You are on page 1of 3

1. What is POSITION 1 according to the LOAD LINE RULE? 2. Pitch of the propellerDefinition?

Distance moved in 360 Degree Rotation in a Soft Solid Fluid 3. What is the Name of the plate which Joins the STEM to the FLAT PLATE KEEL.Shoe Plate, Coffin Plate, Oxter Plate, Stealer Plate? 4. Most Efficient Pre-Painting MethodsPickling, Blast cleaning, flame Cleaning, Wire Brushing? 5. In a Shell Expansion PlanWhat is PLATE 5? i.e. Distance of4th/ 5th plate From the Fft/ Fwd and 4th/ 5th plate from the bottom? 6. What is the relation betweenPermeability, Relative Density and Stowage Factor? Formulalike( x= 1- m* RD), (m* RD-1), (RD* SF) etc 7. _______ Transverse Watertight Cargo Hold Bulkhead____________ Type of Collision Bulkhead. ( Corrugated & Plate, Swashed & Corrugated, Swashed & plate, Plate & Swashed? 8. What is it seen when a Propeller is seen from the Aft end.Leading edge, Trailing Edge, bow, tail? 9. Location of Collision Bulkhead? 5-8 % Length of the Ship! 10. Frictional Resistance Increases with.Length of the Water plane Area, Wetted Surface Area, Displacement? 11. Definition Of DISPLACEMENT of Ship Mass of the Displaced Volume Of Water! 12. IDEAL Location of AIR PIPESAt the Lowest Point Of the Tank, At the Filling Connection, At the Highest Point Of the Tank/ or Opposite to the Filling Connection! 13. Cyclic Up & Down Movement of Vessel Along the VERTICAL AXIS.Heaving, yawing, Swaying, pitching? 14. Main Purpose Of Bulbous BowTo Decrease the Specific Fuel Consumption! 15. Peak Tank Testing...2.44 m above the Highest Water Level, Hose Test, Air test etc! 16. Maximum Transverse Spacing in DOUBLE BOTTOM SPACE2.5 m, 3 m, 3.7 m, 3.8 m? 17. What is The Effect On RESERVE BUOYANCY when the ship is in Fresh Water (for same Displacement).Increases, Decreases, Remains same? 18. Rise of Floor Aids indrainage of Water From Tanks, Drainage of water from decks etc! 19. Breadth AP, 1, 2, 3, 4, FP and Coordinates 1, 1.44, 1.55, 1.33, 0.89, 0.2 LBP is 14 then Find TPC? .0.2, 0.3, 0.5, 0.6 t/cm ?

20. Find Cw and TPC ifBreadth AP,1,2,3,4,FP and Coordinates 0.9, 1.5, 2.1, 1.6, 0.9, 0.1 and LBP is 15! Ans. 0.56, 0.65, 0.34, 0.43 t/ cm ! 20. A barge of length 6.5m, Beam 10.2 m and Draft 4 m in Even Keel Condition. The ship is in water of Relative Density 1.006 t/ Cubic Meter. Find the Bodily Sinkage of the Mean Draft, if the Displacement is Constant.. 0.086, 0.076 etc!

1. Requirement for LOAD LINE REGULATION is known as Condition requirement, minimum freeboard, minimum load water Line! 2. How to support Stem Bar to radiused Plate? Breasthook! 3. how to join Stem bar to Keel PlateOxter,coffin,Shoe, Stealer paltes? 4. Transverse Framinghow support is given in Engine Room, or Pounding RegionAlternate Framing or Every Framingfill in the blanks! 5. Transverse Framing is supported by.Girder and Bracket to ship side, unsupportedetc! 6. D5 plate stands for? 7. What is must in a shaft tunnelDrainage well, water tight door, escape route to deck! 8. Ship going Forwardwhich edge of the propeller touches firstLeading/ Trailing* ? 9. Rise of floor Purpose? 10. why TPC is not same for all drafts?...Waterplane Area is not same for all drafts! 11. GM will change when? Shifting of weightLongitudinally, vertically? 12. testing of peak tanks.2.44 m above the ! 13. Extra Strengthening done where... for pounding region+ 40 % of mid ship! 14. Engine room transverse framingEvery frame, alternate etc! 15. Taylors Wake Fraction Formula. ((Va-V)/ V)! 16. Wetted Surface Area Formula C. L (BD) ^ 0.5!

17. 5 years dry dockingone Dry docking can be missed if ABS is given all the necessary informations about the ship, fire on the ship, ship less than 15 years old, good quality resistant paint in underwater hull. 18. Summer load line Displacement= 15,000 t, TPC= 26.2,ships mean draft= 6.2 m Ship is going in Winter Regionwhat is the New Displacement? 19. Hatch Coaming Minimum height600, 800, 1000, 1100 mm?

You might also like