Professional Documents
Culture Documents
9.7 Find voltage vL in the circuit of Figure P9.7, where D is an ideal diode, for positive and negative values of vS. Sketch a plot of vL versus vS. 1. The diode is given as ideal i.e. we can replace it with a switch such that At vD < 0 At vD 0 (negative) (positive) => the switch is open and, => the switch is closed
2. For computing vL: find equivalent resistance replacing the diode with a switch as per the above conditions and then computing the voltage across RL 3. Show, graphically, how vL will change with varying values of vs.
V1 =
R1 .V S R1+ RS
At v1 < 0
At v1 >= 0
KCL at node 1 iS - i1 - iL = 0
VL R1 || R L = VS R S + R1 || R L
Where v is the offset voltage. 2. For computing vL: replace the diode with a switch with a voltage source (of offset voltage value) as per the above conditions and then compute the voltage across RL 3. Show, graphically, how vL will change with varying values of vs. 4. Another example of offset diode model can be found in example 9.3, pg 471 and 9.4, pg 473
The offset diode could be depicted as an ideal diode in series with barrier potential V. The voltage at V1 will decide if the diode is OFF or ON
V1 =
R1 .V S R1+ RS
At V S < .V (1 +
At V S .V (1 +
V L = V1 V
KCL at node 1 iS - i1 - iL =0
V1 =
V S / R S + V / R L 1 / R S + 1 / R1 + 1 / R L
9.13 In the circuit of Figure P9.13, find the range of Vin for which D1 is forward-biased. Assume ideal diodes. The diodes are given as ideal. For forward biasing, we can replace D1 with a switch such that At vD 0 (positive) => the switch is closed
Additional: Can you see that voltage across 500 resistor can never exceed 1.5V? (hint: when both diode starts conducting, meaning to say the switches are closed, the 1.5V source is parallel to the 500 resistor.
9.27 In the rectifier circuit shown in Figure P9.26, v(t) = A sin(2 100t) V. Assume a forward voltage drop of 0.7V across the diode when it is conducting. If conduction must begin during each positive half-cycle at an angle no greater than 50, what is the minimum peak value A that the AC source must produce? Note that the diode is NOT an ideal type. Similar to problem 9.8. For the diode to conduct: Condition 1: we are told that it needs minimum 0.7 V (forward voltage drop) Condition 2: we are told that it needs minimum (no greater than) 50 in the positive cycle. From 1 and 2
9.29 A half-wave rectifier, similar to that of Figure 9.25 in the text, is used to provide a DC supply to a 100- load. If the AC source voltage is 30 V (rms), find the peak and average current in the load. Assume an ideal diode. For computing peak and average currents; use the AC relationships:
V peak =
2 .V rms
V avg = V peak /
See example 9.8 pg 486 for another similar example on halfwave rectifier
9.37 In the full-wave power supply shown in Figure P9.37 the diodes are 1N4001 with a rated peak reverse voltage (also called peak inverse voltage) of 50 V. They are fabricated from silicon. VLine = 170 cos(377t) V, n = 0.2941, C = 700 F, RL = 2.5 K Determine the actual peak reverse voltage across each diode. 1. This is a standard bridge rectifier circuit. Note that the diodes are not ideal but they are identical (same IC number); so they would have similar characteristics (voltage- drops/current etc). We also know that at any instant of time (positive or negative cycle), two of them are conducting and two are open. 2. Note, n<1, so you have a step-down transformer. Find VS = n.Vline = ~ 50.cos (377t) V For peak value cos(0)=1 3. Since diodes are identical, consider any pair, lets say D1 and D3.
Write KVL equation for conduction (t = 0) for this pair as shown on R.H.S
V L ( 0 ) + V 1 + V 3 V SO . cos( 0 ) = 0
The peak reverse voltage is the voltage across the diodes when they are reverse biased (open circuit while no current flows). It is reverse polarity - negative.
Similarly, Write KVL equation for non-conduction (t =) for the same pair:
V L ( ) V D 1 ( ) V D 3 ( ) V SO . cos( ) = 0
VL(0)=VL()= 48.6V
VD1 + VD 3 = (50 + 48.6)
Evaluate VD1=VD3=?
Ans: - 49.3 V