Professional Documents
Culture Documents
How To: Install Autodesk Inventor 2008 and ADMS 2008 Next
to Autodesk Inventor R11 Software on a Local Machine
You must uninstall ADMS 5 or any earlier version of ADMS to ensure successful installation
of Autodesk Inventor 2008 on a local machine. Make sure that you create a backup of the
ADMS database before you uninstall ADMS 5. See the following section, Removing
ADMS 5, for further information.
1
CONTENT CENTER FOR R2008 AND R11 SIDE-BY-SIDE INSTALLATION
To install the Content Center environment on your local machine, you need to install
Autodesk Data Management Server 2008 and Inventor 2008 Content Center Libraries.
Inventor 11 Client Update for ADMS 2008 must be installed to allow version 11 Content
Center to access libraries from ADMS 2008.
Figure 1
At the end of the ADMS 2008 Installation, you are prompted to start the ADMS Console and
migrate the previous version of the ADMS database (Vault databases and Content Center
libraries). Depending on the size and number of databases, migration may take a
considerable amount of time. The migration does not have to happen necessarily at the end
of ADMS installation, but must be accomplished before you can access Content Center
libraries on the server from Inventor 11 or Inventor 2008. You can migrate the previous
version of the ADMS database the first time you launch ADMS Console. See the following
sections “Removing ADMS 5” and “Library migration,” for important information about
migrating CC libraries.
2
CONTENT CENTER FOR R2008 AND R11 SIDE-BY-SIDE INSTALLATION
Removing ADMS 5
ADMS 5 must be removed to ensure successful installation of ADMS 2008. Note that when
you remove ADMS, you remove the ADMS software, but not the ADMS (Microsoft® SQL)
database which remains on the machine. The ADMS database contains the Vault databases
and Content Center libraries which were managed by the previous ADMS software. This
ADMS database is migrated and managed by the newly installed ADMS 2008 software.
To remove ADMS software:
1. Make sure that you create a backup of ADMS database before you remove ADMS 5.
Figure 2
2. In Control Panel > “Add or Remove Programs“ select Autodesk Data Management Server
5, and click Remove.
Figure 3
Note: The ADMS database must stay on the machine. The database contains all the
Autodesk Inventor and user Content Center libraries, which will continue to be used by the
Autodesk Inventor 11 software.
Library Migration
At the end of the ADMS 2008 installation, you are prompted to start the ADMS Console
(Figure 4). The default value for the prompt to migrate is Yes. It launches ADMS Console
when installation of Autodesk Inventor 2008 is completed.
3
CONTENT CENTER FOR R2008 AND R11 SIDE-BY-SIDE INSTALLATION
Figure 4
The first time ADMS Console starts, it looks for existing ADMS databases for migration. The
ADMS database, with all the Autodesk Inventor 11 and user Content Center libraries, is
located and submitted for migration. The following prompts appear:
Figure 5
Select (Yes) to process the ADMS database migration into the new ADMS database schema.
Select Autodesk Inventor 11 and 2008 to migrate Content Center libraries to support both
version 11 and 2008 of the Autodesk Inventor software.
4
CONTENT CENTER FOR R2008 AND R11 SIDE-BY-SIDE INSTALLATION
Autodesk Inventor 11 Content Center libraries are migrated and left in the Inventor 11
partition so they can continue to be accessed by Inventor 11. Any Inventor 11 User libraries
are also copied to the Inventor 2008 partition so they can be used by Inventor 2008.
Libraries in the Autodesk Inventor 11 partition are available for Autodesk Inventor 11 only.
They are available for Autodesk Inventor 11 Content Center Library Configuration.
Libraries in the Autodesk Inventor 2008 partition are available for Autodesk Inventor 2008
only. They are available for the Autodesk Inventor 2008 Content Center Library
Configuration.
After the migration is complete, Content Center libraries are shown in the ADMS Console, as
shown in Figure 7. Inventor 11 standard content libraries and user libraries retain the library
names represented in the Autodesk Vault Manager on ADMS 5. Note that each of them is
shown in the “Autodesk Inventor 11” partition, which can be seen on the right side of the
ADMS Console dialog box.
Copies of version 11 user libraries are available with a prefix “AI2008_” added to their name
and are located in the “Autodesk Inventor 2008” partition. Additionally, all newly installed
Inventor 2008 standard content libraries contain the “AI2008_” prefix to their library names for
easy identification.
Figure 6
5
CONTENT CENTER FOR R2008 AND R11 SIDE-BY-SIDE INSTALLATION
How To: Uninstall ADMS 2008 and Remove ADMS 2008 (SQL) instance
Removing the ADMS (SQL) instance prior to uninstalling the ADMS software will result in a
non-functional ADMS and may result in serious complication when uninstalling ADMS
software. Make sure you follow the order of steps described below.
The list of SQL instances may display SQL instances that were installed and are
used by different software on your machine. You must remove the
AUTODESKVAULT: Database Engine only. Removing any other SQL instances may
harm the software that uses the SQL instance.
6
CONTENT CENTER FOR R2008 AND R11 SIDE-BY-SIDE INSTALLATION
Figure 7
6. Click Finish on the Confirmation page. The SQL Server Installation Wizard removes
the ADMS SQL Instance from your computer.
7
CONTENT CENTER FOR R2008 AND R11 SIDE-BY-SIDE INSTALLATION
Figure 8
Consider deleting all libraries in the Autodesk Inventor 11 partition since they consume disk
space. Remember to create a backup before you remove them.
Figure 9
Autodesk [and other products] are either registered trademarks or trademarks of Autodesk, Inc.,
in the USA and/or other countries. All other brand names, product names, or trademarks belong
to their respective holders. Autodesk reserves the right to alter product offerings and
specifications at any time without notice, and is not responsible for typographical or graphical
errors that may appear in this document.