
30
35
4.9
6.5
7.3
9.8 12.1 15.8 18.7 24.2 28.3
4.1
5.4
6.1
8.1 10.1 13.2 15.6 20.2 23.6
3.7
4.8
5.5
7.3
9.1 11.9 14.0 18.2 21.2
3.1
4.0
4.6
6.1
7.5
9.9 11.7 15.1 17.7
C-152 C-152 C-154 C-154 C-154 C-154 C-154 C-154 C-156
C-174 C-174 C-176 C-176 C-176 C-176 C-176 C-176 C-178
C-188 C-188 C-190 C-190 C-190 C-190 C-190 C-190

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple
Reduction
Horizontal
Type

315

400
Quadruple
Reduction
Vertical
Type

315

400
Quadruple
Reduction
Upright
Type

315

400

C - 128

1800
1500
1200
1000
900
750

41
39
36
34
33
30

47
45
42
39
37
35

57
54
51
48
46
42

67
64
60
56
54
50

80
76
72
67
65
61

93
89
83
79
76
71

103
99
93
88
85
80

120
115
108
102
99
93

133
128
122
116
113
106

1800
1500
1200
1000
900
750

42
40
37
34
33
31

49
46
42
39
38
35

59
56
52
48
46
43

69
65
61
57
55
51

82
78
73
68
66
61

96
91
85
80
77
72

107
101
95
89
86
81

124
118
110
104
100
94

139
133
125
119
115
108

1800
1500
1200
1000
900
750

41
39
36
34
33
30

48
45
42
39
37
35

58
55
51
48
46
42

67
64
60
56
54
50

81
77
72
68
65
61

94
89
84
79
76
71

104
99
93
88
85
80

121
116
109
103
99
93

SELECTION Parallel Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136

Nominal Reduction Ratio 315 400

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

5.7
1800
4.8
1500
315
3.8
1200
3.2
1000
2.9
900
2.4
750
Exact Reduction Ratio
5.1
1800
4.2
1500
355
3.4
1200
2.8
1000
2.5
900
2.1
750
Exact Reduction Ratio
4.5
1800
3.8
1500
400
3.0
1200
2.5
1000
2.3
900
1.9
750
C-160 C-160 Horizontal
Dimension
Vertical
Tables
Upright

317.35 305.90 299.46 328.33 313.90 316.08 314.53 314.53 298.95 323.52 323.52

60
50
40
33
30
25.2

74
62
49
41
37
31

91
76
60
50
45
38

99
83
66
55
50
41

124
103
83
69
62
52

157
131
105
88
79
66

182
152
122
101
91
76

212
177
142
118
106
89

266
222
178
149
134
112

346.58 349.61 338.53 375.23 370.97 362.44 341.25 341.25 355.99

55
65
45
54
36
43
30
36
27.6
32
23.0 27.4

80
67
53
45
40
33

87
72
58
48
43
36

105
87
70
58
52
44

137
114
92
76
69
57

168
140
112
93
84
70

195
163
131
109
98
82

224
187
150
125
112
94

397.55 389.79 386.90 418.36 423.96 414.22 391.44 391.44 386.24

48
40
32
26.8
24.1
20.1
C-156
C-178

58
70
78
92 120 146 170 207
49
59
65
76 100 122 142 172
39
47
52
61
80
98 114 138
32
39
43
51
67
81
95 115
29.5
35
39
46
60
73
85 104
24.6 29.6
32
38
50
61
71
86
C-156 C-156 C-156 C-156 C-158 C-158 C-158 C-160
C-178 C-178 C-178 C-178

9095 9100 9105 9110 9115 9118 9121 9126 9128

172
166
158
151
147
139

187
181
173
165
160
152

215
207
197
188
182
172

237
229
217
207
201
190

148
142
134
127
122
115

180
172
163
154
150
141

196
188
178
169
164
154

223
214
201
191
185
174

246
235
222
211
204
192

260
250
237
226
219
207

316
304
289
275
267
253

328
274
220
183
165
138

1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Size of Reducer
142
137
130
124
120
113

278
232
186
155
140
117

0QVGU

316
304
289
275
267
253

353
342
327
313
305
289

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9131 9136
Ratio
r/min
Fans

Without Fan With Fan

433 433
1800 Quadruple
1.00
20
1.00
419 419
1500 Reduction
Horizontal
0.85
30
0.87
400 400
1200
Type
0.70
40
0.73
383 383
1000
315

372 372
900
0.55
50
0.60
400
354 354
750
-

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
315
900

750
400

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
315

900
400
750

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 129

SELECTION Parallel Shaft Quadruple Reduction

Nominal Reduction Ratio 450 500

MECHANICAL POWER RATING (kW)

L.Speed
Nominal H.Speed
Size of Reducer
Reduction Shaft Speed Shaft Speed
9015
9025
9030
9035
9040
9045
9050
9055 9060 9065 9070 9075 9080 9085 9090
r/min
r/min
Ratio

Exact Reduction Ratio

1800
4.0
1500
3.3
450
1200
2.7
1000
2.2
900
2.0
750
1.7
Exact Reduction Ratio
1800
3.6
1500
3.0
500
1200
2.4
1000
2.0
900
1.8
750
1.5
Horizontal
Dimension
Vertical
Tables
Upright

451.41

448.40

428.67

431.03

8.3
6.9
5.6
4.6
4.2
3.5

13.2
11.0
8.8
7.3
6.6
5.5

22.2
18.5
14.8
12.4
11.1
9.3

32
27.1
21.7
18.1
16.3
13.6

492.99

518.66

498.04

478.93

7.6
6.4
5.1
4.2
3.8
3.2
C-152
C-174
C-188

11.4
9.5
7.6
6.3
5.7
4.8
C-154
C-176
C-190

19.1
16.0
12.8
10.7
9.6
8.0
C-154
C-176
C-190

29.2
24.4
19.5
16.3
14.7
12.2
C-154
C-176
C-190

THERMAL POWER RATING (kW)

Dimension Selection
Tables
Tables

Speed
Reducer

Nominal H.Speed Number of

Size of Reducer
Reduction Shaft Speed Cooling
9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090
Ratio
r/min
Fans
Quadruple
Reduction
Horizontal
Type

450

500
Quadruple
Reduction
Vertical
Type

450

500
Quadruple
Reduction
Upright
Type

450

500

C - 130

1800
1500
1200
1000
900
750

49
47
43
40
39
36

67
64
59
56
53
50

92
88
82
77
74
69

120
115
108
102
98
92

1800
1500
1200
1000
900
750

50
48
44
41
39
36

69
65
60
56
54
50

94
89
83
78
75
70

123
117
109
103
99
93

1800
1500
1200
1000
900
750

49
47
43
41
39
36

67
64
59
56
53
50

92
88
82
77
74
69

120
115
108
102
98
92

SELECTION Parallel Shaft Quadruple Reduction

Size of Reducer
9095 9100 9105 9110 9115 9118 9121 9126 9128 9131 9136
424.05

431.36

45
37
30
25.1
22.6
18.9

63
52
42
35
31
26.6

C-156
C-178

C-156
C-178

472.69 461.82

82
69
55
46
41
34

108
90
72
60
54
45

C-156 C-158
C-178

Nominal Reduction Ratio 450 500

L.Speed
H.Speed Nominal
Shaft Speed Shaft Speed Reduction
r/min
r/min
Ratio

Exact Reduction Ratio

4.0
1800
3.3
1500
450
2.7
1200
2.2
1000
2.0
900
1.7
750
Exact Reduction Ratio
3.6
1800
3.0
1500
500
2.4
1200
2.0
1000
1.8
900
1.5
750
Horizontal
Dimension
Vertical
Tables
Upright

0QVGU
1.
For marked values, the forced
oil lubrication is required at
continuous operation.
2.
Consult us when the high speed
shaft speed is over 1800r/min.
3.
When the high speed shaft
speed is not shown in the
table, nd it by the interpolation
method.
4.
When the high speed shaft
speed (N) is lower than 750r/min,
nd the mechanical power rating
(PN) according to the following
formula.
PN = P750 X

N
750

5.
Shown in the table are the
ratings for the slow speed shaft.
6.
Refer to C42-C45 for the
allowable radial and axial load on
each shaft.

Temperature

Ambient
Number of H.Speed Nominal
Correction Factor
Cooling Shaft Speed Reduction Temperature
9118 9121 9126 9128 9131 9136
Ratio
r/min
Fans

Without Fan With Fan

256
1800 Quadruple
1.00
20
1.00
246
1500 Reduction
Horizontal
0.85
30
0.87
233
1200
Type
0.70
40
0.73
221
1000
450

214
900
0.55
50
0.60
500
202
750

Size of Reducer
9095 9100 9105 9110 9115
143
138
131
125
121
114

184
178
170
162
157
148

233
225
213
203
196
185

149
143
134
127
123
116

192
184
174
165
160
151

241
231
217
206
199
188

1800 Quadruple
1500 Reduction
Vertical
1200
Type
1000
450

900
500
750

1800 Quadruple
1500 Reduction
Upright
1200
Type
1000
450
900

750
500

0QVGU
1.
Shown in the table are the
ratings for models without a fan
cooling unit and those with a fan.
(-: none fan, 1: with a fan)
2.
The values are applicable
to continuous operation at
ambient temperatures of 20 C
or less. When the temperature
is out of the range, refer to the
temperature correction factor
shown above.
3.
When the high speed shaft
speed is not shown in the table,
nd it by interpolation method.

C - 131

SELECTION Allowable Radial and Axial Loads on Slow Speed

Parallel shaft

Allowable Radial Load (kN)

Sheet 1
L.Speed
Size of Reducer
Shaft
Speed
r/min 9015 9025 9030 9035 9040 9045 9050 9055 9060 9065
250 11.8 17.7 17.7 29.4 29.9 32.4 37.8 46.6 39.7 49.1
160 11.8 17.7 20.1 31.4 32.4 33.8 39.7 48.1 41.7 50.5
Standard 100 11.8 17.7 25.0 35.3 38.7 39.2 47.1 53.5 47.6 54.4
bearing 63 11.8 17.7 26.5 35.3 42.2 47.1 54.9 62.3 58.9 64.3
model
40 11.8 17.7 26.5 35.3 42.2 49.1 54.9 67.7 71.1 78.0
25 11.8 17.7 26.5 35.3 42.2 49.1 54.9 67.7 81.4 95.2
71.1 93.7
250
78.0 94.7
160
Heavy
81.4 98.1
duty 100
bearing 63
81.4 98.1
model
81.4 98.1
40
81.4 98.1
25

Sheet 2

Dimension Selection
Tables
Tables

Speed
Reducer

Applicable to congurations: RL, LR, BL

9070
44.1
46.1
54.4
65.2
79.0
99.1
70.1
77.5
92.2
114.8
117.7
117.7

9075
77.0
89.0
99.0
131.5
141.0
139.5
122.5
137.5
149.5
149.0
148.5
147.0

9080
77.0
89.0
99.0
131.5
141.0
139.5
122.5
137.5
149.5
149.0
148.5
147.0

9085
100.1
108.9
122.1
125.6
125.1
122.6
141.8
132.4
127.0
125.6
125.1
122.6

9090
100.1
108.9
122.1
125.6
125.1
122.6
141.8
132.4
127.0
125.6
125.1
122.6

9095
137.8
145.7
147.6
143.7
137.8
135.4
158.9
151.6
147.6
143.7
137.8
135.4

9100
139.8
157.5
166.3
165.3
164.8
163.3
181.0
174.6
166.8
165.8
165.3
163.8

Applicable to congurations: RR, LL, BR

L.Speed
Size of Reducer
Shaft
Speed
r/min 9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090 9095 9100
8.3
15.2
9.8
21.6 19.1 21.6 22.6 31.4 16.7 28.4 17.2 44.0 44.0 58.4 58.4 97.6 80.4
250
9.8
17.7 12.3 23.1 20.6 23.1 24.0 31.4 18.1 27.0 17.7 55.5 55.5 64.3 64.3 103.0 96.1
160
Standard 100 11.8 17.7 16.7 29.4 26.0 27.5 28.4 35.3 22.1 30.4 25.5 63.5 63.5 74.6 74.6 110.9 105.9
bearing
63 11.8 17.7 21.6 35.3 32.9 35.3 37.3 42.7 33.4 38.3 33.8 95.0 95.0 104.5 104.5 148.1 153.5
model
40 11.8 17.7 26.5 35.3 41.7 43.7 48.6 55.4 45.1 51.5 47.6 129.0 129.0 146.7 146.7 172.2 203.6
25 11.8 17.7 26.5 35.3 42.2 49.1 54.9 67.7 60.8 68.7 67.7 167.0 167.0 171.2 171.2 171.2 215.3
46.1 74.6 40.2 90.0 90.0 114.8 114.8 156.0 150.6
250
52.0 72.1 45.6 103.5 103.5 125.1 125.1 164.8 170.7
160
Heavy
60.3 79.0 59.4 116.0 116.0 140.8 140.8 176.1 187.4
100
duty
bearing 63
81.4 96.6 80.0 152.5 152.5 174.1 174.1 186.9 218.8
model
81.4 98.1 108.9 192.0 192.0 191.8 191.8 193.7 241.8
40
81.4 98.1 117.7 180.5 180.5 171.2 171.2 171.2 214.8
25

Allowable Axial Load (kN)

L.Speed
Size of Reducer
Shaft
Speed
r/min 9015 9025 9030 9035 9040 9045 9050 9055 9060 9065 9070 9075 9080 9085 9090 9095 9100
9.3
11.4 14.7 23.1 26.5 31.4 32.9 31.9 27.0 43.2 28.0 28.0 23.5 23.5 31.4 52.0 45.1
250
9.3
11.4 18.1 23.1 28.4 31.4 33.4 31.9 28.9 43.2 28.4 28.4 27.5 27.5 34.3 53.0 53.0
160
9.3
11.4 24.5 23.1 32.9 31.4 37.3 31.9 34.3 43.2 39.7 39.7 32.9 32.9 43.2 59.4 58.4
Standard 100
bearing
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 52.5 52.5 45.6 45.6 54.0 59.8 81.4
63
model
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 61.4 61.4 63.3 60.3 59.8 59.8 83.4
40
9.3
11.4 26.5 23.1 32.9 31.4 37.3 31.9 49.1 43.2 61.4 61.4 67.7 60.3 59.8 59.8 83.4
25
23.1 34.8 18.6 18.6 56.9 56.9 59.8 59.8 83.4
250
25.0 33.4 21.1 21.1 56.9 56.9 59.8 59.8 83.4
160
Heavy 100
29.4 36.8 27.5 27.5 56.9 56.9 59.8 59.8 83.4
duty
bearing
39.2 43.2 36.3 36.3 56.9 56.9 59.8 59.8 83.4
63
model
39.2 43.2 49.1 49.1 56.9 56.9 59.8 59.8 83.4
40
39.2 43.2 56.9 56.9 56.9 56.9 59.8 59.8 83.4
25

C - 132

SELECTION Allowable Radial and Axial Loads on Slow Speed

Parallel shaft

Overhang Factor
Size of Reducer
9105
192.3
200.6
183.9
178.1
173.6
167.3
213.9
200.6
183.9
178.1
173.6
167.3

9110
167.8
174.1
184.9
190.8
194.7
184.9
250.6
214.8
195.2
190.8
194.7
184.9

9115
222.7
234.9
245.7
303.1
320.8
316.4
316.9
334.5
340.9
333.5
320.8
316.4

9118

9121 9126 9128 9131 9136

391.9
387.5
460.1
448.3

352.7
369.3
449.3
554.8

330.6
341.4
401.2
497.4

315.4
328.6
409.6
534.6

403.2
462.5
572.4
733.8

391.9
430.7
511.1
638.6

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
63 bearing
model
40
25
250
160
Heavy
100
duty
63 bearing
model
40
25

Unit: kN

Size of Reducer
9105
131.5
138.3
146.7
200.1
235.4
304.1
213.4
223.2
236.9
301.7
304.1
304.1

9110
94.2
92.2
101.0
144.7
199.1
272.7
191.3
197.7
210.4
267.8
323.7
323.7

9115
152.5
155.0
167.3
220.7
250.2
353.2
248.7
261.4
274.2
341.9
382.1
374.7

9118

9121 9126 9128 9131 9136

312.0
292.3
373.3
460.1

228.1
244.3
322.7
427.2

197.7
206.0
257.0
348.7

159.4
170.7
250.2
373.3

203.6
260.9
369.3
528.3

190.3
218.8
286.5
398.3

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
bearing
63 model
40
25
250
160
Heavy
100
duty
63 bearing
model
40
25

Overhang Member
Sprocket (Single Row)
Sprocket (Double Row)
Gears

Overhang Factor
1
1.25
1.25

Notes
1. The value shown in the table is allowable radial
load when it is applied to the center of the solid
shaft (except hollow shaft).
Consult us when a load is not in the center.
2. Consult us for the blanks in the table.
3. Consult us when the radial load is applied
upward.
4. In case of double projection shaft (RB,LB,BB)
(1) See sheet1 when the radial load is applied
only to the shaft1.
(2) See sheet2 when the radial load is applied
only to the shaft2.
(3) Consult us when the radial load is applied to
both shafts.
5. Refer to C-6 to check overhang load, and
calculate equivalent load at peak load value.
Be careful under following condition because
large peak load may be generated.
Application: When the inertia is large, such as
for crane driving, slewing, etc.
Motor: inline motor
Connecting method: Sprocket or gear
Consult us when the peak load is larger than
allowable value.

RB

LB
2

Unit: kN

BB
2
Size of Reducer
9105 9110
50.0 50.0
49.5 49.5
54.0 54.0
74.6 74.6
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4
83.4 83.4

9115
76.5
76.5
83.4
83.4
83.4
83.4
83.4
83.4
83.4
83.4
83.4
83.4

9118

9121 9126 9128 9131 9136

119.7
119.7
119.7
119.7

121.6
121.6
121.6
121.6

116.7
121.6
121.6
121.6

91.2
96.6
134.9
144.2

113.3
140.3
191.3
192.3

107.9
122.6
155.5
192.3

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
63 bearing
model
40
25
250
160
100 Heavy
duty
63 bearing
model
40
25

Unit: kN

C - 133

SELECTION Allowable Radial and Axial Loads on Slow Speed

Parallel shaft

Allowable Radial Load (kgf)

Sheet 1
L.Speed
Shaft
Speed
r/min
250
160
Standard
bearing 100
63
model
40
25
250
Heavy 160
duty 100
bearing 63
model
40
25

Applicable to congurations: RL, LR, BL

Size of Reducer
9015
1200
1200
1200
1200
1200
1200

9025
1800
1800
1800
1800
1800
1800

9030
1800
2050
2550
2700
2700
2700

9035
3000
3200
3600
3600
3600
3600

9040
3050
3300
3950
4300
4300
4300

9045
3300
3450
4000
4800
5000
5000

9050
3850
4050
4800
5600
5600
5600

9055
4750
4900
5450
6350
6900
6900

9060
4050
4250
4850
6000
7250
8300
7250
7950
8300
8300
8300
8300

9065
5000
5150
5550
6550
7950
9700
9550
9650
10000
10000
10000
10000

9070
4500
4700
5550
6650
8050
10100
7150
7900
9400
11700
12000
12000

9075
7850
9050
10100
13400
14350
14200
12500
14000
15250
15200
15150
15000

Sheet 2

Dimension Selection
Tables
Tables

Speed
Reducer

L.Speed
Shaft
Speed
r/min
250
160
Standard 100
bearing
63
model
40
25
250
160
Heavy
duty 100
bearing 63
model
40
25

9080
7850
9050
10100
13400
14350
14200
12500
14000
15250
15200
15150
15000

9085
10200
11100
12450
12800
12750
12500
14450
13500
12950
12800
12750
12500

9090
10200
11100
12450
12800
12750
12500
14450
13500
12950
12800
12750
12500

9095
14050
14850
15050
14650
14050
13800
16200
15450
15050
14650
14050
13800

9100
14250
16050
16950
16850
16800
16650
18450
17800
17000
16900
16850
16700

Applicable to congurations: RR, LL, BR

Size of Reducer
9015
850
1000
1200
1200
1200
1200

9025
1550
1800
1800
1800
1800
1800

9030
1000
1250
1700
2200
2700
2700

9035
2200
2350
3000
3600
3600
3600

9040
1950
2100
2650
3350
4250
4300

9045
2200
2350
2800
3600
4450
5000

9050
2300
2450
2900
3800
4950
5600

9055
3200
3200
3600
4350
5650
6900

9060
1700
1850
2250
3400
4600
6200
4700
5300
6150
8300
8300
8300

9065
2900
2750
3100
3900
5250
7000
7600
7350
8050
9850
10000
10000

9070
1750
1800
2600
3450
4850
6900
4100
4650
6050
8150
11100
12000

9075
4500
5650
6450
9700
13150
17000
9150
10550
11800
15550
19550
18400

9080
4500
5650
6450
9700
13150
17000
9150
10550
11800
15550
19550
18400

9085
5950
6550
7600
10650
14950
17450
11700
12750
14350
17750
19550
17450

9090
5950
6550
7600
10650
14950
17450
11700
12750
14350
17750
19550
17450

9095
9950
10500
11300
15100
17550
17450
15900
16800
17950
19050
19750
17450

9100
8200
9800
10800
15650
20750
21950
15350
17400
19100
22300
24650
21900

9070
2850
2900
4050
5350
6260
6260
1900
2150
2800
3700
5000
5800

9075
2850
2900
4050
5350
6260
6260
1900
2150
2800
3700
5000
5800

9080
2400
2800
3350
4650
6450
6900
5800
5800
5800
5800
5800
5800

9085
2400
2800
3350
4650
6150
6150
5800
5800
5800
5800
5800
5800

9090
3200
3500
4400
5500
6100
6100
6100
6100
6100
6100
6100
6100

9095
5300
5400
6050
6100
6100
6100
6100
6100
6100
6100
6100
6100

9100
4600
5400
5950
8300
8500
8500
8500
8500
8500
8500
8500
8500

Allowable Axial Load (kgf)

L.Speed
Shaft
Speed
r/min 9015 9025
250 950 1160
160 950 1160
950 1160
Standard 100
bearing
63 950 1160
model
40 950 1160
25 950 1160
250
160
Heavy 100
duty
bearing
63
model
40
25

C - 134

Size of Reducer
9030
1500
1850
2500
2700
2700
2700

9035
2350
2350
2350
2350
2350
2350

9040
2700
2900
3350
3350
3350
3350

9045
3200
3200
3200
3200
3200
3200

9050
3350
3400
3800
3800
3800
3800

9055
3250
3250
3250
3250
3250
3250

9060
2750
2950
3500
5000
5000
5000
2350
2550
3000
4000
4000
4000

9065
4400
4400
4400
4400
4400
4400
3550
3400
3750
4400
4400
4400

SELECTION Allowable Radial and Axial Loads on Slow Speed

Parallel shaft

Overhang Factor
Size of Reducer
9105
19600
20450
18750
18150
17700
17050
21800
20450
18750
18150
17700
17050

9110
17100
17750
18850
19450
19850
18850
25550
21900
19900
19450
19850
18850

9115
22700
23950
25050
30900
32700
32250
32300
34100
34750
34000
32700
32250

9118 9121 9126 9128 9131 9136

39950
39500
46900
45700

35950
37650
45800
56550

33700
34800
40900
50700

32150
33500
41750
54500

41100
47150
58350
74800

39950
43900
52100
65100

L.Speed
Shaft
Speed
r/min
250
160
Standard
100 bearing
63 model
40
25
250
160 Heavy
100 duty
bearing
63 model
40
25

Unit: kgf

Size of Reducer
9105
13400
14100
14950
20400
24000
31000
21750
22750
24150
30750
31000
31000

9110
9600
9400
10300
14750
20300
27800
19500
20150
21450
27300
33000
33000

9115
15550
15800
17050
22500
25500
36000
25350
26650
27950
34850
38950
38200

9118 9121 9126 9128 9131 9136

31800
29800
38050
46900

23250
24900
32900
43550

20150
21000
26200
35550

16250
17400
25500
38050

20750
26600
37650
53850

19400
22300
29200
40600

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
bearing
63 model
40
25
250
160
Heavy
100 duty
63 bearing
model
40
25

Overhang Member
Sprocket (Single Row)
Sprocket (Double Row)
Gears

Overhang Factor
1
1.25
1.25

Notes
1. The value shown in the table is allowable radial
load when it is applied to the center of the solid
shaft (except hollow shaft).
Consult us when a load is not in the center.
2. Consult us for the blanks in the table.
3. Consult us when the radial load is applied
upward.
4. In case of double projection shaft (RB,LB,BB)
(1) See sheet1 when the radial load is applied
only to the shaft1.
(2) See sheet2 when the radial load is applied
only to the shaft2.
(3) Consult us when the radial load is applied to
both shafts.
5. Refer to C-6 to check overhang load, and
calculate equivalent load at peak load value.
Be careful under following condition because
large peak load may be generated.
Application: When the inertia is large, such as
for crane driving, slewing, etc.
Motor: inline motor
Connecting method: Sprocket or gear
Consult us when the peak load is larger than
allowable value.

RB

LB
2

Unit: kgf

BB
2
Size of Reducer
9105
5100
5050
5500
7600
8500
8500
8500
8500
8500
8500
8500
8500

9110
5100
5050
5500
7600
8500
8500
8500
8500
8500
8500
8500
8500

9115
7800
7800
8500
8500
8500
8500
8500
8500
8500
8500
8500
8500

9118 9121 9126 9128 9131 9136

12200
12200
12200
12200

12400
12400
12400
12400

11900
12400
12400
12400

9300
9850
13750
14700

11550
14300
19500
19600

11000
12500
15850
19600

L.Speed
Shaft
Speed
r/min
250
160
100 Standard
63 bearing
model
40
25
250
160
100 Heavy
duty
63 bearing
model
40
25

Unit: kgf

C - 135

DIMENSIONS Parallel Shaft Double Reduction Horizontal Mounting

9015 9055

FA

X2

Z2

QR

QR

L2
R

FC

FD

Y2

FB

W2

High Speed Shaft

With Fan
Refer to the page D-22 for details.

FY

DP1

DP1

E2

E1

H
L

4- J
D

DP2
G

Dimension Selection
Tables
Tables

Speed
Reducer

[Fig. 1]
Location of oil fill and air vent for Size
9015~9030 with reduction ratio 6.3 or 7.1

K
Y
L

O
P

* Location of oil fill and air vent changes for Size

9015~9030 with reduction ratio 6.3 or 7.1. Refer to Fig. 1.

Size

E1

E2

FY

9015
9025
9030
9035
9040
9045
9050
9055

295
346
406
437
467
506
537
576

160
175
200
219
235
256
255
286

194
227
264
295
306
345
358
397

90
95
110
129
120
141
138.5
171

135
155
160
185
200
220
210
245

270
310
320
370
400
440
420
490

309
346
353

299
339
349
399
431
471
451
521

129
142
154
154
172
172
192
192

70
80
90
90
115
115
116.5
115

22
25
28
28
30
30
32
32

15
19
24
24
28
28
28
28

95
110
120
120
150
150
150
150

440
505
590
640
685
745
775
845

170
195
215
215
255
255
285
285

205
235
265
265
315
315
345
345

300
345
410
460
455
515
542
615

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

100
140
195
215
285
345
415
475

5
7
10
12
16
18
21
28

Fan

High Speed Shaft

Size
9015
9025
9030
9035
9040
9045
9050
9055

QR

W2/Depth

131
146
159
159
174
174
193
193

211
226
269
269
284
284
303
303

80
80
110
110
110
110
110
110

30k6
35k6
40k6
40k6
50k6
50k6
55m6
55m6

M10/22
M12/28
M16/36
M16/36
M16/36
M16/36
M20/42
M20/42

Key
X2
8
10
12
12
14
14
16
16

Y2
4
5
5
5
5.5
5.5
6
6

Z2
7
8
8
8
9
9
10
10

L2
70
70
95
95
95
95
95
95

FA

FB

FC

FD

129
143
169
169
188
188
208
208

125
140
140
140
160
160
160
160

50
50
80
80
80
80
80
80

30
30
52
52
52
52
52
52

Unit: mm
1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions shown in these drawings.

C - 136

4. Refer to the page D -24 for the dimension of optional parts.

5. When fastening the mounting bolt, it is necessary to remove the fan food.

DIMENSIONS Parallel Shaft Double Reduction Horizontal Mounting

9015 9055

Hollow Shaft (Shrink Disk Type)

TU2

TU4
U4

T2

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

9015
9025
9030
9035
9040
9045
9050
9055

V5

V3

V2

Y1

Z1

U1

V1

W1/Depth
M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

T1

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

Double
Reduction

Solid Shaft

Refer to the page D -18 for details.

Parallel

Refer to the page D -18 for details.

W1

Size

X1

T4

9015
9055

V1

U2

V4

T1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal Monoblock

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
65
75
85
90
105
105
115

55
65
75
85
90
105
105
115

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

LL

LB

BL

BR

BB

Nomenclature
Shaft
Arrangement

Size

P H A

Low Speed
Shaft
Type Fan

Nominal
Reduction Ratio

P 2 9015
9025
9030
9035
9040
9045
9050
9055

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) : Without Fan

F : With Fan
(blank):Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9015

9025

9030

9035
9040

9045
9050
9055

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 137

DIMENSIONS Parallel Shaft Double Reduction Horizontal Mounting

9060 9085

FA
FB

X2

Refer to the page D-22 for details.

FY

F
E1

E2

4- J
K

K
DP

Dimension Selection
Tables
Tables

O
P

Speed
Reducer

Y
L

Size

E1

E2

FY

9060
9065
9070
9075
9080
9085

621
667
719
772
812
868

299
338
336
383
378
422

414
460
482
535
556
612

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

183
148
213
178
233
193

578
648
648
718
718
798

212
212
237
237
257
257

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

885
970
1020
1120
1155
1255

310
310
350
350
380
380

380
380
430
430
460
460

615
700
700
800
835
935

DP

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

610
735
860
1110
1240
1500

25
34
38
47
54
68

Fan

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

220
220
245
245
264
264

360
360
385
385
434
434

140
140
140
140
170
170

65m6
65m6
75m6
75m6
85m6
85m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

Key
X2
18
18
20
20
22
22

Y2
7
7
7.5
7.5
9
9

Z2
11
11
12
12
14
14

L2
125
125
125
125
150
150

FA

FB

FC

FD

240
240
274
274
296
296

200
200
225
225
225
225

105
105
105
105
135
135

65
65
65
65
95
95

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
39JGPHCUVGPKPIVJGOQWPVKPIDQNVKVKUPGEGUUCT[VQTGOQXGVJGHCPHQQF

C - 138

W2

High Speed Shaft

With Fan

Z2

Y2

QR

QR

L2
R

FD
FC

4Refer to the page D -14 for dimensions not shown in these drawings.
5Refer to the page D -27 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Double Reduction Horizontal Mounting

9060 9085

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

TU4
U4

T2

T4

V5

Z1

Y1

V4

V3

V2

V1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

U1

T1

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Double
Reduction

TU1

Refer to the page D -18 for details.

Parallel

Solid Shaft

9060
9065
9070
9075
9080
9085

9060
9085

Refer to the page D -18 for details.

W1

Size

Split

X1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

Nomenclature
Shaft
Arrangement

Size

P H D

LL

Low Speed
Shaft
Type Fan

BL

BR

BB

Nominal
Reduction Ratio

P 2 9060
9065
9070
9075
9080
9085

LB

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) : Without Fan

F : With Fan

Size
9060

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9065
9070
9075
9080
9085

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 139

DIMENSIONS Parallel Shaft Double Reduction Horizontal Mounting

9090 9115

FA
C

Z2

Y2

QR

QR

L2
R

FC

FD

FB

X2

W2

High Speed Shaft

With Fan
Refer to the page D-22 for details.

E2

B (90909100)

F
E1

(91059115)

6- J
K1

K2

K3

D
DP

Dimension Selection
Tables
Tables

Speed
Reducer

O
P

Size

E1

E2

K1

K2

K3

9090
9095
9100
9105
9110
9115

1060
1090
1194
1228
1344
1393

428
458
468
493
508
558

640
670
724
758
824
873

345
375
375
410
420
470

375
400
425
450
475
500

750
800
850
900
950
1000

274
286
299
316
321
333

797
847
897
947
997
1047

60
60
70
70
75
75

50
50
55
55
60
60

42
42
48
48
56
56

270
290
300
320
340
350

250
250
280
280
310
310

210
210
240
240
260
260

1440
1500
1610
1680
1810
1910

480
480
560
560
610
610

570
570
650
650
710
710

660
690
735
770
830
880

DP

Wt.
kg

Oil
Qty.
L

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2050
2300
2730
3290
3960
4410

120
140
170
205
240
290

Fan

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

QR

W2/Depth

330
330
375
375
405
405

500
500
585
585
615
615

170
170
210
210
210
210

90m6
90m6
100m6
100m6
110m6
110m6

M24/50
M24/50
M24/50
M24/50
M24/50
M24/50

Key
X2
25
25
28
28
28
28

Y2
9
9
10
10
10
10

Z2
14
14
16
16
16
16

L2
150
150
190
190
190
190

FA

FB

FC

FD

465
465
515
515
565
565

250
250
250
250
250
250

135
135
175
175
175
175

90
90
130
130
130
130

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-16 for dimensions not shown in these drawings.

C - 140

4. Refer to the page D-30 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Double Reduction Horizontal Mounting

9090 9115

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

T2

V3

V2

V1
Y1

Z1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

U1

T1

Double
Reduction

9090
9095
9100
9105
9110
9115

TU1

Parallel

Solid Shaft
Size

9090
9115

Refer to the page D -18 for details.

W1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
15
25
15
25
15
25
17
28
17
28
20
32

X1
45
45
45
50
50
56

TU2 T2
L1
270 844 494
320 859 509
320 934 544
320 949 559
320 1030 610
375 1065 645

U2

V2

V3

350
350
390
390
420
420

193
203
213
223
243
253

190
200
210
220
240
250

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature

LL

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P H D

LR

9090
9095
9100
9105
9110
9115

LB

BL

BR

BB

Nominal
Reduction Ratio

P 2 -

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) : Without Fan

F : With Fan

Size
9090

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9095

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

9100

9105
9110

9115

20

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Split

X1

TU1
U1
L1

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 141

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

9015 9055

FA

X2

Z2

Y2

BH

QR

QR

L2
R

FC

FD

FB

W2

High Speed Shaft

BD

With Fan
Refer to the page D-23 for details.

DP1

F
E1

H
L

4- J
K

K
D
DP2

Speed
Reducer

Dimension Selection
Tables
Tables

Size

E1

9015
9025
9030
9035
9040
9045
9050
9055

338
408
453
484
540
577
609
648

160
175
200
219
235
256
255
286

257
306
343
374
398
437
467
506

90
95
110
129
120
141
138.5
171

135
155
160
185
200
220
210
245

270
310
320
370
400
440
420
490

299
339
349
399
431
471
451
521

70
80
90
90
115
115
116.5
115

22
25
28
28
30
30
32
32

15
19
24
24
28
28
28
28

95
110
120
120
150
150
150
150

485
570
640
690
759
819
848
918

170
195
215
215
255
255
285
285

205
235
265
265
315
315
345
345

345
410
460
510
529
589
615
688

Fan

High Speed Shaft

Size
9015
9025
9030
9035
9040
9045
9050
9055

QR

W2/Depth

130
144
161
161
176
176
194
194

190
204
241
241
256
256
304
304

60
60
80
80
80
80
110
110

25k6
28k6
30k6
30k6
35k6
35k6
40k6
40k6

M10/22
M10/22
M10/22
M10/22
M12/28
M12/28
M16/36
M16/36

X2
8
8
8
8
10
10
12
12

Key
Y2
Z2
4
7
4
7
4
7
4
7
5
8
5
8
5
8
5
8

L2
50
50
70
70
70
70
95
95

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
39JGPHCUVGPKPIVJGOQWPVKPIDQNVKVKUPGEGUUCT[VQTGOQXGVJGHCPHQQF

C - 142

Backstop

FA

FB

FC

FD

111
129
140
150
170
170
172
172

125
125
125
140
140
140
140
140

30
30
50
50
50
50
80
80

10
10
30
22
22
22
52
52

BD

150
150

BH

263
263

DP1 DP2
3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

Wt.
kg

Oil
Qty.
L

105
5
150
8
205 10
225 13
305 19
375 21
445 24
505 29
Unit: mm

4Refer to the page D -13 for dimensions not shown in these drawings.
5Refer to the page D -24 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

9015 9055

Hollow Shaft (Shrink Disk Type)

TU2

TU4
U4

T2

V5

V3

V2

Y1

Z1

U1

V1

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

T1

9015
9025
9030
9035
9040
9045
9050
9055

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

Triple
Reduction

Solid Shaft

Refer to the page D -18 for details.

Parallel

Refer to the page D -18 for details.

W1

Size

X1

T4

9015
9055

V1

U2

V4

T1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal Monoblock

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
55
65
65
75
75
85
85
90
90
105 105
105 105
115 115
Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

LR

Nomenclature
Shaft
Arrangement

Size

P H A

Low Speed
Shaft
Type Option

P 3 9015
9025
9030
9035
9040
9045
9050
9055

LL

LB

BL

BR

BB

Nominal
Reduction Ratio

(blank)
F
B
FB

RL
RR
RB
LR
LL
LB
BL
BR
BB

: Without Fan
: With Fan
: With Backstop
: With Fan & Backstop

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

9015

9025

9030

9035
9040

9045
9050
9055

50

56

63

71

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 143

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

9060 9085

FA
FB

X2

Z2

Y2

BH

Q
QR

QR

L2
R

FC

FD

W2

High Speed Shaft

With Fan

BD

Refer to the page D-23 for details.

E
H

F
E1

E2

4- J
K
G

K
D
DP

Dimension Selection
Tables
Tables

Speed
Reducer

Y
L

O
P

Size

E1

E2

9060
9065
9070
9075
9080
9085

701
747
809
862
932
988

299
338
336
383
378
422

540
586
630
683
725
781

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

155
120
181
146
205
165

578
648
648
718
718
798

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

970
1055
1115
1215
1275
1375

310
310
350
350
380
380

380
380
430
430
460
460

700
785
795
895
955
1055

Fan

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

219
219
244
244
265
265

329
329
354
354
405
405

110
110
110
110
140
140

50k6
50k6
55m6
55m6
65m6
65m6

M16/36
M16/36
M20/42
M20/42
M20/42
M20/42

Key
X2
14
14
16
16
18
18

Y2
5.5
5.5
6
6
7
7

Z2
9
9
10
10
11
11

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
39JGPHCUVGPKPIVJGOQWPVKPIDQNVKVKUPGEGUUCT[VQTGOQXGVJGHCPHQQF

C - 144

L2
95
95
95
95
125
125

Backstop

FA

FB

FC

FD

BD

BH

199
199
221
221
247
247

160
160
160
160
200
200

80
80
80
80
105
105

52
52
52
52
65
65

175
175
190
190
210
210

308
308
330
330
365
365

DP
1"
1"
1"
1"
1"
1"

Wt.
kg

Oil
Qty.
L

660 33
815 38
940 49
1160 59
1350 64
1610 80
Unit: mm

4Refer to the page D -15 for dimensions not shown in these drawings.
5Refer to the page D -27 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

9060 9085

Hollow Shaft (Shrink Disk Type)

TU2

U1
L1

T1

U2

TU4
U4

T2

T4

V5

Z1

Y1

V4

V3

V2

V1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

U1

T1

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Triple
Reduction

TU1

Refer to the page D -18 for details.

Parallel

Solid Shaft

9060
9065
9070
9075
9080
9085

9060
9085

Refer to the page D -18 for details.

W1

Size

Split

X1

TU1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature
P 39060
9065
9070
9075
9080
9085

LL

Low Speed
Shaft
Shaft
Arrangement Type Option

Size

P H D

LR

LB

BL

BR

BB

Nominal
Reduction Ratio

(blank)
F
B
FB

RL
RR
RB
LR
LL
LB
BL
BR
BB

: Without Fan
: With Fan
: With Backstop
: With Fan & Backstop

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9060

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075
9080
9085

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 145

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

9090 9115

FA
FB

Z2

Y2

QR

Q
QR

L2
R

FC

FD

X2

W2

High Speed Shaft

With Fan
Refer to the page D-23 for details.

E2

B (90909100)

F
E1

6- J
K1

K2

K3

D
DP

Dimension Selection
Tables
Tables

O
P

Speed
Reducer

Size

E1

E2

K1

K2

K3

9090
9095
9100
9105
9110
9115

1060
1090
1194
1228
1344
1393

428
458
468
493
508
558

837
867
950
984
1050
1099

345
375
375
410
420
470

375
400
425
450
475
500

750
800
850
900
950
1000

249
254
273
278
283
282

797
847
897
947
997
1047

60
60
70
70
75
75

50
50
55
55
60
60

42
42
48
48
56
56

270
290
300
320
340
350

250
250
280
280
310
310

210
210
240
240
260
260

1440
1500
1610
1680
1810
1910

480
480
560
560
610
610

570
570
650
650
710
710

660
690
735
770
830
880

DP

Wt.
kg

Oil
Qty.
L

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2100
2350
2780
3340
4010
4460

120
155
180
225
260
325

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

QR

W2/Depth

330
330
375
375
405
405

470
470
515
515
575
575

140
140
140
140
170
170

65m6
65m6
75m6
75m6
80m6
80m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

Fan
Key
X2
18
18
20
20
22
22

Y2
7
7
7.5
7.5
9
9

Z2
11
11
12
12
14
14

L2
125
125
125
125
150
150

FA

FB

FC

FD

268
268
289
289
339
339

200
200
225
225
225
225

105
105
105
105
135
135

65
65
65
65
95
95

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3Refer to the page D -16 for dimensions not shown in these drawings.

C - 146

4Refer to the page D -30 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

9090 9115

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

T2

V3

V2

V1
Y1

Z1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

U1

T1

Triple
Reduction

TU1

Parallel

Solid Shaft

9090
9095
9100
9105
9110
9115

9090
9115

Refer to the page D -18 for details.

W1

Size

Split

X1

TU1
U1
L1

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

-G[
X1
45
45
45
50
50
56

Y1
15
15
15
17
17
20

Z1
25
25
25
28
28
32

TU2 T2
L1
270 844 494
320 859 509
320 934 544
320 949 559
320 1030 610
375 1065 645

U2

V2

V3

350
350
390
390
420
420

193 190
203 200
213 210
223 220
243 240
253 250
Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

RB

Nomenclature
Size

P H D

LR

LL

Low Speed
Shaft
Shaft
Arrangement Type Fan

Nominal
Reduction Ratio

P 3 9090
9095
9100
9105
9110
9115

LB

BL

BR

BB

(blank) : Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB
BL
BR
BB

Size
9090

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

9095
9100

9105
9110
9115

45

50

56

63

71

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 147

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

V1

High Speed Shaft

A

QR
Q

T1

L1

L2

E1

E2

U1

W1

Slow Speed Shaft

TU1

Z1

W2

X1

Y1

Z2

Y2

X2

9118 9126

K1

K2

K3

DP

6- J

Dimension Selection
Tables
Tables

Speed
Reducer

Size

E1

E2

K1

K2

K3

9118

1434

608

1140

490

535

1070

338

1117

95

65

56

350

320

260

1990

610

710

900

9121

1585

663

1290

545

580

1160

347

1207

95

70

56

390

300

270

2180

680

780

995

9126

1585

663

1290

545

580

1160

347

1207

95

70

56

390

300

270

2180

680

780

995

High Speed Shaft

Size
9118
9121
9126

QR

W2/Depth

405
440
440

575
650
650

170
210
210

80m6
100m6
100m6

M20/42
M24/50
M24/50

Key
X2
22
28
28

Y2
9
10
10

DP
Z2
14
16
16

L2
150
190
190

Solid Shaft
Size
9118
9121
9126

TU1

T1

U1

V1

W1/Depth

850
935
935

440
465
465

410
470
470

260m6
280m6
300m6

M36/70
M36/70
M36/70

Key
X1
56
63
70

Y1
20
20
22

Z1
32
32
36

L1
375
425
425
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for dimensions not shown in these drawings.

C - 148

Wt.
kg

1 1/2" 5050
1 1/2" 6050
1 1/2" 6350

Oil
Qty.
L
350
470
470

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

9118 9126

RR

RB

LR

LL

LB

BL

BR

BB

Size

Nominal Reduction Ratio

22.4 25

9118

28 31.5 35.5 40

45

50

56

63

71

80

90

9121

9126

(blank) : Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB
BL
BR
BB

H
L

Air Breather

Air Vent

Oil Fill

9118
9121
9126

Triple
Reduction

P 3 -

Nominal
Reduction Ratio

Fan

Parallel

P H D

9118
9126

Shaft
Arrangement

Size

Split

Nomenclature

RL

PARAMAX Horizontal

Standard Shaft Arrangement Conguration

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 149

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

W2

Z1

X1

Y1

Z2

Y2

X2

9128 9136

WL
V1

High Speed Shaft

H
L

W1

Slow Speed 5JCHV

B

TU1

A
U1

QR
T1

R
L2

E1

L1

K1
DP

K2

D
G

G
Y

M
6- J

Y3
L

Dimension Selection
Tables
Tables

Speed
Reducer

Size

9128
9131
9136

1720
1882
1882

680
730
730

1413
1550
1550

330
330
330

600
630
630

E1

1194 1241
1256 1303
1256 1303

K1

K2

Y3

140
140
140

55
60
60

66
66
66

940
940
940

280
280
280

1990
2170
2170

170
200
200

710
850
850

840
980
980

660
660
660

1050
1230
1230

High Speed Shaft

Size
9128
9131
9136

QR

W2/Depth

470
540
540

680
790
790

210
250
250

100m6
130m6
130m6

M24/50
M24/50
M24/50

Key
X2
28
32
32

Y2
10
11
11

DP
Z2
16
18
18

L2
190
225
225

1 1/2" 7250
1 1/2" 9550
1 1/2" 9900

Solid Shaft
Size
9128
9131
9136

TU1

T1

U1

V1

W1/Depth

WL

950
1100
1110

480
550
560

470
550
550

320m6
340m6
360m6

M36/70
M36/70
M36/70

200
215
230

Key
X1
70
80
80

Y1
22
25
25

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for dimensions not shown in these drawings.

C - 150

Z1
36
40
40

Wt.
kg

L1
425
500
500
Unit: mm

Oil
Qty.
L
390
550
540

DIMENSIONS Parallel Shaft Triple Reduction Horizontal Mounting

9128 9136

RR

RB

LR

LL

LB

BL

56

63

71

80

90

9131

9136

50

45

9128

28 31.5 35.5 40

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Nominal Reduction Ratio

22.4 25

Steel
Housing

Size

Triple
Reduction

(blank) : Without Fan

F : With Fan

Parallel

9128
9136

Nominal
Reduction Ratio

Fan

P 3 A RL
RR
RB
LR
LL
LB
BL
BR
BB

Split

Shaft
Arrangement

Size

9128
9131
9136

BB

Consult us each time for delivery date of

reducer type BL, BR, and BB (with double
extended shaft) for size 9131 and 9136.

Nomenclature
P H D

BR

RL

PARAMAX Horizontal

Standard Shaft Arrangement Conguration

Backstop Opposite
(Option)
Side

C - 151

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

9030 9055

BH

Z2

Y2

QR

L2

X2

W2

High Speed Shaft

BD

DP1

E
H

F
E1

H
L

Speed
Reducer

Dimension Selection
Tables
Tables

4- J
K

K
D
DP2

Size

E1

9030
9035
9040
9045
9050
9055

453
484
540
577
609
648

200
219
235
256
255
286

343
374
398
437
467
506

110
129
120
141
138.5
171

160
185
200
220
210
245

320
370
400
440
420
490

349
399
431
471
451
521

90
90
115
115
116.5
115

28
28
30
30
32
32

24
24
28
28
28
28

120
120
150
150
150
150

640
690
759
819
848
918

215
215
255
255
285
285

265
265
315
315
345
345

223
248
279
299
289
324

460
510
529
589
615
688

Backstop

High Speed Shaft

Size
9030
9035
9040
9045
9050
9055

QR

W2/Depth

159
159
175
175
195
195

219
219
235
235
275
275

60
60
60
60
80
80

25k6
25k6
28k6
28k6
30k6
30k6

M10/22
M10/22
M10/22
M10/22
M10/22
M10/22

Key
X2
8
8
8
8
8
8

Y2
4
4
4
4
4
4

Z2
7
7
7
7
7
7

L2
50
50
50
50
70
70

BD

150
150

BH

263
263

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
1"
1"
1"
1"

210
230
310
380
450
510

14
17
25
28
32
40

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D -13 for dimensions not shown in these drawings.

C - 152

4. Refer to the page D -24 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

9030 9055

Hollow Shaft (Shrink Disk Type)

TU2

TU4
U4

T2

330
330
349
391
411
411

160
160
179
181
201
201

170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

9030
9035
9040
9045
9050
9055

V5

V3

V2

Y1

Z1

U1

V1

W1/Depth
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
22
25
25
28
28
32

L1
150
150
150
190
190
185

T1

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
9
14
9
14
9
14
10
16
10
16
11
18

Quadruple
Reduction

Solid Shaft

Refer to the page D -18 for details.

Parallel

Refer to the page D -18 for details.

W1

Size

X1

T4

9030
9055

V1

U2

V4

T1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal Monoblock

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

393
403
448
463
503
528

233
243
268
283
303
323

160
160
180
180
200
205

83
88
98
108
108
123

80
85
95
105
105
120

330
330
360
370
410
410

165
165
180
185
205
205

165
165
180
185
205
205

75
75
85
85
90
90
105 105
105 105
115 115
Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Nomenclature
Size

P H A

RB

LR

Low Speed
Shaft
Shaft
Arrangement Type Option

P 4 9030
9035
9040
9045
9050
9055

LL

LB

BL

BR

BB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) : Without Option

B : With Backstop

Size
9030

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500

9035

9040

9045

9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 153

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

9060 9085

Z2

X2

BH

Y2

Q
QR

L2
R

W2

High Speed Shaft

BD

F
E1

E2

Dimension Selection
Tables
Tables

4- J
K

Speed
Reducer

O
P

DP
G

Y
L

Size

E1

E2

9060
9065
9070
9075
9080
9085

701
747
809
862
932
988

299
338
336
383
378
422

540
586
630
683
725
781

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

126
91
144
109
167
127

578
648
648
718
718
798

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

970
1055
1115
1215
1275
1375

310
310
350
350
380
380

380
380
430
430
460
460

357
392
409
444
461
501

700
785
795
895
955
1055

Backstop

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

221
221
244
244
264
264

301
301
354
354
374
374

80
80
110
110
110
110

35k6
35k6
40k6
40k6
45k6
45k6

M12/28
M12/28
M16/36
M16/36
M16/36
M16/36

Key
X2
10
10
12
12
14
14

Y2
5
5
5
5
5.5
5.5

Z2
8
8
8
8
9
9

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D -15 for dimensions not shown in these drawings.

C - 154

L2
70
70
95
95
95
95

BD

BH

175
175
190
190
210
210

308
308
330
330
365
365

DP
1"
1"
1"
1"
1"
1"

Wt.
kg

Oil
Qty.
L

660 37
815 42
950 56
1170 67
1360 73
1620 90
Unit: mm

4. Refer to the page D -27 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

9060 9085

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

TU4
U4

T2

T4

V5

Z1

Y1

V4

V3

V2

V1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Quadruple
Reduction

Refer to the page D -18 for details.

Parallel

Solid Shaft

9060
9065
9070
9075
9080
9085

9060
9085

Refer to the page D -18 for details.

W1

Size

Split

X1

TU1
U1
L1

Hollow Shaft (Key Type)

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Nomenclature
Size

P H D

RB

Shaft
Arrangement

P 4 9060
9065
9070
9075
9080
9085

LR

Low Speed
Shaft
Type Option

LL

LB

BL

BR

BB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) : Without Option

B : With Backstop
(blank) :Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500

9060

9065

9070

9075
9080
9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 155

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

9090 9115

Z2

X2

Y2

Q
QR

L2
R

W2

High Speed Shaft

E2

B (90909100)

F
E1

6- J
K1

K2

K3

D
DP

Dimension Selection
Tables
Tables

Speed
Reducer

O
P

Size

E1

E2

K1

K2

K3

9090
9095
9100
9105
9110
9115

1060
1090
1194
1228
1344
1393

428
458
468
493
508
558

795
825
901
935
1001
1050

345
375
375
410
420
470

375
400
425
450
475
500

750
800
850
900
950
1000

194
199
208
213
218
217

797
847
897
947
997
1047

60
60
70
70
75
75

50
50
55
55
60
60

42
42
48
48
56
56

270
290
300
320
340
350

250
250
280
280
310
310

210
210
240
240
260
260

1440
1500
1610
1680
1810
1910

480
480
560
560
610
610

570
570
650
650
710
710

517
542
587
612
637
662

660
690
735
770
830
880

DP

Wt.
kg

Oil
Qty.
L

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

QR

W2/Depth

330
330
375
375
405
405

440
440
515
515
545
545

110
110
140
140
140
140

50k6
50k6
60m6
60m6
60m6
60m6

M16/36
M16/36
M20/42
M20/42
M20/42
M20/42

Key
X2
14
14
18
18
18
18

Y2
5.5
5.5
7
7
7
7

Z2
9
9
11
11
11
11

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-16 for dimensions not shown in these drawings.

C - 156

L2
95
95
125
125
125
125

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2150 150
2400 180
2830 220
3390 260
4060 300
4510 365
Unit: mm

4. Refer to the page D-30 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

9090 9115

Hollow Shaft (Shrink Disk Type)

TU2

T1

U2

T2

V3

V2

V1
Y1

Z1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

U1

T1

Quadruple
Reduction

TU1

Parallel

Solid Shaft

9090
9095
9100
9105
9110
9115

9090
9115

Refer to the page D -18 for details.

W1

Size

Split

X1

TU1
U1
L1

Solid Shaft

PARAMAX Horizontal

Slow Speed Shaft

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
15
25
15
25
15
25
17
28
17
28
20
32

X1
45
45
45
50
50
56

TU2 T2
L1
270 844 494
320 859 509
320 934 544
320 949 559
320 1030 610
375 1065 645

U2

V2

V3

350
350
390
390
420
420

193 190
203 200
213 210
223 220
243 240
253 250
Unit: mm

Standard Shaft Arrangement Conguration

RL

RR

Nomenclature
Size

P H D

RB

Shaft
Arrangement

P 4 9090
9095
9100
9105
9110
9115

LR

Low Speed
Shaft
Type

LL

LB

BL

BR

BB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

Size
9090

Nominal Reduction Ratio

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500

9095
9100

9105
9110
9115

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 157

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

W2

U1

QR
T1

E2

L1

L2

E1

W1

Slow Speed Shaft

TU1

A
C

Z1

V1

High Speed Shaft

B

X1

Y1

Z2

X2

Y2

9118 9126

K1

K2

K3

DP

6- J

Dimension Selection
Tables
Tables

Speed
Reducer

Size

E1

E2

K1

K2

K3

9118
9121
9126

1434
1585
1585

608
663
663

1091
1290
1290

490
545
545

535
580
580

1070
1160
1160

278
277
277

1117
1207
1207

95
95
95

65
70
70

56
56
56

350
390
390

320
300
300

260
270
270

1990
2180
2180

610
680
680

710
780
780

697
777
777

900
995
995

DP

Wt.
kg

Oil
Qty.
L

High Speed Shaft

Size
9118
9121
9126

QR

W2/Depth

405
440
440

545
580
580

140
140
140

60m6
65m6
65m6

M20/42
M20/42
M20/42

Key
X2
18
18
18

Y2
7
7
7

Z2
11
11
11

L2
125
125
125

Solid Shaft
Size
9118
9121
9126

TU1

T1

U1

V1

W1/Depth

850
935
935

440
465
465

410
470
470

260m6
280m6
300m6

M36/70
M36/70
M36/70

Key
X1
56
63
70

Y1
20
20
22

Z1
32
32
36

L1
375
425
425

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for dimensions not shown in these drawings.

C - 158

1 1/2" 5050
1 1/2" 6100
1 1/2" 6350

390
530
520

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

9118 9126

RR

RB

LR

LL

LB

BL

BR

BB

Nominal Reduction Ratio

100 112 125 140 160 180 200 224 250 280 315 355 400 450

9118

9121

9126

Size

RL
RR
RB
LR
LL
LB
BL
BR
BB

H
L

Air Breather

Air Vent

9118
9121
9126

Quadruple
Reduction

P 4 -

Nominal
Reduction Ratio

Parallel

P H D

9118
9126

Shaft
Arrangement

Size

Split

Nomenclature

RL

PARAMAX Horizontal

Standard Shaft Arrangement Conguration

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 159

W2

Z1

X1

Y1

Y2

X2

9128 9136

Z2

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

WL
V1

High Speed Shaft

W1

Slow Speed Shaft

H
L

TU1

U1

QR
R

T1

L2

E1

L1

K2

K1
D

DP

6- J

Y3
L

Dimension Selection
Tables
Tables

Speed
Reducer

Size

9128

1720

680

1413

330

600

9131

1882

730

1550

330

630

9136

1882

730

1550

330

630

E1

K1

K2

Y3

1194 1241

140

55

66

940

280

1990

170

710

840

826

660

1050

1256 1303

140

60

66

940

280

2170

200

850

980

856

660

1230

1256 1303

140

60

66

940

280

2170

200

850

980

856

660

1230

Wt.
kg

Oil
Qty.
L

High Speed Shaft

Size
9128
9131
9136

QR

W2/Depth

465
540
540

605
680
680

140
140
140

75m6
75m6
75m6

M20/42
M20/42
M20/42

DP

Key
X2
20
20
20

Y2
7.5
7.5
7.5

Z2
12
12
12

L2
125
125
125

1 1/2" 7400 450

1 1/2" 9600 650
1 1/2" 10000 640

Slow Speed Shaft (Solid)

Size
9128
9131
9136

TU1

T1

U1

V1

W1/Depth

WL

950
1100
1110

480
550
560

470
550
550

320m6
340m6
360m6

M36/70
M36/70
M36/70

200
215
230

Key
X1
70
80
80

Y1
22
25
25

Z1
36
40
40

L1
425
500
500

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Consult us for dimensions not shown in these drawings.

C - 160

DIMENSIONS Parallel Shaft Quadruple Reduction Horizontal Mounting

9128 9136

RR

RB

Nominal
Reduction Ratio

BL

BR

BB

Size

90 100 112 125 140 160 180 200 224 250 280 315 355 400

9131

9136

9128

Nominal Reduction Ratio

80

Size

RL
RR
RB
LR
LL
LB
BL
BR
BB

Steel
Housing

9128
9131
9136

Quadruple
Reduction

P 4 A -

Parallel

P H D

9128
9136

Nomenclature

H
L

Air Breather

Air Vent

Oil Fill

Shaft
Arrangement

LB

LL

Split

LR

RL

PARAMAX Horizontal

Standard Shaft Arrangement Conguration

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 161

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

9015 9055

N1

N2

QR

L2
R

H
L

NP

E2
B

E3

Z2

X2

E1
O

Y2

DP1

W2

High Speed Shaft

Dimension Selection
Tables
Tables

Speed
Reducer

K
DP2

4- J
G

Size

E1

E2

E3

RI

9015
9025
9030
9035
9040
9045
9050
9055

295
346
406
437
467
506
537
576

160
175
200
219
235
256
255
286

194
227
264
295
306
345
358
397

140
155
175
194
205
226
225
256

270
310
320
370
400
440
420
490

195
215
220
245
246
266
270
305

135
155
160
185
200
220
210
245

20
20
25
25
30
30
30
30

35
40
50
50
60
60
60
60

80
87.5
105
120
120
140
140
155

15
19
24
24
28
28
28
28

95
110
120
120
150
150
150
150

440
505
590
640
685
745
775
845

70
75
85
100
100
120
110
135

High Speed Shaft

Size
9015
9025
9030
9035
9040
9045
9050
9055

QR

W2/Depth

131
146
159
159
174
174
193
193

211
226
269
269
284
284
303
303

80
80
110
110
110
110
110
110

30k6
35k6
40k6
40k6
50k6
50k6
55m6
55m6

M10/22
M12/28
M16/36
M16/36
M16/36
M16/36
M20/42
M20/42

Key
X2
8
10
12
12
14
14
16
16

Y2
4
5
5
5
5.5
5.5
6
6

Z2
7
8
8
8
9
9
10
10

L2
70
70
95
95
95
95
95
95

N1

186 25
198.5 23
211 22
211 22
237.5 15
237.5 17.5
257.5 23
257.5 23

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

100
140
195
215
285
345
415
472

5
7
9
12
18
22
22
31

N2

NP

14
12
9
9
2
2
7
7

100
100
100
100
117
117
117
117

230
270
270
320
340
380
360
430

102.5
117.5
132.5
132.5
157.5
157.5
172.5
172.5

260
310
365
396
420
459
490
529

Unit: mm
1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-12 for dimensions not shown in these drawings.

C - 162

4. Refer to the page D-25 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

9015 9055

V5

V4

V3

V2
Z1

T1

U1

V1

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

9015
9025
9030
9035
9040
9045
9050
9055

TU1

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

Refer to the page D-18 for details.

Double
Reduction

Refer to the page D-18 for details.

W1

Parallel

Y1

X1

T4

9015
9055

V1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
55
65
65
75
75
85
85
90
90
105 105
105 105
115 115
Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V A

P 2 9015
9025
9030
9035
9040
9045
9050
9055

Nominal
Reduction Ratio

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

RL
RR

Size

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9015

9025

9030

9035
9040

9045
9050
9055

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 163

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

9060 9085

N
N1

QR

L2
R

P1

NP

E2

E3

E1
O

Y2

X2

Z2

DP1

W2

RI

High Speed Shaft

K

Dimension Selection
Tables
Tables

Speed
Reducer

DP2

K
D

4- J
G

Y
L

* Refer to footnote 3.

Size

E1

E2

E3

RI

N1

NP

P1

9060
9065
9070
9075
9080
9085

621
667
719
772
812
868

299
338
336
383
378
422

414
460
482
535
556
612

251
290
283
330
325
369

530
600
600
670
670
750

282
317
317
352
352
392

265
300
300
335
335
375

35
35
40
40
40
40

35
35
40
52
52
52

160
175
175
190
190
215

35
35
42
42
42
42

180
180
215
220
220
220

885
970
1020
1120
1155
1255

140
175
155
195
170
210

277.5
277.5
302.5
302.5
322.5
322.5

35
38
38
40
45
40

117
117
117
117
117
117

460
530
520
590
590
670

190
190
215
215
230
230

223
223
253
253
283
283

564
610
657
710
750
806

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

220
220
245
245
264
264

360
360
385
385
434
434

140
140
140
140
170
170

65m6
65m6
75m6
75m6
85m6
85m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

Key
X2
18
18
20
20
22
22

Y2
7
7
7.5
7.5
9
9

DP1 DP2
Z2
11
11
12
12
14
14

L2
125
125
125
125
150
150

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

Wt.
kg

Oil
Qty.
L

610
735
860
1110
1240
1500

25
32
39
49
54
71

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with visible gauge. Refer to page D-28.

C - 164

4Refer to the page D-14 for dimensions not shown in these drawings.
5Refer to the page D-28 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

9060 9085

V5

Z1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

T1

9060
9065
9070
9075
9080
9085

TU1

Hollow Shaft (Shrink Disk Type)

-G[
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Double
Reduction

Solid Shaft

Refer to the page D-18 for details.

Parallel

Refer to the page D-18 for details.

W1

Size

V4

V3

V2

V1
X1

T4

9060
9085

Y1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V D

P 2 9060
9065
9070
9075
9080
9085

Nominal
Reduction Ratio

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

RL
RR

Size
9060

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9065
9070
9075
9080
9085

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 165

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

9090 9115

N1

P
H

QR

L2
R

P1

DP2

E2

Z2

X2

E1
O

E3

Y2

E2

W2

RI

High Speed Shaft

Dimension Selection
Tables
Tables

Speed
Reducer

K
G

4- J

K
Y

L
DP1
Size

E1

E2

E3

RI

N1

P1

9090
9095
9100
9105
9110
9115

1060
1090
1194
1228
1344
1393

410
440
450
485
500
550

640
670
724
758
824
873

345
375
375
410
420
470

750
800
850
900
950
1000

421
446
471
496
521
546

430
430
500
500
500
500

60
60
70
70
75
75

50
50
55
55
60
60

215
235
235
260
265
280

42
42
48
48
56
56

180
200
200
220
220
250

1440
1500
1610
1680
1810
1910

130
140
150
160
170
180

50
50
60
60
55
55

630
680
710
760
800
850

285
285
325
325
355
355

394
394
443
443
475
475

975
1005
1095
1130
1240
1290

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2070
2330
2820
3300
3950
4470

90
120
140
175
200
255

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

QR

W2/Depth

330
330
375
375
405
405

500
500
585
585
615
615

170
170
210
210
210
210

90m6
90m6
100m6
100m6
110m6
110m6

M24/50
M24/50
M24/50
M24/50
M24/50
M24/50

Key
X2
25
25
28
28
28
28

Y2
9
9
10
10
10
10

Z2
14
14
16
16
16
16

9090 ~ 9115 are equipped with motor driven pumps. For details consult us.

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with visible. Refer to page D-31.

C - 166

L2
150
150
190
190
190
190

Unit: mm

4. Refer to the page D -16 for dimensions not shown in these drawings.
5. Refer to the page D -31 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Double Reduction Vertical Mounting

9090 9115

V3

V2

V1

Z1

T1

U1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

9090
9095
9100
9105
9110
9115

TU1

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

Double
Reduction

Refer to the page D-18 for details.

W1

Parallel

X1

9090
9115

Y1

T2

U2

TU2
T1

TU1
U1
L1

Split

Hollow Shaft (Shrink Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

X1
45
45
45
50
50
56

Key
Y1
Z1
15
25
15
25
15
25
17
28
17
28
20
32

TU2 T2
L1
270 844 494
320 859 509
320 934 544
320 949 559
320 1030 610
375 1065 645

U2

V2

V3

350
350
390
390
420
420

193
203
213
223
243
253

190
200
210
220
240
250

Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V D

P 2 9090
9095
9100
9105
9110
9115

Nominal
Reduction Ratio

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

RL
RR

Size
9090

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9095
9100

9105
9110
9115

20

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 167

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

9015 9055

N1

QR

L2
R

H
L

NP
194 (9015 Only)
E2
B

E3

E1
O

Z2

X2

Y2

M1

M2

DP2

W2

M1

High Speed Shaft

Dimension Selection
Tables
Tables

Speed
Reducer

K
DP1

4- J
G

Size

E1

E2

E3

RI

M1

M2

9015
9025
9030
9035
9040
9045
9050
9055

338
408
453
484
540
577
609
648

160
175
200
219
235
256
255
286

257
306
343
374
398
437
467
506

140
155
175
194
205
226
225
256

270
310
320
370
400
440
420
490

195
215
220
245
260
277
270
305

135
155
160
185
200
220
210
245

20
20
25
25
30
30
30
30

35
40
50
50
60
60
60
60

80
87.5
105
120
120
140
140
155

15
19
24
24
28
28
28
28

95
110
120
120
150
150
150
150

485
570
640
690
759
819
848
918

70
75
85
100
100
120
110
135

80
90
50
75
70
90
83
118

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

105
150
205
225
305
375
445
505

6
8
10
14
18
22
25
35

High Speed Shaft

Size
9015
9025
9030
9035
9040
9045
9050
9055

QR

W2/Depth

130
144
161
161
176
176
194
194

190
204
241
241
256
256
304
304

60
60
80
80
80
80
110
110

25k6
28k6
30k6
30k6
35k6
35k6
40k6
40k6

M10/22
M10/22
M10/22
M10/22
M12/28
M12/28
M16/36
M16/36

Key
X2
8
8
8
8
10
10
12
12

Y2
4
4
4
4
5
5
5
5

Z2
7
7
7
7
8
8
8
8

L2
50
50
70
70
70
70
95
95

N1

NP

186
25 100
198.5 23 100
211
22 100
211
22 100
228.5 15 100
228.5 17.5 100
248.5 23 100
248.5 23 100

230
270
270
320
340
380
360
430

102.5
117.5
132.5
132.5
157.5
157.5
172.5
172.5

305
375
415
446
494
533
563
602

Unit: mm
1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3Refer to the page D-13 for dimensions not shown in these drawings.

C - 168

4Refer to the page D-25 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

9015 9055

V5

V4

V3

V2
Z1

Y1

V1

V1

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

U1

T1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

Triple
Reduction

TU1

Refer to the page D-18 for details.

Parallel

Refer to the page D-18 for details.

Solid Shaft

9015
9025
9030
9035
9040
9045
9050
9055

T4

9015
9055

X1

W1

Size

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
65
75
85
90
105
105
115

55
65
75
85
90
105
105
115

Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V A

P 3 9015
9025
9030
9035
9040
9045
9050
9055

Nominal
Reduction Ratio

RL
RR

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

9015

9025

9030

9035
9040

56

63

71

9045
9050

50

9055

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 169

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

9060 9085

N1

Q
QR

L2
R

P1

NP

E2

E3

W2

RI

M1

E1
O

Z2

X2

Y2

M1

M2

DP1

High Speed Shaft

K

Dimension Selection
Tables
Tables

Speed
Reducer

DP2

4- J
G

K
Y
L

* Refer to footnote 3.

Size

E1

E2

E3

RI

M1

M2

N1

NP

P1

9060
9065
9070
9075
9080
9085

701
747
809
862
932
988

299
338
336
383
378
422

540
586
630
683
725
781

251
290
283
330
325
369

530
600
600
670
670
750

282
317
317
352
352
392

265
300
300
335
335
375

35
35
40
40
40
40

35
35
40
52
52
52

160
175
175
190
190
215

35
35
42
42
42
42

180
180
215
220
220
220

970
1055
1115
1215
1275
1375

140
175
155
195
170
210

118
153
128
163
140
180

277.5
277.5
302.5
302.5
322.5
322.5

35
38
38
40
45
40

117
117
117
117
117
117

460
530
520
590
590
670

190
190
215
215
230
230

223
223
253
253
283
283

649
695
752
805
870
926

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

219
219
244
244
265
265

329
329
354
354
405
405

110
110
110
110
140
140

50k6
50k6
55m6
55m6
65m6
65m6

M16/36
M16/36
M20/42
M20/42
M20/42
M20/42

Key
X2
14
14
16
16
18
18

Y2
5.5
5.5
6
6
7
7

DP1 DP2
Z2
9
9
10
10
11
11

L2
95
95
95
95
125
125

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

Wt.
kg

Oil
Qty.
L

660
815
940
1160
1350
1610

28
35
44
56
57
79

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with visible gauge. Refer to page D-28.

C - 170

4Refer to the page D-15 for dimensions not shown in these drawings.
5Refer to the page D-28 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

9060 9085

V5

V3

V4

T4

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

U1

Hollow Shaft (Key Type)

T1

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Triple
Reduction

TU1

Refer to the page D-18 for details.

Parallel

Refer to the page D-18 for details.

Solid Shaft

9060
9065
9070
9075
9080
9085

TU4

Z1

V2

V1
X1

W1

Size

U4

T2

9060
9085

Y1

TU2

U2

T1

TU1

Hollow Shaft (Key Type)

Split

U1
L1

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Unit: mm

Standard Arrangement Configuration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V D

P 3 9060
9065
9070
9075
9080
9085

Nominal
Reduction Ratio

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

RL
RR

Size
9060

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075
9080
9085

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 171

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

9090 9115

* Refer to footnote 3.

N1

P
H

QR

L2
R

P1

E2

E2

DP2

E1
O

E3

Y2

X2

Z2

W2

RI

Dimension Selection
Tables
Tables

Speed
Reducer

K
G

High Speed Shaft

4- J

K
Y

L
DP1

Size

E1

E2

E3

RI

N1

P1

9090
9095
9100
9105
9110
9115

1060
1090
1194
1228
1344
1393

410
440
450
485
500
550

837
867
950
984
1050
1099

345
375
375
410
420
470

750
800
850
900
950
1000

421
446
471
496
521
546

430
430
500
500
500
500

60
60
70
70
75
75

50
50
55
55
60
60

215
235
235
260
265
280

42
42
48
48
56
56

180
200
200
220
220
250

1440
1500
1610
1680
1810
1910

130
140
150
160
170
180

50
50
60
60
55
55

630
680
710
760
800
850

285
285
325
325
355
355

394
394
443
443
475
475

975
1005
1095
1130
1240
1290

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2120
2380
2870
3350
4000
4520

90
120
140
175
200
255

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

QR

W2/Depth

330
330
375
375
405
405

470
470
515
515
575
575

140
140
140
140
170
170

65m6
65m6
75m6
75m6
80m6
80m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

Key
X2
18
18
20
20
22
22

Y2
7
7
7.5
7.5
9
9

Z2
11
11
12
12
14
14

9090 ~ 9115 are equipped with motor driven pumps. For details consult us.

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with oil gauge. Refer to the page D-31.

C - 172

L2
125
125
125
125
150
150

Unit: mm

4. Refer to the page D -16 for dimensions not shown in these drawings.
5. Refer to the page D -31 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Triple Reduction Vertical Mounting

9090 9115

V3

V2

V1

Z1

T1

U1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

9090
9095
9100
9105
9110
9115

TU1

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

Triple
Reduction

Refer to the page D-18 for details.

W1

Parallel

X1

9090
9115

Y1

T2

U2

TU2
T1

TU1
U1
L1

Split

Hollow Shaft (Shrink Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Key
Y1
Z1
15
25
15
25
15
25
17
28
17
28
20
32

X1
45
45
45
50
50
56

TU2 T2
L1
270 844 494
320 859 509
320 934 544
320 949 559
320 1030 610
375 1065 645

U2

V2

V3

350
350
390
390
420
420

193
203
213
223
243
253

190
200
210
220
240
250

Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V D

P 3 9090
9095
9100
9105
9110
9115

Nominal
Reduction Ratio

RL
RR

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

Size
9090

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

9095
9100

9105
9110
9115

45

50

56

63

71

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 173

DIMENSIONS Parallel Shaft Quadruple Reduction Vertical Mounting

9030 9055

X
C

N1

QR

L2
R

H
L

NP

E2
B

E3

Z2

Y2

X2

W2

M1

E1

M1

M2

DP2

High Speed Shaft

Dimension Selection
Tables
Tables

Speed
Reducer

K
DP1

4- J
G

Size

E1

E2

E3

RI

9030
9035
9040
9045
9050
9055

453
484
540
577
609
648

200
219
235
256
255
286

343
374
398
437
467
506

175
194
205
226
225
256

320
370
400
440
420
490

220
245
260
277
270
305

160
185
200
220
210
245

25
25
30
30
30
30

50
50
60
60
60
60

105
120
120
140
140
155

24
24
28
28
28
28

120
120
150
150
150
150

640
690
759
819
848
918

M1

M2

85 50
100 75
100 70
120 90
110 83
135 118

High Speed Shaft

Size
9030
9035
9040
9045
9050
9055

QR

W2/Depth

159
159
175
175
195
195

219
219
235
235
275
275

60
60
60
60
80
80

25k6
25k6
28k6
28k6
30k6
30k6

M10/22
M10/22
M10/22
M10/22
M10/22
M10/22

Key
X2
8
8
8
8
8
8

Y2
4
4
4
4
4
4

Z2
7
7
7
7
7
7

L2
50
50
50
50
70
70

N1

NP

211 22 100 270

211 22 100 320
228.5 15 100 340
228.5 17.5 100 380
248.5 23 100 360
248.5 23 100 430

DP1

DP2

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
1"
1"
1"
1"

3/4"
3/4"
1"
1"
1"
1"

210
230
310
380
450
510

10
14
17
21
23
33

132.5
132.5
157.5
157.5
172.5
172.5

63
63
79
79
79
79

415
446
494
533
563
602

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3Refer to the page D-13 for dimensions not shown in these drawings.

C - 174

4. Refer to the page D-25 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Quadruple Reduction Vertical Mounting

9030 9055

V5

V4

V3

V2
Z1

Y1

V1

V1

W1/Depth

330
330
349
391
411
411

160
160
179
181
201
201

170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
22
25
25
28
28
32

L1
150
150
150
190
190
185

U1

T1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
9
14
9
14
9
14
10
16
10
16
11
18

Quadruple
Reduction

TU1

Refer to the page D-18 for details.

Parallel

Refer to the page D-18 for details.

Solid Shaft

9030
9035
9040
9045
9050
9055

T4

9030
9055

X1

W1

Size

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

393
403
448
463
503
528

233
243
268
283
303
323

160
160
180
180
200
205

83
88
98
108
108
123

80
85
95
105
105
120

330
330
360
370
410
410

165
165
180
185
205
205

165
165
180
185
205
205

75
85
90
105
105
115

75
85
90
105
105
115

Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature
Size

P V A

Low Speed
Shaft
Shaft
Arrangement Type

P 4 9030
9035
9040
9045
9050
9055

Nominal
Reduction Ratio

RL
RR

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size
9030

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500

9035

9040

9045

9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 175

DIMENSIONS Parallel Shaft Quadruple Reduction Vertical Mounting

9060 9085

N1

QR

L2
R

P1

NP

E2

E3

Z2

X2

W2

RI

M1

E1
O

Y2

M1

M2

DP1

High Speed Shaft

K

Dimension Selection
Tables
Tables

Speed
Reducer

DP2

4- J
G

K
D

Y
L
* Refer to footnote 3.

Size

E1

E2

E3

RI

M1

M2

N1

NP

P1

9060
9065
9070
9075
9080
9085

701
747
809
862
932
988

299
338
336
383
378
422

540
586
630
683
725
781

251
290
283
330
325
369

530
600
600
670
670
750

282
317
317
352
352
392

265
300
300
335
335
375

35
35
40
40
40
40

35
35
40
52
52
52

160
175
175
190
190
215

35
35
42
42
42
42

180
180
215
220
220
220

970
1055
1115
1215
1275
1375

140
175
155
195
170
210

118
153
128
163
140
180

277.5
277.5
302.5
302.5
322.5
322.5

35
38
38
40
45
40

117
117
117
117
117
117

460
530
520
590
590
670

190
190
215
215
230
230

213
213
233
233
268
268

92
92
109
109
126
126

649
695
752
805
870
926

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

221
221
244
244
264
264

301
301
354
354
374
374

80
80
110
110
110
110

35k6
35k6
40k6
40k6
45k6
45k6

M12/28
M12/28
M16/36
M16/36
M16/36
M16/36

Key
X2
10
10
12
12
14
14

Y2
5
5
5
5
5.5
5.5

DP1 DP2
Z2
8
8
8
8
9
9

L2
70
70
95
95
95
95

1"
1"
1"
1"
1"
1"

1"
1"
1"
1"
1"
1"

Wt.
kg

Oil
Qty.
L

660
815
950
1170
1360
1620

32
40
53
67
65
89

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with visible gauge. Refer to page D-28.

C - 176

4Refer to the page D-15 for dimensions not shown in these drawings.
5Refer to the page D-28 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Quadruple Reduction Vertical Mounting

9060 9085

V5

Z1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

TU1

9060
9065
9070
9075
9080
9085

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Quadruple
Reduction

Solid Shaft

Refer to the page D-18 for details.

Parallel

Refer to the page D-18 for details.

W1

Size

V4

V3

V2

V1
X1

T4

9060
9085

Y1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125 123
145 143
145 143
150 148
165 163
175 173
Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature
Size

P V D

Shaft
Arrangement

P 4 9060
9065
9070
9075
9080
9085

Low Speed
Shaft
Type

Nominal
Reduction Ratio

RL
RR

(blank) :Solid Shaft

Size
T : Hollow Shaft
(Shrink Disk type) 9060
K : Hollow Shaft (Key type) 9065
9070

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500

9075
9080
9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 177

DIMENSIONS Parallel Shaft Quadruple Reduction Vertical Mounting

9090 9115

* Refer to footnote 3.

N1

P
H

Q
QR

L2
R

P1

NP

DP2

E3

E2

Z2

X2

E4

O
M

E1

Y2

C1

W2

RI

High Speed Shaft

Dimension Selection
Tables
Tables

Speed
Reducer

K
D

4- J

L
DP1
Size

C1

E1

E2

E3

E4

RI

NP

N1

P1

9090
9095
9100
9105
9110
9115

1060
1090
1194
1228
1344
1393

410
440
450
485
500
550

795
825
901
935
1001
1050

837
867
950
984
1050
1099

345
375
375
410
420
470

750
800
850
900
950
1000

421
446
471
496
521
546

449
474
499
524

430
430
500
500
500
500

60
60
70
70
75
75

50
50
55
55
60
60

215
235
235
260
265
280

42
42
48
48
56
56

180
200
200
220
220
250

1440
1500
1610
1680
1810
1910

130
140
150
160
170
180

381
381
421
421

137
137
137
137

50
50
60
60
55
55

630
680
710
760
800
850

285
285
325
325
355
355

367
367
409
409
442
442

142
142
162
162
162
162

975
1005
1095
1130
1240
1290

High Speed Shaft

Size
9090
9095
9100
9105
9110
9115

QR

W2/Depth

330
330
375
375
405
405

440
440
515
515
545
545

110
110
140
140
140
140

50k6
50k6
60m6
60m6
60m6
60m6

M16/36
M16/36
M20/42
M20/42
M20/42
M20/42

Key
X2
14
14
18
18
18
18

Y2
5.5
5.5
7
7
7
7

Z2
9
9
11
11
11
11

9110 ~ 9115 are equipped with motor driven pumps. For details consult us.

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Shaft arrangement RR is equipped with oil gauge. Refer to the page D-31.

C - 178

L2
95
95
125
125
125
125

DP1

DP2

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"

2170
2430
2920
3400
4050
4570

110
140
170
210
240
295

Unit: mm

4. Refer to the page D-16 for dimensions not shown in these drawings.
5. Refer to the page D -31 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Quadruple Reduction Vertical Mounting

9090 9115

V3

V2

V1

Z1

T1

U1

V1

W1/Depth

650
700
740
740
770
830

350
350
390
390
420
420

300
350
350
350
350
410

180m6
190m6
200m6
220m6
220m6
240m6

M30/60
M30/60
M30/60
M30/60
M30/60
M30/60

9090
9095
9100
9105
9110
9115

TU1

Hollow Shaft (Shrink Disk Type)

Solid Shaft
Size

Quadruple
Reduction

Refer to the page D-18 for details.

W1

Parallel

X1

9090
9115

Y1

T2

U2

TU2
T1

TU1
U1
L1

Split

Hollow Shaft (Shrink Type)

Vertical

Solid Shaft

PARAMAX

Slow Speed Shaft

Key
Y1
Z1
15
25
15
25
15
25
17
28
17
28
20
32

X1
45
45
45
50
50
56

TU2 T2
L1
270 844 494
320 859 509
320 934 544
320 949 559
320 1030 610
375 1065 645

U2

V2

V3

350
350
390
390
420
420

193
203
213
223
243
253

190
200
210
220
240
250

Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P V D

P 4 9090
9095
9100
9105
9110
9115

Nominal
Reduction Ratio

RL
RR

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)

Size
9090

Nominal Reduction Ratio

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450

9095
9100

9105
9110

9115

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 179

DIMENSIONS Parallel Shaft Double Reduction Upright Mounting

9015 9055

QR
FC

Y3

FA
FB

X2

Z2

Y2

FD

W2

H2

High Speed Shaft

With Fan
Refer to the page D-22 for details.

QR
Q
4- J2
K3

H
L

H1
K3

Y4
L

R
L2

4- J1

Dimension Selection
Tables
Tables

K2

K1

K1

Y1

Speed
Reducer

Y2
E1
F

K2
P

Size

9015
9025
9030
9035
9040
9045
9050
9055

296
347
407
438
468
507
538
577

160
175
200
219
235
256
255
286

194 90 135
227 95 155
264 110 160
295 129 185
306 120 200
345 141 220
358 138.5 210
397 171 245

E1
270
310
320
370
400
440
420
490

298 70
338 80
348 90
398 90
430 115
470 115
450 116.5
520 115

H1

H2

J1

J2

K1

K2

K3

Y1

Y2

Y3

Y4

50
55
60
60
75
75
75
75

22
25
28
28
30
30
32
32

15
19
24
24
28
28
28
28

15
19
24
24
28
28
28
28

70
75
85
100
100
120
110
135

35
40
50
50
60
60
60
60

95
110
120
120
150
150
150
150

440
505
590
640
685
745
775
845

205
235
265
265
315
315
345
345

170
195
215
215
255
255
285
285

180
210
200
250
260
300
280
350

170
195
215
215
255
255
285
285

300
345
410
460
455
515
542
615

High Speed Shaft

Size
9015
9025
9030
9035
9040
9045
9050
9055

QR

W2/Depth

131
146
159
159
174
174
193
193

211
226
269
269
284
284
303
303

80
80
110
110
110
110
110
110

30k6
35k6
40k6
40k6
50k6
50k6
55m6
55m6

M10/22
M12/28
M16/36
M16/36
M16/36
M16/36
M20/42
M20/42

DP

Fan
Key
X2
8
10
12
12
14
14
16
16

Y2
4
5
5
5
5.5
5.5
6
6

Z2
7
8
8
8
9
9
10
10

L2
70
70
95
95
95
95
95
95

FA

FB

FC

FD

129
143
169
169
188
188
208
208

125
140
140
140
160
160
160
160

50
50
80
80
80
80
80
80

30
30
52
52
52
52
52
52

DP

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

100
140
195
215
285
345
415
475

9
13
16
22
29
36
36
47
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Always remove fan hood when tightening mounting bolt.

C - 180

4. Refer to the page D-12 for dimensions not shown in these drawings.
5. Refer to the page D-26 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Double Reduction Upright Mounting

9015 9055

V5

V4

V3

V2
Z1

T1

U1

V1

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

9015
9025
9030
9035
9040
9045
9050
9055

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

Solid Shaft

Size

Refer to the page D-18 for details.

Double
Reduction

Refer to the page D-18 for details.

W1

Parallel

Y1

X1

T4

9015
9055

V1

U4

T2

TU4

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
65
75
85
90
105
105
115

55
65
75
85
90
105
105
115

Unit: mm

Standard Arrangement Conguration

RL

RR

RB

LR

Nomenclature
Shaft
Arrangement

Size

P W A

LL

Low Speed
Shaft
Type Fan

BL

BR

BB

Nominal
Reduction Ratio

P 2 9015
9025
9030
9035
9040
9045
9050
9055

LB

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) : Without Fan

F : With Fan
(blank) :Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9015

9025

9030

9035
9040

9045
9050
9055

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 181

DIMENSIONS Parallel Shaft Double Reduction Upright Mounting

9060 9085

QR

O
P

FA
FB

X2

Z2

Y2

FC
FD

W2

High Speed Shaft

With Fan
H

Refer to the page D-22 for details.

QR
Q

Dimension Selection
Tables
Tables

Speed
Reducer

Y
L

4- J

R
L2

E1
F
DP

Size

E1

9060
9065
9070
9075
9080
9085

622
668
720
773
813
869

299
338
336
383
378
422

414
460
482
535
556
612

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

577
647
647
717
717
797

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

885
970
1020
1120
1155
1255

310
310
350
350
380
380

380
380
430
430
460
460

133
133
138
138
169
169

615
700
700
800
835
935

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

220
220
245
245
264
264

360
360
385
385
434
434

140
140
140
140
170
170

65m6
65m6
75m6
75m6
85m6
85m6

M20/42
M20/42
M20/42
M20/42
M20/42
M20/42

Fan
Key
X2
18
18
20
20
22
22

Y2
7
7
7.5
7.5
9
9

Z2
11
11
12
12
14
14

L2
125
125
125
125
150
150

FA

FB

FC

FD

240
240
274
274
296
296

200
200
225
225
225
225

105
105
105
105
135
135

65
65
65
65
95
95

DP
1"
1"
1"
1"
1"
1"

Wt.
kg

Oil
Qty.
L

610 53
735 67
860 84
1110 100
1240 109
1500 137
Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Always remove fan hood when tightening mounting bolt.

C - 182

4. Refer to the page D-14 for dimensions not shown in these drawings.
5. Refer to the page D-29 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Double Reduction Upright Mounting

9060 9085

V5

V4

V3

V2
Z1

TU1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Arrangement Conguration

RL

RR

RB

LR

Nomenclature
Shaft
Arrangement

Size

P W D

Low Speed
Shaft
Type Fan

P 2 W 9060
9065
9070
9075
9075
9080
9085

LL

LB

BL

BR

BB

Nominal
Reduction Ratio

(blank) : Without Fan

F : With Fan

RL
RR
RB
LR
LL
LB
BL
BR
BB

Size
9060

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

6.3 7.1

10 11.2 12.5 14

16

18

9065
9070
9075
9080
9085

20 22.4

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 183

9060
9065
9070
9075
9080
9085

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Solid Shaft

Size

Refer to the page D-18 for details.

Double Wall Mount

Reduction

Refer to the page D-18 for details.

W1

Parallel

Y1

X1

T4

9060
9085

V1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

DIMENSIONS Parallel Shaft Triple Reduction Upright Mounting

9015 9055

QR
FC

W2

High Speed
Shaft

With Fan
Refer to the page D-23 for details.

H2
E

K3

Dimension Selection
Tables
Tables

4- J1

Y1

Speed
Reducer

K2

K1

K2

K1
Y2
E1
F

Size

9015
9025
9030
9035
9040
9045
9050
9055

339
409
454
485
541
577
610
649

160
175
200
219
235
256
255
286

257 90 135
306 95 155
343 110 160
374 129 185
398 120 200
437 141 220
467 138.5 210
506 171 245

E1
270
310
320
370
400
440
420
490

298 70
338 80
348 90
398 90
430 115
470 115
450 116.5
520 115

9015
9025
9030
9035
9040
9045
9050
9055

QR

W2/Depth

130
144
161
161
176
176
194
194

190
204
241
241
256
256
304
304

60
60
80
80
80
80
110
110

25k6
28k6
30k6
30k6
35k6
35k6
40k6
40k6

M10/22
M10/22
M10/22
M10/22
M12/28
M12/28
M16/36
M16/36

DP

H1

H2

J1

J2

K1

K2

K3

Y1

Y2

Y3

Y4

50
55
60
60
75
75
75
75

22
25
28
28
30
30
32
32

15
19
24
24
28
28
28
28

15
19
24
24
28
28
28
28

70
75
85
100
100
120
110
135

35
40
50
50
60
60
60
60

95
110
120
120
150
150
150
150

485
570
640
690
759
819
848
918

205
235
265
265
315
315
345
345

170
195
215
215
255
255
285
285

180
210
200
250
260
300
280
350

170
195
215
215
255
255
285
285

345
410
460
510
529
589
615
688

High Speed Shaft

Size

H1

K3

Y4
L

H
L

QR
Q

R
L2

4- J2

Y3

FB

FA

Y2

X2

Z2

FD

Fan
Key
X2
8
8
8
8
10
10
12
12

Y2
4
4
4
4
5
5
5
5

Z2
7
7
7
7
8
8
8
8

L2
50
50
70
70
70
70
95
95

FA

FB

FC

FD

111
129
140
150
170
170
172
172

125
125
125
140
140
140
140
140

30
30
50
50
50
50
80
80

10
10
30
22
22
22
52
52

DP

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"

105
150
205
225
305
375
445
505

11
15
20
25
35
43
45
59

Unit: mm
1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Always remove fan hood when tightening mounting bolt.

C - 184

4Refer to the page D-13 for dimensions not shown in these drawings.
5Refer to the page D-26 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Triple Reduction Upright Mounting

9015 9055

V5

V4

V3

V2
Z1

T1

U1

V1

245
285
330
330
349
391
411
411

135
145
160
160
179
181
201
201

110 58m6
140 70m6
170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

W1/Depth
M20/42
M20/42
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
18
20
22
25
25
28
28
32

L1
95
125
150
150
150
190
190
185

9015
9025
9030
9035
9040
9045
9050
9055

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
7
11
7.5
12
9
14
9
14
9
14
10
16
10
16
11
18

Solid Shaft

Size

Refer to the page D-18 for details.

Triple
Reduction

Refer to the page D-18 for details.

W1

Parallel

Y1

X1

T4

9015
9055

V1

U4

T2

TU4

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

328
358
393
403
448
463
503
528

193
213
233
243
268
283
303
323

135
145
160
160
180
180
200
205

63
73
83
88
98
108
108
123

60
70
80
85
95
105
105
120

270
300
330
330
360
370
410
410

135
150
165
165
180
185
205
205

135
150
165
165
180
185
205
205

55
65
75
85
90
105
105
115

55
65
75
85
90
105
105
115

Unit: mm

Standard Arrangement Conguration

RL

RR

RB

LR

Nomenclature
Shaft
Arrangement

Size

P W A

Low Speed
Shaft
Type Fan

P 3 9015
9025
9030
9035
9040
9045
9050
9055

LL

LB

BL

BR

BB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) : Without Fan

F : With Fan
(blank) :Solid Shaft
T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

9015

9025

9030

9035
9040

56

63

71

9045
9050

50

9055

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 185

DIMENSIONS Parallel Shaft Triple Reduction Upright Mounting

9060 9085

QR
FC

FB

FA

X2

O
P

Z2

Y2

FD

W2

High Speed Shaft

With Fan
E

Refer to the page D-23 for details.

QR
Q

4- J
K
G

R
L2

Dimension Selection
Tables
Tables

Speed
Reducer

E1
F

DP

Size

E1

9060
9065
9070
9075
9080
9085

702
748
810
863
933
989

299
338
336
383
378
422

540
586
630
683
725
781

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

577
647
647
717
717
797

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

970
1055
1115
1215
1275
1375

310
310
350
350
380
380

380
380
430
430
460
460

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

219
219
244
244
265
265

329
329
354
354
405
405

110
110
110
110
140
140

50k6
50k6
55m6
55m6
65m6
65m6

M16/36
M16/36
M20/42
M20/42
M20/42
M20/42

216 700
216 785
233 795
233 895
285 955
285 1055

Fan
Key
X2
14
14
16
16
18
18

Y2
5.5
5.5
6
6
7
7

Z2
9
9
10
10
11
11

L2
95
95
95
95
125
125

FA

FB

FC

FD

199
199
221
221
247
247

160
160
160
160
200
200

80
80
80
80
105
105

52
52
52
52
65
65

DP

Wt.
kg

Oil
Qty.
L

1"
1"
1"
1"
1"
1"

660
815
940
1160
1350
1610

68
85
106
120
130
176

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Always remove fan hood when tightening mounting bolt.

C - 186

4Refer to the page D-15 for dimensions not shown in these drawings.
5Refer to the page D-29 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Triple Reduction Upright Mounting

9060 9085

V5

V4

V3

V2
Z1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125 123
145 143
145 143
150 148
165 163
175 173
Unit: mm

Standard Arrangement Conguration

RL

RR

RB

Nomenclature
P 3 W 9060
9065
9070
9075
9080
9085

LL

Low Speed
Shaft
Shaft
Arrangement Type Fan

Size

P W D

LR

LB

BL

BR

BB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) : Without Fan

F : With Fan

Size
9060

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Nominal Reduction Ratio

20 22.4 25

28 31.5 35.5 40

45

50

56

63

71

9065
9070
9075
9080
9085

80

90

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 187

9060
9065
9070
9075
9080
9085

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Solid Shaft

Size

Refer to the page D-18 for details.

Triple
Wall Mount
Reduction

Refer to the page D-18 for details.

W1

Parallel

Y1

X1

T4

9060
9085

V1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

DIMENSIONS Parallel Shaft Quadruple Reduction Upright Mounting

9030 9055

Z2

X2

Y3

Y2

W2

High Speed Shaft

QR
Q

4- J1

Speed
Reducer

Dimension Selection
Tables
Tables

H1

K3

Y4
L

H
L

4- J2
K3

R
L2

H2
E

Y1

K1

K2

K1

K2

Y2
E1
F

Size

9030
9035
9040
9045
9050
9055

454
485
541
577
610
649

200
219
235
256
255
286

343 110 160

374 129 185
398 120 200
437 141 220
467 138.5 210
506 171 245

E1
320
370
400
440
420
490

H1

H2

J1

J2

K1

K2

K3

Y1

Y2

Y3

Y4

348 90
60
398 90
60
430 115 75
470 115 75
450 116.5 75
520 115 75

28
28
30
30
32
32

24
24
28
28
28
28

24
24
28
28
28
28

85
100
100
120
110
135

50
50
60
60
60
60

120
120
150
150
150
150

640
690
759
819
848
918

265
265
315
315
345
345

223
248
279
299
289
324

215
215
255
255
285
285

200
250
260
300
280
350

215
215
255
255
285
285

460
510
529
589
615
688

High Speed Shaft

Size
9030
9035
9040
9045
9050
9055

DP

QR

W2/Depth

159
159
175
175
195
195

219
219
135
235
275
275

60
60
60
60
80
80

25k6
25k6
28k6
28k6
30k6
30k6

M10/22
M10/22
M10/22
M10/22
M10/22
M10/22

Key
X2
8
8
8
8
8
8

Y2
4
4
4
4
4
4

Z2
7
7
7
7
7
7

L2
50
50
50
50
70
70

DP

Wt.
kg

Oil
Qty.
L

3/4"
3/4"
1"
1"
1"
1"

210
230
310
380
450
510

20
25
35
43
46
59

Unit: mm

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3. Refer to the page D-13 for dimensions not shown in these drawings.

C - 188

4. Refer to the page D-26 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Quadruple Reduction Upright Mounting

9030 9055

U1

330
330
349
391
411
411

160
160
179
181
201
201

170 80m6
170 90m6
170 95m6
210 105m6
210 110m6
210 120m6

9030
9035
9040
9045
9050
9055

V5

V4

V3

V2
Z1

T1

V1

W1/Depth
M20/42
M20/42
M24/50
M24/50
M24/50
M24/50

X1
22
25
25
28
28
32

L1
150
150
150
190
190
185

TU1

Hollow Shaft (Shrink Disk Type)

Key
Y1
Z1
9
14
9
14
9
14
10
16
10
16
11
18

Solid Shaft

Size

Refer to the page D-18 for details.

Quadruple
Reduction

Refer to the page D-18 for details.

W1

Parallel

Y1

X1

T4

9030
9055

V1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Monoblock

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

393
403
448
463
503
528

233
243
268
283
303
323

160
160
180
180
200
205

83
88
98
108
108
123

80
85
95
105
105
120

330
330
360
370
410
410

165
165
180
185
205
205

165
165
180
185
205
205

75
85
90
105
105
115

75
85
90
105
105
115

Unit: mm

Standard Arrangement Conguration

RL

RR

RB

Nomenclature

Low Speed
Shaft
Shaft
Arrangement Type

Size

P W A

P 4 9030
9035
9040
9045
9050
9055

LR

LL

LB

BL

BR

BB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB
BL
BR
BB

Size
(blank) :Solid Shaft
T : Hollow Shaft
9030
(Shrink Disk type)
K : Hollow Shaft (Key type) 9035

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500

9040

9045

9050

9055

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 189

DIMENSIONS Parallel Shaft Quadruple Reduction Upright Mounting

9060 9085

O
P

Y2

X2

Z2

X1

W2

High Speed Shaft

H
E
QR
Q

Y
L

4- J
K
G

R
L2

Dimension Selection
Tables
Tables

Speed
Reducer

E1
F

DP

Size

E1

X1

9060
9065
9070
9075
9080
9085

702
748
810
863
933
989

299
338
336
383
378
422

540
586
630
683
725
781

151
190
163
210
205
249

265
300
300
335
335
375

530
600
600
670
670
750

577
647
647
717
717
797

135
135
160
160
160
160

35
35
40
52
52
52

35
35
42
42
42
42

180
180
215
220
220
220

970
1055
1115
1215
1275
1375

310
310
350
350
380
380

380
380
430
430
460
460

73
73
67
67
93
93

357 700
392 785
409 795
444 895
461 955
501 1055

High Speed Shaft

Size
9060
9065
9070
9075
9080
9085

QR

W2/Depth

221
221
244
244
264
264

301
301
354
354
374
374

80
80
110
110
110
110

35k6
35k6
40k6
40k6
45k6
45k6

M12/28
M12/28
M16/36
M16/36
M16/36
M16/36

Key
X2
10
10
12
12
14
14

Y2
5
5
5
5
5.5
5.5

DP
Z2
8
8
8
8
9
9

1. Key and keyways are based on ISO R773-1969 Close keys (JIS B1301-1996 Parallel key in fastening type)
2. The oil quantity is approximate. Oil shall be supplied within the range shown on the oil gauge.
3Refer to the page D-15 for dimensions not shown in these drawings.

C - 190

L2
70
70
95
95
95
95

1"
1"
1"
1"
1"
1"

Wt.
kg

Oil
Qty.
L

660 69
815 86
950 108
1170 122
1360 130
1620 175
Unit: mm

4Refer to the page D-29 for the dimension of optional parts.

DIMENSIONS Parallel Shaft Quadruple Reduction Upright Mounting

9060 9085

V5

V4

V3

V2
Z1

TU1

T1

U1

V1

W1/Depth

440
484
509
562
582
585

230
234
259
262
282
285

210
250
250
300
300
300

125m6
140m6
145m6
160m6
165m6
175m6

M24/50
M30/60
M30/60
M30/60
M30/60
M30/60

X1
32
36
36
40
40
45

L1
185
225
225
275
275
270

Hollow Shaft (Key Type)

TU2

T2

U2

V2

V3

TU4

T4

U4

V4

V5

583
594
644
651
714
714

353
359
384
386
429
429

230
235
260
265
285
285

128
143
148
158
173
183

125
140
145
155
170
180

470
480
530
530
570
570

235
240
265
265
285
285

235
240
265
265
285
285

125
145
145
150
165
175

123
143
143
148
163
173

Unit: mm

Standard Arrangement Conguration

RL

RR

Nomenclature
Size

P W D

RB

Low Speed
Shaft
Shaft
Arrangement Type

P 4 W 9060
9065
9070
9075
9080
9085

LR

LL

LB

BL

BR

BB

Nominal
Reduction Ratio

RL
RR
RB
LR
LL
LB
BL
BR
BB

(blank) :Solid Shaft

T : Hollow Shaft
(Shrink Disk type)
K : Hollow Shaft (Key type)

Size

Nominal Reduction Ratio

80

90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500

9060

9065

9070

9075
9080
9085

H
L

Air Breather

Air Vent

Oil Fill

Drain Plug

Dip Stick

Oil Gauge

Inspection
Cover

Oil Pump

Backstop Opposite
(Option)
Side

C - 191

9060
9065
9070
9075
9080
9085

Hollow Shaft (Shrink Disk Type)

Key
Y1 Z1
11
18
12
20
12
20
13
22
13
22
15
25

Solid Shaft

Size

Refer to the page D-18 for details.

Quadruple Wall Mount

Reduction

Refer to the page D-18 for details.

W1

Parallel

Y1

X1

T4

9060
9085

V1

TU4
U4

T2

U2

TU2
T1

TU1
U1
L1

Hollow Shaft (Key Type)

Split

Hollow Shaft (Shrink Disk Type)

Upright

Solid Shaft

PARAMAX

Slow Speed Shaft

C - 192

D
TECHNICAL DATA
Lubricant and Installation
Painting Specications
and Rust Proof Standard
Moment of Inertia
of Right Angle Shaft
2
GD of Right Angle Shaft
Moment of Inertia
of Parallel Shaft
2
GD of Parallel Shaft
Supplementary Dimension
Drawing
Supplementary Matters
to Hollow Shaft
Hollow Shaft Related
Dimensions
Cooling Fan Dimension
Option Dimension
Motor Terminal Box
Motor Flange Dimension
Formula of Drive System

D- 2
D- 3
D- 4
D- 6
D- 8
D-10
D-12
D-17
D-18
D-20
D-24
D-32
D-34
D-36

D-1

TECHNICAL DATA Lubricant, Installation

Lubricant
Operation Condition
/ Application

Continuous Operation

Ambient Temperature

Output Speed

-10 to 15

0 to 30

10 to 50

Over
100r/min

ISO*
AGMA

VG68
2EP

VG150
4EP

VG220
5EP

Under
100r/min

ISO*
AGMA

VG100
3EP

VG220
5EP

VG320
6EP

All

ISO*
AGMA

VG68
2EP

VG150
4EP

VG220
5EP

Intermittent Operation
(ex. Crane Drive)

* Kinetic Viscosity (mm/s) at ISO 40

PARAMAX DRIVE is shipped without lubrication oil.

Supply oil within the range shown on the dip stick before operation.
The table on the right shows appropriate viscosity of oil based on ISO and AGMA for respective
ambient temperatures and slow speed shaft r/min.
When the ambient temperature is lower than -10 deg or higher than +50 deg, a heating or cooling
unit is necessary, in general.

Gear Oil

Recommended Lubricants
Brand

BP

ISO VG68
AGMA 2EP

ENERGOL
GR-XP-68

ALPHA
SP68

OPTIGEAR
BM68

TRIBOL
1100/68

ISO VG100
AGMA 3EP

ENERGOL
GR-XP-100

ALPHA
SP100

OPTIGEAR
BM100

TRIBOL
1100/100

ISO VG150
AGMA 4EP

ENERGOL
GR-XP-150

ALPHA
SP150

OPTIGEAR
BM150

TRIBOL
1100/150

ISO VG220
AGMA 5EP

ENERGOL
GR-XP-220

ALPHA
SP220

OPTIGEAR
BM220

TRIBOL
1100/220

ISO VG320
AGMA 6EP

ENERGOL
GR-XP-320

ALPHA
SP320

OPTIGEAR
BM320

TRIBOL
1100/320

SPHEEROL Olista LongAP3

time 3EP

TRIBOL
3020/
1000-2

Bearing grease

Common

Technical

ENERGREASE
LS EP2

CASTROL

CHEVRON TEXACO
GEAR
COMPOUNDS
EP68
GEAR
COMPOUNDS
EP100
GEAR
COMPOUNDS
EP150
GEAR
COMPOUNDS
EP220
GEAR
COMPOUNDS
EP320
DURALITH
GREASE 68

EXXON MOBIL

MEROPA
WM68

SPARTAN
EP68

MEROPA
WM100

SPARTAN
EP100

MEROPA
WM150

SPARTAN
EP150

MEROPA
WM220

SPARTAN
EP220

MEROPA
WM320

SPARTAN
EP320

MULTIFAK EP2

BEACON
EP2

MOBILGEAR
626
MOBILGEAR
627
MOBILGEAR
629
MOBILGEAR
630
MOBILGEAR
632
MOBILPLEX
48

Installation
(1) Consult us when PARAMAX DRIVE is to be installed on an inclined surface or on a ceiling.
Additional lubrication system may be necessary.
(2) Install PARAMAX DRIVE horizontally on a sufficiently rigid base.
When the unit is made for inclined installation according to your specification,
do not install it at any other angle other than the specified angle.
(3) Installation bolts for PARAMAX DRIVE shall be equivalent to JIS strength classification 10.9.
Consult us when the force that pushes up PARAMAX DRIVE is to be applied.
(4) Refer to the maintenance manual attached to the unit for other installation notes.

D-

SHELL

TOTAL

OMALA
68

CARTER
EP68

OMALA
100

CARTER
EP100

OMALA
150

CARTER
EP150

OMALA
220

CARTER
EP220

OMALA
320

CARTER
EP320

ALVANIA
EP2

MULTIS
EP2

TECHNICAL DATA Painting Specications, Rust Proof Standard

Painting Specications
Painting
Surface
Area Conditioning

Kind of Painting

Outside
Painting

Standard
painting

Acrylic modied
phthalic

Under

20 40

Modied alkyd resin

Standard under coat

Finish

15 30

Acrylic modied alkyd resin

Standard nish coat

Acrylic modied
phthalic

Under

40 80

Modied alkyd resin

Finish

15 30

Acrylic modied alkyd resin

Acrylic modied
phthalic

Under

40 80

Modied alkyd resin

Acrylic modied alkyd resin

Special
painting
(Including Long of oil phthalic
rust-proof
and heat
resisting
Chloride rubber
painting)
One layer
of
Unigrand
PTC Primer
Phenol
as the rst
primer
Heat-proof silver

Extra
rust-proof
painting
Steel Plate
Class 2

Inside
Painting

Cast Iron
Class 1
Steel
Plate Class 3

Application

Class

Standard
export
painting

Cast Iron
Class 1

Painting Specication of

Painting of Finish
Coat

Extra
rust-proof
painting
(Sand
blast under
coating)

Type Coating Thickness

Finish

30 60

40 80

Modied alkyd resin

Finish

30 60

Synthetics resin paint

Under

40 80

Modied alkyd resin

Second

20 40

Phenol M.I.O paint

Finish

30 60

Chloride rubber paint

Under

40 80

Modied alkyd resin

Finish

30 60

Phenol resin enamel

Under

20 40

Modied alkyd resin

Finish

15 30

Aluminum paint

Under

40 80

Special permeability epoxy aluminium paint

Finish

120 240

Polyamide epoxy

Under

40 80

Special permeability epoxy aluminium paint

Finish

45 90

Polyisocianate urethane resin paint

Polyurethane

Standard
painting

Export standard

Under

Epoxy

Thick lm epoxy

Type of Coating

250 350 Thick lm type modied epoxy resin paint

20 40

Modied alkyd resin

Moderate corrosive atmosphere,

seaside, outdoor humid atmosphere,
chemical plant area, ... etc.
Ocean-going vessel & boat,
bridge, seaside, outdoor humid
atmosphere, ... etc.
Ocean-going vessel & boat,
bridge, seaside, outdoor humid
atmosphere, ... etc.
In-and-outdoor of acid treating
plant and chemical plant etc...
Heating furnace (120 deg),
... etc.
Indoor anti-corrosion area,
Chemical plant
Outdoor anti-corrosion area,
Chemical plant

Submersible equipment,
marine structure, ... etc.

Standard inside painting

Note : SUMITOMO standard color is Donau Blue (equivalent Munsell color: 6.5PB 3.6 / 8.2)

Rust Proof Standard

Rust proong treatment has been conducted on all completely assembled models, prior to shipment.

1. Standard rust proofing specifications

(1) Outside rust proong
Rust proong oil has been applied to products before shipment.
Check the rust proong conditions every 6 months after shipment, and conduct rust proong treatment, as
necessary.

Rust proong period

6 months

Storage condition

Generally to be stored inside the shop or warehouse, relatively free of humidity, dust,
extreme temperature uctuation, corrosive gas, and similar atmosphere.
After shipment, the product shall be operated 5-10 minutes every 2-3 months with
recommended lubricants.

2. Export rust proong specications

Consult us for export rust proong when export specications or severe specications are required.

D-3

TECHNICAL DATA Moment of Inertia

Right Angle Shaft

Right Angle Shaft Double Reduction

Moment of Inertia at high speed shaft
Nominal
reduction ratio 9015
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4

0.00423
0.00400
0.00288
0.00275
0.00218
0.00210
0.00188
0.00183
0.00133
0.00130

9025
0.00805
0.00750
0.00508
0.00475
0.00488
0.00468
0.00390
0.00375
0.00258
0.00250

9030

9035

0.0157
0.0153
0.0137 0.0181
0.0134 0.0175
0.0111 0.0152
0.0109 0.0149
0.00843 0.0120
0.00830 0.0118
0.00583 0.00908
0.00575 0.00890
0.00620
0.00610

9040
0.0333
0.0313
0.0283
0.0269
0.0201
0.0193
0.0138
0.0133
0.0107
0.0104

9045

0.0374
0.0346
0.0311
0.0292
0.0217
0.0206
0.0149
0.0142
0.0114
0.0109

Size of Reducer
9050 9055 9060
0.0662
0.0621
0.0603
0.0577
0.0492
0.0475
0.0357
0.0345
0.0243
0.0237

0.0745
0.0681
0.0653
0.0614
0.0525
0.0499
0.0379
0.0362
0.0257
0.0246

0.146
0.135
0.130
0.124
0.0981
0.0939
0.0691
0.0664
0.0514
0.0497

9065

0.166
0.149
0.1426
0.1319
0.1056
0.0990
0.0739
0.0697
0.0546
0.0518

9070
0.301
0.281
0.253
0.242
0.203
0.196
0.139
0.135
0.102
0.0987

9075

0.337
0.311
0.274
0.259
0.216
0.207
0.147
0.141
0.107
0.103

9080
0.502
0.475
0.480
0.464
0.398
0.387
0.268
0.261
0.194
0.190

9085

0.562
0.524
0.516
0.493
0.422
0.407
0.282
0.273
0.203
0.198

Right Angle Shaft Triple Reduction

Moment of Inertia at high speed shaft
Nominal
reduction ratio 9015

9025

20
22.4
25
28
31.5
35.5
40
45
50
56
63
71
80
90
100

9030
0.00378
0.00373
0.00338
0.00333
0.00193
0.00190
0.00178
0.00175
0.00118
0.00115
0.00110
0.00110

9035

0.00403
0.00395
0.00353
0.00350
0.00203
0.00200
0.00183
0.00183
0.00120
0.00120
0.00113
0.00113

9040
0.00693
0.00670
0.00608
0.00595
0.00433
0.00425
0.00403
0.00398
0.00233
0.00230
0.00220
0.00218

9045

0.00735
0.00705
0.00635
0.00618
0.00450
0.00440
0.00413
0.00405
0.00240
0.00235
0.00225
0.00223

Size of Reducer
9050 9055 9060
0.0140
0.0136
0.0115
0.0112
0.00835
0.00818
0.00738
0.00730
0.00555
0.00550
0.00423
0.00418

0.0149
0.0142
0.0120
0.0116
0.00868
0.00843
0.00758
0.00743
0.00568
0.00558
0.00430
0.00423

9065

0.0289
0.0278
0.0237 0.0310
0.0230 0.0292
0.0183 0.0248
0.0178 0.0238
0.0161 0.0191
0.0159 0.0184
0.0120 0.0166
0.0118 0.0162
0.00893 0.01230
0.00883 0.01203
0.00910
0.00895

9070
0.0590
0.0571
0.0515
0.0503
0.0359
0.0351
0.0328
0.0323
0.0239
0.0236
0.0173
0.0171

9075

0.0624
0.0600
0.0537
0.0521
0.0373
0.0363
0.0337
0.0331
0.0245
0.0241
0.0176
0.0174

9080
0.121
0.118
0.106
0.104
0.0700
0.0689
0.0644
0.0636
0.0484
0.0479
0.0349
0.0346

9085

0.126
0.123
0.110
0.108
0.0722
0.0708
0.0659
0.0649
0.0493
0.0487
0.0355
0.0351

Right Angle Shaft Quadruple Reduction

Moment of Inertia at high speed shaft
Nominal
reduction ratio 9015

Common

Technical

D-4

63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

9025

9030

9035

9040

0.00295
0.00293
0.00215
0.00215
0.00203
0.00203

9045

0.00298
0.00295
0.00218
0.00215
0.00205
0.00203

Size of Reducer
9050 9055 9060

0.00283
0.00280
0.00268
0.00265
0.00243
0.00243
0.00120
0.00120
0.00118
0.00118
0.00110
0.00110
0.00110
0.00108

0.00288
0.00283
0.00270
0.00268
0.00245
0.00243
0.00123
0.00120
0.00118
0.00118
0.00113
0.00110
0.00110
0.00108

0.00553
0.00548
0.00523
0.00518
0.00473
0.00470
0.00243
0.00240
0.00235
0.00233
0.00223
0.00220
0.00220
0.00215

9065

0.00565
0.00555
0.00530
0.00523
0.00475
0.00473
0.00245
0.00243
0.00235
0.00235
0.00223
0.00223
0.00220
0.00218

9070

0.0113
0.0112
0.0108
0.0107
0.00923
0.00918
0.00480
0.00478
0.00468
0.00465
0.00428
0.00425
0.00420
0.00418

9075

0.0115
0.0114
0.0110
0.0109
0.00930
0.00925
0.00483
0.00473
0.00470
0.00430
0.00428
0.00423
0.00418

9080

0.0229
0.0227
0.0219
0.0218
0.0188
0.0188
0.00993
0.00990
0.00970
0.00968
0.00893
0.00893
0.00885
0.00868

9085

0.0233
0.0230
0.0222
0.0220
0.0190
0.0189
0.0100
0.0100
0.00978
0.00973
0.00898
0.00895
0.00885
0.00868

TECHNICAL DATA Moment of Inertia

Right Angle Shaft

Unit: kg-m2
9090

9095

9100

1.18
1.16
0.871
0.858
0.638
0.630
0.464
0.459

9105

9110

2.23
2.20
1.68
1.65
1.22
1.20
0.894
0.884

Size of Reducer
9115 9118 9121

9126

9128

9131

Nominal
9136 reduction ratio
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4

4.16
3.98
3.10
2.99
2.28
2.21
1.68
1.63

Unit: kg-m2
9090
0.240
0.237
0.212
0.210
0.141
0.140
0.129
0.129
0.0931
0.0927
0.0664
0.0661
0.0642

9095
0.249
0.245
0.218
0.215
0.144
0.143
0.132
0.131
0.0945
0.0940
0.0673
0.0669
0.0648

9100
0.460
0.453
0.401
0.397
0.264
0.262
0.241
0.239
0.175
0.174
0.127
0.126
0.121

9105
0.476
0.470
0.412
0.408
0.271
0.268
0.245
0.244
0.178
0.177
0.129
0.128
0.123

9110
0.889
0.866
0.774
0.759
0.454
0.445
0.409
0.403
0.311
0.307
0.225
0.223
0.211

Size of Reducer
9115 9118 9121
0.926
0.896
0.798
0.779
0.468
0.456
0.418
0.411
0.317
0.312
0.229
0.226
0.214

9126

9128

9131

Nominal
9136 reduction ratio

0.959
0.701
0.731
0.615
0.559
0.443
0.408
0.322
0.300
0.232
0.218

2.18
2.12
1.29
1.25
0.939
0.917
0.683
0.668
0.509
0.500

2.21
2.15
1.31
1.27
0.952
0.928
0.691
0.675
0.515
0.505

2.39
2.33
1.78
1.74
1.28
1.26
0.934
0.919

4.48
4.24
3.31
3.16
2.41
2.32
1.76
1.70

4.53
4.28
3.34
3.18
2.43
2.33
1.77
1.71

20
22.4
25
28
31.5
35.5
40
45
50
56
63
71
80
90
100

Unit: kg-m2
9090

0.0467
0.0452
0.0451
0.0409
0.0408
0.0243
0.0242
0.0183
0.0183
0.0172
0.0172
0.0171
0.0163

9095

0.0472
0.0455
0.0454
0.0411
0.0410
0.0244
0.0244
0.0184
0.0183
0.0172
0.0172
0.0171
0.0164

9100

0.0962
0.0930
0.0927
0.0846
0.0844
0.0493
0.0492
0.0370
0.0369
0.0349
0.0348
0.0345
0.0334

9105

0.0972
0.0937
0.0934
0.0850
0.0849
0.0496
0.0495
0.0371
0.0371
0.0350
0.0350
0.0346
0.0334

9110

0.108
0.102
0.101
0.0908
0.0902
0.0527
0.0523
0.0393
0.0391
0.0364
0.0363
0.0355
0.0341

Size of Reducer
9115
9118
9121

0.110
0.104
0.102
0.0918
0.0910
0.0533
0.0528
0.0397
0.0394
0.0367
0.0365
0.0357
0.0343

0.139
0.123
0.105
0.100
0.0927
0.0890
0.0693
0.0544
0.0516
0.0501
0.0477
0.0360
0.0345

0.235
0.230
0.199
0.196
0.152
0.150
0.137
0.136
0.0978
0.0969
0.0693
0.0688
0.0664

9126

0.238
0.233
0.201
0.198
0.154
0.151
0.138
0.136
0.0983
0.0974
0.0696
0.0690
0.0667

9128

0.502
0.492
0.429
0.423
0.281
0.277
0.252
0.250
0.143
0.141
0.131
0.130
0.125

9131
0.979
0.819
0.713
0.688
0.505
0.489
0.448
0.438
0.326
0.319
0.234
0.230
0.217

9136
0.987
0.825
0.718
0.692
0.508
0.492
0.450
0.439
0.327
0.320
0.235
0.231
0.217

Nominal
reduction ratio
63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

D-5

TECHNICAL DATA GD2

Right Angle Shaft

Right Angle Shaft Double Reduction

GD2 at high speed shaft
Nominal
reduction ratio 9015
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4

0.0169
0.0160
0.0115
0.0110
0.0087
0.0084
0.0075
0.0073
0.0053
0.0052

9025

9030

0.0322
0.0300
0.0203
0.0190
0.0195
0.0187
0.0156
0.0150
0.0103
0.0100

0.0629
0.0610
0.0548
0.0536
0.0443
0.0436
0.0337
0.0332
0.0233
0.0230

9035

0.0723
0.0699
0.0609
0.0594
0.0481
0.0472
0.0363
0.0356
0.0248
0.0244

9040
0.133
0.125
0.113
0.108
0.0805
0.0772
0.0553
0.0532
0.0428
0.0414

9045

0.150
0.138
0.1242
0.1167
0.0869
0.0825
0.0594
0.0566
0.0455
0.0437

Size of Reducer
9050 9055 9060
0.265
0.248
0.241
0.231
0.197
0.190
0.143
0.138
0.0972
0.0946

0.298
0.272
0.261
0.246
0.210
0.200
0.152
0.145
0.103
0.0985

0.584
0.541
0.522
0.495
0.392
0.376
0.276
0.266
0.206
0.199

9065

0.663
0.594
0.570
0.528
0.423
0.396
0.296
0.279
0.218
0.207

9070
1.20
1.13
1.01
0.968
0.812
0.783
0.556
0.538
0.407
0.395

9075

1.35
1.24
1.10
1.04
0.865
0.827
0.590
0.566
0.429
0.413

9080
2.01
1.90
1.92
1.86
1.59
1.55
1.07
1.04
0.777
0.759

9085

2.25
2.10
2.06
1.97
1.69
1.63
1.13
1.09
0.814
0.790

Right Angle Shaft Triple Reduction

GD2 at high speed shaft
Nominal
reduction ratio 9015

9025

20
22.4
25
28
31.5
35.5
40
45
50
56
63
71
80
90
100

9030
0.0151
0.0149
0.0135
0.0133
0.0077
0.0076
0.0071
0.0070
0.0047
0.0046
0.0044
0.0044

9035

0.0161
0.0158
0.0141
0.0140
0.0081
0.0080
0.0073
0.0073
0.0048
0.0048
0.0045
0.0045

9040
0.0277
0.0268
0.0243
0.0238
0.0173
0.0170
0.0161
0.0159
0.0093
0.0092
0.0088
0.0087

9045

0.0294
0.0282
0.0254
0.0247
0.0180
0.0176
0.0165
0.0162
0.0096
0.0094
0.0090
0.0089

Size of Reducer
9050 9055 9060
0.0559
0.0542
0.0459
0.0449
0.0334
0.0327
0.0295
0.0292
0.0222
0.0220
0.0169
0.0167

0.0594
0.0567
0.0479
0.0464
0.0347
0.0337
0.0303
0.0297
0.0227
0.0223
0.0172
0.0169

9065

0.116
0.111
0.0946 0. 1238
0.0919 0.1167
0.0730 0.0993
0.0712 0.0952
0.0645 0.0764
0.0635 0.0735
0.0480 0.0665
0.0473 0.0648
0.0357 0.0492
0.0353 0.0481
0.0364
0.0358

9070
0.236
0.229
0.206
0.201
0.144
0.141
0.131
0.129
0.0957
0.0945
0.0690
0.0682

9075

0.250
0.240
0.215
0.208
0.149
0.145
0.135
0.132
0.0979
0.0963
0.0704
0.0694

9080
0.482
0.471
0.425
0.418
0.280
0.276
0.257
0.255
0.193
0.192
0.140
0.139

9085

0.505
0.491
0.440
0.431
0.289
0.283
0.264
0.260
0.197
0.195
0.142
0.141

Right Angle Shaft Quadruple Reduction

GD2 at high speed shaft
Nominal
reduction ratio 9015

Common

Technical

D-6

63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

9025

9030

9035

9040

0.0118
0.0117
0.0086
0.0086
0.0081
0.0081

9045

0.0119
0.0118
0.0087
0.0086
0.0082
0.0081

Size of Reducer
9050 9055 9060

0.0113
0.0112
0.0107
0.0106
0.0097
0.0097
0.0048
0.0048
0.0047
0.0047
0.0044
0.0044
0.0044
0.0043

0.0115
0.0113
0.0108
0.0107
0.0098
0.0097
0.0049
0.0048
0.0047
0.0047
0.0045
0.0044
0.0044
0.0043

0.0221
0.0219
0.0209
0.0207
0.0189
0.0188
0.0097
0.0096
0.0094
0.0093
0.0089
0.0088
0.0088
0.0086

9065

0.0226
0.0222
0.0212
0.0209
0.0190
0.0189
0.0098
0.0097
0.0094
0.0094
0.0089
0.0089
0.0088
0.0087

9070

0.0452
0.0447
0.0432
0.0429
0.0369
0.0367
0.0192
0.0191
0.0187
0.0186
0.0171
0.0170
0.0168
0.0167

9075

0.0461
0.0455
0.0438
0.0434
0.0372
0.0370
0.0195
0.0193
0.0189
0.0188
0.0172
0.0171
0.0169
0.0167

9080

0.0914
0.0907
0.0877
0.0872
0.0753
0.0751
0.0397
0.0396
0.0388
0.0387
0.0357
0.0357
0.0354
0.0347

9085

0.0930
0.0920
0.0887
0.0881
0.0759
0.0756
0.0401
0.0399
0.0391
0.0389
0.0359
0.0358
0.0354
0.0347

GD2(kgfm2)

TECHNICAL DATA GD2

Right Angle Shaft

Unit: kgf-m2
9090

9095

9100

4.72
4.63
3.48
3.43
2.55
2.52
1.86
1.84

9105

9110

8.94
8.78
6.70
6.61
4.88
4.82
3.57
3.54

Size of Reducer
9115 9118 9121

9126

9128

9131

Nominal
9136 reduction ratio
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4

16.6
15.9
12.4
12.0
9.14
8.85
6.71
6.53

Unit: kgf-m2
9090
0.960
0.949
0.848
0.842
0.563
0.559
0.518
0.515
0.372
0.371
0.266
0.265
0.257

9095
0.994
0.981
0.870
0.862
0.578
0.572
0.527
0.523
0.378
0.760
0.269
0.268
0.259

9100
1.84
1.81
1.60
1.59
1.06
1.05
0.964
0.958
0.699
0.695
0.507
0.505
0.485

9105
1.91
1.88
1.65
1.63
1.08
1.07
0.982
0.975
0.710
0.706
0.514
0.512
0.491

9110
3.56
3.47
3.10
3.04
1.81
1.78
1.64
1.61
1.24
1.23
0.900
0.890
0.845

Size of Reducer
9115 9118 9121
3.70
3.59
3.19
3.12
1.87
1.83
1.67
1.64
1.27
1.25
0.915
0.903
0.854

9126

9128

9131

Nominal
9136 reduction ratio

3.84
2.80
2.92
2.46
2.24
1.77
1.63
1.29
1.20
0.928
0.872

8.71
8.48
5.16
5.01
3.76
3.67
2.73
2.67
2.04
2.00

8.84
8.59
5.24
5.08
3.81
3.71
2.76
2.70
2.06
2.02

9.58
9.34
7.10
6.95
5.13
5.03
3.73
3.67

17.9
17.0
13.2
12.6
9.65
9.27
7.04
6.79

18.1
17.1
13.4
12.7
9.73
9.33
7.09
6.83

20
22.4
25
28
31.5
35.5
40
45
50
56
63
71
80
90
100

Unit: kgf-m2
9090

0.187
0.181
0.180
0.163
0.163
0.0970
0.0969
0.0731
0.0730
0.0687
0.0687
0.0682
0.0653

9095

0.189
0.182
0.182
0.164
0.164
0.0976
0.0974
0.0734
0.0733
0.0689
0.0689
0.0683
0.0654

9100

0.385
0.372
0.371
0.338
0.338
0.197
0.197
0.148
0.148
0.140
0.139
0.138
0.133

9105

0.389
0.375
0.374
0.340
0.339
0.198
0.198
0.149
0.148
0.140
0.140
0.138
0.134

9110

0.431
0.409
0.405
0.363
0.361
0.211
0.209
0.157
0.156
0.146
0.145
0.142
0.137

Size of Reducer
9115 9118 9121

0.439
0.415
0.410
0.367
0.364
0.213
0.211
0.159
0.157
0.147
0.146
0.143
0.137

0.554
0.490
0.420
0.398
0.371
0.356
0.277
0.217
0.206
0.200
0.191
0.144
0.138

0.941
0.920
0.797
0.784
0.609
0.600
0.548
0.542
0.391
0.388
0.277
0.275
0.266

9126

0.954
0.930
0.805
0.790
0.614
0.605
0.552
0.545
0.393
0.389
0.279
0.276
0.267

9128

2.01
1.97
1.72
1.69
1.12
1.11
1.01
0.998
0.571
0.565
0.525
0.521
0.498

9131
3.91
3.28
2.85
2.75
2.02
1.96
1.79
1.75
1.30
1.28
0.936
0.920
0.867

Nominal
9136 reduction ratio
3.95
3.30
2.87
2.77
2.03
1.97
1.80
1.76
1.31
1.28
0.940
0.923
0.868

63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

D-7

TECHNICAL DATA Moment of Inertia

Parallel shaft

Parallel Shaft Double Reduction

Moment of Inertia at high speed shaft
Nominal
reduction ratio 9015
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4

0.00238
0.00215
0.00185
0.00170
0.00133
0.00125
0.00100
0.00095
0.00078
0.00073

9025

9030

0.00508
0.00455
0.00433
0.00398
0.00305
0.00283
0.00218
0.00205
0.00173
0.00163

0.0110
0.0105
0.00913
0.00880
0.00718
0.00698
0.00463
0.00450
0.00365
0.00355

9035

0.0135
0.0129
0.0107
0.0103
0.00820
0.00795
0.00523
0.00508
0.00403
0.00393

9040

9045

0.0211
0.0188
0.0158 0.0257
0.0144 0.0226
0.0136 0.0186
0.0126 0.0167
0.00933 0.0154
0.00878 0.0142
0.00725 0.0104
0.00690 0.00965
0.00795
0.00748

Size of Reducer
9050 9055 9060
0.0416
0.0376
0.0336
0.0309
0.0267
0.0251
0.0210
0.0200
0.0149
0.0142

0.0496
0.0434
0.0389
0.0348
0.0300
0.0275
0.0232
0.0215
0.0161
0.0151

0.109
0.0977
0.0787
0.0721
0.0619
0.0576
0.0443
0.0415
0.0312
0.0296

9065

0.128
0.111
0.0909
0.0803
0.0699
0.0629
0.0493
0.0449
0.0342
0.0316

9070
0.226
0.207
0.167
0.155
0.132
0.124
0.0898
0.0851
0.0708
0.0678

9075

0.262
0.236
0.188
0.173
0.147
0.136
0.0984
0.0922
0.0764
0.0724

9080
0.447
0.420
0.326
0.309
0.256
0.245
0.165
0.158
0.129
0.124

9085

0.502
0.466
0.360
0.337
0.279
0.264
0.179
0.169
0.138
0.132

Parallel Shaft Triple Reduction

Moment of Inertia at high speed shaft
Nominal
reduction ratio 9015
20
22.4
25
28
31.5
35.5
40
45
50
56
63
71
80
90

0.00085
0.00083
0.00073
0.00073
0.00048
0.00048
0.00043
0.00043

9025

9030

0.00210
0.00205
0.00190
0.00188
0.00115
0.00115
0.00108
0.00108

0.00288
0.00280
0.00248
0.00245
0.00153
0.00153
0.00138
0.00138
0.00090
0.00088
0.00083
0.00083

9035

0.00310
0.00305
0.00263
0.00260
0.00163
0.00160
0.00145
0.00143
0.00093
0.00093
0.00085
0.00085

9040
0.00558
0.00538
0.00478
0.00463
0.00335
0.00328
0.00303
0.00298
0.00190
0.00188
0.00178
0.00175

9045

0.00600
0.00573
0.00505
0.00485
0.00353
0.00343
0.00315
0.00308
0.00198
0.00193
0.00183
0.00180

Size of Reducer
9050 9055 9060
0.0135
0.0131
0.0109
0.0107
0.00763
0.00743
0.00658
0.00648
0.00433
0.00425
0.00393
0.00390

0.0144
0.0137
0.0115
0.0111
0.00798
0.00770
0.00680
0.00663
0.00448
0.00435
0.00400
0.00395

9065

0.0303
0.0291
0.0249 0.0324
0.0242 0.0306
0.0164 0.0261
0.0159 0.0251
0.0142 0.0172
0.0140 0.0165
0.00868 0.0147
0.00850 0.0143
0.00788 0.00900
0.00778 0.00873
0.00805
0.00790

9070
0.0588
0.0570
0.0514
0.0502
0.0317
0.0309
0.0287
0.0282
0.0175
0.0172
0.0164
0.0162

9075

0.0622
0.0598
0.0536
0.0520
0.0331
0.0321
0.0296
0.0289
0.0180
0.0177
0.0167
0.0165

9080
0.121
0.118
0.106
0.104
0.0690
0.0679
0.0632
0.0624
0.0347
0.0343
0.0325
0.0323

9085

0.127
0.123
0.110
0.108
0.0714
0.0699
0.0648
0.0637
0.0356
0.0350
0.0331
0.0328

Parallel Shaft Quadruple Reduction

Moment of Inertia at high speed shaft
Nominal
reduction ratio 9015

Common

Technical

D-8

63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

9025

9030

0.00078
0.00078
0.00075
0.00075
0.00068
0.00068
0.00043
0.00043
0.00040
0.00040

9035

0.00080
0.00078
0.00075
0.00075
0.00068
0.00068
0.00043
0.00043
0.00040
0.00040

9040

0.00200
0.00200
0.00195
0.00195
0.00183
0.00183
0.00110
0.00110
0.00105
0.00105

9045

0.00203
0.00200
0.00198
0.00195
0.00185
0.00183
0.00110
0.00110
0.00105
0.00105

Size of Reducer
9050 9055 9060

0.00278
0.00275
0.00263
0.00260
0.00238
0.00238
0.00103
0.00103
0.00098
0.00098
0.00093
0.00093
0.00093
0.00088
0.00080

0.00283
0.00278
0.00265
0.00263
0.00240
0.00238
0.00105
0.00103
0.00100
0.00100
0.00093
0.00093
0.00093
0.00090
0.00080

0.00618
0.00610
0.00585
0.00580
0.00533
0.00530
0.00220
0.00218
0.00213
0.00210
0.00200
0.00198
0.00198
0.00193
0.00163

9065

0.00630
0.00620
0.00593
0.00585
0.00538
0.00533
0.00223
0.00220
0.00213
0.00213
0.00200
0.00200
0.00198
0.00193
0.00165

9070

0.0124
0.0123
0.0119
0.0118
0.0103
0.0103
0.00493
0.00490
0.00480
0.00478
0.00440
0.00438
0.00433
0.00430
0.00353

9075

0.0126
0.0125
0.0121
0.0120
0.0104
0.0104
0.00498
0.00495
0.00483
0.00480
0.00440
0.00440
0.00435
0.00430
0.00353

9080

0.0248
0.0246
0.0238
0.0237
0.0207
0.0207
0.00883
0.00878
0.00860
0.00858
0.00783
0.00780
0.00773
0.00755
0.00685

9085

0.0252
0.0249
0.0241
0.0239
0.0209
0.0208
0.00893
0.00888
0.00865
0.00863
0.00785
0.00783
0.00775
0.00758
0.00685

TECHNICAL DATA Moment of Inertia

Parallel shaft

Unit: kg-m2
9090
0.865
0.840
0.693
0.675
0.490
0.480
0.323
0.318
0.253
0.250

9095
0.950
0.918
0.748
0.725
0.523
0.510
0.345
0.338
0.268
0.263

9100
1.78
1.72
1.32
1.28
1.02
0.990
0.658
0.640
0.510
0.500

9105
1.95
1.89
1.42
1.39
1.09
1.06
0.700
0.683
0.538
0.528

9110
3.33
3.10
2.48
2.34
1.91
1.81
1.29
1.23
1.01
0.968

Size of Reducer
9115 9118 9121

9126

9128

9131

Nominal
9136 reduction ratio
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4

3.70
3.40
2.70
2.53
2.05
1.94
1.38
1.31
1.06
1.02

Unit: kg-m2
9090
0.239
0.237
0.212
0.210
0.139
0.138
0.128
0.127
0.0695
0.0693
0.0653
0.0650
0.0630

9095
0.248
0.245
0.217
0.215
0.143
0.142
0.130
0.129
0.0710
0.0705
0.0660
0.0658
0.0638

9100
0.508
0.500
0.450
0.445
0.300
0.298
0.275
0.275
0.138
0.137
0.128
0.127
0.122

9105
0.523
0.518
0.460
0.458
0.308
0.305
0.280
0.278
0.141
0.140
0.130
0.129
0.124

9110
0.720
0.698
0.610
0.595
0.398
0.388
0.350
0.345
0.178
0.174
0.159
0.157
0.145

Size of Reducer
9115 9118 9121
0.755
0.728
0.633
0.615
0.413
0.400
0.360
0.353
0.184
0.179
0.163
0.160
0.147

9126

9128

0.787
0.654
0.567
0.426
0.418
0.370
0.333
0.216
0.194
0.166
0.152

1.20
1.15
0.941
0.906
0.630
0.609
0.486
0.473
0.367
0.358
0.309

1.23
1.17
0.962
0.923
0.643
0.619
0.494
0.479
0.372
0.362
0.312

2.34
2.24
1.72
1.65
1.14
1.10
0.810
0.786
0.626
0.610
0.491

9131
4.58
4.19
3.36
3.13
2.32
2.16
1.73
1.63
1.34
1.28
1.02

Nominal
9136 reduction ratio
4.66
4.25
3.41
3.16
2.35
2.18
1.75
1.65
1.36
1.29
1.03

20
22.4
25
28
31.5
35.5
40
45
50
56
63
71
80
90

Unit: kg-m2
9090

0.0675
0.0658
0.0658
0.0613
0.0613
0.0193
0.0193
0.0189
0.0189
0.0178
0.0178
0.0177
0.0170
0.0156

9095

0.0680
0.0663
0.0660
0.0615
0.0615
0.0194
0.0194
0.0190
0.0189
0.0179
0.0179
0.0177
0.0170
0.0156

9100

0.108
0.105
0.105
0.0963
0.0963
0.0398
0.0395
0.0388
0.0388
0.0368
0.0368
0.0365
0.0353
0.0295

9105

0.109
0.106
0.105
0.0968
0.0965
0.0400
0.0398
0.0390
0.0390
0.0370
0.0368
0.0365
0.0355
0.0295

9110

0.123
0.118
0.117
0.106
0.106
0.0678
0.0673
0.0425
0.0423
0.0398
0.0395
0.0388
0.0375
0.0313

Size of Reducer
9115 9118 9121

0.125
0.119
0.118
0.107
0.107
0.0683
0.0678
0.0428
0.0425
0.0400
0.0398
0.0390
0.0375
0.0313

0.147
0.138
0.121
0.115
0.108
0.105
0.0688
0.0665
0.0431
0.0621
0.0597
0.0392
0.0378
0.0315

0.250
0.221
0.218
0.199
0.189
0.164
0.158
0.113
0.110
0.0830
0.0805
0.0801
0.0626

9126

0.253
0.223
0.219
0.200
0.190
0.165
0.159
0.114
0.110
0.0833
0.0808
0.0803
0.0628

9128

0.517
0.447
0.441
0.291
0.287
0.261
0.258
0.158
0.156
0.146
0.145
0.112
0.111

9131

0.713
0.611
0.588
0.525
0.469
0.368
0.331
0.260
0.237
0.232
0.171
0.168
0.141

Nominal
9136 reduction ratio

0.719
0.616
0.592
0.528
0.471
0.371
0.332
0.261
0.238
0.233
0.172
0.169
0.141

63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

D-9

TECHNICAL DATA GD2

Parallel shaft

Parallel Shaft Double Reduction

GD2 at high speed shaft
Nominal
reduction ratio 9015
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4

0.0095
0.0086
0.0074
0.0068
0.0053
0.0050
0.0040
0.0038
0.0031
0.0029

9025

9030

0.0203
0.0182
0.0173
0.0159
0.0122
0.0113
0.0087
0.0082
0.0069
0.0065

0.0440
0.0419
0.0365
0.0352
0.0287
0.0279
0.0185
0.0180
0.0146
0.0142

9035

0.0541
0.0515
0.0426
0.0410
0.0328
0.0318
0.0209
0.0203
0.0161
0.0157

9040
0.0845
0.0753
0.0633
0.0577
0.0542
0.0505
0.0373
0.0351
0.0290
0.0276

9045

0.1027
0.0903
0.0743
0.0668
0.0616
0.0566
0.0415
0.0386
0.0318
0.0299

Size of Reducer
9050 9055 9060
0.166
0.150
0.134
0.124
0.107
0.100
0.0841
0.0798
0.0594
0.0569

0.199
0.174
0.156
0.139
0.120
0.110
0.0926
0.0860
0.0643
0.0605

0.434
0.391
0.315
0.288
0.248
0.230
0.177
0.166
0.125
0.119

9065

0.513
0.444
0.364
0.321
0.280
0.252
0.197
0.180
0.137
0.126

9070
0.906
0.830
0.666
0.620
0.529
0.497
0.359
0.340
0.283
0.271

9075

1.05
0.946
0.751
0.690
0.587
0.545
0.394
0.369
0.305
0.290

9080
1.79
1.68
1.30
1.24
1.02
0.978
0.658
0.631
0.514
0.496

9085

2.01
1.86
1.44
1.35
1.12
1.06
0.714
0.678
0.552
0.527

Parallel Shaft Triple Reduction

GD2 at high speed shaft
Nominal
reduction ratio 9015
20
22.4
25
28
31.5
35.5
40
45
50
56
63
71
80
90

0.0034
0.0033
0.0029
0.0029
0.0019
0.0019
0.0017
0.0017

9025

9030

0.0084
0.0082
0.0076
0.0075
0.0046
0.0046
0.0043
0.0043

0.0115
0.0112
0.0099
0.0098
0.0061
0.0061
0.0055
0.0055
0.0036
0.0035
0.0033
0.0033

9035

0.0124
0.0122
0.0105
0.0104
0.0065
0.0064
0.0058
0.0057
0.0037
0.0037
0.0034
0.0034

9040
0.0223
0.0215
0.0191
0.0185
0.0134
0.0131
0.0121
0.0119
0.0076
0.0075
0.0071
0.0070

9045

0.0240
0.0229
0.0202
0.0194
0.0141
0.0137
0.0126
0.0123
0.0079
0.0077
0.0073
0.0072

Size of Reducer
9050 9055 9060
0.0539
0.0522
0.0437
0.0427
0.0305
0.0297
0.0263
0.0259
0.0173
0.0170
0.0157
0.0156

0.0574
0.0547
0.0458
0.0442
0.0319
0.0308
0.0272
0.0265
0.0179
0.0174
0.0160
0.0158

0.121
0.117
0.0996
0.0969
0.0655
0.0637
0.0568
0.0558
0.0347
0.0340
0.0315
0.0311

9065

0.130
0.122
0.105
0.100
0.0689
0.0659
0.0588
0.0571
0.0360
0.0349
0.0322
0.0316

9070
0.235
0.228
0.206
0.201
0.127
0.124
0.115
0.113
0.0700
0.0689
0.0655
0.0647

9075

0.249
0.239
0.214
0.208
0.132
0.128
0.118
0.116
0.0721
0.0706
0.0668
0.0659

9080
0.483
0.472
0.425
0.418
0.276
0.272
0.253
0.250
0.139
0.137
0.130
0.129

9085

0.507
0.492
0.441
0.431
0.285
0.279
0.259
0.255
0.142
0.140
0.133
0.131

Parallel Shaft Quadruple Reduction

GD2 at high speed shaft
Nominal
reduction ratio 9015

Common

Technical

D - 10

63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

9025

9030

0.0031
0.0031
0.0030
0.0030
0.0027
0.0027
0.0017
0.0017
0.0016
0.0016

9035

0.0032
0.0031
0.0030
0.0030
0.0027
0.0027
0.0017
0.0017
0.0016
0.0016

9040

0.0080
0.0080
0.0078
0.0078
0.0073
0.0073
0.0044
0.0044
0.0042
0.0042

9045

0.0081
0.0080
0.0079
0.0078
0.0074
0.0073
0.0044
0.0044
0.0042
0.0042

Size of Reducer
9050 9055 9060

0.0111
0.0110
0.0105
0.0104
0.0095
0.0095
0.0041
0.0041
0.0039
0.0039
0.0037
0.0037
0.0037
0.0035
0.0032

0.0113
0.0111
0.0106
0.0105
0.0096
0.0095
0.0042
0.0041
0.0040
0.0040
0.0037
0.0037
0.0037
0.0036
0.0032

0.0247
0.0244
0.0234
0.0232
0.0213
0.0212
0.0088
0.0087
0.0085
0.0084
0.0080
0.0079
0.0079
0.0077
0.0065

9065

0.0252
0.0248
0.0237
0.0234
0.0215
0.0213
0.0089
0.0088
0.0085
0.0085
0.0080
0.0080
0.0079
0.0077
0.0066

9070

0.0496
0.0491
0.0476
0.0473
0.0413
0.0411
0.0197
0.0196
0.0192
0.0191
0.0176
0.0175
0.0173
0.0172
0.0141

9075

0.0505
0.0499
0.0482
0.0478
0.0416
0.0414
0.0199
0.0198
0.0193
0.0192
0.0176
0.0176
0.0174
0.0172
0.0141

9080

0.0990
0.0983
0.0953
0.0948
0.0829
0.0827
0.0353
0.0351
0.0344
0.0343
0.0313
0.0312
0.0309
0.0302
0.0274

9085

0.101
0.0996
0.0963
0.0957
0.0835
0.0832
0.0357
0.0355
0.0346
0.0345
0.0314
0.0313
0.0310
0.0303
0.0274

TECHNICAL DATA GD2

Parallel shaft

Unit: kgf-m2
9090
3.46
3.36
2.77
2.70
1.96
1.92
1.29
1.27
1.01
0.998

9095
3.80
3.67
2.99
2.90
2.09
2.04
1.38
1.35
1.07
1.05

9100
7.10
6.86
5.28
5.12
4.06
3.96
2.63
2.56
2.04
2.00

9105
7.79
7.54
5.69
5.54
4.34
4.24
2.80
2.73
2.15
2.11

9110
13.3
12.4
9.91
9.37
7.62
7.25
5.16
4.93
4.02
3.87

Size of Reducer
9115 9118 9121

9126

9128

9131

Nominal
9136 reduction ratio
6.3
7.1
8
9
10
11.2
12.5
14
16
18
20
22.4

14.8
13.6
10.8
10.1
8.21
7.74
5.52
5.23
4.25
4.06

Unit: kgf-m2
9090
0.957
0.946
0.846
0.839
0.557
0.553
0.510
0.508
0.278
0.277
0.261
0.260
0.252

9095
0.991
0.978
0.868
0.859
0.571
0.566
0.520
0.516
0.284
0.282
0.264
0.263
0.255

9100
2.03
2.00
1.80
1.78
1.20
1.19
1.10
1.10
0.551
0.547
0.512
0.509
0.489

9105
2.09
2.07
1.84
1.83
1.23
1.22
1.12
1.11
0.562
0.558
0.519
0.517
0.495

9110
2.88
2.79
2.44
2.38
1.59
1.55
1.40
1.38
0.711
0.696
0.636
0.626
0.578

Size of Reducer
9115 9118 9121
3.02
2.91
2.53
2.46
1.65
1.60
1.44
1.41
0.735
0.716
0.651
0.639
0.587

9126

9128

3.15
2.62
2.27
1.70
1.67
1.48
1.33
0.863
0.776
0.666
0.607

4.80
4.58
3.77
3.62
2.52
2.43
1.95
1.89
1.47
1.43
1.24

4.92
4.69
3.85
3.69
2.57
2.48
1.98
1.92
1.49
1.45
1.25

9.35
8.96
6.86
6.62
4.57
4.41
3.24
3.14
2.51
2.44
1.96

9131
18.3
16.7
13.4
12.5
9.26
8.63
6.93
6.54
5.37
5.11
4.08

Nominal
9136 reduction ratio
18.7
17.0
13.6
12.7
9.40
8.73
7.01
6.60
5.42
5.15
4.11

20
22.4
25
28
31.5
35.5
40
45
50
56
63
71
80
90

Unit: kgf-m2
9090

0.270
0.263
0.263
0.245
0.245
0.0771
0.0770
0.0755
0.0754
0.0713
0.0712
0.0707
0.0680
0.0622

9095

0.272
0.265
0.264
0.246
0.246
0.0777
0.0775
0.0758
0.0757
0.0715
0.0714
0.0709
0.0681
0.0623

9100

0.432
0.419
0.418
0.385
0.385
0.159
0.158
0.155
0.155
0.147
0.147
0.146
0.141
0.118

9105

0.436
0.422
0.421
0.387
0.386
0.160
0.159
0.156
0.156
0.148
0.147
0.146
0.142
0.118

9110

0.493
0.471
0.467
0.425
0.423
0.271
0.269
0.170
0.169
0.159
0.158
0.155
0.150
0.125

Size of Reducer
9115 9118 9121

0.501
0.477
0.472
0.429
0.426
0.273
0.271
0.171
0.170
0.160
0.159
0.156
0.150
0.125

0.589
0.552
0.482
0.460
0.433
0.418
0.275
0.266
0.173
0.249
0.239
0.157
0.151
0.126

1.00
0.884
0.871
0.795
0.758
0.657
0.632
0.454
0.438
0.332
0.322
0.320
0.251

9126

1.01
0.892
0.878
0.800
0.762
0.661
0.634
0.455
0.440
0.333
0.323
0.321
0.251

9128

2.07
1.79
1.77
1.16
1.15
1.04
1.03
0.631
0.625
0.583
0.579
0.448
0.445

9131

2.85
2.45
2.35
2.10
1.88
1.47
1.32
1.04
0.948
0.930
0.685
0.673
0.562

Nominal
9136 reduction ratio

2.88
2.47
2.37
2.11
1.88
1.48
1.33
1.04
0.952
0.933
0.688
0.675
0.564

63
71
80
90
100
112
125
140
160
180
200
224
250
280
315
355
400
450
500

D - 11

TECHNICAL DATA Supplementary Dimension Drawing

9015 9055 / Right Angle Double, Triple / Parallel double
/ Horizontal, Vertical, Upright
FB

Q
FC

FS

FA

BS
C1

T1

C2

C3

T1

T1

DS

S2

L1

HP

S1

L1

K1

JS2

L1
K3

K2

Common

K4
P1

P1

Technical

Size
9015
9025
9030
9035
9040
9045
9050
9055

FS
118
130
143
143
165
165
185
185

FA
110
125
147
166
168
189
188
219

FB
325
385
445
495
510
570
590
660

FC
175
190
200
200
240
240
250
250

AS
140
155
175
194
205
226
225
256

BS
260
310
365
396
420
459
490
529

C
15
19
24
24
28
28
28
28

CA
25
30
40
40
48
48
55
55

HP
38
41
43
43
55
55
50
50

DS GS1 GS2 JS1

115 23
23
60
135 24
24
70
135 24
24
75
160 24
24
90
170 28
28
95
190 28
28 115
180 29
29
95
215 29
29 120

JS2
58
65
81
106
107
127
103
138

K1
50
55
60
60
75
75
75
75

Size
9015
9025
9030
9035
9040
9045
9050
9055

L1
38
45
54
54
66
66
68
68

L2
47
50
53
60
67
87
67
80

P1
50
50
53
53
67
67
67
67

Q
25
26
27
27
30
30
31
31

T1
35
40
50
50
60
60
60
60

S1
53
58
65
65
70
70
78
78

S2
23
26
24
24
28
28
32
32

RI
80
87.5
105
120
120
140
140
155

RJ
65
75
80
80
90
90
105
105

RK

C3
55
60
59
59
72.5
72.5
59
59

ES
110
130
140
140
145
145
150
150

D - 12

GS1

GS1

L2

RJ

RI

JS1

CA

ES

DS

RK

L2

T1

GS2

AS

70
70
72.5
72.5

F
175
200
214
214
250
250
280
280

C1
115
135
155
186
180
219
210
249

C2
79
92
109
109
126
126
148
148

K2
75
90
105
105
125
125
135
135

K3
85
110
80
80
100
100
100
100

K4
50
55
60
60
75
75
75
75

L1

TECHNICAL DATA Supplementary Dimension Drawing

9015 9055 / Right Angle Quadruple / Parallel Triple, Quadruple
/ Horizontal, Vertical, Upright
FB

Q
FC

FS

FA

HP

C1

C2

C3

C4

T1

T1

L1

L1

L1

S1
K1

RJ

K3

K2

P1

ES2

K4

9015 9035 Right Side)

T1

P1

GS2

GS1

L2

JS1

RI

JS2

S2

ES1

CA

DS

DS

L2

(9030~9055)

BS
C2

C1

GS2

AS
(9015,9025)

GS1

T1

T1

T1

L1

GS1

L1

9040 9055 Right Side)

Size
9015
9025
9030
9035
9040
9045
9050
9055

FS
118
130
143
143
165
165
185
185

FA
110
125
147
166
168
189
188
219

FB
325
385
445
495
510
570
590
660

FC
175
190
200
200
240
240
250
250

AS
140
155
175
194
205
226
225
256

BS
305
375
415
446
494
533
563
602

C
15
19
24
24
28
28
28
28

CA
25
23
44
44
56
56
56
56

HP
38
41
43
43
55
55
50
50

Size
9015
9025
9030
9035
9040
9045
9050
9055

L1
38
45
54
54
66
66
68
68

L2
47
50
53
60
67
87
67
80

P1
50
50
53
53
67
67
67
67

Q
25
26
27
27
30
30
31
31

T1
35
40
50
50
60
60
60
60

S1
53
58
65
65
70
70
78
78

S2
19
23
23
23
24
24
24
24

RI
80
87.5
105
120
120
140
140
155

RJ

80
80
90
90
105
105

DS GS1 GS2 JS1

115 23
23
60
135 24
24
70
135 24
24
75
160 24
24
90
170 28
28
95
190 28
28 115
180 29
29
95
215 29
29 120
F

214
170
214
214

C1
70
82.5
155
186
180
219
210
249

C2
20
281
63
63
74
74
89
89

JS2
58
65
72
97
100
120
103
138

C3

C4

85
85
99
99
118
118

80
80
90
90
96
96

K1
50
55
60
60
75
75
75
75

K2
75
90
105
105
125
125
135
135

K3
65
85
80
80
100
100
100
100

K4
50
55
60
60
75
75
75
75

ES1 ES2
110
130
120 170
120 170
140 200
140 200
150 202
150 202

D - 13

TECHNICAL DATA Supplementary Dimension Drawing

9060 9085 / Right Angle Double, Triple / Parallel Double
/ Horizontal, Vertical, Upright

FB

Q
FC

FS

FA

BS
C1

T1

C2

C3

T1

T1

DS

DS

L2

T1

GS2

AS

HP

JS2

RJ

S1
K1

L1

L1
K3

K2

K4
P1

P1

Common

Technical

Size
9060
9065
9070
9075
9080
9085

FS
210
210
235
235
255
265

FA
175
221
185
238
275
331

FB
300
300
370
370
370
370

FC
210
210
270
270
270
270

AS
251
290
283
330
325
369

BS
564
610
657
710
750
806

C
35
35
42
42
42
42

CA
75
75
85
85
100
100

HP
47
47
47
47
47
47

DS GS1 GS2 JS1

230 31
45 105
265 31
45 140
260 33
45 125
295 33
45 148
295 34
45 138
335 34
45 168

JS2
120
155
135
158
148
188

Size
9060
9065
9070
9075
9080
9085

L1
79
79
94
94
96
96

L2
100
135
110
145
120
160

P1
80
80
95
95
95
95

Q
40
40
40
40
45
45

T1
35
35
40
52
52
52

S1
72
72
72
72
82
82

S2
65
65
75
75
85
85

RI
160
175
175
190
190
215

RJ
115
115
138
138
160
160

F
330
330
380
380
420
420

ES
170
170
200
200
220
220

D - 14

GS1

GS1

L2

RI

JS1

CA

ES

S2

C1
245
291
285
338
330
386

C2
100
100
94.5
94.5
132
132

C3
138
138
203
203
188
188

K1
90
90
105
105
105
105

K2
160
160
190
190
190
190

K3
160
160
190
190
190
190

K4
90
90
105
105
105
105

L1

TECHNICAL DATA Supplementary Dimension Drawing

9060 9085 / Right Angle Quadruple / Parallel Triple, Quadruple
/ Horizontal, Vertical, Upright
FB

FS

FA

FC

AS

BS
C1

T1

C2

C3

C4

T1

GS2

T1

ES2
JS2

HP

L1

S1

L1

K1

K3

K2

K4

GS1

GS1

L2

RJ

RI

JS1

CA

ES1

S2

DS

DS

L2

T1

L1

P1

P1

Size
9060
9065
9070
9075
9080
9085

FS
210
210
235
235
255
265

FA
175
221
185
238
275
331

FB
300
300
370
370
370
370

FC
210
210
270
270
270
270

AS
251
290
283
330
325
369

BS
649
695
752
805
870
926

C
35
35
42
42
42
42

CA
75
75
85
85
100
100

HP
47
47
47
47
47
47

DS GS1 GS2 JS1

230 31
45 105
265 31
45 140
260 33
45 125
295 33
45 148
295 34
45 138
335 34
45 168

JS2
145
180
165
188
173
213

K1
90
90
105
105
105
105

Size
9060
9065
9070
9075
9080
9085

L1
79
79
94
94
96
96

L2
100
135
110
145
120
160

P1
80
80
95
95
95
95

Q
40
40
40
40
45
45

T1
35
35
40
52
52
52

S1
72
72
72
72
82
82

S2
65
65
75
75
85
85

RI
160
175
175
190
190
215

RJ
115
115
138
138
160
160

F
250
250
280
280
330
330

C4
110
110
120
120
146
146

ES1 ES2
170 232
170 232
200 267
200 267
220 305
220 305

C1
245
291
285
338
330
386

C2
100
100
94.5
94.5
132
132

C3
138
138
203
203
188
188

K2
160
160
190
190
190
190

K3
140
140
165
165
190
190

K4
90
90
105
105
105
105

D - 15

TECHNICAL DATA Supplementary Dimension Drawing

9090

9115/ Parallel Double, Triple, Quadruple / Horizontal

/ Right Angle Double, Triple, Quadruple / Horizontal
FB

Q
FC

FS

FA

T1

BS

L1

Size
9090
9095
9100
9105
9110
9115

FA
350
380
435
470
525
575

FB
370
370
370
370
370
370

FC
270
270
270
270
270
270

AS
345
375
375
410
420
470

BS
975
1005
1095
1130
1240
1290

K1

C
42
42
48
48
56
56

DS
315
340
355
380
400
425

GS
45
45
46
46
48
48

K2

JS1
155
180
185
210
230
255

JS2
152
177
170
195
202
227

JS3
260
285
305
330
350
375

K1
230
245
265
270
285
315

K3

K2
240
225
290
260
325
305

K3
170
170
190
190
310
310

L1
96
106
110
120
119
129

Q
45
45
45
45
45
45

T1
50
50
55
55
60
60

9115/ Parallel Double, Triple, Quadruple / Vertical

/ Right Angle Double, Triple, Quadruple/Vertical

HP

FS

9090

FS
330
330
375
375
407
407

L1

JS2

GS

JS1

JS3

DS

AS

DS

T1

K5
C4 C3

C2

C1

L2

L2

S3

WB1

RJ

RK

S2

RI

WB2

S4

Common

Technical

K4

S1

Size
9090
9095
9100
9105
9110
9115

D - 16

FS
330
330
375
375
407
407

HP
42
42
43
43
44
44

K4
170
185
190
215
210
235

K5
190
215
220
240
240
270

L2
130
140
150
160
170
180

RI
215
235
235
260
265
280

RJ
173
173
200
200
213
213

RK
133
133
145
145
160
160

S1
90
80
85
80
90
85

S2
130
140
145
155
150
150

S3
90
90
90
90
105
105

S4
90
90
100
100
100
100

C1
378
408
425
459
483
532

C2
262
262
299
299
341
341

C3
82
82
91
91
90
90

C4 WB1 WB2
225 290 430
225 290 430
260 370 500
260 370 500
261 370 500
261 370 500

TECHNICAL DATA Supplementary Matters to Hollow Shaft

Feature and Benets
PARAMAX DRIVE units have a number of outstanding features compared to conventional solid shaft speed
reducers.
1. There is no necessity for a large sized coupling, permitting substantial cost reduction.
2. It can be directly mounted onto the driven shaft, eliminating the necessity for foundation
working for speed reducer installation and alignment operation.
3. Any unit is designed for compactness and ease of operation.

How to Install Unit

a. Torque Arm (Option)
The hollow shaft type PARAMAX DRIVE is secured with the torque arm
to prevent it from being turned by the counter force.
A torque arm is subjected to a compression or tensile load depending
upon the direction of rotation of the slow speed shaft, and it must have a
sufcient strength against shock loading at the start and during operation.
Being prepared as a optional accessory, the torque arm is designed in
consideration of such loading conditions.
Please order us, if it is necessary.
The construction and strength of the torque arm mounting legs
must be determined in consideration of impact load.

Torque

Arm

(DRG D1701)

b. How to Use Torque Arm

(1) When the torque arm is used with the speed reducer housing
The torque arm must be mounted in an installation hole closer
to the application machine. (For torque arm mounting dimensions, refer to the dimension drawing.)
(2) When the torque arm is used with the common base plate
The torque arm must be mounted in a position as far from the
low speed shaft as possible.
(DRG D1702)

Torque Arm Dimensions

A TR

Bolt

PR

(DRG D1703)
Use bolt and nut classied as JIS strength class 8.8

Size

M
(nut)

max

TR

9015
9025
9030
9035
9040
9045
9050
9055
9060
9065
9070
9075
9080
9085
9090
9095
9100
9105
9110
9115

13.1
16.1
18.9
18.9
21.7
21.7
21.7
21.7
32.2
32.2
38.2
38.2
38.2
38.2
38.6
38.6
47.6
47.6
48.5
48.5

140
170
200
200
240
240
240
240
310
310
370
370
370
370
370
370
420
420
460
460

M12
M16
M20
M20
M24
M24
M24
M24
M30
M30
M36
M36
M36
M36
M36
M36
M42
M42
M48
M48

35
40
50
50
60
60
60
60
85
85
95
95
95
95
95
95
100
100
110
110

22
25
28
28
30
30
32
32
35
35
40
52
52
52
50
50
55
55
60
60

PR

S (bellevile spring)
DIN2093(nom.)
Qty
A50
2X2
A50
2X3
A63
2X3
A63
2X3
A80
2X2
A80
2X2
A80
2X2
A80
2X2
A100
2X3
A100
2X3
A100
2X4
A100
2X4
A100
2X4
A100
2X4
A125
2X3
A125
2X3
A125
2X4
A125
2X4
A160
2X3
A160
2X3

D - 17

TECHNICAL DATA Hollow Shaft Related Dimensions

1. Hollow Shaft Dimensions
Shrink Disk Coupling

Detail A

(DRG D1801)
Size

Unit: mm

Shrink Disk

9015

MODEL
(note 1)
TAS3091.4-080

9025

TAS3081. -090

9030

TAS3091.1-100

9035

TAS3093. -110

9040

Hollow Shaft

Clamping Bolt

Driven Shaft

Ds

ZS

TA
Nm

LZ

LR

LV

N-ZY

DZ

LS

dw

d1

L3

L4

38

M8

35

135

328

14

4 - M6

70

15

161

60h6

61

D1
min
78

L2

145

D
h7
63

L1

80

325

240

80

2.5

Z
(Deep)
M20 (30)

90

155

39

M8

35

145

358

14

4 - M6

80

17

176

70h6

71

73

88

355

270

80

2.5

M20 (30)

100

170

54

M10

59

160

393

14

4 - M6

90

20

209

80h6

81

83

98

390

295

90

2.5

M20 (30)

110

185

60

M10

70

160

403

14

4 - M6

97

20

244

85h6

86

88

103

390

295

90

2.5

M24 (35)

TAS3081. -125

125

215

54

M10

70

180

448

20

4 - M8

110

17

244

95h6

96

98

113

445

335

110

2.5

M24 (35)

9045

TAS3093. -140

140

230

74

M12

120

180

463

20

4 - M10 124

17

277

105h6

106

108

123

460

355

110

2.5

M24 (35)

9050

TAS3093. -140

140

230

74

M12

120

200

503

22

4 - M10 124

17

277

105h6

106

108

123

500

380

110

2.5

M24 (35)

9055

TAS3091. -165

165

290

88

M16

250

205

528

27

4 - M12 146

17

314

120h6

121

123

138

525

385

120

2.5

M24 (35)

9060

TAS3091. -165

165

290

88

M16

250

230

583

4.5

27

4 - M12 146

12

322

125h6

126

128

143

580

435

130

M24 (35)

9065

TAS3091. -175

175

300

88

M16

250

235

594

4.5

26

4 - M12 157.5 21

349

140h6

141

143

158

589

450

130

M30 (45)

9070

TAS3081. -185

185

330

86

M16

290

260

644

4.5

26

4 - M12 167

21

349

145h6

146

148

163

640

475

160

M30 (45)

9075

TAS3081. -200

200

350

86

M16

290

265

651

4.5

26

4 - M12 177

21

379

155h6

156

158

173

646

475

160

M30 (45)

9080

TAS3081. -220

220

370

104

M16

290

285

714

4.5

26

4 - M12 195

21

401

170g6

171

173

188

709

520

190

M30 (45)

9085

TAS3081. -240

240

405

109

M20

570

285

714

4.5

27

4 - M12 210

21

456

180g6

181

183

198

709

520

190

M30 (45)

9090

TAS3081. -240

240

405

109

M20

570

350

844

27

6 - M12 215

21

451

190g6

191

193

212

840

635

200

4.5

M36 (55)

9095

TAS3081.1-260

260

440

120

M20

535

350

859

27

6 - M12 230

14

450

200g6

201

203

222

855

640

205

4.5

M36 (55)

9100

TAS3081.1-260

260

440

120

M20

535

390

934

27

6 - M12 235

21

491

210g6

211

213

234

930

705

215

4.5

M36 (55)

9105

TAS3081.1-280

280

460

134

M20

535

390

949

27

6 - M12 250

19

480

220g6

221

223

244

945

715

225

4.5

M36 (55)

9110

TAS3081.1-300

300

485

142

M20

535

420 1030

32

6 - M16 270

15

551

240g6

241

243

263 1025 770

245

4.5

M36 (55)

9115

TAS3091. -320

320

520

184

M20

490

420 1065

32

6 - M16 285

15

550

250g6

251

253

273 1060 785

245

4.5

M36 (55)

Note: 1 Shrink disk (made by SCHFER) type No.

2 For vertical types, thrust washer is necessary to prevent the reducer move when loosening the locking bolt ZS.

9015~9055
L/ 2

A
X Js9/h9

L4

L3

L1

Common

LS

(DRG D1802)
Driven Shaft

Safety Cover

LS

Unit: mm

Locking Screw Locking Distance Ring

Thread Size X Body
O.D. X W
Length DRG D1802(f) DRG D1906,1910(h)

7.5 161

D
j6
55

D1
min
70

10

190

65

80

M24

9.5

230

75

M24

10

260

85

M30

10

260

90

105

310

260

100

40

180

25

14

2.5

M24(35)

M24X60

90X4

M30

10

300

105

120

310

260

100

40

180

28

16

10

2.5

M24(35)

M24X65

388

M30

10

300

105

120

350

300

110

45

220

28

16

10

2.5

M24(35)

M24X65

105X6
105X6

388

M30

10

330

115

130

350

300

110

45

220

32

18

11

2.5

M24(35)

M24X65

115X6

470

4.5

M30

47

340

125

140

123

445

395

90

260

32

18

11

M24(35)

M24X80

9065

480

4.5

M36

54

350

145

160

143

455

405

100

265

36

20

12

M30(45)

M30X100

125X25
145X30

9070

530

4.5

M36

54

370

145

160

143

500

445

120

310

36

20

12

M30(45)

M30X100

9075

530

4.5

M36

54

400

150

165

148

500

445

120

365

40

22

13

M30(45)

M30X100

9080

570

4.5

M36

54

400

165

180

163

540

480

125

370

40

22

13

M30(45)

M30X100

9085

570

4.5

M36

54

450

175

190

173

540

480

125

385

45

25

15

M30(45)

M30X100

LG

LH

LR

9015

270

240

258

M24

9025

300

265

286

M24

9030

330

290

314

9035

330

290

315

9040

360

314

340

9045

370

316

348

9050

410

356

9055

410

356

9060

LS

D2
j6

L5
L2

LH

Hollow Shaft

L3
L1
LG

Size

- 0.2

D1

L5

L2

Technical

Z1

D - 0.4

U
(except 9015)

- 0.2

D - 0.4

L4

B-B

D2

D1

Detail A

Z1

1.6

R
LR(45 )

9060~9085
L/ 2

Key Coupling

30

L5
min
115

16

10

2.5

Z1
(Deep)
M20(30)

35

125

18

11

2.5

M20(30)

M20X50

90

35

145

22

14

2.5

M20(30)

M20X55

90

35

160

22

14

2.5

M20(30)

M20X55

L1

L2

L3

L4

235

200

70

260

220

80

90

285

240

100

285

240

Note: 1 The key and keyway conform to JIS B 1301-1996(ISO)"Sunk keys and keyways" parallel keys (regular class)

2 The locking screw and distance ring will not be supplied. Please prepare, if they are necessary.

3 Dimension from center of housing to shaft end is L/2.

D - 18

M20X50

55X5
65X5
75X5
85X5

145X30
150X30
165X30
175X30

TECHNICAL DATA Hollow Shaft Related Dimensions

2. Shrink Disk Coupling / Mounting & Removal Procedure
Mounting Procedure (DRG D1901)
(1) Clean and degrease contact surface (a) and (c).
(2) Smear surface (c) with "Molykote 321" or its equivalent.
However, keep surface (a) as clean as possible (no grease).
(3) Slide O-ring (b) onto the shaft.(Size 9090 to 9115)
(4) Mount the reducer on the driven shaft and screw nuts (e) until faces (g)
and (h) make contact.
(5) Set the shrink disk (k) at dimensions (LV). Tighten locking bolt (ZS) at
specied torque (TA) (using a torque wrench).

(DRG D1901)

Removal Procedure (DRG D1902)

(1) Loosen locking bolt (ZS) and remove shrink disk (k).
(2) Set thrust washer (f) and hexagon head bolt (n).
Remove the reducer from the driven shaft using bolt (m).
Note: Parts (d), (e), (f), (ZY), (m) and (n) are optional.
Order these as required.

( ZY )

( n)

( f)( m )

(DRG D1902)

3.Key Coupling / Mounting & Removal Procedure

Size 9015 to 9055
Mounting Procedure (DRG D1903)
The Hollow shaft bore is provided with retaining ring (d).
Ring (d) is the essential component for mounting, securing, and removing the unit.
(1) Smear surface of the shaft (e) with "molykote 321" or its equivalent.
(2) Turn nut (b) and slide the reducer over the driven shaft.
Use plain washer (c), if they are necessary.

( d)
( c)
( b)
( a)

( e)

(DRG D1903)
( f)

Securing (DRG D1904)

(1) After mounting the reducer on the driven shaft, x bolt (f). (Bolt (f) is not
supplied with the unit.)
(2) The bore should be protected by cover (g).

( g)

(DRG D1904)

Removal Procedure (DRG D1905)

(1) Remove ring (d), mount bolt (n), and reset ring (d).
Attach bolt (J) to ring (d), and turn bolt (J) to disconnect the hollow shaft
from the driven shaft.
Screw size, refer to the lower table (Z) of the page D-18.

( d)

(DRG D1905) ( n )

Special Cases (DRG D1906)

( f)

(1) If the driven shaft has no shoulder (DRG D1906) when mounting,
provide a distance ring (h) for xing in place. (Ring (h) is not supplied
with the unit).

Size 9060 to 9085

Mounting Procedure (DRG D1907)
The Hollow shaft end is provided with thrust washer (d).
Thrust washer (d) is the essential component for mounting, securing, and
removing the unit.
(1) Smear surface of the shaft (e) with "molykote 321" or its equivalent.
(2) Turn nut (b) and slide the reducer over the driven shaft.

( g)

(DRG D1906) ( h )
( d)

(e)

( b)
( a)

(DRG D1907)
( f)

Securing (DRG D1908)

(1) After mounting the reducer on the driven shaft, x bolt (f). Bolt (f) is not
supplied with the unit.)
(2) The bore should be protected by cover (g)

Removal Procedure (DRG D1909)

( J)

( g)

(DRG D1908)

(1) Remove thrust washer (d), mount bolt (n), and reset thrust washer (d).
Attach bolt (J) to thrust washer (d), and turn bolt (J) to disconnect the
hollow shaft from the driven shaft.
Screw size, refer to the lower table (Z) of the page D-18.

Special Cased (DRG D1910)

( J)

(DRG D1909)

( n)

(1) If the driven shaft has no shoulder (DRG D1906) when mounting,
provide a distance ring (h) for xing in place.(Ring (h) is not supplied
with the unit.)
Distance ring dimension, refer to the lower table of the page D-18.
Note : Parts (a),(b),(c),(n) and (J) are optional. Order these as required.

( f)
( g)

(DRG D1910) ( h)

D - 19

TECHNICAL DATA Cooling Fan Dimension

FA

FB

9085 Right Angle Double Reduction

FH

9015

FD
FC
FF

FA

FB

9115 Right Angle Double Reduction

FH

9090

FA

FD
FC
FF

Common

Technical

FA

Size

FA

FB

FC

FD

FF

FH

Size

FA

FB

FC

FD

FF

FH

9015

250

125

50

30

477

145

9095

680

250

135

90

1303

270

9025

270

140

50

30

515

160

9105

760

250

175

130

1459

270

9030

300

140

80

52

593

160

9115

820

250

175

130

1672

270

9035

300

140

80

52

624

160

9040

340

160

80

52

653

180

9045

340

160

80

52

692

180

9050

380

160

80

52

703

180

9055

380

160

80

52

742

180

9060

440

160

105

65

800

180

9065

440

160

105

65

846

180

9070

490

200

105

65

900

220

9075

490

200

105

65

953

220

9080

540

225

105

60

1020

245

9085

540

225

105

60

1076

245

Sufficient space must be allowed for air intake when mounting the safety guards for the
coupling or other component.
The split fan hood is prepared as a optional accessory for conducting maintenance work
on a large coupling.Refer to the "PARAMAX 9000 Series Option Catalog No.G2052E".
D - 20

TECHNICAL DATA Cooling Fan Dimension

FA

9085 Right Angle Triple Reduction

FB
FH

9015

FD
FC
FF

FA

FB

9115 Right Angle Triple Reduction

FH

9090

FA

FD
FC
FA

FF

Size

FA

FB

FC

FD

FF

FH

Size

FA

FB

FC

FD

FF

FH

9030

300

125

50

30

626

145

9090

680

200

105

65

1255

220

9035

300

125

50

30

657

145

9095

680

200

105

65

1285

220

9040

340

125

50

30

686

145

9100

760

225

105

60

1414

245

9045

340

125

50

30

725

145

9105

760

225

105

60

1448

245

9050

380

140

50

22

786

160

9110

820

225

135

90

1594

245

9055

380

140

50

22

825

160

9115

820

225

135

90

1643

245

9060

440

160

80

52

887

180

9065

440

160

80

52

933

180

9070

490

160

80

52

975

180

9075

490

160

80

52

1028

180

9080

540

160

105

65

1111

180

9085

540

160

105

65

1167

180

Note) Consult us for cooling fan dimension of size 9118 and 9136.

D - 21

TECHNICAL DATA Cooling Fan Dimension

9085 Parallel Double Reduction

9090

9115 Parallel Double Reduction

FF
FD
FC

FC

FD

FF

FG

FG

9015

FB
FH

FE

FE

FE

FE

FB
FH

FA2

FA1

FA2

FA1

FA

FA

When tightening installation bolt,

remove fan hood.

Common

Technical

Size

FA1 FA2

FA

FB

FC

FD

FE

FF

FG

FH

Size

FA1 FA2

FA

FB

FC

FD

FE

FF

FG

FH

9015

129

129

258

125

50

30

130

181

32.5

145

9090

465

277

742

250

135

90

345

410

65

270

9025

143

143

286

140

50

30

150

196

27.5

160

9095

465

277

742

250

135

90

345

410

65

270

9030

169

169

338

140

80

52

155

217

27.5

160

9100

515

314

829

250

175

130

395

455

65

270

9035

169

169

338

140

80

52

180

217

27.5

160

9105

515

314

829

250

175

130

395

455

65

270

9040

188

188

376

160

80

52

195

232

21.5

180

9110

565

356

921

250

175

130

445

485

65

270

9045

188

188

376

160

80

52

215

232

21.5

180

9115

565

356

921

250

175

130

445

485

65

270

9050

208

208

416

160

80

52

205

251

28.5

180

9055

208

208

416

160

80

52

240

251

28.5

180

9060

240

240

480

200

105

65

260

295

40

220

9065

240

240

480

200

105

65

295

295

40

220

9070

274

274

548

225

105

65

295

320

44

245

9075

274

274

548

225

105

65

330

320

44

245

9080

296

296

592

225

135

95

330

339

52

245

9085

296

296

592

225

135

95

370

339

52

245

Sufficient space must be allowed for air intake when mounting the safety guards for the coupling
or other component.
The split fan hood is prepared as a optional accessory for conducting maintenance work on a
large coupling.Refer to the "PARAMAX 9000 Series Option Catalog No.G2052E".
D - 22

TECHNICAL DATA Cooling Fan Dimension

9085 Parallel Triple Reduction

9090

9115 Parallel Triple Reduction

FD

FD
FC

FB
FH

FE

FE

FE

FE

FB
FH

FA2

FC

FF

FF

FG

FG

9015

FA1

FA2

FA1

FA

FA

When tightening installation bolt,

remove fan hood.

Size

FA1 FA2

FA

FB

FC

FD

FE

FF

FG

FH

Size

FA1 FA2

FA

FB

FC

FD

FE

FF

FG

FH

9015

111

111

222

125

30

10

105

180

32.5

145

9090

268

474

742

200

105

65

345

405

65

220

9025

129

129

258

125

30

10

125

194

27.5

145

9095

268

474

742

200

105

65

345

405

65

220

9030

140

140

280

125

50

30

125

211

27.5

145

9100

289

540

829

225

105

65

395

450

65

245

9035

150

150

300

140

50

22

150

219

27.5

160

9105

289

540

829

225

105

65

395

450

65

245

9040

170

170

340

140

50

22

165

234

21.5

160

9110

339

582

921

225

135

95

445

480

65

245

9045

170

170

340

140

50

22

185

234

21.5

160

9115

339

582

921

225

135

95

445

480

65

245

9050

172

172

344

140

80

52

170

252

28.5

160

9055

172

172

344

140

80

52

205

252

28.5

160

9060

199

199

398

160

80

52

220

277

40

180

9065

199

199

398

160

80

52

255

277

40

180

9070

221

221

442

160

80

52

250

302

44

180

9075

221

221

442

160

80

52

285

302

44

180

9080

247

247

494

200

105

65

280

340

52

220

9085

247

247

494

200

105

65

320

340

52

220

Note) Consult us for cooling fan dimension of size 9118 and 9136.

D - 23

TECHNICAL DATA Option Dimension

9015

9055 Right Angle Double, Triple, Quadruple

/ Parallel Double, Triple, Quadruple

Air Breather

Y1

Y2

Size

Y1

Y2

9015

216

135

9025

233

149

9030

235

173

[9015~9030 Reduction Ratio 6.3~7.1]

FY

Y1

Y2

[9015~9030 Reduction Ratio 6.3~7.1

9035~9055 Reduction Ratio All]

Size

Y1

Y2

FY

9015

162

35

129

9025

182

25

141

9030

187

154

9035

212

154

9040

227

30

171

9045

247

* 30

171

9050

232

25

191

9055

267

191

* Double and triple reduction

right angle, and double
reduction parallel is 29mm.

Drain Valve

GS

Common

Technical

CX

D - 24

Size

CX

GS

9015

122

23

9025

122

24

9030

119

24

9035

119

24

9040

133

28

9045

133

28

9050

133

29

9055

133

29

TECHNICAL DATA Option Dimension

9015

9055 Right Angle Double, Triple, Quadruple

/ Parallel Double, Triple, Quadruple

Air Breather

Y1

Y2

Size

Y1

Y2

9015

110

35

9025

130

25

9030

135

9035

160

9040

175

30

9045

195

* 30

9050

180

25

9055

215

* Double and triple reduction

right angle, and double
reduction parallel is 29mm.

HP

Drain Valve

CX
Size

CX

HP

9015

122

38

9025

117

41

9030

109

43

9035

109

43

9040

127

55

9045

127

55

9050

119

50

9055

119

50

Parallel Triple, Quadruple

Right Angle Quadruple

Parallel Double
Right Angle Double, Triple

D - 25

TECHNICAL DATA Option Dimension

9015

9055 Right Angle Double, Triple, Quadruple

/Parallel Double, Triple, Quadruple

Air Breather

Y1

Size

Y1

9015

112

9025

131

9030

136

9035

161

9040

172

9045

192

9050

181

9055

216

Drain Valve

CX

Common

Technical

BX

D - 26

Size

BX

CX

9015

260

135

9025

277

149

9030

279

173

9035

297

192

9040

333

205

9045

353

226

9050

343

224

9055

365

255

TECHNICAL DATA Option Dimension

9060

9085 Right Angle Double, Triple, Quadruple

/Parallel Double, Triple, Quadruple

Air Breather

Y1

FY
Size

Y1

FY

9060

281

211

9065

316

211

9070

315

236

9075

350

236

9080

350

256

9085

390

256

[ 9060~9085 Double reduction right angle and

double reduction parallel]

Oil Level Gauge

CW

Size

CW

9060

318

9065

357

9070

355

9075

402

9080

397

9085

441

GS

Drain Valve

Size

CX

GS

9060

170

31

9065

170

31

9070

155

33

9075

155

33

9080

155

34

9085

157

34

CX

D - 27

TECHNICAL DATA Option Dimension

9060

9085 Right Angle Double, Triple, Quadruple

/Parallel Double, Triple, Quadruple

Y1

Air Breather

Size

Y1

9060

229

9065

264

9070

263

9075

298

9080

298

9085

338

Oil Level Gauge

Note) Oil level gauge is not max dimension.

Drain Valve

HP

Common

Technical

CX

D - 28

Size

CX

HP

9060

120

47

9065

120

47

9070

120

47

9075

120

47

9080

110

47

9085

110

47

TECHNICAL DATA Option Dimension

9060

9085 Right Angle Double, Triple, Quadruple

/Parallel Double, Triple, Quadruple

Air Breather
Y1

Size

Y1

9060

234

9065

264

9070

267

9075

302

9080

301

9085

341

Oil Level Gauge

Note) Oil level gauge is not max dimension.

Right Angle Double, Triple / Parallel Double

Right Angle Quadruple / Parallel Triple, Quadruple

CX

Drain Valve

Size

BX

CY

9060

335

214

9065

335

253

9070

360

251

9075

360

298

9080

380

283

9085

380

327

BX

D - 29

TECHNICAL DATA Option Dimension

9090

9115 Right Angle Double, Triple, Quadruple

/Parallel Double, Triple, Quadruple

HW

Air Breather

Size

HW

9090

839

9095

889

9100

939

9105

989

9110

1039

9115

1089

Oil Level Gauge

CW
Size

CW

9090

435

9095

465

9100

475

9105

510

9110

525

9115

575

Drain Valve

GS

CX

D - 30

CX

GS

162

45

9095

162

45

9100

162

46

9105

162

46

9110

162

48

9115

162

48

CX

GS

Common

Technical

Size
9090

Size

CX

GS

9095R2

172

62

9105R2

172

62

9115R2

172

69

TECHNICAL DATA Option Dimension

9090

9115 Right Angle Double, Triple, Quadruple

/ Parallel Double, Triple, Quadruple

Y1

Air Breather

VW

Y1

Y2

626

90

315

9095

626

90

345

9100

706

100

355

9105

706

100

390

9110

766

100

405

9115

766

100

440

VW

Y2

Size
9090

Oil Level Gauge

CW

Size

CW

9090

405

9095

430

9100

455

9105

480

9110

505

9115

530

HP

Drain Valve

CX

Size

CX

HP

9090

162

42

9095

162

42

9100

162

43

9105

162

43

9110

162

44

9115

162

44

D - 31

TECHNICAL DATA Motor Terminal Box

Drive Unit

Right Angle Shaft Horizontal Mounting

Right Angle Shaft Vertical Mounting

Common

Technical

1. Direction shows lead wire outside of terminal box.

2. The terminal box mounting direction can be changed in units of 90 degree in our factory.
Please specify the direction when placing an order.

D - 32

TECHNICAL DATA Motor Terminal Box

Drive Unit

Right Angle Shaft Upright Mounting

Parallel Shaft Vertical Mounting

1. Direction shows lead wire outside of terminal box.

2. The terminal box mounting direction can be changed in units of 90 degree in our factory.
Please specify the direction when placing an order.

D - 33



TECHNICAL DATA Motor Flange Dimension

IEC, JEM Standard

C
D
E

4-LZ

DL

MS

LB
A

PC

45

(DRG D3401)
C
D
E

8-LZ

PC
D
MS

22.5

LB

LA

22.5

(DRG D3402)

(JEM Standard)

Common

Technical

kWxP
5.5 4P
7.5 4P
11 4P
15 4P
18.5 4P
22 4P
30 4P
37 4P
45 4P
55 4P

Motor Flame
132S
132M
160M
160L
180M
180M
180L
200L
200L
225S

A
315
315
350
350
400
400
400
450
450
550

LB
230
230
250
250
300
300
300
350
350
450

C
84
84
114
114
144
144
144
144
144
144

D
48
48
32
32
62
62
62
48
48
32

E
7
7
7
7
7
7
7
7
7
7

MS
38
38
42
42
48
48
55
60
60
65

H
41.3
41.3
45.3
45.3
51.8
51.8
59.3
64.4
64.4
69.4

I
10
10
12
12
14
14
16
18
18
18

LA
265
265
300
300
350
350
350
400
400
500

LZ
Thread Length
4-M12
22
4-M12
22
4-M16
32
4-M16
32
4-M16
62
4-M16
62
4-M16
62
8-M16
32
8-M16
32
8-M16
32

Fig.
D3401
D3401
D3401
D3401
D3401
D3401
D3401
D3402
D3402
D3402

A
315
315
350
350
350
350
400
450
450
550

LB
230
230
250
250
250
250
300
350
350
450

C
84
84
114
114
144
144
144
144
144
144

D
48
48
32
32
62
62
62
48
48
32

E
7
7
7
7
7
7
7
7
7
7

MS
38
38
42
42
48
48
55
60
60
65

H
41.3
41.3
45.3
45.3
51.8
51.8
59.3
64.4
64.4
69.4

I
10
10
12
12
14
14
16
18
18
18

LA
265
265
300
300
300
300
350
400
400
500

LZ
Thread Length
4-M12
22
4-M12
22
4-M16
32
4-M16
32
4-M16
62
4-M16
62
4-M16
62
8-M16
32
8-M16
32
8-M16
32

Fig.
D3401
D3401
D3401
D3401
D3401
D3401
D3401
D3402
D3402
D3402

(IEC Standard)
kWxP
5.5 4P
7.5 4P
11 4P
15 4P
18.5 4P
22 4P
30 4P
37 4P
45 4P
55 4P

Motor Flame
132S
132M
160M
160L
180M
180L
200L
225S
225M
250M

If no specification is made, production will follow JEM Standard.

D - 34

D - 35



TECHNICAL DATA Formula of Drive System

SI Units

1. Revolving Speed N(r/min), Velocity V(m/s)

V(m/s)

N
(m/s)
60
DWheel Diameter (m)
3.14
V = D

N
r/min D
m

2. Torque T (Nm)
F
N

T = F R (N m)
FLoadN
RWheel Radius (m)

R
m
T
N m

3. Power P(kW)

P=

V(m/s)
F
N

(kW)

FLoadN
VVelocity (m/s)

4. Power P(kW), Torque T(Nm), Revolving Speed N(r/min)

Common

Technical

FV
1000

P=

NT
9550

(kW), T =

9550 P
( N m)
N

F
N
R
m

FV
1000

P=

P=

V(m/s)

(kW), V = 2 R

F 2 R N
60
1000

2
1000 60

Since T = F R

N
r/min
F : Load (N)

D - 36

P=

2
1000 60

NT=

N
(m/s)
60

N T (kW)
9550

N F R (kW)

TECHNICAL DATA Formula of Drive System

SI Units

5. Acceleration Force FA (N)

V2 (m/s)

V1 (m/s)

FA (N)

m (kg)
tA (s)

FA = m = m V2 - V1 (N)
tA
V
= m 2 - V1
tA
m : Weight (kg)
: Acceleration (m/s2)
tA : Acceleration Time (s)

6. Acceleration Torque TA (Nm)

TA = FA R ,
V2 = D

FA (N)

V1 (m/s)

V2 (m/s)

N2
r/min

N2
60

V2 - V1
tA
V1 = D

N1
60

D =2R
2 R
60

TA = m

R
m
N1
r/min

FA = m

tA (s)
=

D
m

tA

2 m R

(N 2 - N1)

60
m R2
9.55

N2 - N1
tA
N2 - N1
tA

(N m)

Since m R2 is J (Moment of Inertia : kg-m2)

TA=

J
9.55

N2 - N1
tA

(Nm)

7. Synchronized Revolving Speed of AC Motor N0 (r/min)

No =

120 f
(r/min)
P

f : Power Supply Frequency (Hz)

P : No. of Motor Poles

8. Rated Revolving Speed of AC Motor N(r/min)

N = No(1 - S) (r/min)
No : Synchronized Revolving Speed (r/min)
S : Slippage

D - 37

Warranty
Warranty
Period

The warranty period for the Products shall be 18 months after the commencement of delivery or 18
months after the shipment of the Products from the seller's works or 12 months from the Products
coming into operation, whether comes first.

Warranty
Condition

In Case that any problems, troubles or damages on the Products arise due to the defects in the
Products during the above "Warranty Period" , although the Products are appropriately and properly
installed in, connected or combined to the equipment or machines, or maintained in accordance with
the maintenance manual and are properly operated under the conditions as described in the catalogue
or otherwise as agreed upon in writing between the Seller and the Buyer or its customers, the Seller will
provide, at its sole discretion, appropriate repair or replacement on the Products free of charge, except
as stipulated in the "Exception for Warranty" as described below.
However, in the event that the Products is installed in, connected or combined to or integrated into the
equipment or machines, the Seller shall not reimburse the costs for removal or re-installation of the
Products or other incidental costs related thereto and any lost opportunity, loss of profit or any other
incidental or consequential losses or damages incurred by the Buyer or its customers.

Exception
for
Warranty

D - 38

Notwithstanding the above warranty, the warranty as set forth herein shall not be applied to the
problems, troubles or damages on the Products which are caused by:
1. installations, connections, combinations or integration of the Products in or to the other equipment
or machines, which are rendered by any person or entity other than the Seller,
2. the insufficient maintenance or improper operation by the Buyer or its customers, such that the
Product is not appropriately maintained in accordance with the maintenance manual provided or
designated by the Seller,
3. the improper use or operation of the Products by the Buyer or its customers which are not informed
to the Seller, including, without limitation, the Buyer's or its customers' operation of the Products
not in conformity with the specifications, or use of the lubrication oil in the Products which is not
recommended by the Seller,
4. troubles, problems or damages on any equipment or machines in or to which the Products are
installed, connected or combined or installed, or any specifications particular to the Buyer or its
customers.

SAFETY PRECAUTIONS
Strictly observe the safety rules for the installation place and the equipment to use.
(Industrial Safety and Health Law, Technical Standard for Electric Facilities, Extension Rules, Plant Explosion
Guidelines, Building Standards Law, etc.)
Carefully read the maintenance manual before use. If the maintenance manual is not on hand, make a request
for one to the distributor at which you purchased the product or to our sales department. The maintenance
manual should be sent to the actual user.
Select an appropriate product that matches the operating environment and usage.
Install a protective equipment on the machine side when the machine is used for transportation of passengers or
for elevators, escalators, and dumbwaiters.
When the machine is used for food processing equipment and others that are susceptible to oil, install an oil pan
or other damage preventive devices in case of oil leakage due to failure or termination of service life.

D - 39