You are on page 1of 45

Design of base plate Project/Client :S.

No 1 Design forces Factored Axial load Nature of axial load Factored Shear force Dia of anchor bolts (HT bolts) No of bolts Grade of bolts Ultimate Tensile strength of bolt Ultimate Tesile strength of plate Yield stress of plate Yield stress of bolt Cube compressive strength of concrete 2 Geometric properties Column section Depth of section Width of flange Clearence of holes Dia of holes = Nominal dia of bolt + clearence Minimum Edge distance Maximum edge distance = = = = = = = 12t = = (250/fy) = Edge distance provided = O.K 25 25 16 450 150 50 150 150 192 mm
1/2

Calculations

References

Pu = Fy = = = = fu = fcu = fy = fyb = fck = M 20

17 KN 2 KN mm 4 Nos 8.8 100 Mpa 250 Mpa 250 Mpa 250 Mpa 20 Mpa ISMB 400 mm 140 mm 2 mm 22 mm 33 mm

From analysis

= Compression

Clause 10.2.4 IS:800:2007

1 150 mm

100

30

140

400 50

200

50

450 Minimum spacing of bolts (2.5 d) Maximum spacing of bolts (lesser of 32t or 300) Spacing of bolt provided 3 Check for base pressure Bearing pressure of plate Allowable bearing pressure w = Pu/Ap = = 0.6fck = Safe 4 Check for Minimum Thickness of base plate Thickness of plate required Clause 7.4.3.1 IS:800:2007 12 Mpa 0.19 Mpa = = = O.K 50 mm 300 mm 150 mm Clause 10.2.2 & 10.2.3 IS:800:2007

t s 2.5w(a 2 0.3b 2 ) mo / fy tf
ts = Thickness of plate required 4 Check for shear capacity of bolts Design shear strength of bolt, Nominal shear capacity, Vnsb Vnsb = Vdsb = Calculated shear force per bolt 5 Check for bearing capacity of bolts Design bearing strength of bolts Vdpb = Vnpb/mb Vnpb = 2.5kb d t fu kb = 0.4 32 KN 25.6 KN 4.25 KN Safe 6 Check for tension capacity of bolts Design tension capacity of bolt Nominal Tensile capacity of bolt Tnp = 0.9fubAn<fybAsb(mb/mo) 0.9fubAn = N.G Mpa Tdp = Tnp/mb Vnpb = Vdpb = Calculated bearing strength of bolt Vb = Vd = Safe Clause 10.3.4 IS:800:2007 32.63 KN 26.104 KN 0.5 KN Vdsb = Vnsb/mb = Safe Clause 10.3.3 IS:800:2007 1.22 mm 16 mm

fybAsb(mb/mo) = Nominal Tensile capacity of bolt Design tension capacity of bolt Calculated tension per bolt 7 Check for combined shear and tension Tnp = Tdp = T = N.G

N.G Mpa N.G Mpa N.G Mpa N.G Mpa

N.G N.G

N.G N.G

N.G

> N.G

1.0

Design of base plate Project/Client :S.No 1 Design forces Axial load Nature of axial load Bending moment about xx Bending moment about yy Lataral force along xx Lataral force along yy Dia of anchor bolts (HT bolts) No of bolts 2 Geometric properties Pu = Mx = My = Fx = Fy = = = M 20 156 KN 0 KN.m 0 KN.m 0 KN 0 KN mm 4 Nos From analysis = Compression Calculations References

Dia. Of pile Width of column/pedestal Depth of column/pedestal Minimum spacing of piles Centre to Centre distance of two adjacent pile

= = = = =

300 mm 450 mm 700 mm 750 mm 750 mm As per IS:2911Part-1, clause:5.6

Edge projection from face of piles (Min 100-150mm) Width of pile cap Length of pile cap Depth of pile cap ( assumed) Clear cover to the reinforcement Grade of concrete Grade of Steel 3 Load calculations Weight of pile cap Additional load due to moment Total load on each pile 4 Calculation of reinforcement a)Bending theory Bending moment about xx Design bending moment Dia of Main reinforcement Dia of secondary reinforcement Effective depth of pile cap pt Area of steel required b)Truss theory Tension at bottom Area of steel required Area of steel required (max of bending & truss theory) No of bars required No of bars provided Area of steel provided 5 Check for shear a)One way shear Percentage of steel provided Permissible shear stress, c = = = 0.145 % 17.42 0.273 Mpa Clause 40.5 = 0.87fy/6.89pt = = = = 373.68 mm 4 Nos 4 Nos 452.16 mm
2 2 2 2 = Pu/12ld(3l -a )

= = = = = fck fy = = = = = =

150 mm 600 mm 1350 mm 600 mm 75 mm 20 Mpa 415 Mpa 12.15 KN 0 KN 84.08 KN O.K As per IS:2911Part-1, clause:5.12.5

= = = = = Mu/bd2 = = = pt,min =

21.44 KN.m 32.161 KN.m 12 mm 12 mm 519 mm 0.2 0.056 % 0.12 %


2 373.68 mm

= =

97.69 KN
2 270.57 mm

Nominal shear stress ,v Shear span, av(C/C of pile/2-d/2+20% pile dia) Enhancement factor (2d/av) Modified shear strength, v

= = = = OK

0.41 Mpa 0.18 m 5.77 1.57 Mpa 1.57>0.41

IS:456-2000

b)Two way shear Punching shear, V Perrimeter of column, Punching shear stress, Permissible shear stress, = = = = 234 KN 2300 mm 0.2 Mpa 1.118 Mpa 1.11803398874989>0.2 OK Clause 31.6.3 IS:456-2000

Design of base plate Project/Client :S.No 1 Design forces Factored Axial load Nature of axial load Factored Shear force Dia of anchor bolts (HT bolts) No of bolts Grade of bolts Ultimate Tensile strength of bolt Ultimate Tesile strength of plate Yield stress of plate Yield stress of bolt Cube compressive strength of concrete 2 Geometric properties Column section Depth of section Width of flange Clearence of holes Dia of holes = Nominal dia of bolt + clearence Minimum Edge distance Maximum edge distance = = = = = = = 12t = = (250/fy) = Edge distance provided = Not OK 50 50 12 500 160 100 180 160 144 mm
1/2

Calculations

References

Pu = = Fy = = = = fu = fcu = fy = fyb = fck = M 36

1100 KN Tension 300 KN mm 4 Nos 8.8 100 Mpa 250 Mpa 250 Mpa 250 Mpa 25 Mpa BUILT-UP I SECTION 400 mm 300 mm 2 mm 38 mm 57 mm

From analysis

Clause 10.2.4 IS:800:2007

1 160 mm

200

50

300

400 100

400

100

500 Minimum spacing of bolts (2.5 d) Maximum spacing of bolts (lesser of 32t or 300) Spacing of bolt provided 3 Check for base pressure Bearing pressure of plate Allowable bearing pressure w = Pu/Ap = = 0.6fck = Safe 4 Check for Minimum Thickness of base plate Thickness of plate required Clause 7.4.3.1 IS:800:2007 15 Mpa 5.5 Mpa = = = O.K 90 mm 300 mm 180 mm Clause 10.2.2 & 10.2.3 IS:800:2007

t s 2.5w(a 2 0.3b 2 ) mo / fy tf
ts = Thickness of plate required 4 Check for shear capacity of bolts Design shear strength of bolt, Nominal shear capacity, Vnsb Vnsb = Vdsb = Calculated shear force per bolt 5 Check for bearing capacity of bolts Design bearing strength of bolts Vdpb = Vnpb/mb Vnpb = 2.5kb d t fu kb = 0.4 43.2 KN 34.56 KN 275 KN Unsafe 6 Check for tension capacity of bolts Design tension capacity of bolt Nominal Tensile capacity of bolt Tnp = 0.9fubAn<fybAsb(mb/mo) 0.9fubAn = 73.25 Mpa Tdp = Tnp/mb Vnpb = Vdpb = Calculated bearing strength of bolt Vb = Vd = Safe Clause 10.3.4 IS:800:2007 105.73 KN 84.584 KN 75 KN Vdsb = Vnsb/mb = Safe Clause 10.3.3 IS:800:2007 10.29 mm 12 mm

fybAsb(mb/mo) = Nominal Tensile capacity of bolt Design tension capacity of bolt Calculated tension per bolt 7 Check for combined shear and tension Tnp = Tdp = T =

289.02 Mpa 73.25 Mpa 58.6 Mpa 275 Mpa Unsafe

75 34.56

275 58.6

6.863

> Unsafe

1.0

You might also like