Professional Documents
Culture Documents
D EUTSCHE NORM
EN ISO 4014
Supersedes DIN EN 24014,
February 1992 edition.
European Standard EN ISO 4014 : 2000 has the status of a DIN Standard.
A comma is used as the decimal marker.
National foreword
This standard has been published in accordance with a decision taken by CEN/TC 185 to adopt, without
alteration, International Standard ISO 4014 as a European Standard.
The responsible German body involved in its preparation was the Normenausschuss Mechanische
Verbindungselemente (Fasteners Standards Committee), Technical Committee Schrauben und Muttern mit
Auenantrieb.
The DIN Standards corresponding to the International Standards referred to in clause 2 and in the bibliography of the EN are as follows:
ISO Standard
DIN Standard
ISO 225
ISO 724
ISO 898-1
ISO 3269
ISO 3506-1
ISO 4042
ISO 4753
ISO/DIS 4759-1
ISO 6157-1
ISO 8839
ISO 8992
DIN EN 20225
DIN ISO 724
DIN EN ISO 898-1
DIN EN ISO 3269
DIN EN ISO 3506-1
DIN EN ISO 4042
DIN EN ISO 4753
DIN EN ISO 4759-1*)
DIN EN 26157-1
DIN EN 28839
DIN ISO 8992
Continued overleaf.
EN comprises 14 pages.
Page 2
DIN EN ISO 4014 : 2001-03
Amendments
DIN EN 24014, February 1992 edition, has been superseded by the specifications of EN ISO 4014, which is
identical to ISO 4014.
Previous editions
DIN 932-1: 1926-01; DIN 932-2: 1926-01; DIN 600: 1926-10x; DIN 532: 1929-11x; DIN Kr 551: 1935-11,
1936-11; DIN 931-2: 1926-01, 1942-04; DIN 931: 1967-12, 1970-11; DIN 931-1: 1926-01, 1942-04, 1952-12,
1963-03, 1982-07, 1987-09; DIN ISO 4014: 1987-09, 1989-09; DIN EN 24014: 1992-02.
National Annex NA
Standards referred to
(and not included in Normative references and Bibliography)
DIN EN 20225
DIN EN 26157-1
DIN EN 28839
DIN EN ISO 898-1
DIN EN ISO 3269
DIN EN ISO 3506-1
DIN EN ISO 4042
DIN EN ISO 4753
DIN ISO 724
Bolts, screws, studs and nuts Symbols and designations for dimensioning
(ISO 225 : 1983)
Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements (ISO 6157-1 : 1988)
Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous
metals (ISO 8839 : 1986)
Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts,
screws and studs (ISO 898-1 : 1999)
Fasteners Acceptance inspection (ISO 3269 : 2000)
Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts,
screws and studs (ISO 3506-1 : 1997)
Fasteners Electroplated coatings (ISO 4042 : 1999)
Fasteners Ends of parts with external ISO metric screw thread (ISO 4753 : 1999)
ISO general purpose metric screw threads Basic dimensions (ISO 724 : 1993)
EN ISO 4014
November 2000
ICS 21.060.10
English version
2000. CEN All rights of exploitation in any form and by any means
reserved worldwide for CEN national members.
Page 2
EN ISO 4014 : 2000
Foreword
International Standard
ISO 4014 : 1999 Hexagon head bolts Product grades A and B,
which was prepared by ISO/TC 2 Fasteners of the International Organization for Standardization, has been
adopted by Technical Committee CEN/TC 185 Threaded and non-threaded mechanical fasteners and accessories, the Secretariat of which is held by DIN, as a European Standard.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, and conflicting national standards withdrawn, by May 2001 at the latest.
In accordance with the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard:
Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 4014 : 1999 was approved by CEN as a European Standard without
any modification.
Page 3
EN ISO 4014 : 2000
Page 4
EN ISO 4014 : 2000
Page 5
EN ISO 4014 : 2000
Page 6
EN ISO 4014 : 2000
Page 7
EN ISO 4014 : 2000
Page 8
EN ISO 4014 : 2000
Page 9
EN ISO 4014 : 2000
Page 10
EN ISO 4014 : 2000
Page 11
EN ISO 4014 : 2000
Page 12
EN ISO 4014 : 2000
Page 13
EN ISO 4014 : 2000
Page 14
EN ISO 4014 : 2000