You are on page 1of 4

Code No: RR212403 Set No.

1
II B.Tech I Semester Supplimentary Examinations, November 2007
AUTOMOBILE ENGINEERING DRAWING
(Automobile Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆

1. Draw the studded joint in position with D= 30 mm. [16]

2. Draw an eye foundation bolt with D=25 mm. [16]

3. Draw front view and side view of key with gibhead in application. [16]

4. Draw sectional front view and side view of solid flanged coupling with D=80mm.
[16]

5. Draw sectional front view and top view of double riveted, zig zag joint with dia of
rivet as 10 mm. [16]

6. Draw half sectional front view (Left half) and sectional right side view of a bushed
bearing suitable for a Journal of 50 mm diameter. [16]

7. Sketch the line diagram of gearing system in an automobile engine. [16]

8. Drawing the cross section of an eccentric and show the parts clearly. [16]

⋆⋆⋆⋆⋆

1 of 1
Code No: RR212403 Set No. 2
II B.Tech I Semester Supplimentary Examinations, November 2007
AUTOMOBILE ENGINEERING DRAWING
(Automobile Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆

1. Draw the profile with proportions of the 150 metric screw thread design of external
and internal threads. With pitch as 30 mm. [16]

2. Draw an eye foundation bolt with D=25 mm. [16]

3. Draw two views of hexagonal headed bolt and nut and square headed bolt along
with nut. (D=30mm). [16]

4. Draw sectional front view and the top view of a universal coupling connecting two
shafts of 30 mm diameter. [16]

5. Draw the sectional front view and top view of double row, zig-zag combined lap
and butt joint if the rivet diameter as 16 mm. [16]

6. Draw the sectional view of a spindle mounting making use of taper roller bear-
ings to take up radial and axial loads, possible to occur in both directions of axis
simultaneously taking the spindle diameter of 50 mm. [16]

7. Sketch the line diagram of brake drum in an automobile wheel. [16]

8. Draw the cross section of the governor of an I.C. Engine and show the important
parts of it. [16]

⋆⋆⋆⋆⋆

1 of 1
Code No: RR212403 Set No. 3
II B.Tech I Semester Supplimentary Examinations, November 2007
AUTOMOBILE ENGINEERING DRAWING
(Automobile Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆

1. Draw the thread profiles of square thread and ACME thread. [16]

2. Draw hexagonal headed bolt and nut with dia of bolt as 30 mm. [16]

3. Draw the Rag foundation bolt with D = 30mm. [16]

4. Draw sectional front view and side view of Cotter joint with socket and spigot ends
taking d=30 mm. [16]

5. Draw sectional front view and top view of double riveted, zig zag joint with dia of
rivet as 10 mm. [16]

6. Sketch the thrust bearing used for screw propeller shafts with suitable scale. [16]

7. Sketch the line diagram of steering box bracket. [16]

8. Show the cross section of carburctor ofo an I.C. Engine and indicate the parts.[16]

⋆⋆⋆⋆⋆

1 of 1
Code No: RR212403 Set No. 4
II B.Tech I Semester Supplimentary Examinations, November 2007
AUTOMOBILE ENGINEERING DRAWING
(Automobile Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆

1. Draw the profile with proportions of the 150 metric screw thread design of external
and internal threads. With pitch as 30 mm. [16]

2. Draw the single start square thread with dia of shaft as 60 mm. [16]

3. Draw an eye bolt with D=30 mm with circular cross section. [16]

4. Draw sectional front view and right side view of compression type as muff coupling
with dia of shaft as 25mm. [16]

5. Draw sectional front view and top view of the triple riveted butt joint with double
straps(zig zag type) with dia of Rivet as 18 mm. [16]

6. Draw the sectional view of a spindle mounting making use of taper roller bear-
ings to take up radial and axial loads, possible to occur in both directions of axis
simultaneously taking the spindle diameter of 50 mm. [16]

7. Sketch the line diagram of power transmission in an automobile gear box. [16]

8. Indicating the cross section and draw two views of connecting rod and show the
parts clearly. [16]

⋆⋆⋆⋆⋆

1 of 1

You might also like