Professional Documents
Culture Documents
ISO 4759-1:2000
AS 5066
Australian Standard™
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
Australian Standard™
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
COPYRIGHT
© Standards Australia International
All rights are reserved. No part of this work may be reproduced or copied in any form or by any
means, electronic or mechanical, including photocopying, without the written permission of the
publisher.
Published by Standards Australia International Ltd
GPO Box 5420, Sydney, NSW 2001, Australia
ISBN 0 7337 4848 1
ii
PREFACE
This Standard was prepared by the Standards Australia Committee ME-029, Fasteners.
The objective of this Standard is to provide manufacturers, suppliers and users with tolerances for the
principle features of product grades A, B and C metric bolts, screws, studs and nuts and product grade
A tapping screws.
This Standard is identical with and has been reproduced from ISO 4759-1:2000, Tolerances for
fasteners, Part 1: Bolts, screws, studs and nuts— Product grades A, B and C.
Statements expressed in mandatory terms in notes are deemed to be requirements of this Standard.
The term ‘informative’ has been used in this Standard to define the application of the annex to which
it applies. An ‘informative’ annex is only for information and guidance.
Attention is drawn to the possibility that some of the elements of this Standard may be the subject of
patent rights. Standards Australia shall not be held responsible for identifying any or all such patent
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
rights.
As this Standard is reproduced from an international Standard, the following applies:
(a) Its number does not appear on each page of text and its identify is shown only on the cover and
title page.
(b) In the source text ‘this part of ISO 4759’ should read ‘this Australian Standard’.
(c) A full point should be substituted for a comma when referring to a decimal marker.
References to international Standards should be replaced by references to Australian or
Australian/New Zealand Standards as follows:
CONTENTS
1 Scope ..............................................................................................................................................................1
2 Normative references ....................................................................................................................................2
3 Tolerances for metric bolts, screws and studs ..........................................................................................3
4 Tolerances for metric nuts..........................................................................................................................25
5 Tolerances for tapping screws...................................................................................................................36
Annex A (informative) Tolerances ...........................................................................................................................44
Annex B (informative) Examples of dimensioned and toleranced fasteners......................................................46
Annex C (informative) Examples of gauges and other measuring devices ........................................................49
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
1
AUSTRALIAN STANDARD
1 Scope
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
This part of ISO 4759 specifies a selection of tolerances for bolts, screws, studs and nuts with ISO metric threads
and with product grades A, B and C and for tapping screws with product grade A.
NOTE The product grades refer to the size of the tolerances where grade A is the most precise and grade C is the least
precise.
The tolerances, except tolerances for threads, are selected from the system of limits and fits specified in ISO 286-1
and ISO 286-2. The tolerances for metric threads are taken from the series of tolerance classes specified in
ISO 965-3. The tolerances for tapping screw threads are covered in ISO 1478.
The tolerances of form and position are specified and indicated in accordance with ISO 1101, ISO 8015 and
ISO 2692.
The tolerances specified in this part of ISO 4759 apply to fasteners prior to coating unless otherwise specified. See
also ISO 4042.
Deviations from the tolerances specified in this part of ISO 4759 are only permitted in product standards where
there are valid technical reasons. In cases where there is a difference between the tolerance requirements in this
part of ISO 4759 and the product standard, the product standard takes precedence.
Dimensions and tolerances given in this part of ISO 4759 are in millimetres.