Professional Documents
Culture Documents
TP
CEB-1048 'X13-1031
COMMERCIAL
Indianapolis. Indiana
ENGINE
BULLETIN
TURBINE ASSEMBLY, NEW FIRST STAGE TURBINE WHEEL--INSTALL,ATION AND REIDENTIFICATION PLANNING EFFECTIVITY INFORMATION: All 25O-C20 Turbine CAT 31794, excluding All 250-817 CAT 60054. Turbine Assemblies CAT 31759 Assemblies
April
23,
1 OF - 6
1974
Converted 250-C20 Turbine and comply 7~f P/N 6853306 incorporated. NOTE:
is
The above effectivity applies to the new first stage turbine wheel only. Some earlier turbines may incorporate -the new first and second stage turbine nozzles required with the new wheel. Turbines with l?/N 6853306 Fi~rst Stage Turbine Wheel are a.ffected.
REASON:
To provide an improved first st:xge turbine wheel that incorporates increased rim thickness to reduce the tendency for cracks to orig~inate in the rim. Also, the wheel features Alpak :Sl coating for sulfidation protection. New first and second stage nozzles featuring improved material are required with the new wheel. Compliance with this the following table: COllPLIANCE bulletin is mandatory per
COMPLIANCE:
TOTAL TIME IN SERVICE ON FIRST STAGE TURBINE WHEEL P/N 6853306 1000-1550
MANDATORY
No later than August 31, 19S1, or 1550 hours wheel total time in =x-vice or 3000 cycles, whichever shall first occur.
TP
CEB-1048 CEB-1031
COMMERCIAL
TURBINE ASSEMBLY, WHEEL--INSTALLATION Compliance (continued):
ENGINE
BULLETIN
TOTAL TIME IN SERVICE ON FIRST STAGE TURBINE WHEEL P/N 6853306 800-1000
COMPLIANCE MANDATORY
At next turbine assembly overhaul or no later than August 31, 1981, or 1550 hours wheel total time-in-service or 3000 cycles, whichever shall first occur. At next turbine assembly overhaul CT no later than February 28, 1982, or 1550 hours wheel total time-in-service or 3000 cycles, whichever shall first occur. 600 At next turbine assembly overhaul or no later than August 31, 1982, or 1550 hours wheel total time-in-service or 3000 cycles, whichever shall first occur. When the first stage turbine wheel is installed, the turbine and rotor assemblies are reidentified and a P suffix is added to the turbine serial number. The new turbine 6878496 6878426 P/N 6886407 Wheel can only be used in incorporating a P/N 6879868 ox- P/N First Stage Turbine Nozzle and a P/N Second Stage Turbine Nozzle. a
600-800
Less
than
DESCRIPTION:
INTERCHANGEABILITY:
23,
1974
TP
CEB-1048 CEB-1031
COMMERCIAL
TURRIliE ASSEMBLY, WHEEL-INSTALLATION
ENGINE
BULL-ETIN
PREREQUISITES:
To be accomplished simultaneously (CZO) or 250 TX' CZB-1028 (B17). provide a new P/N 6851531 Fourth
NOZZlt?.
APPROVAL: MANPOWER:
FAA-DER
No additional manhours accomplish this bulletin AVAILABILITY: NOMENCLATURE First Stage Turbine First Stage Turbine First Stage Turbine Second Stage Turbine Turbine Ident,ification Rivet Wheel Nozzle Nozzle Nozzle Plate
QTYjASSY. 1 1 aIt. 1 1 4
is in
installed limited
if
not
:already in May,
incorporated. 1974.
quantities
TOOLING:
cw 907 , CW 921,
23,
1974
TP
CEB-1048 CEB-1031
COMMERCIAL
TURBINE ASSEMBLY, WHEEL--INSTALLATION ACCOMPLISHMENT I. At A. II. If
time
ENGINE
BULLETIN
of
Replace P/N 6853306 First Stage P/N 6886407 First Stage Turbine not already incorporated:
A. Replace P/N 6877399, P/N 6878483 or P/N 6877500 First Stage Turbine Nozzle with new P/N 6879868 or P/N 6878496 First Stage Turbine Nozzle. B. III. Replace P/N P/N 6878426 6871482 Second Stage Second Stage Nozzle. Turbine Nozzle with new
Reidentification: A. Following incorporation of the new First Stage Turbine Wheel, the Gas Producer Turbine Rotor Assembly is reidentified from P/N 6871480 to P/N 6887194 (this P/N is located on the second stage nozzle and is applied per AS478-2Dl or 2E). B. Obtain Plate a new P/N (Blank). 6876676 Turbine Assembly Identification
information from the old to the new the turbine assembly part number and turbine serial number suffixes.
identify turbine assembly as a. For 250-B17's, 6887196. Information may be metal stamped, For 250-C2O's identify vibro-peened or scribed. turbine assembly as 6887195. b. Add a letter P as a suffix to the turbine Serial number. If the turbine has been converted from a C18, the S/N map already have B, C and A suffixes. These are to be dropped when the P is added. plate using four P/N
2.
23,
1974
TP
CEB-304s CEB-1031
COMMERCIAL
TURBINE ASSEMBLY, WHEEL--INSTALLATION
ENGINE
BULCETIN
IV.
Record compliance with 250 CEB-1048 (C20) or 250 TP CEB-1031 (B17) in the Turbine Assembly (pink pages) Modification Record, Part III of the Engine Log Book. Be sure to note in all applicable places the change to the turbine serial number.
23,
1974
TP
CEB-1048 CEB-1031
COMMERCIAL
TURBINE ASSEMBLY, WHEEL--INSTALLATION MATERIAL NEW P/N 6887195 6887196 6887194 6886407 6878426 6878496 6879868 6876676 AN125402 INFORMATION: QTY. 1 1 1 1 1 1 a1t. 1 4
ENGINE
BULLETIN
NOMENCLATURE Turbine Assg, Gas Prod. gL Power Turbine Assy, Gas Prod. & Power Rotor Assy, Turb., Gas Prod. Wheel, Turbine, 1st Stage Nozzle Assy, Turbine 2nd Stage Nozzle Assy, Turbine, 1st Stage Nozzle Assy, Turbine, 1st Stage Plate, Ident. Turb Ass?, Blank Rivet NOTES:
OLD P/N 6853329 6853328 6871480 6853306 6871482 6877399, 6878483 6877500 6876676 AN125402 or
QTY. 1 1 1 1 1 1 1 1 1 4
DISPOSITION A A A B B B B B C C
part
only.
23,
1974