You are on page 1of 62

SIEU THANH COMPANY LIMITED

TRAINING DEPARTMENT

SERVICE MANUAL

550/551/650/700/850

COMPANY., LTD

SERVICE PROGRAM MODE

June 30, 1998

4.2.2 SERVICE PROGRAM MODE TABLES


NOTE: 1) In the Function column, comments are in italics. 2) In the Settings column, the default value is in bold letters. 3) An asterisk ( * ) in the right hand side of the mode number column means that this mode is stored in the NVRAM. If you do a RAM reset, all these SP modes will be reset to their factory settings.
Mode No. Function (Class 1 , 2 & 3) 1-001 Leading Edge Registration * Adjusts the printing leading edge registration using the trimming area pattern (SP2-902-3, No.10). Use the key to toggle between + and before entering the value. The specification is 3 2 mm. See "Replacement and Adjustment - Copy Image Adjustments" for details. 1-002 Side-to-Side Registration 1 Tray - 1 * Adjusts the printing side-to-side registration from the 1st paper feed station using the trimming area pattern (SP2-9023, No.10). Use the key to toggle between + and before entering the value. The specification is 0 2.0 mm. See "Replacement and Adjustment - Copy Image Adjustments" for details on SP1002. 2 Tray - 2 * Adjusts the printing side-to-side registration from the 2nd paper feed station using the trimming area pattern (SP2-9023, No.10). Use the key to toggle between + and before entering the value. The specification is 0 2.0 mm. 3 Tray - 3 * Adjusts the printing side-to-side registration from the 3rd paper feed station using the trimming area pattern (SP2-9023, No.10). Use the key to toggle between + and before entering the value. The specification is 0 2.0 mm. 4 Tray - 4 * Japanese version only. 5 Duplex Tray * Adjusts the printing side-to-side registration from the duplex tray using the trimming area pattern (SP2-902-3, No.10). Use the key to toggle between + and before entering the value. The specification is 0 2.0 mm. Settings +9 ~ -9 0.1 mm/step + 3.0 mm

+9 ~ -9 0.1 mm/step + 0.0 mm

+9 ~ -9 0.1 mm/step + 0.0 mm

+9 ~ -9 0.1 mm/step + 0.0 mm

+9 ~ -9 0.1 mm/step + 0.0 mm

550

4-10

June 30, 1998


Mode No. (Class 1 , 2 & 3) 1-002 Side-to-Side Registration 6 By-pass Tray * Function

SERVICE PROGRAM MODE


Settings +9 ~ -9 0.1 mm/step + 0.0 mm

LCT

Adjusts the printing side-to-side registration from the by-pass feed table using the trimming area pattern (SP2-9023, No.10). Use the key to toggle between + and before entering the value. The specification is 0 2.0 mm. Adjusts the printing side-to-side registration from the LCT using the trimming area pattern (SP2-902-3, No.10). Use the key to toggle between + and before entering the value. The specification is 0 2.0 mm.

+9 ~ -9 0.1 mm/step + 0.0 mm

1-003

1-007

Adjusts the relay clutch timing at registration. The relay clutch timing determines the amount of paper buckle at 2 By-pass Tray * registration. (A +ve setting leads to more buckling.) By-pass Feed Paper Size Display Displays the paper width sensor data for the by-pass feed table. 132 : A3 133 : A4 Lengthwise 134 : A5 Lengthwise 141 : B4 Lengthwise 142 : B5 Lengthwise 160 : DLT 164 : LG 166 : LT Lengthwise 172 : HLT Lengthwise * Duplex Fence Adjustment *

Paper Feed Timing 1 Tray, Duplex

+9 ~ -9 1 mm/step + 0 mm
Service Tables

1-008

Adjusts the distance between the front and rear fences.

+4 ~ -4 0.5 mm/step + -1.0 mm 0: 51/2 min. 1: 10 min. 2: 15 min. 3: No idling

1-103

Fusing Idling * Selects whether fusing idling is done or not. If fusing is incomplete on the 1st and 2nd copies, change the setting to a longer time. This may occur if the room is cold. Refer to Detailed Section Descriptions Fusing Temperature Control for more details.

1-104

Fusing Temperature Control * Selects the fusing temperature control mode. After changing the setting, turn the main switch off and on.

On/Off control Phase control

550

4-11

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 1-105 Fusing Temperature Adjustment 1 By-pass * Adjusts the fusing temperature for paper fed from a by-pass tray. 2 OHP * Adjusts the fusing temperature for OHP sheets fed from the by-pass feed unit. Adjusts the fusing temperature for thick paper fed from the by-pass feed unit.

June 30, 1998


Settings 170 ~ 200 1C/step 185C +10 ~ -10C 1C/step 0 (165C) +5 ~ -10C 1C/step 0 (165C)

Thick Paper

1-106

Fusing Temperature Display Displays the fusing temperature.

1-901

CPM Change for Thick Paper 1 Tray 1 * Selects the copy speed when the fusing 2 Tray 2 * temperature goes down when using thick 3 Tray 3 * paper. 4 Tray 4 * 5 LCT * During a long copy run, the hot roller cools down. This may cause poor fusing. To do this, the copy speed can be reduced when the temperature reaches a certain level. The 4th tray is used for the Japanese version only. By-pass Tray Paper Size Correction* Calibrates the minimum paper width 1 Minimum Size position of the sensor (100 mm). Calibrates the maximum paper width 2 Maximum Size position of the sensor (A3). Thick Paper Mode - By-pass Table * Selects the by-pass feed clutch on mode for thick paper mode. Charge Corona Bias Adjustment 1 Image Area * Adjusts the voltage applied to the grid plate during copying when auto process control is off. Normally, there is no need to adjust this. If there is an ID or TD sensor problem, the machine goes into fixed toner supply mode. After replacing the drum or charge corona wire, change this value to the default. 2 ID Sensor Pattern * Adjusts the voltage applied to the grid plate when making the ID sensor pattern. Normally, there is no need to adjust this.. If the user wants high density copies, the sensor pattern must be lighter, so this voltage must be a higher negative voltage.

0: None 1: 50 cpm 165C 2: 45 cpm 175C

1-904

Start Start

1-905

ON: Twice OFF: Once

2-001

-600 ~ -1300 10 V/step -1000 V

-600 ~ -1300 10 V/step -650 V

550

4-12

June 30, 1998

SERVICE PROGRAM MODE


Settings -900 ~ -1500 10 A/step 1200 A -600 ~ -1300 10 V/step -1000 V

Mode No. Function (Class 1 , 2 & 3) 2-001 Charge Corona Bias Adjustment 3 Total Corona * Adjusts the current applied to the charge Current corona wire. Factory use only. 4 Image Area * Adjusts the voltage applied to the grid plate during copying when auto process control is on. This voltage changes every time auto process control starts up (every time the machine is switched on) 5 OHP Sheet * Adjusts the voltage applied to the grid plate when OHP mode is selected. Use this if there is a copy quality problem when making OHPs. Normally there is no need to adjust this. See 2-001-1. 2-101 Printing Erase Margin 1 Leading Edge * Adjusts the leading edge erase margin. The specification is 3 2 mm. See "Replacement and Adjustment - Copy Image Adjustments" for more on SP2-101. 2 Trailing Edge * Adjusts the trailing edge erase margin. The specification is 3 2 mm. 3 Left * Adjusts the left side erase margin. The specification is 2 1.5 mm. Adjusts the right side erase margin. The specification is 2 +2.5/-1.5 mm.

-600 ~ -1300 10 V/step 780 V

Right

0.0 ~ 9.0 0.1 mm/step 2.0 mm 0.0 ~ 9.0 0.1 mm/step 2.0 mm 0.0 ~ 9.0 0.1 mm/step 2.0 mm
-127 ~ +127

2-103

LD Power Adjustment 1 LD1 - 400dpi

Adjusts the power of LD1 for 400 dpi resolution. Do not change the value. Adjusts the power of LD1 for 600 dpi resolution. Do not change the value. Adjusts the power of LD2 for 400 dpi resolution. Do not change the value. Adjusts the power of LD2 for 600 dpi resolution. Do not change the value. Factory use only. Do not use this SP mode. Factory use only. Do not use this SP mode.

1/step 1=1.1 W +0
-127 ~ +127

LD1 - 600dpi

1/step 1=1.1 W +0
-127 ~ +127

LD2 - 400dpi

1/step 1=1.1 W +0
-127 ~ +127

LD2 - 600dpi

LD1 Power Adjustment (Start/End) LD2 Power Adjustment (Start/End)

1/step 1=1.1 W +0 Start Stop Start Stop

550

4-13

Service Tables

0.0 ~ 9.0 0.1 mm/step 2.0 mm

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 2-109 Laser Beam Pitch Adjustment 1 400 dpi * Adjusts the laser beam pitch value for 400 dpi resolution. After replacing the LD unit or replacing or clearing the NVRAM, use this SP mode and SP2-109-3 to adjust the laser beam pitch. Refer to Replacement and Adjustment - Laser Beam Pitch Adjustment for details. 2 600 dpi * Adjusts the laser beam pitch value for 600 dpi resolution. After replacing the LD unit , replacing or clearing the NVRAM, use this SP mode and SP2-109-4 to adjust the laser beam pitch. Refer to Replacement and Adjustment - Laser Beam Pitch Adjustment for details. Initializes the laser beam pitch for 400 dpi to the SP2-109-1 value. After inputting a value for SP2-109-1, this SP must be used. Initializes the laser beam pitch for 600 dpi to the SP2-109-2 value. After inputting a value for SP2-109-2, this SP must be used. Inputs the interval for the automatic laser beam pitch adjustment When the number of times that the resolution been changed reaches this value, the laser unit position is automatically corrected. Displays the current LD unit position (number of pulses from home position). If this is different from the value of 2-109-1 or 2-109-2, LD unit positioning has failed. Displays how many times the LD unit position has been changed (how many times the resolution has changed.) When the laser beam pitch adjustment is done, this counter is reset to 0. Resets the values of SP2-109-6 and SP2109-7. After replacing the LD unit, this SP mode must be done.

June 30, 1998


Settings 0 ~ 262 4 pulses/step 144

0 ~ 284 4 pulses/step 168

400 dpi Initial Setting

Start

600 dpi Initial Setting

Start

Auto Pitch Adjustment Interval

0 ~ 65535 1/step 1000 times

Current LD Unit Position

Beam Pitch Change Counter

Beam Pitch Data Reset

2-110

Test Mode dpi Designer use only. Do not change this value. 0: 400 dpi 1: 600 dpi 2: 15.4 x 16 3: 16 x 15.4

550

4-14

June 30, 1998

SERVICE PROGRAM MODE


Settings -200 ~ -700 10 V/step -550 V

Mode No. Function (Class 1 , 2 & 3) 2-201 Development Bias Adjustment 1 Image Area * Adjusts the development bias for copying. This can be adjusted as a temporary measure if faint copies appear due to an aging drum. Adjusts the development bias for making the ID sensor pattern for Vsp measurement. This should not be used in the field, because it affects ID sensor pattern density, which affects toner supply. Adjusts the development bias for copying onto OHP sheets.

ID Sensor Pattern

-200 ~ -700 10 V/step -440 V

OHP Sheet

-200 ~ -700 10 V/step -550 V -140 ~ -380 1 V/step -320 V

Development Performance

2-207

Forced Toner Supply Forces the toner bottle to supply toner to the toner supply unit for 7 seconds. This mode finishes automatically after the toner is supplied 7 times (1 s for each time). This process is not normally needed in the field for this model. Start

2-208

Toner Supply Mode * Selects the toner supply mode. Use image pixel count mode only as a temporary countermeasure if the ID or TD sensor is defective. Sensor Control Image Pixel Count

2-209

Toner Supply Rate * Adjusts the toner supply rate. Increasing this value reduces the toner supply clutch on time. Use a lower value if the user tends to make lots of copies that have a high proportion of black. 50 ~ 2000 5 mg/s/ step 850 mg/s

2-210

ID Sensor Interval Changes the interval for making the ID sensor pattern (VSP/VSG detection). If the user normally makes copies with a high proportion of black, reduce the interval. 0 ~ 500 1 copy/step 50 copies

550

4-15

Service Tables

Adjusts the development potential for making the ID sensor pattern for Vsp measurement. Do not adjust.

SERVICE PROGRAM MODE


Mode No. (Class 1 , 2 & 3) 2-220 VREF Manual Setting * Function Adjusts the TD sensor reference voltage (VREF). Change this value after replacing the development unit with another one that already contains toner. For example, when using a development unit from another machine for test purposes, do the following: 1. Check the value of SP2-220 in both the machine containing the test unit and the machine that you are going to move it to. 2. Install the test development unit, then input the VREF for this unit into SP2-220. 3. After the test, put back the old development unit, and change SP2-220 back to the original value. 2-223 VT Display * Displays the current TD sensor output voltage.

June 30, 1998


Settings 1.60 ~ 3.50 0.01V/step 2.5 V

2-301

Transfer Current Adjustment 1 1st copy * Adjusts the current applied to the transfer belt during copying on the 1st side of the paper. If the user uses thicker paper, the current may have to be increased to ensure sufficient transfer of toner. 2 2nd Copy * Adjusts the current applied to the transfer belt during copying on the 2nd side of the paper. See above. Adjusts the current applied to the transfer belt during copying from the by-pass feed table. See above. If the user normally feeds thicker paper from the bypass tray, use a higher setting. Adjusts the current applied to the transfer belt during copying on post cards from the by-pass feed table. The post card mode is selected when the by-pass tray is selected and the width is detected as A6. Adjusts the current applied to the transfer belt between the pages.

15 ~ 200 1 A/step 60 A

15 ~ 200 1 A/step 60 A

By-pass Tray

15 ~ 200 1 A/step 70 A

Post Card

15 ~ 200 1 A/step 150 A

Between Papers

15 ~ 200 1 A/step 15 A

550

4-16

June 30, 1998

SERVICE PROGRAM MODE


Settings 1 : No 2 : Yes

Mode No. Function (Class 1 , 2 & 3) 2-506 Cleaning Interval Multiple Copy 1 Operation * Selects whether multiple copy jobs are stopped at regular intervals for the following purposes. 1. Stop and turn the drum motor in reverse to clean the cleaning blade edge 2. Make an ID sensor pattern to correct the toner density control. The interval depends on SP2-506-2. Use if the drum gets dirty or images get too pale or too dark during a long job. 2 Interval * Selects the interval at which multi copy jobs are stopped. 2-801 TD Sensor Initial Setting * Performs the TD sensor initial setting. This SP mode controls the voltage applied to the TD sensor to make the TD sensor output about 2.5 V. After finishing this, the TD sensor output voltage is displayed. Use this mode only after changing the TD sensor or the developer. 2-803 Corona Wire Cleaner On Turns on the corona wire cleaner manually. When copy density across the paper is uneven at EM, clean the wire with this mode. Corona Wire Cleaner Operation Setting 1 On/Off Selects whether corona wire cleaner operation is done. When Operate is selected, the period is set with SP2-804-2. 2 Operation * Selects the operation interval of the corona Interval wire cleaner. Printing Test Pattern 2 IPU Test Pattern

1 ~ 100 1 minute/step 15 minutes Start

Start

2-804

1:Operate (yes) 0:Not operate (No) 100 ~ 10 k 100 print/step 5k

2-902

Printing Test Pattern

Prints the test patterns for the IPU chip. See section 4.2.3. for how to print test patterns. This SP mode is useful for finding whether the SBICU or the SBU is defective. If the printout is not OK, the SBICU is defective. Prints the printer test patterns. See section 4.2.3. for how to print test patterns. Example: 10. Trimming Area This SP mode is useful for finding whether the LDDR or the SBICU is defective. If the printout is not OK, the LDDR is defective. * Factory use only. 10 V

2-906

Vcont Manual Setting

550

4-17

Service Tables

SERVICE PROGRAM MODE


Mode No. (Class 1 , 2 & 3) 2-909 Main Scan Magnification 1 Copier * Function Adjusts the magnification in the main scan direction for copy mode. Use the key to toggle between + and -. See "Replacement and Adjustment Copy Image Adjustments" for details. 2 Printer * Adjusts the magnification in the main scan direction when printing from a personal computer. Use the key to toggle between + and -. See "Replacement and Adjustment - Copy Image Adjustments" for details. 2-911 Transfer Current On/Off Timing 1 La(ON) * Adjusts the transfer current on timing at the leading edge. 3 Lc(OFF) * Adjusts the transfer current off timing (for example: 5 mm is 5 mm after the trailing edge).

June 30, 1998


Settings - 2.0 ~+ 2.0 0.1 %/step + 0.0 %

- 2.0 ~+ 2.0 0.1 %/step + 0.0 %

-30 ~ +30 1 mm/step 0 mm -30 ~ +30 1 mm/step 0 mm

2-912

Drum Reverse Rotation Interval * This SP mode is for designer use only. Do not change the value.. Test Pattern ID Adjustment Adjusts the image density for printing test patterns (with SP2-902). Usually this SP mode is only used by designers. The value is cleared when the main power switch is turned off and on.

0 ~ 300 20 ms/step 40 ms 0 ~ 15 1/step 15

2-913

2-920

LD Off Check Checks whether the LD turns off or on when the front door is opened. 0 : On 1: Off Factory use only. Transfer Belt Cleaning DPI Change * When resolution changes from 400 to 600 dpi, the LD writes a pattern on the drum. Toner is applied, and this must be cleaned off the belt. This SP mode determines whether bias is applied to the transfer belt cleaning bias roller at this time. Developer Initialization (Factory) Factory use only.

2-930

0 : No 1 : Yes

2-961

550

4-18

June 30, 1998


Mode No. (Class 1 , 2 & 3) 2-962 Auto Process Control * Function

SERVICE PROGRAM MODE


Settings Start

Automatically adjusts the following process control factors. 1. ID sensor 2. Drum potential sensor 3. Charge grid voltage (by changing VD) 4. LD power (by changing VH) Before using this SP, auto process control should be on (SP3-901) After changing the drum, ID sensor, drum potential sensor, LD unit, or toner density sensor, this SP should be used.

2-963

Do not use this SP after replacing the developer. Use SP2-801 (developer initialization) 2-964 Blade Protection 1 Pattern Interval * Selects the interval for applying a strip of toner across drum and transfer belt to prevent the drum cleaning blade and belt cleaning blade from peeling off. Selects the LD power for making the toner strip on the drum and transfer belt to prevent the drum cleaning blade and belt cleaning blade from peeling off. 0 ~ 50 1 /step 0 (not applied) 0 ~ 15 1 /step 1

Pattern Density

2-965

Toner Pump Adjustment * 1 First Toner Waste Adjustment 2 After First Toner Waste Pump Clutch On Time Pump Motor On Time Return to First Toner Waste *

Factory use only

0 ~ 100 1g /step 3g 0 ~ 100 1 g /step 3g 0~5 1 /step 2s 0 ~ 20 1 s/step 6s 0 ~ 50 1 time/step 30 times

Factory use only

Factory use only

Factory use only

Factory use only

550

4-19

Service Tables

Toner Supply From Toner Bottle When installing a new machine, the following two process are done automatically. 1. Developer initialization 2. Forced toner supply (sends toner to the toner hopper)

Start

SERVICE PROGRAM MODE


Mode No. (Class 1 , 2 & 3) 2-967 Auto Image Density Adjustment Function

June 30, 1998


Settings * On

3-001

ID Sensor PWM Setting 1 ID Sensor * PWM Setting

This SP mode is added to recover the machine when an SC condition occurs because ID Sensor Initial Setting is not done after doing an NVRAM Clear or replacing the NVRAM. Reset this SP to the factory setting in this case. The PWM data is stored when ID Sensor Initial Setting is done. Performs the ID sensor initial setting. The ID sensor output for the bare drum (VSG) is adjusted to 4.0 0.2V. This SP mode should be performed after: 1. Replacing or cleaning the ID sensor 2. Replacing the NVRAM or doing an NVRAM clear 3. Replacing the SBICU board Displays the current VSG and VSP output. VSP= x.xx V VSG= x.xx V If the ID sensor does not detect the ID pattern, "VSP=5.0V/VSG=5.0V" is displayed and an SC code is generated. If the ID sensor does not detect the bare area of the drum, "VSP=0.0V/VSG=0.0V" is displayed and an SC code is generated.

0 ~ 255 1/step 90

Initialization

Start

3-103

ID Sensor Output Display *

3-901

Auto Process Control Decides whether or not the machine checks and corrects the drum potential (VD) and LD power when the fusing temperature is lower than 100C at powerup. Process Control Data Display 1 Auto Process * Displays whether auto process control is Control on or off.
(O: OFF, 1: ON)

ON OFF

3-902

2 3 4 5

VD Half Tone VH VG LD Power (Correction) VID

* * * *

Displays the drum potential. Displays the drum potential in areas illuminated by the laser. Displays the charge grid voltage which resulted from the latest VD adjustment. Displays the LD power correction value which resulted from the latest VH adjustment. Displays the latest drum surface voltage measured on the ID sensor pattern.

550

4-20

June 30, 1998

SERVICE PROGRAM MODE

Mode No. Function (Class 1 , 2 & 3) 4-008 Scanner Sub Scan Magnification * Adjusts the magnification in the sub scan direction for scanning. If this value is changed, the scanner motor speed is changed. Use the key to toggle between + and -. See "Replacement and Adjustment - Copy Image Adjustments" for details. 4-010 Scanner Leading Edge Registration * Adjusts the leading edge registration for scanning. (-): The image moves in the direction of the leading edge Use the key to toggle between + and -. See "Replacement and Adjustment - Copy Image Adjustments" for details. Scanner Side-to Side Registration * Adjusts the side-to-side registration for scanning. (-): The image disappears at the left side. (+): The image appears at the left side. Use the key to toggle between + and -. See "Replacement and Adjustment - Copy Image Adjustments" for details. Scanner Erase Margin 1 Leading Edge * Adjusts the leading edge erase margin for scanning. Do not adjust this unless the user wishes to have a scanner margin that is greater than the printer margin. 2 Trailing Edge * Adjusts the trailing edge erase margin for scanning. See the comment for SP 4-012-1. * Adjusts the left side erase margin for scanning. See the comment for SP 4-012-1. * Adjusts the right side erase margin for scanning. See the comment for SP 4-012-1. 4-013 Scanner Free Run Performs a scanner free run with the exposure lamp on.

Settings - 0.9 ~ + 0.9 0.1 %/step + 0.0 %

- 9.0 ~ + 9.0 0.1 mm/step + 0.0 mm

4-011

- 6.0 ~ + 6.0 0.1 mm/step + 0.0 mm

4-012

0.0 ~ 0.9 0.1 mm/step 0.5 mm

0.0 ~ 0.9 0.1 mm/step 0.5 mm 0.0 ~ 0.9 0.1 mm/step 0.5 mm 0.0 ~ 0.9 0.1 mm/step 0.5 mm

Left

Right

0: Stop 1: Start

550

4-21

Service Tables

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 4-301 APS Sensor Output Display Displays the APS sensor output signals when an original is placed on the exposure glass. Bit 0: Width sensor 1 Bit 1: Width sensor 2 Bit 2: Width sensor 3 Bit 3: Length sensor 1 Bit 4: Length sensor 2 See Detailed Section Descriptions Original Size Detection in Platen Mode for more details. 4-303 APS A5/HLT Size Original Detection * Selects whether or not the copier determines that the original is A5/HLT size when the APS sensor does not detect the size. If "A5 length/51/2" x 81/2" is selected, paper sizes that cannot be detected by the APS sensors are regarded as A5 lengthwise or 51/2" x 81/2". If "Not detected" is selected, "Cannot detect original size" will be displayed. Scanner Adjustment 1 Flag Display 2 Standard

June 30, 1998


Settings 00000000 0: Not detected 1: Detected

0: Not detected 1: A5 length / 51/2" x 81/2"

4-428

* Displays whether or not the standard white level adjustment has been done. Corrects the standard white level from the white plate. This SP mode is for factory use only. Do not use this SP mode. * Checks the difference value of the black level for the EVEN channel after adjusting the black level at power-up. This SP mode is for designer use only. Do not use this SP mode. * Checks the difference value of the black level for the ODD channel after adjusting the black level at power-up. This SP mode is for designer use only. Do not use this SP mode. * Checks the value of the black level for the EVEN channel after adjusting the black level at power-up. This SP mode is for designer use only. Do not use this SP mode. * Checks the value of the black level for the ODD channel after adjusting the black level at power-up. This SP mode is for designer use only. Do not use this SP mode.

Adjusted Not adjusted Start

4-901

SBU Adjustment E/O 1 Adjustment E ch

0 ~255 1/step 147

E/O Adjustment O ch

0 ~255 1/step 127

Bk Adjustment - E ch

0 ~ 255 1/step 127

Bk Adjustment - O ch

0 ~ 255 1/step 145

550

4-22

June 30, 1998


Mode No. (Class 1 , 2 & 3) 4-901 SBU Adjustment 5 Digital Gain Adjustment E ch Function

SERVICE PROGRAM MODE


Settings 0~1 1/step 0

Digital Gain Adjustment O ch

Analog Gain Adjustment E ch

Analog Gain Adjustment O ch

Standard White Level Adjustment

* Checks the AGC gain value of the white level for the EVEN channel after adjusting the white level at power-up. This SP mode is for designer use only. Do not use this SP mode. * Checks the AGC gain value of the white level for the ODD channel after adjusting the white level at power-up. This SP mode is for designer use only. Do not use this SP mode. * Checks the AGC gain value of the white level for the EVEN channel after adjusting the white level at power-up. This SP mode is for designer use only. Do not use this SP mode. * Checks the AGC gain value of the white level for the ODD channel after adjusting the white level at power-up. This SP mode is for designer use only. Do not use this SP mode. * Checks the value of the standard white level after adjusting the white level. This SP mode is for factory use only. Do not use this SP mode. * Adjusts the upper limit voltage for A/D conversion in ADS mode. This SP mode is for designer use only. Do not use this SP mode. This SP mode is for designer use only. Do not change the value. * Checks the AGC gain value of the white level for the EVEN channel after adjusting the white level in the factory. This SP mode is for factory use only. Do not use this SP mode. * Checks the AGC gain value of the white level for the ODD channel after adjusting the white level in the factory. This SP mode is for factory use only. Do not use this SP mode. * Checks the value of the standard white level in the factory. This SP mode is for factory use only. Do not use this SP mode. Checks the overflow flag data during the automatic scanner adjustment. This SP mode is for designer use only.

0~1 1/step 0

0 ~ 255 1/step 46

0 ~ 255 1/step 46
Service Tables

0 ~ 255 1/step 110

10

A/D Standard Voltage in AE Mode

0 ~ 255 1/step 191

11 12

Image Data Path Setting Gain Adjustment - E ch

0
INIT_GAIN(E)

= b7;023

13

Gain Adjustment O ch

INIT_GAINO = b7;023

14

Standard White Level Adjustment at Factory Overflow Flag

INIT_REF = 110

15

OFO/SGDO = 0000 OFE/SGDO = 0000

550

4-23

SERVICE PROGRAM MODE


Mode No. (Class 1 , 2 & 3) 4-901 SBU Adjustment 16 Time Out Flag Function Checks the time out flag data during the automatic scanner adjustment. This SP mode is for designer use only. Checks the error flag data during the automatic scanner adjustment. This SP mode is for designer use only. Checks either the maximum or minimum white shading data. This SP mode is for designer use only. * This SP mode is designer use only. Do not change the value. Selects whether the copy is always in full size mode even if the magnification ratio has been changed. Set to 1 when checking the magnification in the main scan direction. If the magnification is not 100%, something is wrong with the image processing circuits. Adjusts the pixel shift amount in the main scan direction in magnification mode. This SP mode is for designer use only. Selects the MTF filter coefficient in the main scan direction for 25% ~ 64% reduction for text mode. 0:Weak 6:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. Selects the MTF filter coefficient in the main scan direction for 65% ~ 154% magnification for text mode. 0:Weak 6:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. Selects the MTF filter coefficient in the main scan direction for 155% ~ 256% enlargement for text mode. 0:Weak 6:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. Selects the MTF filter coefficient in the main scan direction for 257% ~ 400% enlargement for text mode. 0:Weak 6:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode.

June 30, 1998


Settings TIME OUT/SGDO = 0000 GAIN/OET = 000 REF/OT=00 0: Maximum 1: Minimum

17

Error Flag

18

White Level Data

4-903

Filter Setting 2 Filter Mode Setting Full Size 5 Mode

0~3 0 0: Normal operation 1: Always full size mode

11

Image Shift in Magnification Mode Filter Level (25% ~ 64%)

0 ~ 5120 1/step 0 0~6 1/step 1

12

Filter Level (65% ~ 154%)

0~6 1/step 2

13

Filter Level
(155% ~ 256%)

0~6 1/step 5

14

Filter Level
(257% ~ 400%)

0~6 1/step 6

550

4-24

June 30, 1998


Mode No. (Class 1 , 2 & 3) 4-903 Filter Setting 15 MTF Filter in Photo Mode Function

SERVICE PROGRAM MODE


Settings 0~4 1/step 2

16

Smoothing Filter in Photo mode

17

Filter Level Text/Photo Mode

18

Filter Level in Pale Mode

* Selects the MTF filter coefficient for photo mode, if MTF is enabled for this mode with SP 4-904-3. 0:Weak 4:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the smoothing filter coefficient for photo mode. 0:Weak 7:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. Selects the MTF filter coefficient for text areas in text/photo mode. 0:Use the filter coefficient and strength level for letter mode. 1:Weak 5:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the table of the MTF filter coefficient for pale original mode 0:Use the filter coefficient level for text mode. 1:Weak 5:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF filter coefficient for generation copy mode 0:Use the filter coefficient level for text mode. 1:Weak 5:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF strength in the main scan direction for 25% ~ 64% reduction for text mode. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF strength in the main scan direction for 65% ~ 154% magnification for text mode. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF strength in the main scan direction for 155% ~ 256% enlargement for text mode. This SP is ignored unless the user selects SP Mode Changed in UP mode.

0~7 1/step 1

0~5 1/step 0

0~5 1/step 0

19

Level in Generation Copy

0~5 1/step 3

20

Filter Strength (25% ~ 64%)

0: x 0.25 1: x 0.5 2: x 1 3: x 2 4: x 4 0: x 0.25 1: x 0.5 2: x 1 3: x 2 4: x 4 0: x 0.25 1: x 0.5 2: x 1 3: x 2 4: x 4

21

Filter Strength (65% ~ 154%)

22

Filter Strength
(155% ~ 256%)

550

4-25

Service Tables

SERVICE PROGRAM MODE


Mode No. (Class 1 , 2 & 3) 4-903 Filter Setting 23 Filter Strength
(257% ~ 400%)

June 30, 1998


Function * Selects the MTF strength in the main scan direction for 257% ~ 400% enlargement for text mode. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the independent dot erase level for text mode. Refer to Detailed Section Description Independent Dot Erase for details. * Selects the independent dot erase level for text/photo mode. Refer to Detailed Sectional Description Independent Dot Erase for details. * Selects the independent dot erase level for pale mode. Refer to Detailed Section Description Independent Dot Erase for details. * Selects the independent dot erase level for generation copy mode. Refer to Detailed Sectional Description Independent Dot Erase for details. * Adjust the threshold level for the background erase function in letter mode. A larger value reduces dirty background. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Adjust the threshold level for the background erase function in text/photo mode. A larger value reduces dirty background. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Adjust the threshold level for background erase in generation copy mode. A larger value reduces dirty background. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF filter coefficient in the sub scan direction for 25% ~ 64% reduction for text mode. 0:No filter, 1:Weak 8:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF filter coefficient in the sub scan direction for 65% ~ 154% magnification for text mode. 0:No filter, 1:Weak 8:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. Settings 0: x 0.25 1: x 0.5 2: x 1 3: x 2 4: x 4 0 ~ 15 1/step 2 0 ~ 15 1/step 9 0 ~ 15 1/step 1 0 ~ 15 1/step 1 0 ~ 255 1/step 15

28

Independent Dot Erase Text Mode Independent Dot Erase Text/Photo Mode Independent Dot Erase Pale Mode Independent Dot Erase Generation Copy Mode Scanner Gamma Thresh Level Text

30

31

32

33

34

Scanner Gamma Thresh Level Text/Photo

0 ~ 255 1/step 15

35

Scanner Gamma Thresh Level Generation Copy MTF Filter Level (25% ~ 64%)

0 ~ 255 1/step 15

41

0~8 1/step 3

42

MTF Filter Level (65% ~ 154%)

0~8 1/step 4

550

4-26

June 30, 1998


Mode No. (Class 1 , 2 & 3) 4-903 Filter Setting 43 MTF Filter Level
(155% ~ 256%)

SERVICE PROGRAM MODE


Function * Selects the MTF filter coefficient in the sub scan direction for 155% ~ 256% enlargement for text mode. 0:No filter 1:Weak 8:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF filter coefficient in the sub scan direction for 257% ~ 400% enlargement for text mode. 0:No filter, 1:Weak 8:Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF or smoothing filter coefficient for photo areas in text/photo mode. 0:MTF Filter Weak 1:MTF Filter Medium 2:MTF Filter Strong 3:No filter 4:Smoothing Filter Weak 5:Smoothing Filter Medium 4:Smoothing Filter Strong This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF strength in the sub scan direction for 25% ~ 64% reduction in text mode. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF strength in the sub scan direction for 65% ~ 154% magnification in text mode. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF strength in the sub scan direction for 155% ~ 256% enlargement in text mode. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the MTF strength in the sub scan direction for 257% ~ 400% enlargement in text mode. This SP is ignored unless the user selects SP Mode Changed in UP mode. Settings 0 ~ 11 1/step 3

44

MTF Filter Level


(257% ~ 400%)

0~8 1/step 8

47

50

MTF Filter Strength (25% ~ 64%)

0: x 0.25 1: x 0.5 2: x 1 3: x 2 4: x4 0: x 0.25 1: x 0.5 2: x 1 3: x 2 4: x 4 0: x 0.25 1: x 0.5 2: x 1 3: x 2 4: x 4 0: x 0.25 1: x 0.5 2: x 1 3: x 2 4: x 4

51

MTF Filter Strength (65% ~ 154%)

52

MTF Filter Strength


(155% ~ 256%)

53

MTF Filter Strength


(257% ~ 400%)

550

4-27

Service Tables

Filter Type in Photo Area (Text/Photo mode)

0~6 1/step 2

SERVICE PROGRAM MODE


Mode No. (Class 1 , 2 & 3) 4-904 IPU Setting -1 1 Laser Pulse Positioning in Text and Text/Photo Dither Matrix 2 Selection Function * Selects whether or not laser pulse positioning control is used in text and text/photo modes Do not change the value. * Selects the dither matrix for photo mode when SP4-904-24 is 2. If 0 is selected, the image will be sharper. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the filter type for photo mode. Coefficients used: 0: SP4-903-15, 1: SP4-903-16 If 0 is selected, the image will be sharper. However, dot screen areas will be faint. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the line width correction type for generation copy mode. In copied original mode, lines may bulge in the main scan direction. Adjust this SP mode until the result is satisfactory.

June 30, 1998


Settings 0: Off 1: On

0: 4 x 4 1: 6 x 6

Filter Type Selection Photo Mode

0: MTF 1: Smoothing

Generation Mode

0: Not corrected 1: Thin line-1 2: Thin line2 3: Thick line

Gradation Process in Text Area

Gradation Process in Photo Area

Image Data Path

This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the process used for text areas in text/photo mode. 0: 1-dot grayscale 1: 1-dot 9 level error diffusion If 1 is selected, the image becomes sharper in focus. However, gradation will be reduced. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the process used for photo areas in text/photo mode. 0: 1-dot grayscale 1: 1-dot 9 level error diffusion 2: 2-dot grayscale 3: 2-dot 17 level error diffusion As the setting increases from 1 to 3, the image becomes sharper in focus. However, gradation will be reduced. This SP is ignored unless the user selects SP Mode Changed in UP mode. Selects one of the following video data outputs, which will be used for printing. 0: After image scanning 1: After image data form application 2: After gradation processing 3: Test pattern 4: Normal video processing Do not change the value.

550

4-28

June 30, 1998


Mode No. (Class 1 , 2 & 3) 4-904 IPU Setting -1 12 Binary Thresh Level 18 Binary Dither Pattern (Number of lines) Binary Error Diffusion Pattern Grayscale Process Photo Mode Function * Not used in this machine

SERVICE PROGRAM MODE


Settings 0 ~ 255 1/step 128 0: 70 (8x8) 1: 95 (6x6) 2: 140 (8x8) 3: 180 (8x8) 0: Matrix 1 1: Matrix 2

* Not used in this machine

23

* Not used in this machine.

24

Do not change the value. * Select the processing type in photo mode. 0: 2-dot/1-dot error diffusion (text/photo separation) 1: 2-dot error diffusion 2: Dither processing This SP is ignored unless the user selects SP Mode Changed in UP mode.
Service Tables

4-905

4-906

Selects one of the following video data outputs, which will be used for printing. 0: Filtering Magnification 1: Magnification Filtering 2: Filtering only 3: Magnification only 4: No processing 5: Normal operation Do not change the value. Selects one of the following video data outputs, which will be 2 Image Data used for gradation processing. Path Gradation 0: After image scanning 1: After MSU 2. No printer gamma 3: Normal operation Do not change the value. 4 Printout Type Selects one of the following video data outputs, which will be Selection used for the printer controller. 0: Normal operation 1: Not printed out 2: Black/white conversion Do not change the value. Image Processing Priority in Text/Photo Mode * Selects either text priority or photo priority 0: Photo for text/photo mode. priority Photo priority: Background erase is off 1: Letter Letter priority: Background erase is on. priority This SP is ignored unless the user selects SP Mode Changed in UP mode. Text/Photo Auto Separation Method * Selects whether auto text/photo separation is done before error diffusion in text/photo mode. This SP is ignored unless the user selects SP Mode Changed in UP mode.

Image Data Path 1 Image Data Path Filtering/Magni fication

4-907

0: No 1: Yes

550

4-29

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 4-908 Text/Photo Separation Method * Select the text/photo separation processing type during the auto text/photo separation stage. This SP is ignored unless the user selects SP Mode Changed in UP mode. 4-909 IPU Setting - 2 Laser Pulse 1 Position Threshold 2 Thin Line Level 1 White Thin Line Level 1 - Black

June 30, 1998


Settings 0: Letter and photo filters 1: Text filter only 2: Photo filter only 0 ~255 1/step 32 0 ~ 15 1 /step 3 0 ~ 15 1 /step 13 0 ~ 15 1 /step 4 0 ~ 15 1 /step 12

Thin Line Level 2 White Thin Line Level 2 - Black

* Decides the threshold level for selecting the type of laser pulse width modulation that is used Do not change the value. * Decides the threshold value for a pixel to be white when line width correction type 1 is performed. Do not change the value. * Decides the threshold value for a pixel to be black when line width correction type 1 is performed. Do not change the value. * Decides the threshold value for a pixel to be white when line width correction type 2 is performed. Do not change the value. * Decides the threshold value for a pixel to be black when line width correction type 2 is performed. Do not change the value. * Selects the gamma table for error diffusion.

Error Diffusion Table

0: Gamma table 0 1: Gamma table 1 0 ~ 255 1 /step 128 0 ~ 255 1 /step 128

Edge Detection 1

Do not change the value. * Decides the threshold value for detecting an edge. Do not change the value. * Decides the threshold value for detecting an edge.

Edge Detection 2

19

Image Data Path Application

Do not change the value. Selects one of the following video data outputs, which will be used for application. 0: After image scanning 1: After image processing 2: After MSU 3: Normal operation

Do not change the value.

550

4-30

June 30, 1998


Mode No. (Class 1 , 2 & 3) 4-909 IPU Setting - 2 20 Image Data Path - Printing Function

SERVICE PROGRAM MODE


Settings

Selects one of the following video data outputs, which will be used for printing. 0: After image processing 1: After MSU 2: From application 3: Normal operation Do not change the value. Designer use only Do not change the value. Designer use only Do not change the value. Designer use only Do not change the value. Checks for bad sectors on the hard disk that develop during machine use. This takes 4 minutes. This SP mode should be done when an abnormal image is printed. There is no need to do this at installation as the hard disk firmware already contains bad sector information, and damage is not likely during transportation. Bad sectors detected with this SP mode will be stored in the NVRAM with the bad sector data copied across from the firmware. If the machine detects over 50 bad sectors, SC361 will be generated. At this time, use SP4-911-2. Formats the hard disk. This takes 4 minutes. Do not turn off the main power switch during this process. Resets the bad sector information which is stored in the NVRAM. This SP should be used when the hard disk is replaced. * Displays the number of bad sectors there are on the hard disk. If the machine detects a total of over 50 bad sectors on the disk, SC361 will be generated. At this time, use SP4-911-2. Displays the model name of the HDD. If the HDD is not installed or the HDD connector is not connected, SC360 will be displayed. However, the user can make single copies. Start
Service Tables

4-910

Data Compression Data 1 Compression 2 Data Compression Threshold ABS Core

0: ON 1: OFF 0 ~ 255 1/step 8 0: ON 1: OFF

4-911

HDD 1 HDD Media Check

HDD Formatting

HDD Bad Sector Information Reset HDD Bad Sector Display

Start

Total: 0 Copy: 0 Printer: 0 Copy Server: 0

HDD Model Name Display

550

4-31

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 4-912 Text/Photo Separation Setting 1 MTF Filter * Selects the strength of the MTF filter (sub (Sub Scan) scan) for edge detection in text/photo Edge separation processing. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the strength of the MTF filter (main scan) for edge detection in text/photo separation processing. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the threshold level for white for edge detection in letter/photo separation processing. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the threshold level for gray for edge detection in letter/photo separation processing. This SP is ignored unless the user selects SP Mode Changed in UP mode. * Selects the threshold level for black for edge detection in letter/photo separation processing. This SP is ignored unless the user selects SP Mode Changed in UP mode. * This SP mode is for designer use only.

June 30, 1998


Settings 0~7 1/step 0

MTF Filter (Main Scan) Edge

0~7 1/step 0

White Threshold Level Edge Detection Gray Threshold Level Edge Detection Black Threshold Level Edge Detection Peak Thresh Level Change Bottom Thresh Level Change H. Max. Thresh Level (Sub Scan) Half Tone L. Max. Thresh Level (Sub Scan) Half Tone H. Min. Thresh Level (Sub Scan) Half Tone L. Min. Thresh Level (Sub Scan) Half Tone H. Max. Thresh Level (Main Scan) Half Tone

0 ~ 255 1/step 16

0 ~ 255 1/step 32

0 ~ 255 1/step 120

* This SP mode is for designer use only.

* This SP mode is for designer use only.

0 ~ 255 1/step 80 0 ~ 255 1/step 155 0 ~ 255 1/step 16 0 ~ 255 1/step 30 0 ~ 255 1/step 40 0 ~ 255 1/step 20 0 ~ 255 1/step 16

* This SP mode is for designer use only.

10

* This SP mode is for designer use only.

11

* This SP mode is for designer use only.

12

* This SP mode is for designer use only.

550

4-32

June 30, 1998

SERVICE PROGRAM MODE


Settings 0 ~ 255 1/step 30 0 ~ 255 1/step 40 0 ~ 255 1/step 20 0 ~ 15 1/step 2 0~5 1/step 3
Service Tables

Mode No. Function (Class 1 , 2 & 3) 4-912 Text/Photo Separation Setting * This SP mode is for designer use only. 13 L. Max. Thresh Level (Main Scan) Half Tone 14 H. Min. Thresh * This SP mode is for designer use only. Level (Main Scan) Half Tone L. Min. Thresh * This SP mode is for designer use only. 15 Level (Main Scan) Half Tone 5x3 Block * This SP mode is for designer use only. 16 Thresh Level Half Tone * Selects the dot screen detection level. 17 Half Tone Separation 0. Setting of SP4-921-008 ~015 Level 1. Letter priority strong 2. Letter priority weak 3. Standard 4. Photo priority weak 5. Photo priority strong Do not use 0; this is for factory use only. 18 Effective * Selects the maximum magnification that can Magnification be used with dot screen detection. Ratio 5-009 Language Selection * Selects the operation panel language. A language card is required except for English, German and Italian. After changing the setting for this SP mode, turn the main power switch off and on. 5-019 Tray Paper Size Selection 5 LCT * Selects the paper size in the optional LCT.

100 ~ 400 1/step 109

A4 LT B5 0: mm 1: inch

5-024

mm/inch Display Selection * Selects what unit is used. After selecting the unit, turn the main power switch off and on.

5-104

A3/DLT Double Count * Specifies whether the counter is doubled for A3/11"x17" paper. If "1" is selected, the total counter and the current user code counter count up twice when A3/11"x17" paper is used. NO YES

5-106

ID Shift Level ADS Level 6 Selection

* Selects the image density level that is used in ADS mode.

1~7 1 notch /step 4

550

4-33

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 5-112 Non-standard Paper Selection * Selects whether a non-standard paper size can be input for tray 2 (universal tray) or not. If 1 is selected, the customer will be able to input a non-standard paper size using a UP mode. 5-113 Optional Counter Type * This SP is for Japan only. Do not change the value. 5-118 Disable Copying * Selects whether the copy function is disabled or not when printer controller is installed. M/C Option Counter Removal * This SP is for Japan only. Do not change the value. Counter Up Timing * Determines whether the optional key counter counts up at paper feed-in or at paper exit. The total counter is not affected by this SP mode. 5-127 APS Mode * Selects whether the APS function is enabled or not. Paper Size Type Selection * Selects the paper size type (for originals and copy paper). (Only needs to be adjusted if the optional printer controller is installed) After changing the value, turn the main power switch off and on. If the paper size type of the archive files stored in the HDD is different, abnormal copies will be made. So, after changing this setting, perform SP5-822 and ask the user to restore the archive files. PM Alarm Interval * Sets the PM interval, with an alarm.

June 30, 1998


Settings NO YES

0~5 1/step 0 0: No 1: Yes

5-120

0~2 1/step 0 0: Feed-in 1: Exit

5-121

NO YES 0: Japan 1: North America 2: Europe

5-131

5-501

0 ~ 255 1k copies/step 0 k copies

5-504

When set to "0", the alarm is disabled. Jam Alarm Level(RSS function) 1 Jam Alarm * Japanese version only. Do not change the values. Level

0: No 1: L 2: M 3: H

550

4-34

June 30, 1998


Mode No. Function (Class 1 , 2 & 3) 5-504 Jam Alarm Level(RSS function) 2 Jam Auto Call * Japanese version only. Do not change the values. (RSS function) 5-505 Error Alarm Level * Japanese version only. Do not change the values. 5-507 Paper Supply Call Level 128 Others * 132 A3 * 133 A4 * 134 A5 * 141 B4 * 142 B5 * 160 DLT * 164 LG * 166 LT * 172 HLT * Auto Call Setting 1 Original Count * 2 Door Open * 3 Paper Supply * 4 Stapler Supply * 5 Toner Supply * Memory All Clear

SERVICE PROGRAM MODE


Settings 0: Off 1: On 0 ~ 255 100 copies/step 250 ~ 10000 1 page/step 1000 pages

Japanese version only. Do not change the values.

5-590

Japanese version only. Do not change the values.

0: Off 1: On

5-801

Resets all correction data for process control and all software counters. Also, returns all modes and adjustments to the default settings. See the "Memory All Clear" section for how to use this SP mode correctly. Touch Start for over 3 seconds, then turn the main power switch off and on.

Start

Normally, this SP mode should not be used. It is used only after replacing the NVRAM, or when the copier malfunctions due to a damaged NVRAM. The LCD coordinates are also cleared, see LCD Touch Panel Calibration.

550

4-35

Service Tables

SERVICE PROGRAM MODE


Mode No. (Class 1 , 2 & 3) 5-802 Printer Free Run Function * Performs a free run. The scanner scans once and the printer prints for the number of copies requested. To perform the free run, select ON 1) Select ON. 2) Select Exit. 3) Select Copy Mode. 4) Make the required settings (such as the number of copies.). 5) Press the Start key. After finishing the free run, return this SP to OFF 5-803 Input Check 1~ 14 Output Check 1~ 97 Displays the signals received from sensors and switches. See the "Input Check" section for details. Turns on the electrical components individually for test purposes. See the "Output Check" section for details.

June 30, 1998


Settings OFF ON

5-804

ON OFF

5-807

5-811

5-812

Option Connection Check 1 ADF Checks the connectors to the optional 2 Bank peripherals. 3 LCT 4 Finisher Machine Serial Number * Use to input the machine serial number. (Normally done at the factory.) This serial number will be printed on the system parameter list. Use the key to input A. Service Tel. No. Setting Service * Use this to input the telephone number of 1 the service representative (this is displayed Telephone Number at SC when a service call condition occurs.) Condition Press the key to input a pause. Press the "Clear modes" key to delete the telephone number. * Use this to input the fax number of the 2 Service Fax service representative (this is printed on the Number for Counter Report UP mode, System No.19) Counter Printing Press the key to input a pause. Press the "Clear modes" key to delete the telephone number. CSS Function Function 1 Setting 2 CE Call

0: Not connected 1: Connected

5-816

* Japanese version only. Do not change the values. * Japanese version only. Do not change the values.

Off On Off On

550

4-36

June 30, 1998


Mode No. (Class 1 , 2 & 3) 5-821 CSS PI Device Code Function * Japanese version only. Do not change the value. 5-822 Server Data Clear

SERVICE PROGRAM MODE


Settings 0~4 1/step 0 Start

5-907

5-914

5-915

* Clears all archive file data stored in the HDD. (A printer controller is required for the archive file feature.) Before (or after) performing SP5-131, do this SP mode. After this, ask the user to restore the archive files. Plug & Play (Brand Name and Production Name Setting) Selects the brand name and the production name for Windows 95 Plug & Play. This information is stored in the NVRAM. If the NVRAM is defective, these names should be registered again. After selecting, press the Original Type key and # key at the same time. When the setting is completed, the beeper sounds five times. Printer Counter Display * Selects whether or not the total printer counter is displayed in the UP mode. Mechanical Counter Detection Checks whether the mechanical counter inside the inner cover is connected or not.

Off On 0: Not detected 1: Detected 2: Unknown 170 ~ 185 1C /step 177C

5-920

Low Power Mode Recovery Time * Determines the recovery time from low power mode. 177C: Approx. 20s 170C: Approx. 30s Copy Server Password Display * Selects whether to display the password when a file with a password is selected on the copy server. SMC Print 1 All Prints all the system parameter lists. See the "System Parameter and Data Lists" section for how to print the lists. 2 SP Prints the SP mode data list. See the "System Parameter and Data Lists" section for how to print the lists. 3 User Program Prints the UP mode data list. See the "System Parameter and Data Lists" section for how to print the lists. 4 Logged Data Prints the machine status history data list. See the "System Parameter and Data Lists" section for how to print the lists.

5-940

Normal Display password Start

5-990

Start

Start

Start

550

4-37

Service Tables

SERVICE PROGRAM MODE


Mode No. (Class 1 , 2 & 3) 5-990 SMC Print 5 Copy Program No. 10 Function

June 30, 1998


Settings Start

6-006

Prints the Copy Mode list (UP Mode No.10) See the "System Parameter and Data Lists" section for how to print the lists. 6 SP Prints the SP mode data list with a large font size. (Large Font) See the "System Parameter and Data Lists" section for how to print the lists. Use SP mode when sending the SMC list by fax. DF Registration Adjustment 1 Side-to-Side * Adjusts the printing side-to-side registration in the ADF mode. Use the key to toggle between + and -. 2 Leading Edge (Thin Original) * Adjusts the original stop position. Use the key to toggle between + and -. 3 Leading Edge (Duplex-front) * Adjusts the original stop position against the original left scale in one-sided original mode. Use the key to toggle between + and -. * Adjusts the original stop position against the original left scale in two-sided original mode. Use the key to toggle between + and -.

Start

-3 ~ +3 0.1 mm/step + 0.0 mm -29 ~ +29 0.18 mm/step + 0.0 mm -29 ~ +29 0.18 mm/step + 0.0 mm -29 ~ +29 0.1 mm/step + 0.0 mm

Reading Edge (Duplex-rear)

6-007

ADF Input Check 1 Group 1

Displays the signals received from sensors and switches of the ADF. See the "Input Check" section for details. Displays the signals received from sensors and switches of the ADF. See the "Input Check" section for details.

Group 2

6-008

ADF Output Check Turns on the electrical components of the ADF individually for test purposes. See the "Output Check" section for details.

6-009

ADF Free Run (Two-sided original) Performs an ADF free run in two-sided 1 original mode. Press 1 to start. This is a general free run controlled from the copier. For more detailed free run modes, see the Test Points/Dip Switches/LEDs section.

OFF ON

550

4-38

June 30, 1998

SERVICE PROGRAM MODE


Settings - 1~ +3.5 0.5 mm/step +0.0 mm

Mode No. Function (Class 1 , 2 & 3) 6-105 Stapling Position Adjustment * Adjusts the stapling position in the main scan direction Use the key to toggle between + and -. A larger value causes the stapling position to shift outward. 6-113 Punch Hole 1 2-Holes Adjusts the punch hole position in the subscan direction for the punch unit with two punch holes. Use the key to toggle between + and -. A larger value shifts the punch holes towards the edge of the paper. Adjusts the punch hole position in the subscan direction for the punch unit with three punch holes. Use the key to toggle between + and -. A larger value shifts the punch holes towards the edge of the paper.

- 7.5 ~ + 7.5 0.5 mm/step 0 mm

3-Holes

- 7.5 ~ + 7.5 0.5 mm/step 0 mm


Service Tables

550

4-39

SERVICE PROGRAM MODE

June 30, 1998

Mode No. Function (Class 1 , 2 & 3) 7-001 Main Motor (Drum Motor) Operation Time * Displays the total drum rotation time. 7-002 Original Counter 1 Total * Displays the total number of fed originals. 2 3 7-003 Copy Copy Server * Displays the total number of fed originals in copy mode. * Displays the total number of fed originals in copy server mode. * Displays the total number of prints in all modes. * Displays the total number of prints in copy mode. * Displays the total number of prints in printer mode. * Displays the number of sets of copies per original when making 10 or more sets of copies. e.g.: When making 15 sets of copies of an original, this counter value will increase by 6.

Settings Min.

Copy Counter 1 Total Count 2 4 Copy Printer

7-006

C/O, P/O Counter 1 C/O

7-101

7-201

* Displays the number of sets of prints per original data when making 10 or more sets of prints. e.g.: When making 15 sets of prints of an original data, this counter value will increase by 6. Copy Counter Paper Size 5 A4 Sideways * Displays the total number of prints by paper 6 A5 Sideways * size. 14 B5 Sideways * 38 LT Sideways * 44 HLT Sideways * 128 Other Sizes * 132 A3 * 133 A4 Lengthwise * 134 A5 Lengthwise * 141 B4 * 142 B5 Lengthwise * 160 DLT * 164 LG * 166 LT Lengthwise * 172 HLT * Lengthwise Total Scan Count * Displays the total number of scanned originals.

P/O

550

4-40

June 30, 1998

SERVICE PROGRAM MODE


Settings

Mode No. Function (Class 1 , 2 & 3) 7-202 Original Counter By Size 4 A3 * Displays the total number of scanned 5 A4 * originals by original size. 6 A5 * 13 B4 * 14 B5 * 32 DLT * 36 LG * 38 LT * 44 HLT * 128 Other Sizes * 7-204 Copy Counter Paper Tray 1 1st Paper Tray * Displays the total number of sheets fed from 2 2nd Paper * each paper feed tray. Tray 3 3rd Paper * Tray th 4 4th Paper * 4 tray - Japanese version only Tray 5 LCT * 6 By-pass Feed * 7-205 Total ADF Counter * Displays the total number of originals fed by the ADF. 7-206 Staple Counter * Displays the total number of staples used. 7-207 Punch Counter * Displays the total number of hole punch operations. 7-301 Total Copy By Reproduction Ratio 1 32% ~ 49% * Displays the total number of prints by 2 50% ~ 99% * reproduction ratio. 3 100% * 4 101% ~ 200% * 5 201% ~ 400% * 6 Direct Mag. * Direct Size 7 * Mag. 8 Size Mag. * 9 Fixed Mag. * Total Copies By Copy Mode 1 Letter * Displays the total number of prints by copy 2 Letter/Photo * mode. 3 Photo * 4 Generation * 5 Pale * 6 Punch * 7 Multiple Copy * 8 Sort * 9 Staple *

7-304

550

4-41

Service Tables

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 7-304 Total Copies By Copy Mode 10 Combine * Displays the total number of prints by copy 11 Erase Copy * mode. 12 Duplex Copy * 13 ADF * 14 Double * 15 2-sided * Original 16 Interrupt * 17 Combine * Mode - 1 Side 18 Combine * Mode - 2 Side Mini Book 19 * Mode Magazine 20 * Mode 21 Batch (SADF) * Mode 22 Mixed Size * Mode 23 Thin Original * 7-305 Total Copies in Multiple Copy Mode 1 1 to 1 * Displays the total number of prints by 2 1 to 2 ~ 5 * multiple copy quantity. 3 1 to 6 ~ 10 * 4 1 to 11 ~ 20 * 5 1 to 21 ~ 50 * 6 1 to 51 ~ 100 * 7 1 to 100 ~ 300 * 8 1 to 301 ~ * 7-306 Copy : Each Mode Job 1 Sort * Displays the total number of copy jobs that 2 Staple * have been done for various modes. 3 Punch * 4 Next Job * 5 Sample Copy * 7-320 Copy Server : Scanned Storage Total Number 1 * Displays the total number of stored originals of Original in the copy server. Scan 7-321 Copy Server : Each Size of Original 4 A3 * Displays the total number of stored originals 5 A4 * in the server by size. 6 A5 * 13 B4 * 14 B5 * 32 DLT * 36 LG * 38 LT *

June 30, 1998


Settings

550

4-42

June 30, 1998

SERVICE PROGRAM MODE


Settings

Mode No. Function (Class 1 , 2 & 3) 7-321 Copy Server : Each Size of Original 44 HLT * 128 Other Size * 7-323 Copy Server : Each Size of Cpies 5 A4 Sideways * Displays the total number of prints made 6 A5 Sideways * from the copy server by paper size. 14 B5 Sideways * 38 LT Sideways * 44 HLT Sideways * 128 Other Sizes * 132 A3 * 133 A4 Lengthwise * 134 A5 Lengthwise * 141 B4 * 142 B5 Lengthwise * 160 DLT * 164 LG * 166 LT Lengthwise * 172 HLT * Lengthwise 7-324 Copy Server : Print Job 1 Duplex * Displays the total number of copy jobs 2 Sort * made from the copy server. 3 Staple Print * Job Punch Print 4 * Job 5 Sample Copy * 6 First Page * Print 7-325 Copy Server : Print Job Page Distribution 1 1 * Displays the number of jobs by number of 2 2 * pages, made from the copy server. 3 3-5 * 4 6 - 10 * 5 11 * 7-326 Copy Server : Print Job File Distribution 1 1 * Displays the number of jobs by the number 2 2-5 * of consecutive files in the job, made from 3 6 - 10 * the copy server. 4 11 * 7-327 Copy Server : Print Job Set Distribution 1 1 to 1 * Displays the total number of prints by 2 1 to 2 ~ 5 * multiple copy quantity, using the copy 3 1 to 6 ~ 10 * server. 4 1 to 11 ~ 20 * 5 1 to 21 ~ 50 * 6 1 to 51 ~ 100 * 7 1 to 100 ~ 300 * 8 1 to 301 ~ *

550

4-43

Service Tables

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 7-328 Copy Server : Copy Number of Each Job 1 Duplex Copy * Displays the total number of duplex prints of one-sided originals from the copy server. 2 Duplex * Display the total number of prints of twoOriginal sided originals from the copy server. 7-330 Tandem Job * Japanese version only 7-331 Tandem : Copy Copy Number * Japanese version only 1 of Master Copy Number * Japanese version only 2 of Slave 7-332 Tandem : Copy Number of Each Master Mode 1 Original Mode * Japanese version only : Text 2 Original Mode * : Text/Photo 3 Original Mode * : Photo Original Mode * 4 : Generation Original Mode * 5 : Pale 6 Punch * 7 Repeat * 8 Sort * 9 Staple * 10 Series * 11 Erase * 12 Duplex Copy * 13 ADF Mode * 14 Double Copy * Duplex 15 * Original 16 Interrupt * 17 Combine 1 * Side 18 Combine 2 * Side 19 Booklet * 20 Magazine * 21 Batch Mode * 22 Mixed Sizes * 23 Thin * 7-333 Tandem : Copy Number of Each Slave Mode Original Mode * Japanese version only 1 : Text Original Mode * 2 : Text/Photo 3 Original Mode * : Photo

June 30, 1998


Settings

550

4-44

June 30, 1998

SERVICE PROGRAM MODE


Settings

Mode No. Function (Class 1 , 2 & 3) 7-333 Tandem : Copy Number of Each Slave Mode 4 Original Mode * Japanese version only : Generation 5 Original Mode * : Pale 6 Punch * 7 Repeat * 8 Sort * 9 Staple * 10 Series * 11 Erase * 12 Duplex Copy * 13 ADF Mode * 14 Double Copy * 15 Duplex * Original 16 Interrupt * 17 Combine 1 * Side 18 Combine 2 * Side 19 Booklet * 20 Magazine * 21 Batch Mode * 22 Mixed Sizes * 23 Thin * 7-401 Total SC Counter * Displays the total number of service calls that have occurred. 7-403 SC History 1 Latest 2 Latest 1st 3 Latest 2nd 4 Latest 3rd 5 Latest 4th 6 Latest 5th 7 Latest 6th 8 Latest 7th 9 Latest 8th 10 Latest 9th Total Jam Counter

* Displays the latest 10 service call codes. * * * * * * * * *

7-501

7-502

* Displays the total number of copy jams and original jams. Total Copy Jam Counter * Displays the total number of copy jams. Total Original Jam Counter * Displays the total number of original jams.

7-503

550

4-45

Service Tables

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 7-504 Copy Jam Counter by Jam Location 1 At Power On * Displays the total number of copy jams by location. These are jams when the paper does not activate the sensor. 3 1st Paper Tray * (1st Paper Feed Sensor) 2nd Paper 4 * (2nd Paper Feed Sensor) Tray 5 3rd Paper * (3rd Paper Feed Sensor) Tray 6 4th Paper * (Not Used) Tray 7 LCT Relay * Sensor 8 Relay Sensor * (Not Used) 1 9 Relay Sensor * (Not Used) 2 Relay Sensor * (Not Used) 10 3 Relay Sensor 11 * (Not Used) 4 12 Relay Sensor * 13 Registration * Sensor 15 Fusing Exit * Sensor 16 Exit Sensor * 19 Duplex * Entrance Sensor Duplex Relay 20 * (Duplex Transport Sensor 1) Sensor 1 21 Duplex Relay * (Duplex Transport Sensor 2) Sensor 2 22 Duplex Relay * (Duplex Transport Sensor 3) Sensor 3 23 Duplex Exit * (Not Used) Sensor 25 Entrance * Sensor Fin. Upper Tray 26 * Exit Sensor Fin. Shift Tray Exit * 27 Sensor Fin. Stapler Tray 28 * Entrance Sensor Fin. Stapler Tray 29 * Paper Sensor Fin.

June 30, 1998


Settings

550

4-46

June 30, 1998

SERVICE PROGRAM MODE


Settings

Mode No. Function (Class 1 , 2 & 3) 7-504 Copy Jam Counter by Jam Location 30 Entrance * Displays the total number of copy jams by Sensor - PP location. * These are jams when the paper does not 31 Proof Tray activate the sensor. Exit Sensor PP 32 Relay Sensor * PP Exit Sensor 33 * PP 34 By-pass Tray * 51 53 54 55 56 57 58 59 60 61 62 63 65 66 69 At Power On 1st Paper Tray 2nd Paper Tray 3rd Paper Tray 4th Paper Tray LCT Relay Sensor Relay Sensor 1 Relay Sensor 2 Relay Sensor 3 Relay Sensor 4 Relay Sensor Registration Sensor Fusing Exit Sensor Exit Sensor Duplex Entrance Sensor Duplex Relay Sensor 1 Duplex Relay Sensor 2 Duplex Relay Sensor 3 Duplex Exit Sensor * These are jams when the paper stays at the sensor. * (1st Paper Feed Sensor) * (2nd Paper Feed Sensor)

* (Not Used) * * (Not Used) * (Not Used) * (Not Used) * (Not Used) * * * * *

70 71 72 73

* (Duplex Transport Sensor 1) * (Duplex Transport Sensor 2) * (Duplex Transport Sensor 3) * (Not Used)

550

4-47

Service Tables

* (3rd Paper Feed Sensor)

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 7-505 Original Jam Counter by Jam Location 1 At Power On * Displays the total number of original jams by location. 3 ADF Feed-in * (Entrance and Registration Sensor) Sensor ADF Feed-out * (Exit and Inverter Sensor) 4 Sensor 7-506 Jam Counter by Copy Size 4 A4 Sideways * Displays the total number of copy jams by 6 A5 Sideways * paper size. 14 B5 Sideways * 38 LT Sideways * 44 HLT Sideways * 128 Other Size * 132 A3 * 133 A4 Lengthwise * 134 A5 Lengthwise * 141 B4 Lengthwise * 142 B5 Lengthwise * 160 DLT * 164 LG * 166 LT Lengthwise * * 172 HLT Lengthwise 7-507 Jam History 1 Copy : Latest * Displays the following items for the most 2 Latest 1 st * recent 10 jams. 3 Latest 2 nd * 1. Last 5 digits of the total counter value 4 Latest 3 rd * 2. Paper size 5 Latest 4 th * 3. Detected position 6 Latest 5 tht * 4. Stuck or not fed 7 Latest 6 th * 8 Latest 7 th * 9 Latest 8 th * 10 Latest 9 th * 11 Original : * Latest 12 Latest 1 st * 13 Latest 2 nd * 14 Latest 3 rd * 15 Latest 4 th * 16 Latest 5 tht * 17 Latest 6 th * 18 Latest 7 th * 19 Latest 8 th * 20 Latest 9 th *

June 30, 1998


Settings

550

4-48

June 30, 1998


Mode No. (Class 1 , 2 & 3) 7-801 ROM Version Display 1 Main Function Displays the ROM versions. MAIN: LCDC: SIB: HDC: CSS (P1) BAN: Displays the ROM versions. ADF: FIN: Print Post (Mailbox): Printer:

SERVICE PROGRAM MODE


Settings

Options

7-803 7-804 7-807

PM Counter Display * Displays the PM counter since the last PM. PM Counter Reset Resets the PM counter. SC/Jam Counter Reset Resets the SC and jam counters. Press Start to reset. Start
Service Tables

Start

7-808

Counters Reset Resets the following counters: Press Start to reset. All counters of SP7-003 All counters of SP7-006 All counters which are listed on the counter list (UP1-19-2) Start

7-810

Access Code Clear Resets both the key operator code and the weekly timer code (Key operator code for off setting). Press Start to reset. Copy Counter Reset Paper Tray 1 Paper Tray 1 Resets the total copy counter by paper tray. 2 Paper Tray 2 Use these SP modes when replacing the 3 Paper Tray 3 pick-up, feed, and separation rollers in the 4 Paper Tray 4 paper feed stations. 5 LCT (Tray 4 is not used) 6 By-pass Tray Copy Counter Reset - Magnification Resets all counters of SP7-301. Copy Counter Reset Image Edit Modes Resets all counters of SP7-303. Total Counter Reset Resets the electrical total counter. Usually, this SP mode is done at installation. This SP mode works only once when the counter value is negative Start

7-816

Start

7-822 7-823 7-825

Start Start Start

550

4-49

SERVICE PROGRAM MODE


Mode No. Function (Class 1 , 2 & 3) 7-902 SC Details 1 Latest Displays details about latest SCs. Not all 2 Latest 1st SCs have these details. 3 Latest 2nd 7-904 Copy Counter Reset Copy Mode Resets all counters of SP7-304. 7-905 Copy Counter Reset Multiple Copy Mode Resets all counters of SP7-305. 7-906 Clear Original Number of Each size Resets all counters of SP7-202. 7-907 Clear Job Number of Each size Resets all counters of SP7-306. 7-908 Copy : Clear Original Number Resets all counters of SP7-002-2. 7-920 Copy Server : Clear Scanned Storage Resets the counter of SP7-320. 7-921 Copy Server : Clear Original Number of Each Size Resets all counters of SP7-321. 7-923 Copy Server : Clear Print Number of Each Copy Resets all counters of SP7-323 7-924 Copy Server : Clear Print Job Logging Resets all counters of SP7-324 7-925 Copy Server : Clear Print Job Page Distribution Resets all counters of SP7-325 7-926 Copy Server : Clear Print Job File Distribution Resets all counters of SP7-326 7-927 Copy Server : Clear Print Job Set Distribution Resets all counters of SP7-327.

June 30, 1998


Settings

Start Start Start Start Start Start Start Start Start Start Start Start

550

4-50

June 30, 1998

SERVICE PROGRAM MODE

4.2.3 TEST PATTERN PRINTING (SP2-902)


NOTE: Do not operate the machine until the test pattern is printed out completely. Otherwise, an SC may occur. 1. Access the SP mode which contains the test pattern you need. 2. Touch the Copy Mode key on the operation panel to access the copy mode display. 3. Select the paper size. 4. Press the Start key to print the test pattern. 5. After checking the test pattern, exit copy mode by touching the SP Mode key. 6. Exit the SP mode.

Test Pattern Table (SP2-902-2: Test Pattern Printing IPU)


No. 0 1 2 3 4 5 6 Test Pattern None Grayscale 1 Grayscale 2 Grayscale 3 Grayscale 4 Grayscale 5 Vertical Lines (256-greyscale) No. 7 8 9 10 11 12 13 Test Pattern Vertical Lines (1-dot) Vertical Lines (2-dot) Hatch Pattern Cross Pattern Slant Pattern Cross Stitch (400 dpi) Cross Stitch (600 dpi)

Test Pattern Table (SP2-902-3: Test Pattern Printing Printing)


No. 0 1 2 3 4 5 6 7 8 9 10 Test Pattern None Vertical Line (1-dot) Horizontal Line (1-dot) Vertical Line (2 dot) Horizontal Line (2-dot) Grid Pattern (Single-dot) Grid Pattern (Double-dot) Alternating Dot Pattern Full Dot Pattern Black Band Trimming Area No. 11 12 13 14 15 16 17 18 19 20 21 Teat Pattern Argyle Pattern 16 Grayscales (Horizontal) 16 Grayscales (Vertical) 16 Grayscales (Vert./Hor.) 16 Grayscales (Vert./Hor Overlay) Not used Horizontal Line (1-dot) Grid Pattern (Single-dot) Grid Pattern (Double-dot) Alternating Dot Pattern Blank Page

550

4-51

Service Tables

SERVICE PROGRAM MODE

June 30, 1998

4.2.4 INPUT CHECK


Main Machine Input Check (SP5-803)
1. Access SP mode. 2. Select the class 3 SP number which will access the switch or sensor you wish to check. 3. Check the status of the sensor or switch. NOTE: If you wish to change to another class 3 level, press the Next or Prev. key. 4. The reading (0 or 1) will be displayed. The meaning of the display is as follows.
Bit 7 | 0 Bit 6 | 0 Bit 5 | 0 Bit 4 | 0 Bit 3 | 0 Bit 2 | 0 Bit 1 | 0 Bit 0 | 0

Class 3 no. 1 (Paper Feed 1)

Bit no. 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2

Description Paper Size 1 Switch Paper Size 2 Switch Paper Size 3 Switch Paper Size 4 Switch Paper Size 5 Switch 2nd Near End Sensor Not Used 1st Near End Sensor Not used Not used Tray Construction 1 Tray Construction 2 Not Used Not Used 3rd Tray Set Detection 3rd Near End Sensor Left Tandem Tray Set Detection 2 (Connector) Side Fence Positioning Sensor Base Plate Down Sensor Rear Fence HP Sensor Side Fence Close Sensor Rear Fence Return Sensor

Reading 0 On On On On On Not detected Not detected 1 Off Off Off Off Off Near end Near end

2 (Paper Feed 2)

4 : 0 , 5 : 1 Export 4 : 1 , 5 : 1 Japan

3 (Paper Feed 3)

Set Not Detected Set Not Detected Not Detected Not Detected Open Not detected

Not Set Near end Not set Fence Detected Detected At home Position Closed Return position

550

4-52

June 30, 1998 Class 3 no. 3 (Paper Feed 3) Bit no. 1 Description Left Tandem Paper End Sensor Right Tandem Tray Set Detection 2 (Connector) 1st Paper Feed Sensor 2nd Paper Feed Sensor 3rd Paper Feed Sensor Not used Not used Not used Not used Not used 1st Lift Sensor 2nd Lift Sensor 3rd Lift Sensor Not used 1st Paper End Sensor 2nd Paper End Sensor 3rd Paper End Sensor Not used Not used Not used Not used Not used 3rd Tray Down Switch 3rd Tray Down Sensor 3rd Tray Motor Lock 3rd Tray Paper Set Not used Not used Not used Not used Paper Feed Motor Lock Toner Overflow Switch Toner Collection Bottle Set Switch Toner Collection Motor Sensor

SERVICE PROGRAM MODE Reading 0 Not paper end 1 Paper end

0 4 (Paper Feed 4) 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0

Set Paper detected Paper detected Paper detected

Not set No paper No paper No paper

Not paper end Not paper end Not paper end

Paper end Paper end Paper end

6 (3rd Paper Feed Tray)

On Not detected Normal No Paper

Off Overload Overload Detected

7 (Toner Collection)

Overload Full Set Pulse

Normal Not full Not set Pulse

550

4-53

Service Tables

5 (Paper Feed 5)

Lifted Lifted Lifted

No paper No paper No paper

SERVICE PROGRAM MODE Class 3 no. 8 (I/O Board Dip Switch 101) Bit no. 7 Description Dip Switch 8 On

June 30, 1998 Reading 0 Off 1

9 (Motor Lock /Transport)

10 (Duplex)

6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0

Dip Switch 7 Dip Switch 6 Dip Switch 5 Dip Switch 4 Dip Switch 3 Dip Switch 2 Dip Switch 1 Drum Motor Lock By-pass Feed Motor Lock Development Motor Lock Fusing Motor Lock Not Used Fusing Exit Sensor Exit Sensor Tray Paper Limit Sensor Duplex Entrance Sensor Duplex Transport 3 Sensor Duplex Transport 2 Sensor Duplex Transport 1 Sensor Duplex Jogger HP Sensor Duplex Connection Toner Pump Connection Guide Plate Position Sensor LCT Motor Lock LCT Tray Down Switch LCT Connection LCT Cover Open Switch LCT Paper End Sensor LCT Down Sensor LCT Lift Sensor LCT Paper Height 1 Sensor Fusing Zero Cross Not Used Front Door Safety Switch Not Used

On On On On On On On Overload Overload Overload Overload Paper detected Paper detected Not full Detected Detected Detected Detected Not detected Connected Connected In position Overload On Connected Closed Paper end Not detected Layout Not detected Detected Closed

Off Off Off Off Off Off Off Normal Normal Normal Normal No paper No paper Full Not detected Not detected Not detected Not detected Detected Not Connected Not Connected Out of position

11 (LCT1)

7 6 5 4 3 2 1 0

Normal
Off Not connected Open Not paper end Detect Not lifted Detected Not detected Open

12 (LCT2)

7 6 5 4

550

4-54

June 30, 1998 Class 3 no. 12 (LCT2) Bit no. 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Description LCT Paper Height 2 Sensor LCT Paper Height 3 Sensor LCT Near End Sensor LCT Paper Feed Sensor LCT Paper Position Sensor Toner End Sensor By-pass Tray Switch Relay Sensor By-pass Paper End Sensor Registration Sensor Not Used Not Used Not used Not used Key Counter Set Total Counter Set Polygon Motor Cooling Fan Lock Toner Recycling Sensor Drum Unit Set Fusing Unit Set

SERVICE PROGRAM MODE Reading 0 Not detected Not detected Not detected Paper detected Detected Toner End Closed Paper detected Not paper end Paper detected 1 Detected Detected Near end Paper end Not detected Not toner end Open No paper Paper end No paper

13 (By-pass)

(Unit Set)

Set Set No lock Pulse Set Set

Not set Not set Lock Pulse Not set Not set

Table 1: 2nd Tray Paper Size Switch Combination


Class 3 no. 1 Bit 7 0 0 1 0 0 0 0 1 1 1 1 Bit 6 1 0 0 1 0 0 0 0 1 1 1 Bit 5 1 1 0 0 1 0 0 0 0 1 1 Bit 4 1 1 1 0 0 1 0 0 0 0 1 Bit 3 1 1 1 1 0 0 1 0 0 0 0 Paper Width A/B size version Inch version A3 DLT 81/4 x 13 81/2 x 14 A4 lengthwise LT lengthwise A4 sideways LT sideways HLT 81/2 x 13 sideways 8 x 101/2 A5 sideways 8 x 10 8K lengthwise 8 x 13 (Taiwan Version only) 16K lengthwise 10 x 14 (Taiwan Version only) 16K sideways 11 x 15 (Taiwan Version only) * *

550

4-55

Service Tables

14

SERVICE PROGRAM MODE

June 30, 1998

ADF Input Check (SP6-007)


Class 3 no. 1 Bit no. 7 6 5 4 3 2 1 0 2 7 6 5 4 3 2 1 0 Description Original Set Sensor Original Width Sensor 1 Original Width Sensor 2 Original Width Sensor 3 Entrance Sensor Registration Sensor Exit Sensor Inverter Sensor DF Position Sensor APS Start Sensor Feed Cover Sensor Exit Cover Sensor Bottom Plate HP Sensor Bottom Plate Position Sensor Pick-up Roller HP Sensor Not used 0 No Original No Original No Original No Original No Original No original No original No original Down Start Close Close At home position Detected At home position Reading 1 Original detected Original detected Original detected Original detected Original detected Original detected Original detected Original detected Up Off Open Open Not home position Not detected Not home position

550

4-56

June 30, 1998

SERVICE PROGRAM MODE

4.2.5 OUTPUT CHECK


NOTE: Motors keep turning in this mode regardless of upper or lower limit sensor signals. To prevent mechanical or electrical damage, do not keep an electrical component on for a long time.

Main Machine Output Check (SP5-804)


1. Access SP mode 5-804. 2. Select the SP number that corresponds to the component you wish to check. 3. Press 1, then press 7 to check that component. 4. Press 0 to interrupt the test. 5. If you wish to check another component, press the Next or Prev. Key.

No. 1 2 3 4 5 6 7, 8 9 10 11 12 13 14 15, 16 17 18 19 20 ~ 23 24 25 26 27 28 29 ~ 30 31 32 33 34 35 36 37

Description 1st Paper Feed Clutch 2nd Paper Feed Clutch 3rd Paper Feed Clutch Not Used By-pass Feed Clutch Paper Feed Clutch (LCT) Not used 1st Pick-up Solenoid 2nd Pick-up Solenoid 3rd Pick-up Solenoid Not Used By-pass Pick-up Solenoid Pick-up Solenoid (LCT) Not used 1st Separation Roller Solenoid 2nd Separation Roller Solenoid 3rd Separation Roller Solenoid Not used Rear Fence Motor LCT Motor (LCT) Paper Feed Motor By-pass Feed Motor Drum Motor Not used Fusing/Duplex Motor 1st Vertical Relay Clutch 2nd Vertical Relay Clutch 3rd Vertical Relay Clutch Not used Relay Clutch Not used

No. 38 39 40 41 42 43 44 45 46 47~ 52 53 54 55 56 57 58 ~ 62 63 64 65, 66 67 68 69 70 71 ~ 73 74 75 76 77 78 79 80

Description Relay Clutch (LCT) Registration Motor Guide Plate Solenoid Inverter Gate Solenoid Not used Duplex Transport Clutch Duplex Feed Clutch Duplex Inverter Gate Solenoid Reverse Roller Solenoid Not used Development Motor Toner Recycling Motor Not used Toner Supply Motor Transfer Belt Solenoid Not used Charge Corona Grid Plate Not used Development Bias Not used Transfer Belt Bias ID Sensor Not used Optics Cooling Fan Duplex Cooling Fan Exhaust Fan (Low speed) Exhaust Fan (High speed) Fusing Fan Not used Tray Junction Gate Solenoid (Finisher)

550

4-57

Service Tables

SERVICE PROGRAM MODE


No. 81 82 83 84 85 86 87 88 89 Description Stapler Junction Gate Solenoid (Finisher) Positioning Roller Solenoid (Finisher) Not used Mechanical Counter Upper Transport Motor (Finisher) Lower Transport Motor (Finisher) Shift Tray Exit Motor (Finisher) Staple Hammer Motor (Finisher) Punch Motor (Punch Unit) No. 90 91 92 93 94 95 96 97 98 ~ 99

June 30, 1998


Description Laser Diode Not used Tray Lift Motor (Finisher) Jogger Motor (Finisher) Stapler Motor (Finisher) Stack Feed-out Belt Motor (Finisher) Shift Motor (Finisher) Stapler Rotation Motor (Finisher) Not used

ADF Output Check (SP6-008)


No. 1 2 3 4 5 6 7 8 9 10 Description Feed-in Motor (Forward) Feed-in Motor (Reverse) Transport Motor (Forward) Transport Motor (Reverse) Feed-out Motor Exit Gate Solenoid Inverter Gate Solenoid DF Indicators Pick-up Motor (Forward) Bottom Plate Motor

4.2.6 SYSTEM PARAMETER AND DATA LISTS (SMC LISTS)


1. Access the SP mode corresponding to the list that you wish to print. 1) SP5-990-1 : All system parameter list 2) SP5-990-2 : SP mode data list 3) SP5-990-3 : UP mode data list 4) SP5-990-4 : Machine status history data list 5) SP5-990-5 : Copy mode list (UP mode No.10) 6) SP5-990-6 : SP mode data list with a large font size 2. Touch the Copy Mode key to access the copy mode display. 3. Select the paper size and press the Start key to print the list. 4. After printing the list, exit the copy mode display by touching the SP Mode key. 5. Exit SP mode.

550

4-58

TOUCH SCREEN CALIBRATION

June 30, 1998

6.13 TOUCH SCREEN CALIBRATION


After doing a memory all clear or when the touch panel detection mechanism is not working properly, calibrate the touch screen as follows. 1. Press the following keys in sequence to enter touch screen calibration mode. K 1 9 9 3 C x5 k
Self Diagnostic Menu [a] ROM Checksum Test [b] System RAM R/W Test [c] Video RAM R/W Test [d] ROM/RAM Test [e] LCD Test [f] Touch Screen Test [g] Key Test [h] LED Test [i] Op.Panel Emulation [j] LCD Information [k] Code Dump [l] Interface Test Execute [#] Touch Screen Adj. [0] ARS Test [*] Process Test [p] Debug Tools [q] Exit

A229R690.WMF

2. The Self Diagnostics Menu screen will appear. Press the # key to select the Touch Screen Adj. Mode.
Touch Screen Adj.

Touch the upper left corner and then the lower right corner of the panel using a pointed tool.

A229R691.WMF

NOTE: Do not execute any of the other items in the self diagnostic menu. 3. The Touch Screen Adj. calibration screen will appear. Touch the upper left corner then the lower right corner of the panel using a pointed (but not sharp!) tool. 4. Touch a few spots on the LCD touch panel, and confirm that the marker (a small circle) appears on the screen at exactly the same location as where it is touched. If it does not, touch Cancel on the adjustment screen. Then repeat the calibration procedure. 5. Touch Ok on the adjustment screen. 6. Touch [q] Exit and Execute to exit the self diagnostics menu.

6-110 AF 550

CNG TY TNHH SIU THANH


PHNG O TO

DANH MC LI

550/551/650/700/850

COMPANY., LTD

Reset SC Level A : Vao SP# Mode --> Tat roi m cong tac chnh

SERVICE CALL CONDITION 101


+ en chup h Loi en chup + Mau trang tieu chuan khong c do + Board cap nguon cho en chup h + Cac chan ket noi en chup khong chnh xac thay chnh xac khi thc hien Shading + Gng phan Scan d hoac nam ngoai v tr + SBU Board h hoac ket noi khong tot + Lens Block khong ung v tr + Mau trang khong ung v tr hoac qua d + Scan Home Position Sensor h Loi v tr Scan 1 + Scan Home Position Sensor khong do + Scan Home Position Sensor khong c ket noi tot c ieu kien On khi khi ong may + Scan Motor h hoac sao chup + Scan Motor khong c ket noi tot + I/0 Board h + Scan Home Position Sensor h Loi v tr Scan 2 + Scan Home Position Sensor khong do + Scan Home Position Sensor khong c ket noi tot c ieu kien Off khi khi ong may + Scan Motor h hoac sao chup + Scan Motor khong c ket noi tot + I/0 Board h + Board cao ap h Loi Charge Output 1 + ien ap hoi tiep t Charge Corona Unit + Ket noi Charge Corona Unit xau qua cao + Board cao ap h Loi Charge Output 2 + Tn hieu Trigger PWM cho Charge + Ket noi Charge Corona Unit xau Corona Unit qua cao + Board cao ap h Loi Charge Output 3 + Tn hieu Trigger PWM cho Charge Grid + Ket noi Charge Corona Unit xau qua cao + Board cao ap h Loi Charge Output 4 + Ket noi Charge Corona Unit xau + ien ap hoi tiep t Charge Grid qua cao + Charge Corona Wire Cleaner Motor h Loi chui day Charge 1 + au chui day Charge khong tr ve v tr + Board cao ap h + IOB h Home + Charge Corona Wire Cleaner Motor khong ket Loi chui day Charge 2 noi + Charge Corona Wire Cleaner Motor khong ket noi + Motor Polygonal hoac Board ieu khien h Loi Motor Polygonal + Motor Polygonal khong at c van toc + Ket noi gia Motor Polygonal va SBICU khong tot hoat ong trong 20s sau khi tn hieu + Tn hieu hoi tiep t Board ieu khien Polygonal cho Polygonal Motor On Motor khong chnh xac hoac b khoa + Tn hieu hoi tiep van hoat ong trong 20s sau khi tn hieu ieu khien cho Polygonal Motor Off

120

121

302-1 302-2 302-3 302-4 303-1 303-2 320

AF550

321

322

Loi khong co tn hieu ghi cua Laser (FGATE) + Tn hieu ghi cua Laser (F-GATE) khong xuong mc thap trong 15s sau khi giay sao chup ti Rigistration Sensor Loi ong bo Laser Tia 1 + Tn hieu ong bo tia Laser 1 khong do c bang Board do ong bo ngang khi au ban tia Laser (Laser Diode) hoat ong Dong ien cho Laser Diod qua cao + LD Drive Board ap dong cao hn 110mA cho Laser Diode Loi ong bo Laser Tia 2 + Tn hieu ong bo tia Laser 2 khong do c bang Board do ong bo ngang khi au ban tia Laser (Laser Diode) hoat ong Loi v tr cua LD Unit 1 + LD Unit Home Position Sensor khong c On khi LD Unit di chuyen en v tr Home Loi v tr cua LD Unit 2 + LD Unit Home Position Sensor khong c Off khi LD Unit ri v tr Home

+ SBICU h + Printer Controller ket noi xau hoac h .

323 326

327

328

329

350-1

ieu chnh iem tia cua LD Unit khong chnh xac + LD Unit Home Position Sensor khong c On khi v tr cua LD Unit thay oi cho chnh xac hoac khi thay oi o phan giai . Loi ID Sensor 1 + Mot trong nhng gia tr ien ap ra cua ID Sensor c do thay hai lan lien tuc khi thc hien kiem tra mau ID Sensor - Vsp = 2.5V - Vsp = 0.0V

+ Ket noi gia Laser Synchronization Detector Board va LD Unit xau . + Laser Synchronization Detector Board nam ngoai v tr va goc nhan tia khong chnh xac + Laser Synchronization Detector Board h + LD Unit h + LD Unit h + Ket ni gia LD Unit va SBICU xau + SBICU h + Ket noi gia Laser Synchronization Detector Board va LD Unit xau . + Laser Synchronization Detector Board nam ngoai v tr va goc nhan tia khong chnh xac + Laser Synchronization Detector Board h + LD Unit h + LD Unit Home Position Sensor h hoac ket noi xau + LD Unit Position Motor h hoac ket noi xau + Di chuyen cua LD Unit b khoa do khong chnh xac trong ket noi c kh quay + LD Unit Home Position Sensor h hoac ket noi xau + LD Unit Position Motor h hoac ket noi xau + Di chuyen cua LD Unit b khoa do khong chnh xac trong ket noi c kh quay + Sau khi thc hien SP# 2-109-3 hoac SP# 2109-4 khong hoan thanh + Khong thc hien SP# 2-109-3 hoac SP# 2-1094 khi thay LD Unit + Khoi c kh cua LD Unit Drive b can khong the ieu chnh tia . + + + + + + + ID Sensor h Chan cam cua ID Sensor h ID Sensor va IOB ket noi xau ID Sensor d Vung lay mau ID Sensor tren be mat Drum loi Charge hoac Development Bias Board h IOB h

AF550

350-2

350-3

Loi ID Sensor - 2 + Mot trong nhng gia tr ien ap ra cua ID Sensor c do thay hai lan lien tuc khi thc hien kiem tra mau ID Sensor - Vsg < 2.5V - Vsg = 0.0V + Khi ID Senor kiem tra , ien ap ra cua ID Sensor la 5.0V khi tn hieu PWM vao ID Sensor la 0 Loi ID Sensor - 3 + ien ap ra cao nhat cua ID Sensor khong at 2.5V hai lan lien tuc trong 2s

+ + + + + + +

ID Sensor h Chan cam cua ID Sensor h ID Sensor va IOB ket noi xau ID Sensor d Vung lay mau ID Sensor tren be mat Drum loi Charge hoac Development Bias Board h IOB h

350-4

350-5

360 361 362

365 370-1

ID Sensor h Chan cam cua ID Sensor h ID Sensor va IOB ket noi xau ID Sensor d Vung lay mau ID Sensor tren be mat Drum loi Charge hoac Development Bias Board h IOB h ID Sensor h Loi ID Sensor - 4 Chan cam cua ID Sensor h + Mot trong nhng gia tr ien ap ra cua ID Sensor va IOB ket noi xau ID Sensor c do tai trang thai ban ID Sensor d au cua ID (ID Setting) Vung lay mau ID Sensor tren be mat Drum loi - Vsg < 4.0V khi PWM = 255 Charge hoac Development Bias Board h - Vsg > 4.0V khi PWM = 000 IOB h ID Sensor h Loi ID Sensor - 5 Chan cam cua ID Sensor h + Vsg khong at c gia tr ngng (4.0V ID Sensor va IOB ket noi xau + 0.2V) khi thc hien kiem tra Vsg ID Sensor d (Setting ID SP# 3-001) Vung lay mau ID Sensor tren be mat Drum loi Charge hoac Development Bias Board h IOB h Ket noi xau gia HDD va HDD Controller Board Loi Hard Disk Drive 1 Nguon cho HDD b ngat . + SBICU h + May khong do thay tn hieu ket noi t HDD hoac HDD Controller Board h HDD SC Code hien th khi thc hien SP# 4-911-1 , Loi Hard Disk Drive 2 s dung SP# 4-911-2 e sa cha + D lieu lu trong HDD khong the xuat ra + HDD h chnh xac + SBICU h Loi IMAC (Image Compression IC) + Loi xay ra khi thc hien x ly anh trong + HDD Controller Board h IMAC , khi ieu khien nen va truyen tai d lieu hnh anh + SBICU h Loi a ch lu hnh anh + BICU nhan tn hieu yeu cau d lieu hnh anh cho d lieu khong lu trong bo nh + Potential Sensor h . + IOB h Loi Potential Sensor 1 + Khi xac nh Drum Potential Sensor khi + IOB va Potential Sensor ket noi xau thc hien Process Control , Potential + Drum Unit va IOB ket noi xau + Development Bias Board h Sensor nam ngoai gia tr ch nh

+ + + + + + + + + + + + + + + + + + + + + + + + +

AF550

370-2

370-3

370-4

Loi Potential Sensor 2 + Khi xac nh Drum Potential Sensor khi thc hien Process Control , gia tr Charge ma Potential Sensor o c tren be mat Drum nam ngoai gia tr ch nh Loi Potential Sensor 3 + Khi ieu chnh VG cho ien ap li khi thc hien Process Control , -1000V (VG) c ap len li , Potential Sensor se do c khoang 900V (VD). Nhng gia tr VD do c vt qua 970V Loi Potential Sensor 4 + Khi ieu chnh VD khi thc hien Process Control , Potential Sensor do thay VD co gia tr ln hn VG Loi Potential Sensor 5 + Khi ieu chnh VH cho ien ap LD khi thc hien Process Control , au tien la thc hien tao mau VH , Potential Sensor do thay VH cao hn 500V Loi Potential Sensor 6 + Khi ieu chnh VG cho ien ap li khi thc hien Process Control , -1000V (VG) c ap len li , Potential Sensor se do c khoang 900V (VD). Tuy nhien gia tr VD do c khong at 900V + 10V sau 5 lan ieu chnh Loi Potential Sensor 7 + Khi ieu chnh VH cho Halftone khi thc hien Process Control , Potential Sensor do thay VH do c khong at 300V + 20V sau LD a thay oi 2 lan Loi TD Sensor - 1 + Tn hieu ra cua TD Sensor thap hn 0.5V hoac cao hn 5V trong 10 lan o c khi sao chup Loi TD Sensor - 2 + Khi thc hien Setting TD Sensor (SP# 2801) . - Thap hn 2.5V khi PWM = 255 - Cao hn 2.5V khi PWM = 000 Loi TD Sensor - 3 + Khi thc hien SettingTD Sensor (SP# 2801) , ien ap ra cua TD khong ieu chnh ve 2.5V + 0.1V. trong 20s

+ + + +

Potential Sensor h . + IOB h IOB va Potential Sensor ket noi xau Drum Unit va IOB ket noi xau Development Bias Board h

+ + + + + + + + + + + + + + + + + + +

Potential Sensor h . + IOB h IOB va Potential Sensor ket noi xau Drum Unit va IOB ket noi xau Development Bias Board h Day Charge d hoac b lao hoa Potential Sensor h . + IOB h IOB va Potential Sensor ket noi xau Drum Unit va IOB ket noi xau Development Bias Board h Day Charge d hoac b lao hoa Potential Sensor h . + IOB h IOB va Potential Sensor ket noi xau Drum Unit va IOB ket noi xau LD Unit h Day Charge d hoac b lao hoa Potential Sensor h . + IOB h IOB va Potential Sensor ket noi xau Drum Unit va IOB ket noi xau Development Bias Board h

370-5

370-6

370-7

390-1

390-2

+ + + + + + + + + + + +

Potential Sensor h . + IOB h IOB va Potential Sensor ket noi xau Drum Unit va IOB ket noi xau LD Unit h Be mat Drum d TD Sensor h TD Sensor khong ket noi hoac ket noi xau IOB h Ket noi gia TD Sensor va IOB xau TD Sensor h IOB h Ket noi gia TD Sensor va IOB xau

390-3

+ TD Sensor h + IOB h + Ket noi gia TD Sensor va IOB xau

AF550

391 401-1 401-2

Loi ien ap cua Development Roller + Tn hieu Development Bias r ien c do thay . Loi r ien Transfer Bias Roller + Tn hieu r ien Transfer Bias Roller c do thay Transfer Bias Roller h + Khong co tn hieu hoi tiep t Transfer Bias Roller Loi en Quenching + Sau khi hoan tat Process Control , ien tch tren be mat Drum do bang Potential Sensor nam ngoai gii han bnh thng Main Motor b khoa + Tn hieu ong bo hoi tiep t Main Motor lau hn 2s sau khi Main Motor quay Development Motor b khoa + Tn hieu ong bo hoi tiep t Development Motor lau hn 2s sau khi Development Motor quay Polygonal Mirro Cooling Fan Motor b khoa + Tn hieu ong bo hoi tiep t Polygonal Mirro Cooling Fan Motor lau hn 5s sau khi Motor quay Loi phan hoi mc thai + Tn hieu t Toner Recycling Sensor khong thay oi trong 500ms sau khi Drum Motor On Loi bnh mc thai + Switch bnh mc thai van mc Off Loi Toner Recycling Motor + Tn hieu Toner Recycling Motor van Off Loi nang khay th nhat

430

+ + + + + + + + + + +

Board cao ap h Development Bias Terminal ket noi xau Ket noi xau tai Board cao ap Board cao ap h Day cap ket noi khong ket noi hoac h Transfer Bias Roller khong cam Board cao ap h Day cap ket noi khong ket noi hoac h Transfer Bias Roller khong cam Tiep xuc cua PCU xau (Ground Drum) en Quenching h hoac ket noi vao Board Charge xau

440 441

+ + + + + +

C kh Main Motor b qua tai Main Motor hoac Board ieu khien h Main Motor ket noi xau C kh Development Motor b qua tai Development Motor hoac Board ieu khien h Development Motor ket noi xau

491

+ Polygonal Mirro Cooling Fan Motor h hoac ket noi xau + C kh Polygonal Mirro Cooling Fan Motor b ket

495

496 497 501 502 503

+ Qua tai phan c kh hoi mc thai + Toner Recycling Sensor khong ket noi tot + Toner Recycling Clutch khong ket noi tot hoac h + Khong co bnh mc thai + Toner Collection Bottle Switch h + Toner Recycling Motor khong c ket noi

+ Motor nang khay co s co hoac khong ket noi + Tray Lift Sensor h hoac khong ket noi Loi nang khay th hai + Giay trong khay ket hoac c cau c kh gia Loi nang khay th ba khay va Motor + Tray Lift Sensor khong c tac ong + Can cua Pick-up Roller co s co sau khi Tray Lift Motor on trong 10s + Tray Lift Sensor a c tac ong khi khay giay c ay vao may

AF550

506

507

508

509

510

511

521-1

Loi Feed Motor khay giay + Tn hieu ong bo hoi tiep cua Motor khong do c trong 50ms sau khi Motor hoat ong LCT Main Motor b khoa (Option) + Tn hieu ong bo hoi tiep cua Motor khong do c trong 50ms sau khi Motor hoat ong Loi Motor ay giay t khay ben trai qua khay ben phai cua Tandem + No can 10s hoac hn e Rear Fence Return Sensor On sau khi Rear Fence Drive Motor hoat ong + No can 10s hoac hn e Rear Fence Home Position Sensor On sau khi Rear Fence tr ve Home + Khi ay khay vao , Rear Fence Home Position Sensor va Rear Fence Return Sensor eu On Loi Motor thanh vo bien giay Tandem - 1 + Khi Side Fence Motor On e m Side Fence , Side Fence Home Position Sensor khong On trong 2s + Khi Side Fence Motor On e ong Side Fence , Side Fence Close Sensor khong On trong 2s Loi nang khay LCT (Option) + LCT Lift Sensor (Sensor gii han nang) khong c tac ong trong 18s sau khi Motor nang/ha khay On + LCT Lower Limit Sensor (Sensor gii han ha) khong c tac ong trong 18s sau khi Motor nang/ha khay On + LCT Lift Sensor a c tac ong khi nap LCT ong xuong sau khi nap giay + Khi thc hien nang khay giay , LCT Lift Sensor khong c tac ong trong 2.5s sau khi Paper End Sensor c On Loi Motor thanh vo bien giay Tandem - 2 + Khi Side Fence Motor On e ong Side Fence , Side Fence Close Sensor khong On trong 2s Loi thanh vo bien giay Duplex - 1 + Khi thanh vo bien giay tr ve Home , Jogger Home Position Sensor khong c On neu Jogger Fence Motor di chuyen Jogger Fence 153.5mm

+ Paper Tray Unit Main Motor h + Paper Tray Unit Main Motor h ket noi khong tot + C kh tai cua Main Motor qua nang + LCT Main Motor h + LCT Main Motor h ket noi khong tot + C kh tai cua Main Motor qua nang + + + + Rear Fence Drive Motor h Rear Fence Home Position Sensor h Rear Fence Return Sensor h Ket c kh

+ Side Fence Motor h hoac ket noi xau + Ket c kh Side Fence

+ + + + +

LCT Motor co s co hoac khong ket noi LCT Lift Sensor h hoac khong ket noi LCT Lower Limit Sensor h hoac khong ket noi Pick-Up Solenoid h hoac khong ket noi Paper End Sensor h

+ Side Fence Motor h hoac ket noi xau + Ket c kh Side Fence

+ Jogger Motor h hoac ket noi xau + Ket c kh thanh vo giay (Jogger Fence) + Jogger Home Position Sensor h hoac khong ket noi

AF550

521-2

530 531

541 (A) 542 (A) 543 (A) 545 (A) 546 (A) 547 (A) 590

Loi thanh vo bien giay Duplex - 2 + Khi thanh vo bien giay i t Home , Jogger Home Position Sensor khong c Off neu Jogger Fence Motor di chuyen Jogger Fence 153.5mm Loi Feed Motor cua khay giay tay + Tn hieu ong bo hoi tiep khong do c trong 20s khi Feed Motor On Loi Motor Fusing/Duplex + Tn hieu ong bo van khong do c trong 2s sau khi Fusing/Duplex Motor hoat ong Thermistor say h + Nhiet o say do t Thermistor thap hn 70C trong 16s Loi nhiet o say + Nhiet o say khong at c nhiet o Standby trong 300s sau khi cong tac chnh m . Loi qua nhiet - 1 + Nhiet o say do bang Thermistor cao hn 2310C trong 5s Loi qua nhiet - 2 + en say sang toan phan trong 45s khi ang Stanby , sau khi hoan thanh khi ong Loi nhiet o say khong on nh + Nhiet o say thay oi tang len 200C hoac ha xuong 200C so vi nhiet o Stanby sau khi khi ong hoan thanh Loi tn hieu Zero Cross + Tn hieu Zero Cross khong do c trong nao o sau khi cong tac chnh m Loi Toner Collection Motor + Tn hieu ra cua Toner Collection Motor Sensor khong thay oi trong 3s khi Toner Collection Motor On

+ Jogger Motor h hoac ket noi xau + Ket c kh thanh vo giay (Jogger Fence)

+ Manual Feed Motor h hoac ket c kh

+ Fusing/Duplex Drive Motor h + Cleaning Roller (Fusing Unit) qua d , ap len dan en qua tai Fusing/Duplex Motor + IOB h + Thermistor h , cong , ket noi khong tot hoac nam ngoai v tr + + + + + + + + Thermistor h hoac nam ngoai v tr en say t . + Thermostat h BICU h . + Board nguon h Fusing Unit khong c ket noi tot Thermistor h Board nguon h (PSU) IOB hoac BICU h Thermistor khong nam ung v tr

+ Thermistor ket noi khong chat + Fusing Unit ket noi khong chat

+ Board nguon h + Nhieu tren mang li ien

601 602

+ Toner Collection Motor h hoac khong ket noi + Toner Collection Motor Sensor h hoac khong ket noi . + Ket c kh phan ra bnh mc thai + IOB h + Ket noi gia SBU va SBICU Board khong tot Loi lien lac gia BICU va SBU + SBICU khong lien lac c vi SBU chnh + SBU hoac SBICU h xac Loi lien lac gia BICU va HDD Controller + Ket noi gia SBICU va HDD Controller Board khong tot Board + HDD Controller Board hoac SBICU h + BICU khong lien lac c vi HDD Controller Board chnh xac

AF550

620-1 620-2 620-3 621 623

624 630 700

Loi lien lac gia SBICU va ARDF - 1 + Tn hieu TXD va RXD gia SBICU va ARDF Board khong on nh Loi lien lac gia SBICU va ARDF - 2 + Tn hieu TXD va RXD gia SBICU va ARDF Board khong on nh Loi lien lac gia SBICU va ARDF - 3 + Software loi sau khi hoat ong s dung khong bnh thng Loi lien lac gia SBICU va Finisher + SBICU khong lien lac c vi Finisher Board chnh xac Loi lien lac gia SBICU va Paper Feed Board + SBICU khong lien lac c vi Paper Feed Board chnh xac Loi lien lac gia SBICU va LCT + SBICU khong lien lac c vi LCT Board chnh xac Loi lien lac vi CSS Loi Pick-Up cua ARDF + Tn hieu Pick-Up Home Position Sensor khong thay oi sau khi Pick-Up Motor On . Loi nang khay ban goc ARDF + Bottom Plate Position Sensor (Sensor nam canh khoi Feed) khong c tac ong sau khi Original Table Motor nang khay ban goc Loi Motor vo giay Finisher + Finisher Jogger Home Position Sensor khong c tac ong trong mot thi gian quy nh khi tr ve Home + Finisher Jogger Home Position Sensor van c tac ong trong mot thi gian quy nh khi ri Home Loi Motor bam khim Finisher + Tac vu bam kim khong hoan thanh trong thi gian quy nh sau khi Staple Hammer Motor (Motor bam kim) On Loi Motor ay giay ra (sau khi bam khi) + Stack Feed-Out Belt Home Position Sensor khong c tac ong trong thi gian nao o sau khi Stack Feed-Out Motor On

+ + + + +

Serial ARDF Nhieu ARDF Serial

Line ket noi gia BICU va ARDF Board h Board hoac SBICU h tren ng Serial Line Board hoac SBICU h Line ket noi gia BICU va ARDF Board h

+ Software loi

+ + + +

Serial Line ket noi gia SBICU va Finisher loi Finisher Board hoac SBICU h Nhieu tren ng Serial Line Serial Line ket noi gia SBICU va Paper Feed Board loi + Paper Feed Board hoac SBICU h + Nhieu tren ng Serial Line + Ket noi gia SBICU va LCT loi + LCT Board hoac SBICU h + SP# 5-816 ang at On + Pick-Up Home Position Sensor h + Pick-Up Motor h + Board ARDF h + Bottom Plate Home Position Sensor (Sensor nam tai ay khay ban goc) h + Bottom Plate Position Sensor (Sensor nam tren , canh khoi Feed) h + Bottom Plate Motor hoac ARDF Board h + Jogger Home Position Sensor h + Jogger Drive Motor h

701

722

724

+ Ket kim bam + Bam kim qua tai do nhieu giay + Staple Hammer Motor h + Stack Feed-Out Belt Home Position Sensor h + Stack Feed-Out Motor h + Stack Feed-Out Motor qua tai

725

AF550

726

727

729

730

900 951

953

954

Loi Motor di/nang khay Finisher + Tac vu di khay khong hoan thanh trong thi gian quy nh sau khi Shift Motor (Motor lac khay) On . + Stack Heigth Sensor khong c tac ong trong thi gian nao o sau khi Shift Tray Lift Motor (Motor nang khay) On Loi Motor xoay khoi bam kim Finisher + Khoi Stapler xoay khong hoan thanh trong thi gian quy nh sau khi Stapler Rotation Motor (Motor xoay khoi bam kim) On . + Khoi Stapler khong ve v tr Home cua no trong thi gian quy nh sau khi tac vu bam kim hoan thanh Loi Motor bam lo Finisher + Sau Punch Motor On , Punch Home Position Sensor khong c tac ong trong thi gian quy nh Loi v tr Motor bam kim Finisher + Stapler Home Position Sensor On lau hn bnh thng sau khi Stapler Motor (Motor di chuyen khoi bam kim) On e di chuyen khoi Stapler tr ve v tr Home + Stapler Home Position Sensor khong c tac ong trong khoang thi gian quy nh sau khi Stapler Motor On e di chuyen khoi Stapler ri v tr Home Loi Counter ien t + Counter ien t la hang so Loi tn hieu F-Gate - 2 + Sau khi IPU a nhan tn hieu F-Gate (laser writing start trigger signal) , no nhan c tn hieu F-Gate khac Loi cai at Scanner + Nhng cai at can thiet cho Image Processing s dung Scanner khong c gi t IPU Loi cai at Printer + Nhng cai at can thiet cho Image Processing s dung Printer Controller khong c gi t IPU

+ Shift Motor h hoac qua tai + Shift Tray Lift Motor h hoac qua tai

+ Stapler Rotation Motor h hoac qua tai + Stapler Rotation Motor khong ket noi hoac ket noi xau .

+ Punch Home Position Sensor h + Punch Motor h hoac qua tai + Punch Motor khong ket noi hoac ket noi xau . + Stapler Motor h hoac qua tai + Stapler Home Position Sensor h + Stapler Motor khong ket noi hoac ket noi xau

+ NVRAM h + Software loi + BICU h

+ Software loi

+ Software loi

AF550

955

959

960 961 962 963 964

980 981

982 990

Loi cai at Memory + Nhng cai at can thiet cho Image Processing s dung Memory (bo nh) khong c gi t IPU Loi cai at ID Printer + ID can thiet cho Image Processing s dung Printer Controller khong c gi t IPU Loi hoi ve ID Printer + ID gi t Printer Controller sau khi ket thuc viec in ra khong chnh xac Loi san sang ID Printer + ID gi t Printer Controller trong khi ieu kien san sang in khong chnh xac Loi cai at ID Memory + ID gi t bo nh khi IPU gi tn hieu bo nh san sang khong chnh xac Loi hoan thanh ID Memory + ID gi t bo nh khi IPU gi tn hieu bo nh hoan thanh khong chnh xac Loi san sang Printer + Tn hieu Printer san sang khong phat ra trong 17s sau khi IPU nhan c tn hieu khi ong Printer Loi truy xuat HDD + Khong chnh xac trong cac tham so gi t IPU em MSU Loi tn hieu ap tra HDD + HDD Controller Board khong phat ra tn hieu ap tra nao khi IPU gi tn hieu doc/ghi en MSU Loi cau truc HDD + HDD khong co ac tnh ky thuat chnh xac khi lap at Loi thc hien Software + Software thc hien khong ung chc nang.

+ Software loi

+ Software loi

+ Software loi

+ Software loi

+ Software loi

+ Software loi

+ Software loi

+ Software loi + Ket noi gia IPU va MSU xau + Software loi + Ket noi gia IPU va MSU xau + HDD h + HDD h + HDD khong chnh xac ve chunh loai + Software h + Internal parameter (tham so) khong chnh xac + Software defective

10

AF550

You might also like