You are on page 1of 6

用 Dy namip s 做 OSPF&Rip 协议混合的实验

今天利用 Dynamips 完成了 OSPF &Rip 协议混合的实验,开始的时候找不到合适的


Cisco 的 IOS,后来无意间把 C3620 的 IOS 放上去,没想到很好用!

马上模拟了六台 C3620 出来!在我的内存=512M 的本本上还跑挺顺畅(其实我只开


了 5 台,不过够用就行)

实验过程:

先把.net 文件呈上来: (#号后面为注释,蓝色)

autostart = false
[localhost]
port = 7200
udp = 10000

[[router R1]]
image = \Program Files\Dynamips\images\c3620-i-mz.122-37.bin
model = 3620
console = 2001
ram = 32
#内存调到 32M,再小的话不知道行不行,个人认为 32M 已经很合适了
confreg = 0x2142
exec_area = 32
mmap = false
slot0 = NM-1FE-TX
#支持 1 个 Fastethernet 接口
slot1 = NM-4E
#支持 4 个 Ethernet 接口
e1/0 = R2 f0/0

[[router R2]]
image = \Program Files\Dynamips\images\c3620-i-mz.122-37.bin
model = 3620
console = 2002
ram = 32
confreg = 0x2142
exec_area = 32
mmap = false
slot0 = NM-1FE-TX
slot1 = NM-4E
e1/0 = R3 f0/0

[[router R3]]
image = \Program Files\Dynamips\images\c3620-i-mz.122-37.bin
model = 3620
console = 2003
ram = 32
confreg = 0x2142
exec_area = 32
mmap = false
slot0 = NM-1FE-TX
slot1 = NM-4E
e1/0 = R4 f0/0

[[router R4]]
image = \Program Files\Dynamips\images\c3620-i-mz.122-37.bin
model = 3620
console = 2004
ram = 32
confreg = 0x2142
exec_area = 32
mmap = false
slot0 = NM-1FE-TX
slot1 = NM-4E
e1/0 = R5 f0/0

[[router R5]]
image = \Program Files\Dynamips\images\c3620-i-mz.122-37.bin
model = 3620
console = 2005
ram = 32
confreg = 0x2142
exec_area = 32
mmap = false
slot0 = NM-1FE-TX
slot1 = NM-4E

[[router R6]] #实验中没有用到第六个路由器


image = \Program Files\Dynamips\images\c3620-i-mz.122-37.bin
model = 3620
console = 2006
ram = 32
confreg = 0x2142
exec_area = 32
mmap = false
slot0 = NM-1FE-TX
slot1 = NM-4E

拓扑图出场:以前没画过拓扑,随便画了个,凑合看吧!(汗一个先)

点击看大图

配置过程如下:
----R1 的配置----
R1#configure terminal
R1(config)#interface e1/0
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#router ospf 32
R1(config-route)#network 192.168.1.1 0.0.0.0 area 1
----R2 的配置----
R2#configure terminal
R2(config)#interface f0/0
R2(config-if)#ip address 192.168.1.2 255.255.255.0
R2(config-if)#no shutdown
R2(config)#interface e1/0
R2(config-if)#ip address 192.168.2.1 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#router ospf 32
R2(config-route)#network 192.168.1.2 0.0.0.0 area 1
R2(config-route)#network 192.168.2.1 0.0.0.0 area 0
----R3 的配置----
R3#configure terminal
R3(config)#interface f0/0
R3(config-if)#ip address 192.168.2.2 255.255.255.0
R3(config-if)#no shutdown
R3(config)#interface e1/0
R3(config-if)#ip address 192.168.3.1 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
R3(config)#router ospf 32
R3(config-route)#network 192.168.2.2 0.0.0.0 area 0
R3(config-route)#network 192.168.3.1 0.0.0.0 area 2
----R4 的配置----这个是关键
R4#configure terminal
R4(config)#interface f0/0
R4(config-if)#ip address 192.168.3.2 255.255.255.0
R4(config-if)#no shutdown
R4(config)#interface e1/0
R4(config-if)#ip address 192.168.4.1 255.255.255.0
R4(config-if)#ip address 192.168.44.1 255.255.255.0 secondary
R4(config-if)#no shutdown
R4(config-if)#exit
R4(config)#router ospf 32
R4(config-route)#network 192.168.3.2 0.0.0.0 area 2
R4(config-route)#network 192.168.4.1 0.0.0.0 area 2
R4(config-route)#redistribute rip metric 10
R4(config-route)#router rip
R4(config-route)#network 192.168.44.0
R4(config-route)#redistribute ospf 32 metric 10
----R5 的配置----
R5#configure terminal
R5(config)#interface f0/0
R5(config-if)#ip address 192.168.44.2 255.255.255.0
R5(config-if)#no shutdown
R5(config)#interface loopback 0
R5(config-if)#ip address 192.168.45.1 255.255.255.0
R5(config-if)#no shutdown
R5(config-if)#exit
R5(config)#interface loopback 1
R5(config-if)#ip address 192.168.46.1 255.255.255.0
R5(config-if)#no shutdown
R5(config-if)#exit
R5(config)#interface loopback 2
R5(config-if)#ip address 192.168.47.1 255.255.255.0
R5(config-if)#no shutdown
R5(config-if)#router rip
R5(config-route)#network 192.168.44.0
R5(config-route)#network 192.168.45.0
R5(config-route)#network 192.168.46.0
R5(config-route)#network 192.168.47.0
R5(config-route)#exit
----配置完毕----

可以用查询命令查看:
show ip route
show ip ospf data 等

You might also like