Professional Documents
Culture Documents
Aim
Study the relation between the force produced and the change of momentum when a jet strikes a vane. Compare between force exerted by a jet on a flat plate and on a hemispherical surface.
Apparatus
Acrylic nozzle stainless steel enclosure with glass viewports interchangeable arcylic circular flat plate and a hemispherical cup
Theory
Momentum conservation principle is applied in order to find out the force applied by jet onto the flat-plate or spherical cup. =
F = Q V F = Q (Vin Vout)
Where, F: force applied on plate by jet Q: volumetric flow rate Vin: velocity at the time of striking of jet onto the plate. Vout: velocity of water leaving the plate.
The volumetric flow rate in the equation 'Q' is calculated with the help of measuring tank and stopwatch. = Where, H: height in measuring tank t: time taken to achieve the height Atank: base area of measuring tank ME-313, IIT Gandhinagar, Dept. of Mechanical Engineering Page 1
Where, Vnozzle: velocity of jet at the nozzle Anozzle: cross sectional area of nozzle Relation between V and Vnozzle can be given as,
in
Vin = Vnozzel 2 g S Where; g: the gravitational acceleration (9.81 m/s ). S: the distance between the jet and the plates. Schematic of jet impact on vanes has been shown in below diagram.
2
Vout generally equals Vin cos , where represents the change in direction of the jet.
For the flat plat = 90, so that Vout = 0. ME-313, IIT Gandhinagar, Dept. of Mechanical Engineering Page 2
out
= -V
in
So the following relations are used for calculating the Predicted values of the force; For the Flat plate: F = Q V
in in
The actual force exerted is calculated by the equation, F = 9.81 * w Where, w: mass of weights plus mass of plate and rod.
Procedure
Clean the apparatus and make All Tanks free from dust. Close the drain valves provided. Fix desired Vane on the apparatus. Fill Sump tank with Clean Water and ensure that no foreign particles are there. Ensure that all On/Off Switches given on the Panel are at OFF position. Now switch on the Main Power Supply (220 V AC, 50 Hz). Switch on the Pump. Regulate Flow of water through channel with the help of given Flow Control Valve. Put known value of weight on the plate. Now control the valve so that the applied weight on the top is counter balanced by the impact of jet. Measure Flow Rate using Measuring Tank and Stop Watch. Repeat the experiment with different weights. Slowly open the bypass valve. Switch off the pump.
Page 3
Data
Area of measuring tank= 0.25*0.4= 0.1 m2 Diameter of nozzle d=0.01m Area of cross section of nozzle A=d2/4=0.0000785 m2 Density of water= 1000 kg/m3 Weight of aluminum disc + rod = 14.5 gm Weight of flat plate= 89.5 gm Weight of hemispherical vane= 97.5 gm
Additional constant weights: for flat plate = 104 grams for hemispherical vane = 112 grams
Observation
A. For Flat Plate:
S.No 1 2 3 4 W (gm) 202.5 296.0 390.0 585.0 Fexp (N) 1.985 2.901 3.822 5.733 S (cm) 15.50 16.50 13.40 12.50 H (cm) 24.20 27.50 29.10 32.20 t (sec) 44.94 45.13 44.63 44.66 Q (m3/s) 0.0005385 0.0006094 0.0006520 0.0007210 Vnozzle (m/s) 6.860 7.762 8.306 9.185 Vim (m/s) 6.635 7.551 8.146 9.050 Ftheo (N) 3.456 4.476 5.210 6.430
Page 4
Sample Calculation
Flow rate = =
= 0.0242 m3
= 6.860 m/s
Page 5
Graphs
Flat Plate
7
6
Force Exerted (N) 5 4 3 2 1 0 0 2 4 6 8 10 Experimental
Theoretical
Velocity (m/s)
Hemispherical Vane
12 Force Exerted (N) 10 8 6 4 2 0 0 2 4 6 8 10 Experimental Theoretical
Velocity (m/s)
Precaution
Never start the pump when bypass valve is closed. Slowly close bypass valve in order to avoid sudden impact on the plates. Also open bypass valve slowly before switching off the pump.
Page 6
Errors
Due to use of stop watch manual errors in timings are introduced. Even though the weight was balanced, the height gradually dropped while calculating the H. This may be attributed to drop in pressure head because of drop in water level in supply tank.
Conclusion
Experimental force exerted by jet on hemispherical vane is always more than that of flat plate, and almost double to that of flat plate force. As the weight on the plats increased, higher impact velocity or jet velocity is required to counter balance the force.
Page 7