Professional Documents
Culture Documents
SCHEDULE OF RATES
1. All work materials and goods described in this Schedule of Rates shall be of the respective kinds,
described in the Contract and in accordance with the instructions of the Superintending Officer.
2. The description given of each item, unless otherwise stated, be held to include the use of materials,
labour, equipment, tools and vehicles including maintenance, supply of fuel and all idle time,
conveyance, delivery, unloading, storing, hoisting, all labour setting, fitting, scaffolding and fixing in
position, all cutting and waste, return of packings, establishment charges, overheads, profits and all
forms of claims for loss and expense.
3. Unless otherwise stated, all work shall be measured nett as fixed in its place.
5. The term “as specified” means as specified in the Standard Specifications, Supplementary
Specifications and/or Drawings.
m - Linear metre
m2 - Square metre
m3 - Cubic metre
no. - Number
ltr - Litre
pc. - Piece
kg - Kilogram
ton - Tonne
pr - Pair
sht - Sheet
hr - Hour
7. The Cost of removal and disposal and the making good of all affected works shall be deemed to be
included in the Schedule of Rates unless otherwise stated.
All Schedule of Rates shall be applicable for new and replacement works.
8. All rates in the Schedule shall include all necessary materials and waste, plant, stagings and
scaffoldings (only applicable up to 6m high, any height above 6 metres shall be paid separately,
measuring from ground level, i.e. from the base for which scaffolding rests) unless specified otherwise.
1
SOR Premable Page 2
The measurement of all excavation and subsequent disposal shall be those before excavating. The increases
in bulk and any extra excavation required for planking and strutting and formwork for concrete and working
spaces under circumstances have been allowed for in the rates.
Rates for each item shall be held to include for keeping all excavation free from water and Site dry pumping
or bailing if required and providing any temporary drains required.
Ordinary Ground
Includes spoil or rubbish of every description, rubbish tip material etc., sand, gravel decomposed granite, red
or white earth, loamy or gravelly clay, gravelly laterite, mud, bog or any other formation which. is removable
by the ordinary application of pick and shovel and at any depth.
(1) Forming, cutting groves, chases, mortice, holes and making good any other sundry items of a like
nature.
(2) Extra labour for laying to falls, or cambers and preparing surfaces to receive screeds or pavings also
to be included.
(3) All tests on concrete, cement and aggregate etc as required and compliance with the strengths as
specified.
(4) Tamping and/or vibrating to give thorough compaction; working between and around reinforcement.
(5) Laying on any type of sub-base preparing and leaving surfaces to receive screeds or paving.
Concrete in footpath and apron shall be treated as above ground level
Rates for mild steel or high tensile steel rod reinforcement shall be held to include for thoroughly wire
brushing and cleaning all bars free of rust, dust, mill scale, dirt, oil, any other deleterious matter, cutting to the
required lengths, bending and hooking and for securing with an including tying wires at all crossing, non-
designed spacers or chairs and distance blocks. No allowance shall be made for rolling margin in the
measurement of rod reinforcements.
SOR Premable Page 3
The conversion factor for the various steel reinforcement bars shall be as follows:
Rates for each item of fabric reinforcement shall be held to include for extra material at laps, tying wires and
all bending, cutting and notching around obstruction. Only the next area covered shall be measured and no
deduction shall be made for opening less than 1.00 square metre.
Rates for formwork shall be held to include for splayed edges, notchings, allowances for overlaps and
passing at angles, battens, strutting, bolting, welding, easing, wetting and treating with mould oil, striking and
removal. The rate in formwork allows for multiple uses where “multiple” means exceeding two.
Rates for concrete, reinforcement and formwork shall be applicable to all work irrespective of positions,
shapes and height
Rates for each item of precast concrete shall be held to include for all necessary mould, finished faces,
forming holes, rebates, sinking, mortices, recesses, hoisting and setting. The measurement of precast
concrete vents and grilles shall be held to include for all angles, intersections, ends outlets and extra labour
and material for forming grooves and rebates to sides. Piling work shall be executed in accordance with the
relevant specifications and Superintending Officer’s instructions.
Rates for each item of blockwork and facing shall be held to include for all special made blocks, bricks and in-
situ concrete in lieu, all holdfasts and bonding ties at abutments to concrete structures, all rough and fair
cuttings, over-sailing and receding courses, rough relieving and discharging arches, wedging and pining,
raking out joints for and pointing flashings, bedding plates, bedding and pointing of frames, parging and
coring flues, labour eaves filing, plumbing angles forming square and rebated reveals, cut squiats or
birdmouths, notches, forming, leaving or cutting chases, holes and morticles and cutting and pining and
making good and any other sundry items of a like nature.
Rates of blockwork and brickwork shall be applicable to all work irrespective of positions, shapes and height.
Deductions shall be measured the nett sizes of the openings and recesses, including the extra width or
rebated reveals. No deductions shall be made for voids not exceeding 0.10 square metre. Deductions shall
be made for strings, sills, lintols and the like only when exceeding 75mm in height.
Daywork
Should rates be applicable in respect of all work executed on a daywork basis. During the continuance of
such work, the Contractor shall keep proper records of the names, occupations and working hours of all
workmen employed for such work and the quantities and descriptions of all materials and plant employed.
Such records, receipts or vouchers must be verified by the Superintending Officer before payment can be
effected.
Rates for each item of pavior shall be held to include for all rounded-edges on in-situ paving, all arises and
making good and any other sundry items of a like nature.
Rates for each item for skirtings, risers, moulded edges, channels and the like shall be held to include for all
short lengths, formed, cut and purpose-made angle, junctions, end etc and making good and any other
sundry item of a like nature.
No deduction shall be made for a void of 0.50 square meter and under for in-situ paving.
In the case of construction of interlocking concrete paving blocks and footpaths, the composite rates shall be
applied, unless otherwise decided by the Superintending Officer.
(1) All laps, straight, skew and circular cutting at eaves, verges, top edges, abutments, valleys and hips,
cutting holes for pipes, nails, screws, clips, pellets, straps and the like.
(2) Chasing the structure for burning in or tucking in edges of coverings, flashing and the like.
(3) Holes in coverings, underbeds and insulations for pipes, standards and the like and making good.
No deduction shall be made for voids of 0.5m2 or less. Rates for Waterproofing Membranes and
Secondary Roofing System shall be held to include for narrow widths, small quantities, temporary
rules, covering up, protecting after laying and cleaning on completion, all labour to form arises, fair
edges etc., all cuttings and working around pipes, dress down at eaves to form drips or carried up
abutments to walls, pipes, parapets, skirtings, concrete curbs etc. and the like.
The description of each item of profiled sheet roofing or cladding shall be deemed to include all cutting
at square and raking abutments, top edges, bedding and pointing eaves fillers, verges, cutting, fitting
and making good around outlets, pipes and any other sundry items of a like nature.
SOR Premable Page 5
Rates for each item of carpenter and joiner shall be held to include for cutting, notching, boring, sinking,
pelleting, fitting, trimming, mitreing, halving, morticing, tenoning, devetailing, scarfing and wedging and for all
ends, splayed edges, short lengths, nails, screw and temporary supports and any other sundry item of a like
nature. Nominal sizes are stated for wrot timber and an allowance of 2.5mm is permitted for each wrot face.
Rate for windows and doors include handing and fixing.
Rates for each item of Ironmonger shall be held to include for supply, delivery to site and fixing complete with
all matching screws of the same finish as ironmongery, nails, pins or brads, cutting, sinking and boring and
morticing as required, oiling and easing and adjusting all moving parts, taking off and refixing after painting
where necessary. All references to trade names shall include those which are approved to those as specified.
Where ironmongery is included in the description of doors, it shall be deemed to include hinges, floor springs,
door gears, locks, latches, catches, bolts, closers, holders, padlocks, stoppers, push-bars and plates, pull
bars and handles, kick plates, locking eyes and the like as specified.
Rates for Carpenter, Joiner and Ironmonger items shall be deemed to include removal where necessary
unless otherwise stated, locks must include 2 keys properly labeled and handed to the Superintending
Officer.
Rates shall be held to include supply, delivery to site and fixing, cutting ends, welding, riveting, bolting etc. in
addition, the rates for structural steel is deemed to also include for hoisting, erecting, temporary bracing,
leveling and plumbing, and paint with one coat of primer.
No deduction shall be made for drilling, holes, notchings, splay cuts and the like.
Where no conversion table is available from manufacturer/supplier, specific gravity of 7.5 (i.e. 7.5OgmIcm3)
shall be used to compute the weight of mild steel sections.
Rates for each item of plastering shall be held to include for raking out joints, hacking to form keys, narrow
width and small quantities, temporary rules, joints between new and old plastering, internal angles, arises,
quirks, groin points and other intersections and curved surfaces, rounded coves and external angles not
exceeding 25mm radius, and mitres, tops, etc. om cornices, mouldings, enrichments, coves, skirtings, gutters
and strings, all making good and any other sundry item of a like nature.
In the measurement of plastering, no deduction shall be made for casings for pipes under 300mm wide or
angles which are finished in a different material if these do not exceed 100mm girth.
“Within the building” shall mean surfaces within the internal of buildings/flats, corridors, staircases and the
lilce which normally do not entail scaffolding or mechanical cradles to carry out the works.
“External face of building” shall mean surfaces such as gable end walls, front/back external walls and any
other surfaces which are constantly exposed to weather and/or normally require the use of scaffolding or
mechanical cradles to carry out the work.
SOR Premable Page 6
Rates for each item of wall tiling shall be held to include for narrow widths and small quantities and fittings
around air bricks, pipes and the like and any other sundry item.
Rates for each item of terrazzo shall be held to include for narrow widths and small quantities, and for all
temporary rules, internal angles, arises, joints between different types of terrazzo, quirks and making good
and any other sundry items of a like nature on in-situ terrazzo fitting around air bricks, pipes and the like and
any other sundry items of a like nature on precast terrazzo.
(3) The removal of debris from the site in the process of repair or as directed by the Superintending
Officer.
Rates for each item of glazier shall be held to include for cutting and rounded edges, puttying, fixing panel
pins, brass screws and cup and neoprene strips where necessary and leaving the glass clean on completion.
Rates for each item of painting shall be held to include for all necessary preparation of surfaces including
cleaning off, sandpapering woodwork, wire-brushing metal and leaving all surfaces free from dust, rust,
grease and oil before painting, narrow widths, etc.
Rates for painting include allowance for the use of different colours.
Rates for each item shall include cost of removal and cost of implementation of precautionary measures
where necessary unless otherwise stated.
SOR Premable Page 7
The following rates shall be applicable to all works executed on a daywork basis including shifting of office
equipment and furniture. During the continuance of such works, the Contractor shall keep proper records of
the names, occupations and working hours of all workmen employed for such work and the quantities and
descriptions of all materials and plant employed. Such records, receipts or vouchers must be verified by the
Superintending Officer before payment can be effected. Provided always that if the Superintending Officer
shall consider that for any reason the keeping of such records, receipts and vouchers by the Contractor as
required was impracticable, he shall nevertheless be entitled to authorize payment for such works either as
daywork (being satisfied as to the time employed and plant and materials used on such work) or at such
value thereof as he shall consider fair and reasonable.
Daywork’s Schedule of Rates for LABOUR and PLANTS items only (L00l to L034) is inclusive of 15%
Establishment Charge and Profit. The contract percentage adjustment shall also apply. For computation of
‘STAR’ rate using Daywork’s Schedule of Rates, the contract percentage adjustment shall NOT apply to the
‘STAR’ rates computation.
Rates for each item shall include cost of removal and implementation of precautionary measures where
necessary unless otherwise stated.
(a) The provision of all necessary tools equipment, labour, plant, machinery and
materials and mobilization from unit to unit and from block to block; the
emergency repairs to be executed immediately beyond the normal working hours
and may also beyond constraint boundary.
(d) Removal, cut off supply, diversion and reinstatement of water/electrical supply.
(e) The removal of debris from the site in the process of repair or as directed by the
Superintending Officer.
(h) Provision of props and formworks as directed by the Superintending Officer (for spalling concrete
works only).
2. The provision “per unit” refers to per unit of flat or shop or office, etc. If the work includes two toilets or
bathrooms in the same unit and the total area of work done does not exceed 3.5m2, then the Contractor
shall only be paid “per job”.
SOR Premable Page 8
3. The terms “per point” means each pipe surround that water leakage repair is carried out. If in a
bathroom, the leaking concrete surround the soil pipe, waste pipe and floor trap require repair, the
Contractor shall be paid three points.
Piling works shall be executed in accordance with the relevant specifications and the instruction of the
Superintending Officer.
(a) The removal of underground obstruction together with all work connection.
(b) The transportation, handling, pitching, heading, pointing, bracing and providing protective wrought
iron or helmet to pile.
(d) The cutting of surplus and heads of piles, extra excavation, backfilling and disposal of debris.
(e) The re-driving or intermittent driving necessitated by upheaving or lengthening of piles or by removal
of obstruction under piles or other causes including moving and repositioning the piling frame.
(f) The disposal of materials displaced arising out of driving the piles.
(g) The assembling of equipment on the site and the subsequent dismantling and removal shall be
given separately as an item.
(h) The movement of piling frames into position and about the site, any necessary excavation or filling
required placing the frames, raising or lowering the frames and any staging, barges or the like
required to support the frames.
Payment for treated timber piles driven shall be the product of the relevant rate per metre run and the
penetration depth (measured from tip to cut-off level).
Payment for each reinforced concrete piles after it is driven into the ground is measured from the cutoff level
of the pile to the end of pile shoe.
SOR Premable Page 9
Repairs to external finishes shall be executed in accordance with the relevant kinds described in the Contract
and shall confirm to the relevant Statutory Requirements and to be approved by the Superintending Officer.
Where trade names or manufacturer’s catalogue numbers are used, the reference is intended only as a guide
to the type of article or material. The Contractor may use any other article or material, subject to approval of
the Superintending Officer.
2 D-Pavior D095-Dl00
During the continuance of repair works, the Contractor shall keep proper records of the quantities (with
drawings, sketches, photographs, etc) and descriptions of all materials and plants employed. Such records
must be verified by the Superintending Officer before the Contractor is allowed to proceed with the painting
and touch up works.
TERM CONTRACT FOR BUILDING TRADESMEN WORKS
1 EXCAVATOR A1 – A2
2 CONCRETOR B1 – B12
4 PAVIOR D1 – D13
5 ROOFER E1 – E7
9 GLAZIER I1 – I2
10 PAINTER J1 – J7
12 DAYWORK L1 – L8
15 PILLING WORKS P1 – P2
A - EXCAVATOR
1 EXCAVATION A1
2 FILLING A1
SOR Page A1
EXCAVATOR
( To be read in conjunction with Preambles )
Excavation
A002 CART AWAY SURPLUS EXCAVATED MATERIAL off site and m3 12.80
deposit at the approved dumping ground.
A003 Excavate to pits, small holes etc not exceeding 0.10m3 to m3 4.70
receive base of posts, etc including removing surplus excavated
material off site and making good.
Filling
A004 Supply dry approved earth filling obtained from outside source No 6.00
and fill in layers of 300mm including labour for spreading,
trimming and consolidating to form earth moulds or levels.
A005 Supply coarse aggregate (19mm to 38mm gauge), spread and m3 10.50
level on site as directed.
m3 22.70
A011 Supply quarry waste/granite fines, spread, leveled, well rammed
B - CONCRETOR
1 Concrete Work B1
2 Reinforcement B2
3 Formwork B3
5 Miscellaneous B6
SOR Page B1
B002 Supply and cast Grade 15 mass concrete in foundation etc with 20mm to m3 169.30
10mm graded granite mechanically mixed including formwork and working
around rod or fabric reinforcement (reinforcement measured separately)*
Supply and cast reinforced concrete in foundations, ground beams, etc with
20mm to 10mm granite mechanically mixed, including formwork and working
around rod or fabric reinforcement below ground level (Reinforcement
measured separately) . *(B003 B007)
B013 Supply and cast concrete in SMALL quantities not exceeding 0.15 metre cube m3 328.00
to match existing, including all necessary formwork.
B014 Extra over Items B008 to B012 for trowelling concrete to footpath, apron etc. m2 0.70
B017 Supply high tensile steel rod reinforcement irrespective of size fabricated and kg 1.60
laid in position including labour for forming stirrups, links, etc irrespective of
size
* Supply and place BRC or other equal and approved welded steel FABRIC
REINFORCEMENT well lapped (minimum 1 square) and tied at joints
(measured nett) *(B0l8 B037)
B018 A5 m2 3.70
B019 A6 m2 4.80
B020 A7 m2 5.60
B021 A8 m2 7.00
B022 A9 m2 10.60
B024 B6 m2 7.30
B025 B7 m2 8.60
B026 B8 m2 10.20
B028 C6 m2 8.00
B029 C7 m2 10.20
B030 C8 m2 12.40
B031 D6 m2 8.00
B032 D7 m2 10.20
B033 D8 m2 12.40
B038 Supply and erect timber formwork to surfaces of concrete, columns, walls, m2 17.80
suspended slabs, stairs, canopies, beams, lintels, etc. (Measured net of
concrete surface)
B039 Extra over timber formwork for curve surface work. m2 3.50
Drain/Water Channel
B043 Construct 230mm wide (internal) reinforced concrete (Grade 25) surface m 84.20
drain with 100mm thick sides and base reinforced with a layer of BRC No,
36 wire mesh. All exposed sides, base and arises rendered smooth in
cement mortar (1:3) including all necessary excavation, hardcore, sand
blinding and formwork, laid to fall as directed for more than 600mm depth
to invert
B044 Extra over items for precast concrete channel to 230mm wide reinforced m 3.50
concrete surface drain.
B049 Extra Over for Precast Concrete channel to 305mm wide reinforced m 8.00
concrete surface drain.
B050 Extra over Items B040 to B042 and 3045 to B048 for forming 50mm x m 3.30
25mm rebate on both sides of channel for precast drain cover slab
(Measurement based on length of drain)
m3 77.10
B051 Break up concrete/surface drain including cutting reinforcement and
removing debris off site.
SOR Page B4
B053 Exceeding 300mm deep but not exceeding 450mm deep m 23.50
* Hack out existing concrete drain invert (Average Depth not exceeding
600mm) and regrade to fall towards outlet with cement
and sand (1:3) screed and finished smooth. *(B054 B055)
* Hack out existing carpark drain invert and regrade drain 450 to 600mm
width to fall towards outlet with cement and sand (1:3) screed and finished
smooth. *(3Q55 B057)
B061 Break up damaged/sunken 300mm closed conduit drain spun pipe include m 79.50
hacking through floor, excavation, planking, making good etc. and
reconstruct same jointed in cement mortar (1:3) to proper falls including
lean concrete base
* Supply and lay precast concrete composite channel laid to even falls
and jointed in cement and sand (1:3) mortar as detail drawing (EM-TC-
STD-BLDG-99-12) *(B062 B067)
Reconstruct existing scupper drain outside bin chute chamber with new
half round salt glazed stoneware pipes, side and base embedded in G20
concrete including adjusting existing gulley to match drain level bedded
and jointed with cement mortar (1:3).
B068 * Supply and lay half round salt glazed stoneware pipe in replacement m 23.90
jointed with cement and sand mortar (1:3) as scupper drain including lean
concrete base. *(3069 B070)
m 19.00
B069 100mm diameter
m 21.80
B070 150mm diameter
B07l Construct scupper drain not exceeding 150mm wide and 75mm deep on m 6.20
existing floor including trowelling surface smooth
B072 Regrade existing scupper drain with waterproofing cement and sand (1:3) m 5.00
screed laid to fall not exceeding 150mm wide and 75mm deep including
trowelling surface smooth
B073 Regrade existing scupper drain with waterproofing cement and sand (1:3) m 6.30
screed laid to fall exceeding 150mm but not exceeding 300mm wide,
75mm deep including trowelling surface smooth
B074 315mm diameter UPVC pipe conforming to SS272 for concealed drain m 58.50
outlet with Grade 30 concrete bed and reinforced with BE BRC including
formwork and lean concrete (excavation measured separately)
B095 Break up concrete, part re-use as hardcore, well rammed, leveled and m3 84.40
consolidated and surplus cart away off site, including cutting
reinforcement, if any.
B096 Cutting through reinforced concrete floors or walls (any thickness) to m3 390.40
form openings.
Bl00 Rake out existing damaged/worn out Bituminous Expansion Joint in m 3.80
concrete floors and refill same with approved hot bitumen.
B101 Supply and plug up bin chute wall holes with 300mm diameter detachable No 17.90
precast concrete complete with 13mm diameter mild steel handle
(exclude breaking existing concrete wall)
B102 Provide diamond saw—cutting to concrete floor to form 3mm width x m 2.00
40mm depth (mm) contraction joint.
Bl04 Provide diamond saw-cutting to apron slab/drain wall to form 50mm m 4.00
rebate for placing of precast concrete drain cover slab.
(Measurement based on rebate length)
B105 Provide 100mm wide Diamond Saw-Cutting” profile around concrete No. 15.50
electrode / lightning protection inspection pit inclusive of the removal of all
loosened concrete, casting of new Grade 25 concrete and the trowel
smooth all affected areas
B106 To provide 150mm long PVC weep hole pipes not exceeding 50mm dia No 3.60
through brick / concrete work not exceeding 100mm thick
B107 Raise or lower existing manhole cover and frame to match the existing No 17.80
level of path or paving
4 Miscellaneous C4 – C6
SOR Page C1
C003 Half brick thick reinforced with expanded metal brickwork reinforcement at m2 29.80
every 4th course.
C005 75mm thick BRICK-ON-EDGE reinforced with expanded metal brickwork m2 19.00
reinforcement at every course with 10mm joints raked
10mm deep or flush pointed as work proceeds
C006 Extra over common brickwork for forming fairfaced brickwall including m2 5.00
pointing in approved tinted cement mortar. (Applicable to C002 to CQO4)
One brick wall with facing bricks both sides, laid in compo mortar (1:3)
C007 with 10mm joints raked 10mm deep or flush pointed in approved tinted m2 80.00
cement mortar as work-proceeds
Half brick wall with facing bricks with expanded metal brickwork
C008 reinforcement at every 4th course laid in compo mortar (1:3) with 10mm m2 49.00
joints raked 10mm deep flush pointed in approved tinted cement mortar
as work proceeds
C011 100mm thick hollow block in compo mortar (1:3) and reinforced expanded m2 24.20
metal reinforcement in alternate course and blocks in each course filled in
solid with Grade 20 concrete
C013 90mm thick using M211 modular bricks size 190 x 90mm x 90mm m2 25.30
reinforced with expanded metal brickwork reinforcement at every four
course.
21
SOR Page C2
C014 90mm thick using M311 modular bricks size 290 x 90mm x 90mm m2 16.40
reinforced with expanded metal brickwork reinforcement at every fourth
course.
C015 Supply labour and materials to rake out mortar joints between standard m2 10.90
bricks and repointing with polymer modified cement mortar (based on
area of brickwall)
C016 Supply labour and matrials to rake out mortar joints between modular m2 9.50
bricks and repointing with polymer modified cement mortar (based on
area of brickwall)
EXTRA OVER standard common bricks (size 215 x 102.5 x 65mm) for the
following bricks
EXTRA OVER common modular bricks for using the following facing
bricks to one face of the brickwall (applicable to brickwall of thickness
190mm and above) *(C024 C030)
C033 Extra over half brickwall/solid block wall for the provision of HOT DIPPED m 5.40
GALVANISED BONDING BAR SYSTEM to the end
edges of brick wall/solid block wall as shown in drawing no.
EM-T0-STD-BLDG- 0402-0 B
C034 180mm to 195mm square glass block of 80mm to 100mm thick laid in m2 270.60
compo cement mortar (1:3) and pointed with approved tinted
cement mortar complete with panel reinforcing, panel anchors, expansion
strips, etc. according to manufacturer’s instructions
C035 “NEG” or other approved Glass block wall consists of 145 x 145 square m2 284.30
glass block of 80 to 100mm thick glass laid in compo cement mortar (1:3)
and pointed with approved tinted cement mortar complete
with panel reinforcing, panel anchors, expansion strips, etc. according to
manufacturer’ s instructions
C036 Supply labour and material to rake out broken/damaged glass blocks of No 13.60
any size and replace with new glass block to match existing (for remedial
work not exceeding 10 nos. glass blocks)
C037 Rake out joints to an even depth of 25mm to 30mm. Brush out all loose m 8.20
materials and fill the groove solid with approved polyurethane sealant/
polysuiphide sealant in accordance with manufacturer’s instruction to form
a continuous sealant (Gondola measured separately)
C038 Extra over item for filling the groove/ expansion joint solid with an m 1.40
approved backing rod.
C039 Supply labour and materials to form splay with approved polymer modified m 5.00
cement mortor/non shrink grout to the correct gradient including hacking
when necessary
C040 Repair the brick/tiled wall panels by washing, patching cracks and m2 10.40
applying 1 coat of approved adhesion promoter and 2 coats of approved
elastorneric waterproofing coating according to manufacturer’s
instructions
SOR Page C4
C042 Repair the reinforced concrete/plastering finished wall panels by washing, m2 9.00
patching cracks and applying 1 coat of approved adhesion promotor and
2 coats of approved elastomeric waterproofing
coating according to manufacturer’s instructions
C045 Repair the patch joints between precast sills by mortar joint and approved No. 1.60
polyurethane sealant according to manufacturer’ s instructions
Apply approved silicon sealant to joints, pointings, grooves, etc. according m 1.70
C047 to manufacturer’ s instructions
Repair to reinforced concrete beam cracks by hacking out existing crack m 6.40
C048 and patch it with 1:3 cement and sand mortar gauged
with approved synthetic latex or other approved additive including painting
2 coats of emulsion paint to the repaired surface.
Miscellaneous
C049 Labour and material for pointing joints of brickworks in coloured cement. m2 4.20
C050 Labour for raking out joints of existing brickwork, clean, re-jointing with m2 5.90
cement mortar and re-pointing with a flush joint.
C052 Cutting out existing block or brick work to form chase etc not exceeding m 7.30
300mm girth
C053 Cutting out block or brickwork to form chase exceeding 300mm but not m 9.90
exceeding 600mm girth
m3 101.70
C054 Cutting out block or brickwork to form opening
Lay approved damp proof course well lapped at joints and bedded in m2 8.90
C055
cement mortar (1:3) according to manufacturer’s instructions
SOR Page C5
C056 Supply and lay approved horizontal damp proof course complied with BS m2 8.90
6398 Type B (felt fibre base) to brick/block walls bedded in prepacked
mortar as specified
C057 Hack out cracks of brick or block walls to form ‘V’ shaped grooves m 4.00
approximately 25mm wide x 20mm deep and seal up with polymer
modified mortar and painting surfaces to match existing.
C059 Repair to cracks by hacking RUT’ groove on the cracks to 25mm width x m 6.50
20mm depth. Brush out all loose sand and mortar and
fill the groove with polymer modified mortar including painting to the
repaired surface.
C060 Repair to cracks by hacking V grooves on the cracks and patch with m 19.40
approved polysulphide sealant including painting to the repaired surface
C06l Supply labour and materials to repair the defective plaster by touching up m2 26.40
defective concrete substrate with polymer modified mortar and skimming
to average 6mm thick approved materials including
hacking, applying bonding agent and painting and all as specified
C062 Supply labour and materials to repair the plastered wall panels by m2 13.50
applying two coats of approved prepacked skim coat including hacking,
painting to the repaired surface
C063 Supply labour and materials to repair defective plaster with average m2 20.70
18mm thick prepacked mortar including hacking, apply bonding agent and
painting and all as specified
C064 Supply labour and materials to repair the defective plaster with average m2 44.10
18mm thick polymer modified mortar including hacking, apply bonding
agent and painting and all as specified
C065 Installation of special wall tie to existing brickwall including galvanised no 8.10
mesh sleeve, approved resin, stainless steel wall tie
C066 Form nib with non shrink grout including Chemical Capsule @ 300mm m3 3,835.10
centre to centre, necessary reinforcement, formwork,
skimming coat and painting
SOR Page C6
C068 Watertightness test to external wall by spraying water at 300 litre/hour hr 9.70
(Gondola measured separately)
C069 Watertightness test to external wall by spraying water at 600 litres/hour as hr 10.50
specified (gondola measured separately and water provided by PA
without charges)
C070 Watertightness test to exteria1 wall by spraying water at 300 litre/hour hr 7.50
using perforated PVC pipe
C07l Watertightness test to external wall by spraying water at 600 litre/hour hr 8.20
using perforated PVC pipe
C072 Hammer dressed random rubber in granite laid in prepacked mortar and m3 222.70
pointed in coloured cement
C073 13mm deep polyurethane sealant joint (horizontal or vertical) with 10mm m 4.20
diameter backer rod to fill gap between brickwall
and beam/column as specified
C074 Supply and fix 100mm x 80mm x 6mm thick galvanised angle plate with m 50.80
approved 8mm diameter chemical adhesive galvanised stud
archor @ 150 c/c to existing wall
C075 Supply labour and materials to rack out mortar joint at the interface to a m 4.20
depth of 25mm. Brush out all loose sand and mortar and fill the groove
with polymer modified mortar
C076 Supply labour and materials to repair insitu-laid external tiles with G25 m2 23.40
concrete screed and colour elastomeric membrane including hacking and
all as specified
C077 Supply labour and materials to repair insitu-laid external tiles with m2 21.60
approved prepacked skimming materials and colour elastomeric
membrane including hacking and all as specified
C078 Supply labour and materials to rake out existing mortar joint, brush out all m 7.60
loose materials, fill the joint with approved backing rod, follow up with
approved non- shrink grout in accordance with the manufacturer’ s
instructions
C079 Strengthening of existing brickwalls, tile cladding, etc with ‘Hilti’ HRD wall No 7.70
tie including drilling holes, brush out all loose materials, fill hole with non-
shrink grout and touch up hole with paint to match existing
D – PAVIOR
S/N Contents SOR Page
1 Cement and Sand Rendering D1
2 Granolithic Paving D2
4 Cast-in-Situ Terrazzo D3
5 Mosaic Tiling D2 – D3
6 Brick Paving D3
8 Slate Tiling D5
9 Quarry Tiling D5
14 Concrete Topping D8
15 Vinyl Tiling D8
17 Dividing Strips D8
21 Miscellaneous D8 – 9
PAVIOR
(To be read in conjunction with Preamble)
D001 For every 5mm thick exceeding 20mm thick up to a maximum of 60mm m2 1.40
thick.
* 20mm thick cement and sand (1:3) to form skirtings, treads, risers, curbs
and return etc including coved and rounded angles for
*(D003 DOOS)
* 20mm thick cement and sand (1:3) to upper floor trowelled to a smooth
finish
*(D006 D007)
D007 For every 5mm thick exceeding 20mm thick up to a maximum of 60mm m2 1.75
thick.
* 20mm thick cement and sand (1:3) skirtings, treads, risers, curbs and
return etc including coved and rounded angles for *(D008 D010)
D012 Extra over for using hardener or other approved non-metallic hardener m2 1.50
mixed according to manufacturer’s instruction for each 5mm thickness
(applicable to other pavior items)
D013 Extra over 3mm thick coloured cement topping finish of terracotta, white, m2 9.60
red and green colour, surface floated smooth with a steel trowel
SOR Page D2
D015 For every 5mm thick exceeding 20mm thick up to a maximum of 60mm m2 1.20
thick
* 20mm thick Granolithic skirting, treads, risers, curbs and returns etc
including coved and rounded angles for *(D0l6 D017)
D019 20mm thick single coloured cement paving to floor laid in panels on and m2 21.30
including minimum 10mm thick cement and sand (1:3) base screed.
D020 20mm thick multi-coloured cement paving to floor laid in panels including
minimum 10mm thick cement and sand (1:3) base screed m2 26.70
Cast-in-situ terrazzo
D021 20mm thick terrazzo finish to floor laid in sections, on and including m2 43.70
minimum 20mm thick cement and sand (1:3) base screed, polishing to
approval
* 20mm thick terrazzo skirtings, treads, risers, curbs and returns etc
including coved and rounded angles polishing to approval *(D022 D023)
Mosaic Tiling
* Semi-glazed mosaic tiles of approved colour and pattern to floor laid and
jointed in cement grout on and including minimum 13mm thick cement and
sand (1:3) base screed and pointed in cement
* (D024 D026)
D025 Not exceeding 150mm girth to skirtings, treads, risers, curbs and returns m 10.20
etc with all necessary coved and rounded angles
D026 Exceeding 150 but not exceeding 300mm girth to skirtings, treads, risers, m 18.20
curbs and returns etc with all necessary coved and rounded angles
SOR Page D3
D028 Not exceeding 150mm girth to skirtings, treads, risers, curbs and returns m 9.40
etc. with all necessary coved and rounded angles
D029 Exceeding 150 but not exceeding 300mm girth to skirtings, treads, risers, m 16.50
curbs and returns etc with all necessary coved and rounded angles
Brick Paving
D030 Hack off existing damaged brick-on-edge on steps, coping, footpath m2 5.20
D031 Supply and lay new brick on edge in cement mortar (1:3) to existing steps, m2 58.30
coping, footpath, etc, including proper surface preparation pointing with
cement mortar
D032 Brick-on-edge paving in facing brick laid to approved pattern and bedded m2 50.10
on and including minimum 13mm thick cement and sand (1:3) screed and
pointed in cement mortar.
D033 Brick-on-edge paving in single bull-nose one brick width laid and bedded on m 17.60
and including minimum 13mm thick cement and sand (1:3) screed and
pointed in cement mortar.
D034 Brick on edge paving in double bull-nose one brick width laid and bedded m 22.00
on and including 13mm cement and sand (1:3) screed and pointed in
cement mortar.
D035 Supply and lay brick-on-edge at (minimum 60° inclination from ground m 19.40
level) single bull-nose brickwork in compo mortar with bedding and 10mm
joints including excavation and leveling from site and leveling
D036 Brick tiles laid to approved pattern jointed, pointed and bedded on and m2 44.60
including 13mm thick cement and sand (1:3) screed.
D037 Supply and lay any size, minimum 8mm thick heavy duty homogeneous m2 58.60
polished floor tile of approved colour and pattern, jointed, pointed and
bedded on and including minimum 20mm thick cement and sand screed
(1:3)
* Supply and lay to skirtings, treads, risers, curbs, nosings and returns, any
size, minimum 8mm thick heavy duty homogeneous polished tile of
approved colour and pattern, jointed, pointed and bedded on and including
minimum 20mm cement and sand screed (1:3) *(D038 D040)
D042 Exceeding 0.lm2 but not exceeding 0.3m2(for single patch) No. 19.00
D043 Exceeding 0.3m2 but not exceeding 0.5m2 (for single patch) No. 29.50
D044 Exceeding 0.5m2 but not exceeding lm2 (for single patch) No. 59.00
D045 Supply and lay any size, minimum 8mm thick, heavy duty homogeneous m2 39.00
unpolished floor tile of approved colour and pattern, jointed, pointed and
bedded on and including minimum 20mm thick cement and sand screed
(1:3)
* Supply and lay to skirtings, treads, risers, curbs, nosings and returns, any
size, minimum 8mm thick, heavy duty homogeneous unpolished tile of
approved colour pattern, jointed, pointed and bedded on including minimum
20mm cement and sand screed (1:3) *(D046 D048)
* Supply and lay any size, minimum 8mm thk heavy duty homogeneous
unpolished floor tiles of approved colour and pattern, jointed and pointed
with approved grout (1:3) *(D049 D052)
No. 6.50
D049 Not exceeding 0.lm2 (for single patch)
No. 17.00
D050 Exceeding 0.lm2 but not exceeding 0.3m2(for single patch)
D051 Exceeding 0.3m2 but not exceeding 0.5m2(for single patch) No. 27.00
D060 Not exceeding 150mm girth to skirtings, treads, risers, curbs, nosing and m 6.50
returns.
D061 Exceeding 150mm but not exceeding 300mm girth to skirtings, treads, m 11.90
risers, curbs, nosing and returns.
D062 Exceeding 300mm but not exceeding 450mm girth to skirtings, treads, m 19.60
risers, curbs, nosing and returns.
* Quarry / Klinker tiles of the following size laid and bedded on and
including minimum 20mm thick cement and sand screed (1:3) *(0063 0066)
D066 Not exceeding 150mm girth to skirting, treads risers, curbs, nosing and m 4.80
returns.
* Supply and lay quarry / klinker tiles of approved colour and pattern,
jointed, pointed and bedded on and including minimum 20mm thick cement
and sand screed (1:3) *(0067 0070)
D068 Exceeding 0.1m2 but not exceeding 0,3m2 (for single patch) No. 13.10
D069 Exceeding 0.3m2 but not exceeding 0.5m2(for single patch) No. 18.90
D070 Exceeding 0.5m2 but not exceeding 1.0 m2 (for single patch) No. 37.90
* Supply and lay teak parquet floor tile to match existing inclusive of
approved adhesive and sanding down *(D07l 0073)
D074 Scrape off existing damaged parquet floor tile and remove all adhesive m2 5.10
stains
SOR Page 6
* Supply and lay interlocking concrete paving blocks (any colours and
patterns) to footpath/concourse to match existing including compacting
ground with additional sand bed to required level. *(D075 D076)
* Supply and lay interlocking concrete paving blocks (any colours and
patterns) to new footpath including compacting with 40mm thk (mm) sand
bed (Excavation and hardcore measured separately) *(0077 D079)
D080 Supply and lay 60mm thick interlocking brick paving blocks to m2 30.80
footpath/concourse to match existing damaged blocks, compacting and
laying additional sand-bed to required level
D081 Supply and lay 60mm thick interlocking brick paving blocks to new footpath/ m2 27.80
concourse including compacting with 40mm thk (mm) sand bed (Excavation
& hardcore measured separately)
D082 Construct 100 x 200mm depth side kerb with grade 25 concrete including m 5.20
all necessary formwork
D083 Labour for taking out loosen sunken, interlocking concrete/brick paving m2 9.20
block and relay paving blocks including compacting ground with additional
hardcore and to required level and filling of voids
* Supply and lay interlocking concrete paving blocks (any colour and
patterns) to new footpath, concourse area, etc including excavation of site
on ordinary ground, backfilling, forming of surfaces and edges making
good, removal of surplus excavated material off site to approval dumping
ground, 150mm thick hardcore including 25mm thick sand binding,
compaction of ground, compacting with minimum 40mm thick sand bed
D087 Supply and lay “Superkote” or other approved high strength polymer m2 23.00
coating imprint to floor according to manufacturer’ s instruction
D088 Supply and lay imprint surface in any colour to floor with 20mm thick m2 32.00
cement and sand screed according to manufacturer’s instruction
D089 Supply and lay 20mm thick concrete paving to floor imprint with recessed m2 30.20
pattern, approved colour and varnish to match existing floor
D090 Supply and lay 50mm thick concrete stamping finish in patterns to floor m2 34.20
according to manufacturer’s instruction(concrete base measured
separately)
D091 Supply and lay 15mm thick pebble wash/ coloured granolithic finish to floor, m2 34.50
laid in section
D092 Supply and lay border 100 to 150mm girth with pebble washed/coloured m 7.30
granolithic finish of 15mm thick
D093 Supply and lay border 150 to 300mm girth with pebble washed/colour m 12.30
granolithic finish of 15mm thick
D094 Extra over for every 5mm thick for Item D091 to D093 m2 8.30
Concrete Topping
D096 For every 5mm thick exceeding 20mm thick up to a maximum of 60mm m2 1.55
thick
D099 ADD to (or deduct from) Item 0097 for each 5mm thickness over (or under) m 0.90
25mm
D100 ADD to (or deduct from) Item 0098 for each 5mm thickness over (or under) m 1.25
25mm Grade 40 structural concrete with 10mm maximum size aggregate
topping including working around rod or fabric reinforcement (reinforcement
measured separately) and trowelled to smooth surface with powerfloat as
specified. *(D10l D102)
D102 For every 5mm thick exceeding 25mm thick up to a maximum of 60mm m2 1.80
thick
SOR Page 8
D103 Supply and lay 2mm thick vinyl floor tile to match existing inclusive of m2 18.30
approved adhesive (Removal measured separately)
Self-levelling Screeding
D104 Supply and lay self-levelling topping screed minimum 6mm thick m2 17.50
(cementitious based) flooring with bonding agent and rubber strip
expansion joint to fall with minimum 6mm thickness complete with one layer
of sealer coat to manufacturer’s
instruction
Dividing Strips
D105 Mosaic tiles to form court line(38mm to 50mm wide) for badminton, sepak m 4.70
takraw and basketball courts etc.
m 6.90
D106 25mm x 3mm aluminium dividing strips
m 8.10
D107 25mm x 3mm copper dividing strips
m 9.70
D108 25mm x 3mm stainless steel dividing strips
m 2.40
D109 PVC’L’ shaped strips
D110 Supply and apply epoxy mortar screed flooring system with epoxy resin m2 41.00
primer follow by a layer of minimum 5mm thick epoxy mortar and a non-slip
sealer coat after 24 hours curing
D111 Supply and lay one coat of finishing grout colour (sundek or other m2 16.30
approved) to match existing complete with one coat of acrylic clear top coat
for repair to colour screed surface
D112 Supply and lay solhofen natural stones of approved pattern, jointed, pointed m2 44.90
and bedded on minimum 20mm thick cement and sand screed (13)
Miscellaneous
* Hack off all existing damaged rendering /finishings on floors, treads, risers
etc and prepare surface to receive new finish *(D113 D115)
D116 Hack existing floor to form random keys, clean and wash to receive new m2 1.30
finish
D117 Scrape off existing damaged vinyl tile / carpet / linoleum and remove all m2 1.80
adhesive stains
SOR Page 9
D122 Patch up existing holes to floor rendering not exceeding 0.1 metre square in No. 2.10
cement mortar (1:3) gauged with bonding agent top surface trowelled
smooth to match existing.
D123
Patch up existing damaged mosaic floor finishings with new mosaic to No 6.70
match existing for single patch not exceeding 0.1 metre square
D124
Re-pointing joints of existing mosaic floor in white cement including m2 4.60
cleaning floor on completion.
Concrete base to tube stand of fixed table/stool in hawker centres not No 15.00
exceeding 200mm diameter and 75mm high including mosaic/ceramic tiles,
coved tiles, to match existing
D128 * Supply and lay approved two components patching compound mixed with
liquid acrylic based additive according to manufacturer’ s instruction
D129
To floor of 4-5mm thickness m2 16.30
To cracks in walls, slabs, soffits and floors approximately 25mm x 25mm m 5.30
deep including forming ‘V’ shaped grooves Supply and lay approved single
component consists of special cement and synthetic
aggregates according to manufacturer’s instruction
D130
To floor of 4-5mm thickness m2 16.30
D131
To cracks in walls, slabs, soffits and floors approximately 25mm x 25mm m 5.30
deep including forming ‘V’ shaped grooves Supply and lay approved two
components mortar based compound consists of cement, additivies,
aggregates and well-graded
filler mixed with liquid acrylic polymer and synthetic resin according to
manufacturer’ s instruction
To cracks in walls, slabs, soffits and floors approximately 25mm x 25mm m 6.60
deep including forming ‘V’ shaped grooves
E – NOT IN USE
F – CARPENTER, JOINER AND IRONMONGER
1 False Ceiling F1
2 Fire-Rated Doors F2
3 Doors F2 – F5
4 Windows F5
5 Boarding F5
6 Fire-Rated Partitions F6
7 Bolts F7
8 Hinges F8
10 Locking Eye/Ear F8
11 Door Holder/Closer F8
12 Keys F9
17 Lockset F13
27 Chicks/Blinds F16
31 Miscellaneous
SOR Page F1
False Ceiling
F001 Supply and fix symmetrically 6mm thick asbestos-free cement board ceiling m2 16.00
lining including all necessary timber cover fillets
F006 Supply and fix 12mm thick soft board as ceiling or wall panel (timber m2 11.80
framing and fillets measured separately)
F007 Supply and fix 12mm thick mineral fibre or plasterglass ceiling boards in-fill m2 25.60
including “L11 shape aluminium stiffener, where necessary
* Supply and fix fibre plastered board to lobby ceiling on timber framing
support x 50mm treated timber and 50 x 25mm hanger treated timber
*(F008 F009)
m2 27.00
F008 9mm thick
m2 33.00
F009 12mm thick
* Supply and fix gysum ceiling board including all necessary joint (tanalised
timber frame and painting measured separately) *(F010 F011)
F012 Supply and fix plasterglass / gypsum cornices including all necessary joint m 8.20
and removal of old cornices.
F013 Supply and fix “TTT or “L” shaped galvanised steel strips with aluminium or m 4.00
enamel finishes not exceeding 30mm wide as fillet for false ceilings
including hanging wires or adjustable rod hanger.
F014 Supply and fix 9mm thick egg crate plastic louvre for encasing gas pipe m2 24.40
SOR Page F2
F015 Supply and fix a complete system of 45mm thick single leaf half-hour fire m2 239.50
rated timber surface finished composite door and all necessary
ironmongery and accessories as specified and approved by PSB and FSB
F016 Supply and fix a complete system of 45mm thick single-leaf half-hour fire m2 264.50
rated timber surface finished composite door complete with 6mm thick
wired clear glass observation panel, and all
necessary ironmongery and accessories as specified and approved by PSB
and FSB
F017 Supply and fix a complete system of 45mm thick half-hour fire rated m2 345.00
aluminium clad composite door for Service Duct complete with aluminium
clad timber door frames and ironmongery as specified
in detailed drawing (EM-TC-STD-BLDG-99-13) and approved by PSE and
FSB
F018 Supply and fix a complete system of 45mm thick half-hour fire rated m2 304.80
aluminium clad composite door in two leaves for Store, Bulk Refuse Area,
CD Shelter or Switch/Pump/MDF Room complete with
aluminium clad timber door frames and ironmongery as specified in detailed
drawing (EM-TC-STD-BLDG-99-13) approved by PSB and FSB
Doors
F019 Supply and install 38mm thk Framed, Ledged and Braced Door and filled in m2 92.00
with 19mm thick tongued and grooved “V” jointed boarding as specified in
drawing(EM-TC-STD-BLDG-99-14)
F020 Supply and install 45mm thk Framed, Ledged and Braced Door and filled in m2
with 19mm thick tongued and grooved “V” jointed boarding \ 101.20
P021 Supply and install 50mm thk Framed, Ledged and Braced Door and filled in m2 112.70
with 25mm thick tongued and grooved “V” jointed boarding
* Supply and install in the following thickness with framings slot & fix and
filled in with 13mm thick timber louvres including fixing fillets *(F022 F023)
F024 Supply and install 38mm thick flush door filled in on both sides with 6mm m2 68.10
thick plywood as per drawing no. (EM-TC-STD-BLDG-99--28)
* Supply and install solid cored flushed door filled in on both sides with
6mm thick plywood *(F025 P027)
Supply and install 40-45mm thick half-round fire-rated single leaf decorative no. 325.80
solid timber composite door for main entrance(door frame and stain
F029 vanished not included) complete with ironmongery approved by PSB and
FSB (for door-size ranging from 850-1000mm in wide and 2100-2200mm in
height)
F030 Supply and install 38mm thk switchroom door with 2 or 3 panels filled in m2 70.00
with 9.5mm thick plywood and 1 panel with framing slot & fix and filled in
with 13mm thick timber louvres including fixing fillets
* Supply and install panel door in the following thickness in 4 panels filled in
with 9.5mm thick plywood *(F031 F033)
* Supply and install framed cupboard door in the following thickness filled in
with 6mm thick plywood *(F034 F036)
m2 31.50
F034 19mm thick
m2 33.30
F035 25mm thick
m2 35.30
F036 32mm thick
F037 Take down part decayed timber doors take out decayed members and m2 17.00
incorporate new members, adjust and re-assemble door including all
necessary dowels and wedges and re-fixing doors to position and removal
of debris from site (New timber members measured separately)
F038 Take down warped doors, ease, adjust and refix to position m2 4.30
F039 Cut into/take out part (not whole piece of timber member) / rotten or
decayed frames, mullion, transome, cills, handrails, etc and form all m 8.00
necessary approved joints to receive new timber including taking down of
doors, if necessary and rehanging in position new timber measured
separately)
F040 Bore holes to door panels not exceeding 25mm diameter for ventilation No. 0.60
F041 Pull off existing nails, hooks, screws etc. from timber and fill up holes with No. 0.40
wood putty or other approved material and touch up with paint to match
existing
F042 Fill up door lock holes, hinge rebates, etc with and including adhesive and No. 2.70
timber, sand-papering and knotting, and painting to match existing
F048 Supply and install 10mm thick twin-wall tinted bronzed polycarbonate sheet m2 93.00
onto existing frames with aluminium champing bar c/w snap on cover and
all necessary accessories
F049 Supply and install 12mm thick tempered glass swing door lm x 2.lm c/w m2 847.80
ironmongery, handle including all necessary fixing, jointing and accessories
F050 Supply and install 12mm thick tempered glass for door and full height glass m2 192.20
partition
F051 Supply and install 12mm thick glass for door and full height glass partition m2 228.30
F052 Labour to take down tempered glass door to clean, oil all mechanism and m2 11.20
refix in position with proper alignment
F053 Labour for checking and repair auto sliding door (cost of parts shall be paid no. 207.00
separately)
F054 Supply and fix wide angle door viewer no. 7.30
F056 Supply and fix stainless steel security door chain and slot no. 10.80
F057 Supply and fix chrome security door chain and slot no. 8.50
WINDOWS
F066 Supply and fix back vinyl gester sealing strips to perimeter of window frame m 2.10
with holding down screws or nails at 50mm centre
Supply and install 38mm thick windows with framings stop slotted and filled
F067 in with 13mm thick timber louvres including fixing fillets m2 75.00
Supply and install 38mm thick framed windows open rebated and prepared
for glass including fixing beadings (glass measured separately)
F068 m2 56.10
Take down part decayed timber windows take out decayed members and
incorporate new members, adjust and re-assemble windows including all
necessary dowels and wedges and re-fixing windows
F069 to position and removal of debris from site (New timber members measured m2 17.00
separately)
F070 Take down warped windows, ease, adjust and refix to position m2 8.10
F071 Cut into/take out part (not whole piece of timber member), rotten or m 8.00
decayed frames, mullion, transome, cills, handrails, etc and form all
necessary approved joints to receive new timber including taking down of
windows, if necessary and rehanging in position new timber measured
separately)
F072 Supply and fix rubber glazing gasket to Notice Board, sliding windows, top m 3.80
hung and casement windows
F073 Supply and fix 300mm long chromium plate casement studs no. 5.60
F074 Supply and fix black Japenned casement studs no. 1.80
F075 Supply and fix chromium plated casement fasteners no. 4.50
Boarding
Wrot kapor boarding to floors, shelves, fitments, partitions, ceiling, etc. well
cramped up, nailed or screwed to bearers (Bearers measured separately)
*(F076 F079)
F080 Supply and install one-hour fire rated partitions both sides covered with m2 30.80
approved 15mm thick gypsum boards constructed with ‘U’ channel frame
including all accessories & necessary works (dismantling of existing false
ceiling, partitions, diversion of services, painting and other finishes
measured separately)
F081 Supply and install half-hour fire rated partitions both sides covered with m2 25.20
approved 12mm thick gypsum boards constructed with ‘U’ channel frame
including all accessories & necessary works (dismantling of existing false
ceiling, partitions, diversion of services, painting and other finishes
measured separately)
F082 Supply and fix in replacement approved 15mm thick gypsum board to m2 11.70
existing fire rated partitions including dismantling of existing false ceiling
and re-fix in position, if applicable. Remove debris and make good work -
disturbed (diversion of services, painting and other finishes measured
separately)
F083 Supply and install 50mm thick half-hour rated solid kapor timber door m2 97.20
constructed with T & G boardings and flush jointed with 3 nos. of 10mm
diameter mild steel tie rods including wired glass peephole (painting and
ironmongery measured separately)
Bolts
F100 90mm x 27mm stainless steel barrel/square shoot bolt No. 7.70
F101 240mm x 27mm stainless steel barrel/square shoot bolt No. 9.00
F103 150mm x 25mm stainless steel flush shoot bolt No. 9.30
F104 225mm x 25mm stainelss steel flush shoot bolt No. 9.90
* Supply and fix HEAVY DUTY HOOK AND BAND HINGES to bin
compound door
* (F116 F117)
F118 Supply and fix heavy duty galvanised hasp and staple for roof trap door No. 9.50
F119 Supply and fix 50mm long aluminium or galvanised mild steel hasp and No. 1.60
staple for notice board or other uses
F120 Supply and fix 75mm long aluminium or galvanised mild steel hasp and No. 1.50
staple for notice board or other uses
Locking Eye/Ear
F121 Supply and fix 12/25mm diameter galvanised steel diameter locking eye to No. 1.60
pad bolts
Fl22 Supply and fix 100mm x 60mm x 3mm stainless steel plate as locking ear No. 8.80
to switch room, pump room etc.
F123 Supply and fix 75 x 38 x 3mm stainless steel plate as locking eye to No. 8.30
switchroom, pumproom, etc.
Door Holder/Closer
F124 Supply and fix spherical magnetic door holder No. 6.00
F125 Supply and fix 38mm diameter rubber door stop No. 1.40
F126 Supply and fix of “Yale” Model lite 2 auto-retractable hydraulic door closer No. 33.70
including refixing, adjusting to position
F127 Supply and fix “Union” Model 8573/8173 door closer including refixing, No. 62.90
adjusting to position
F128 Supply and fix door closer “Dorma TS 73” No. 139.40
F129 Supply and fix door closer “Dorma TS 73V/BC No. 155.20
F130 Supply and fix door “Dorma ETS 8411 non-hold floor spring c/w door strap No. 327.60
including alignment of glass door
SOR Page F9
F133 Supply and cut one key to lock with missing keys including taking out lock, No. 9.70
where necessary and refix same
F134 Open door to gain access into premises where keys have been lost Door 7.40
F135 Provide locksmith for gaining access to premises without damaging the lock Door 50.00
Door Handles
F136 Supply and fix YTL-75 or other approved stainless steel cup handle for No. 12.90
pumproom, switchroom, service duct door, etc.
F137 Supply and fix YTL-85 or other approved stainless steel cup handle No. 34.80
passage latch for service duct door with cup handles on both sides
F138 Supply and fix “U-shaped” stainless steel handle (225 x 57 x 19mm) to door No. 31.20
F139 Supply and fix stainless steel push plate (150 x 300 x 1.5mm thick) to door No. 29.00
F141 Supply and fix 100 x 50mm aluminium flush pull No. 4.00
F142 Supply and fix 150mm aluminium handle fleet “Delta 2553” No. 7.10
F144 Supply and fix “Delta” stainless steel handle No. 32.80
F145 Supply and fix 100mm stainless steel bow handle No. 5.10
Anchors
F147 8mm diameter x 110mm long galvanised steel anchor inclusive of adhesive No. 8.10
cartridge
F148 10mm diameter x 130mm long galvanised steel anchor inclusive of No. 9.50
adhesive cartridge
F149 12mm diameter x 160mm long galvanised steel anchor inclusive of No. 10.90
adhesive cartridge
F150 16mm diameter x 190mm long galvanised steel anchor inclusive of No. 14.70
adhesive cartridge
SOR Page F10
F152 10mm diameter x 130mm long stainless steel anchor inclusive of adhesive No. 16.30
cartridge
F153 12mm diameter x 160mm long stainless steel anchor inclusive of adhesive No. 19.20
cartridge
F154 16mm diameter x 190mm long stainless steel anchor inclusive of adhesive No. 30.20
cartridge
* 5mm thick stainless steel eye anchor of internal diameter 15mm of Grade
AISI 304 complete with stainless steel spacer *(F155 F157)
F156 Supply and fix eye-anchor as specified including drilling of holes, epoxy No. 7.40
putty and approved nylon plug
F157 Supply and fix eye-anchor as specified including epoxy putty and approved No 6.30
nylon plug but exclude drilling of holes
Padlocks
* Supply only “Yale’ brass cylinder padlock complete with 2 keys *(F161
Fl65)
* Supply and deliver padlock with key alike system (I key for every 5 nos. of
lock) *(F166 F175)
F176 Supply 300mm long chain/ring fixed to metal box, door etc for padlock No. 2.70
Locksets
F177 Supply and fix cam lock (Yale Model No. 490.25) for letter box or other No. 13.30
uses including spot weld the locking nut, where necessary
F178 Supply and fix approved master lock to door behind letter boxes No. 14.20
F179 Supply and fix lock for notice board No. 12.50
F180 Supply and fix Yale” 513/ 32626 single cylinder mortice dead lock No. 60.40
F181 Supply and fix cylinder rim drawback locks (‘Union” 1332-SE, “Yale” No. 1 No. 49.90
or other approved) complete with 3 keys
F182 Supply and fix cylinder mortice lockset complete with stainless steel handle No. 64.80
(“Union” 643/46/41, “Showa” CL-05-240 or other approved)
F183 Supply and fix double cylinder mortice lockset. with stainless steel handle No. 70.60
(“Union” 643/46/241, “Showa” CL-26-240 or 6ther approved)
F184 Supply and fix brass cupboard or drawer locks of approved quality No. 9.90
F185 Supply and fix sashlock to aluminium sliding window No. 13.10
F186 Supply and fix aluminium or zinc die cast crescent lock to aluminium sliding No. 4.40
window
F187 Supply and fix single cylinder mortice lock “Union” 2441, “Yale” 514/32626 No. 63.70
or other approved to aluminium sliding door
F188 Supply approved dial face number combination lock No. 10.40
F189 Supply and fix lockset to aluminium sliding door (“Alboy 2260” or other No. 121.60
approved)
F190 Supply and fix “Union” 8098 or other approved indicating bolt for toilet door No. 13.70
SOR Page F12
F191 Accord 2332/1405 under MK and master key series MK48 No. 68.40
F192 Forte H6RP75ES under PA master key series MK48 No. 61.70
Fl93 Union 2332 CH/300/2xl3 under GIHG-PH and master key series GIHBG No. 79.10
F194 Yale 3203A/214.62 under MKAA and master key series MK48 No. 74.20
F195 Supply and install cyclinder mortice night latch lockcase “Accord No. 45.20
2332/1405”
F196 Supply and install cyclinder mortice night latch lockcase “Forte H6RP75ES” No. 35.40
F197 Take out locks, repair, oil and ease lock and refix to position No. 7.40
F198 Supply and fix double cylinder mortice lockset c/w handle Abloy 4190” No. 150.80
F199 Supply and fix single cylinder thumbturn lockset to aluminium sliding door No. 163.40
“Alboy 4960”
F200 Supply and fix double cylinder mortice lockset “Accord O7O6PZ/l591/1406” No. 98.60
F201 Supply and fix double cylinder mortice lockcase “Accord O7O6PZ” No. 46.50
F202 Supply and fix lockset for tempered glass door “Accord US1O/1406”” No. 317.30
F203 Supply and fix door spring for tempered glass door ‘Accord 853” including No. 243.80
alignment of glass doors
F204 Supply and fix cylinder knot set (5 Pin tumbler) “Goal US 5E” No. 33.60
F205 Supply and fix privacy knobset with emergency release “Goal US 4E” No. 29.50
F206 Supply and fix passage knob latch set “Goal US 1E” No. 27.80
F207 Supply and fix cylinder/tumbler turn deadbolt “Goal ADP-5/70-ll” No. 40.50
F208 Supply and fix single cylinder knobset (5-pin tumbler) “Lucky 1000” No. 20.90
F209 Supply and fix privacy knobset with emergency release “Lucky 1030” No. 20.90
F210 Supply and fix passage knot latchset “Lucky 1082” No. 19.90
F211 Supply and fix single cylinder knobset(5-pin tumbler) “Posse 100-SS” No. 22.10
F212 Supply and fix knobset with emergency release “Posse 130-SS” No. 22.10
F213 Supply and fix passage knot latchset “Posse 182” No. 19.80
F214 Supply and fix single cylinder deadbolt “Posse Dll8 SS” No. 35.90
F215 Supply and fix single cylinder deadbolt c/w inside thumbturn “Yale 8211” No. 27.90
SOR Page F13
F217 Supply and fix doable cylinder mortice lockset c/w handle “Trident No. 94.50
9000/1520/810”
F218 Supply and fix single cylinder knobset (5-pin tumbler) “Union 9308-SS” No. 24.40
F219 Supply and fix double cylinder mortice lockset c/w handle “Union 675-4l- No. 92.60
278SS”
F220 Supply and fix privacy knobset (5-pin tumbler) “Union 9301-SSO” No. 21.90
F221 Supply and fix passage knob latchset ”Union 9302-SS” No. 20.60
F222 Supply and fix double cyclinder mortice lockset c/w handle “Yale No. 77.80
138L/520.50/210.62”
F223 Supply and fix cyclinder mortice lockset with cast aluminium chrome plated No. 77.80
level handle “Yale l3BL/520.40/2l0.66”
F224 Supply and fix mortice dead lock “Yale 197” No. 80.60
F225 Supply and fix aluminium finish mortice level lockset “Yale No. 27.90
L315A/M246/21/2”
F226 Supply and fix lock to roller shutter “Viro 8202/8203” or other approved No. 27.30
F227 Labour for taking out lock from tempered glass door, repair, oil and ease No. 9.80
lock and refix in position
Cupboard Fitments
F229 Supply and fix plastic drawer track for cupboard fitments (one side) no. 7.70
F230 Supply and fix PVC coated metal drawer track c/w roller for cupboard no. 6.00
fitments
F231 Supply and fix 20mm diameter brass cupboard dead knob no. 3.00
Sawn Timber
F232 Supply and fix Sawn Kapoh or Keruing in wall plates, rafters, purlins, or m3 1633.60
joists, collars, etc. including tanalising or two coats wood preservative
* Supply and fix Sawn Kapoh or Keruing batten for tiles including tanalising
or two coats wood preservative *(F233 F236)
F239 Frame, head, mullion, transome, handrails, cill or boarding worked to the m3 1780.30
required shape
F240 Moulded architraves, cover fillets, etc not exceeding 500 sq mm in sectional m 1.50
area
F241 Moulded architraves, cover fillets, etc exceeding 500 sq mm and not m 2.20
exceeding 1,000 sq mm in sectional area
F242 Louvre blades or moulded skirtings not exceeding 2,000 sq mm sectional m 4.10
area
F243 Louvre blades exceeding 2,000 sq mm and not exceeding 4,000 sq mm m 4.10
sectional area
* Supply and fix Wrot timber worked to the required shape in small
quantities not exceeding 0.5m3 per job using *(F244 F246)
Plywood Panels
F255 Supply and fix 150mm x 30mm thick rubber protection guard with 2 nos. m 51.80
HRD-N fastener screws at 500mm centre to centre to walls of dustbin
compound
Locking Bar
F256 250mm long weld to 50mm x 100mm x 5mm thick flat handle No. 11.70
F257 300mm long weld to 50mm x 100mm x 5mm thick flat handle No. 12.30
F258 360mm long weld to 75mm x 100mm x 5mm thick flat handle No. 14.30
F259 460mm long weld to 75mm x 100mm x 5mm thick flat handle No. 15.10
F262 Supply and fix 13mm long stainless steel sike sharpen from 3.2mm No. 2.70
diameter rod complete with 35mm x 15mm x 3mm base plate including all
necessary fixing accessories
Ball Catch
F263 Supply and fix 60mm brass or satin nickel double ball catch to door, etc No. 8.20
F264 Supply and fix 2 pairs of 60mm brass or satin nickel double ball catch to Door 17.60
service duct door including removing existing night latch lockset, patching,
painting and making good affected area
Chicks/ Blinds
F265 Supply and install unlined split chicks constructed with ropes of No.8 white m2 26.90
glazed cord or nylon cord, 25mm diameter galvanised pulleys secured to
galvanised screws, hooks, size 18mm x 100mm brass clear fixed with brass
screws
F266 Extra over for item F258 to paint one side with one coat of primer, 1 m2 3.60
undercoat and 1 finishing coat of enamel paint
F267 Extra over for item F258 to line one side with first quality approved bluedrill m2 3.60
cloth or plastic cloth including binding the edge and allowance for all cutting
SOR Page F16
F272 Seal up existing shop fronts, etc exceeding 2.5m2 to vacant structures with m2 10.70
approved quality timber comprising 38mm x 75mm main framings (vertical
frames not more than 1500mm apart) and 2 numbers 25mm x 75mm
diagonal struts between vertical frames and filled in with 20mm x 100mm
horizontal boarding at 150mm centres
F273 Supply and erect 1.20rn high sawn timber fencing to be constructed with m 41.30
100mm x 100mm posts at 3.0Cm centres, 2 nos. of 100mm x 50mm
horizontal runners and 100mm x 20mm vertical boarding at 200mm
centres. The footings for posts shall be 225mm x 225mm x 300mm
concrete (1:3:6) . The whole fencing shall be strengthened with 100mm x
50mm slanting struts at every alternate post. Bottom end of struts shall be
cast in 225mm x 225mm x 225mm footing and top end secured to post.
Prepare and apply one coat of emulsion paint to both sides of fencing
F274 Supply and install ‘3M’ nomad dirt trap matting c/w “WELCOME” lettering at m2 78.70
centre
Perspex Sheet
F277 Take out serviceable hinges, locks, bolts etc and refix to new No. 2.00
doors/windows etc.
F278 Supply and fix pop rivets to aluminium louvre blade or other aluminium No. 0.40
fittings
F279 Supply and fix “Hilti” or other approved raw plug including use of gun and No. 2.40
explosive charges
F280 Refix wall mounted bin including all necessary drilling, fixing screws, rivet, No. 3.70
bolts, nuts, etc.
SOR Page F17
F282 Supply and install PVC curtain strip 300 x 2500 x 3mm thick, complete with No. 380.00
stainless steel bolts and nuts. 50% overlapping. Size 1900 x 2500
G – STEEL AND IRONWORKER
1 Rainwater Downpipe G1
2 Gratings G1 – G4
3 Welding G4
4 Flashing G5
5 Expansion Joints G5 – G6
7 Doors G6 – G8
8 Gates G8
11 Windows G8 – G11
14 Signage G12
30 Catladder G15
37 Miscellaneous G16
38 Supplementary G17
SOR Page G1
Rainwater Downpipe
Supply labour only for re-fixing loose brackets of rainwater down pipes.
Gratings
G009 Supply and fix hot-dipped galvanised steel drain cover grating for No 1.70
concealed drain, hinged on one side and overall 35mm thick fabricated with
25mm x 5mm intermediate flats spaced at 25mm centres resting on 10mm
diameter cross bar and support on 64mm x 38mm x 4.6mm angle
galvanised frame anchored to structure with fish tail complete with locking
bar
G010 * Supply and install mild steel vertical grating to 150mm wide scupper drain m2 170.30
surface water channel of the following depth comprising 10mm diameter
yertical bars spaced 38mm centre to centre, all framed up and welded to
19mm x 19mm x 3mm thick angle horizontal top piece and 25mm x 3mm
thick flat intermediate piece, the ends of horizontal top piece split and fixed
to sides of channel including 2 coats of bituminous paint. *(G011 G012)
* Supply and install mild steel vertical grating to surface water channel
exceeding 225mm but not exceeding 300mm wide of the following depth
comprising 10mm diameter vertical bars spaced 38mm centre to centre, all
framed up and welded to 25mm x 25mm x 5mm thick angle horizontal top
piece and 25mm x 5mm thick flat intermediate piece, the ends of horizontal
top piece split and fixed to sides of channel including 2 coats of bituminous
paint. *(G0l5 G0l6)
G017 Supply and fix galvanised steel wire balloon grating to top of 75mm to No 4.10
150mm vent pipes including spring clips and 1 coat of bituminous paint.
Railings
* Supply and fix Galvanised Steel Class ”A” Pipes of the following (internal
diameter) as railings in two horizontal rows and vertical supports at not
exceeding l.50m centres, bent to shape, necessary welding and filing
smooth all welded joints, cast in 200 x 200 x 300mm deep concrete (1:2:4)
foundation, painted with 1 priming coat, 1 undercoat and 1 finishing coat
*(G018 G022)
* Supply and fix Class “B” galvanised steel pipe of the following (internal
diameter) as railing in two horizontal rows, mild steel angle upstand at not
exceeding 2.5m centres, cast in 250 x 250 x 300mm deep concrete (1:2:4)
foundation, painted with 1 priming coat, 1 undercoat and 1 finishing coat
*(G023 G025)
G023 40mm diameter but with 65 x 65 x 6mm mild steel angle m 26.90
G024 50mm diameter but with 75 x 100 x 10mm mild steel angle m 36.90
G025 65mm diameter but with 88 x 113 x 10mm mild steel angle m 49.30
SOR Page G3
G027 Supply and install 38mm external diameter 2mmthick Grade 304 stainless m 34.50
steel handrail complete with 25.4mm external diameter stainless steel
supports spaced at not exceeding 1200mm centres and cast into reinforced
concrete structure including all necessary bending, welding and cutting
(Drawing No.. EM-TC-STD-BLDG-00-29A)
Supply and install 2mm thick stainless steel handrail with 25.4mm external
diameter stainless steel supports spaced at not exceeding 1000mm centres
complete with 120mm diameter x 4.5mm thick stainless steel plate and 3
nos. 5mm diameter raw bolts plugged onto wall for each support including
all necessary bending and cut (Drawing No. EM-TC-STD-BLDG-00--029A)
*(G028 G030)
G031 Supply and install stainless steel railing to parapet comprising of 40 x 40 x m 41.70
2mm thick grade 304 stainless steel hollow section welded with 30 x 6mm
thick grade 304 stainless steel flat supports spaced at not exceeding
1000mm centres and cast into concrete structure as specified including all
necessary bending and cutting
G032 Remove only and cart away existing railing including upstand in two m 4.30
horizontal rows with or without mild steel angle upstand.
* Supply and fix 2mm thick grade 304 stainless steel hand railing in the
following external diameters not exceeding 1.1m in height in two
horizontal rows including vertical upstands at not exceeding 1.2m centres,
necessary elbows at corners, finished smooth and polishing, cast in 200 x
200 x 300mm deep concrete(1:2:4) foundation (if necessary), including all
necessary excavation, hacking, removal of debris and reinstatement works
including all necessary bending and cutting *(G033 G035)
G033 38mm m 115.20
* Supply and fix 2mm thick Grade 304 stainless steel pipe in the follow
external diameters welded to narrow the gap of the horizontal rows for
stainless steel hand railing including all necessary bending and cutting
*(G036 G039)
G036 50.8mm - 2mm thk m 30.30
G041 Extra over for Item G040 for bending corner Per Bend 28.70
G042 Supply, fabricate and install G304 stainless steel flat bar for sectional Kg 10.70
area n.e. 400 mm2 including welded joints for staircase railing/
boundary railing/parapet railing/ etc.(7.93 kg/m2 per 1mm thick)
G043 Supply and install aluminium low jail bar barrier in powder coated or m 212.00
anodised finish including excavation, concrete foundation and
disposal of excavated materials off site
(Drawing no. EM-TC-STD-BLDG-0102-07)
G044 Supply and install aluminium low jail bar barrier in powder coated or m 231.00
anodised finish including aluminium cast base with anchorage bolts
(Drawing no- EM-TC--STD-BLDG-0102-07)
G045 Supply and install aluminium Double Row Guard Rail in powder m 117.00
coated or anodised finish including excavation, concrete foundation
and disposal of excavated materials off site
(Drawing no. EM-TC-STD-BLDG-0102-06)
G046 Supply and install aluminium Double Row Guard Rail in powder m 135.00
coated or anodised finish including aluminium cast base with
anchorage bolts (Drawing no. EM-TC-STD-BLDG-0l02-06)
G047 Extra over for additional horizontal row to Double Row Guard Rail m 23.00
G048 Extra over for additional horizontal or vertical diskonnect for turnings No. 40.00
Welding
G049 Weld loose, corroded or new steel work including the provision of m 17.10
welding rods, plant etc filing smooth, repainting to match existing and
the cutting and removal of corroded parts, if any. (New steel work
measured separately)
G051 Weld loose or new stainless steel members including the provision of m 21.50
stainless steel welding rods/ wires, brazing/welding plants etc and
filing smooth and polishing(stainless steel measured separately)
Flashing
G067 Supply and fix 0.996mm B.G. purpose-made aluminium not exceeding m 11.80
300mm girth to top of windows fixed with nails at 150mm centres to timber
frames including washers and sealing up joint with “Evomastic” or other
approved sealing compound.
G068 Supply and fix 0.996mm B.G. purpose-made aluminium flashing not m 14.80
exceeding 300mm girth fixed to wall with masonry or ramset nails at
150mm centres including cutting groove in wall to receive edge of flashing,
patching up with cement mortar and painting to match existing.
G069 Refix loose galvanised steel/aluminium window flashing with masonry or m 4.10
ramset nails at 150mm centres including re-cutting groove in wall and
patching up with cement mortar and painting to match existing.
* Supply and fix aluminium sheeting as cover, linings and flashing to roof
trap doors etc, including bending to required shape, aluminium
nails/screws and washers *(G070 G072)
Expansion Joints
G074 Exceeding 200mm girth but not exceeding 300mm girth m 17.60
G075 Refix loose aluminium expansion joint covers to walls including masonry m 2.20
nails and washers at approximately 150mm centres at both edges.
G113 Supply and fix 1.219mm thk aluminium WC/bathroom doors of size not No 108.00
exceeding
850 x 1800 including hook and band hinges, mild steel cotter pins and
brass shoot bolts/cabin hook.
G114 Supply and fix 1.219mm thk aluminium WC/bathroom doors of size not No 89.10
exceeding 850 x 1800 height including hook and band hinges, mild
steel cotter pins and brass shoot bolts/cabin hook.
G115 Supply and fix mild steel hook for aluminium wc bathroom door hinge No 5.70
SOR Page G7
G117 Supply and fix aluminium strap hinge including pop-rivetting to W.C./ No 4.30
bathroom door.
G118 Supply and fix approved aluminium strap locking bars of sizes 75mm to No 6.10
200mm long to hawker stalls aluminium door including additional aluminium
plate backing and pop-riveting.
G119 Supply and fix 50mm thick access trap door to RC roof overall size 1150 x No 449.20
1150mm comprising 1.2mm thick anodised aluminium alloy sheets on both
faces supported with 38 x 20 x 1.2mm thick galvanised steel channel
bracings and 60 x 38 x 1.2mm thick galvanised steel “C11 channel framings
infilled with rockwool insulation including approved hasp and staple, brass
rollers to manufacturer’s details in drawing (EM-TC-STD-BLDG-99-15, 16 &
17)
G120 Supply and fix plastic roller to roof access door No 11.70
* Supply and fix natural anodised aluminium sliding door (from approved
manufacturers) complete with sheet glass and all necessary fixtures and
fixing accessories. *(G121 G122)
G123 Supply and fix mild steel Sliding and Folding Door including all necessary m2 171.10
fixtures, accessories and 1 priming coat and 2 finishing coats of enamel
paint to match existing.
* Supply and fix natural anodised aluminium framed with glass panel
DOOR from approved manufacturers complete with all necessary fixtures
and fixing accessories etc (lockset, floor spring and door closer measured
separately) *(G124 G125)
G128 Supply and fix aluminium fixed full louvred door complete with 2.3mm thick m2 257.60
extruded aluminium louvred blades including all necessary fixing
accessories (Door frame to be measured separately)
(EM-TC-STD-BLDG-99-l9)
G129 Supply and fix mild steel door frame including fishtail holdfast m 31.80
G130 Supply and fix anodised aluminium half louvred and half panel door m2 283.30
including stainless steel or brass butt hinges and all necessary
ironmongery
SOR Page G8
G132 Supply and fix approved PVC door not exceeding 1.70m2 complete with No 120.40
lockset and necessary fixtures
G133 Supply and fix approved PVC door not exceeding 1.7 m2 but not exceeding No 131.90
2.1m complete with lockset and necessary fixtures
Gates
G134 Supply and install approved PVC door not exceeding l.70m2 complete with No 102.70
brass hook & eye and all necessary fixtures
G135 Supply and fix standard metal collapsible gates from approved m2 127.40
manufacturers including all necessary fixing lugs, guide rails, rollers and
gate locks. Prime and paint with 2 coats of aluminium paint
G136 Supply and install single or double leaf gate consisting of 50mm diameter m2 126.10
galvanised steel tubular framing filled in with 50 x 50mm weldmesh, 75mm
diameter galvanised iron tubular gate posts with bottom end encased in 450
x 450 x 600mm concrete (1:2:4) foundation, the gates hung on 2 pairs
approved hooks and ride hinges and fitted with approved locking bolt
including all necessary welding and painting (Net area of leaf measured)
G137 Supply and install mild steel grille gate fixed to metal gate frame, metal door Set 246.40
frame or timber door frame (frame measured separately) with and including
one primer coat(red lead primer or zinc chromate primer) and approved
mortice lock(but excluding hinges) of any flower patterns and sizes not
exceeding 940mm width x 2140mm height
G138 Supply and install 1.6mm thick aluminium plate to metal gate including m2 42.40
rivetting and taking out lockset and refix if necessary (new lockset
measured separately)
Windows
G139 Supply and fix Safety Catch/sash lock for aluminium sliding window No 2.10
G145 With 6mm thick obscure wired rough cast glass louvres m2 155.70
Supply and install 1.2mm thick natural /anodized extrude aluminium framed
2-tracked sliding window c/w sheet/float aluminium framing, ironmongery
and sill, etc including all necessary fixing, jointing materials and accessories
*(Gl47 G148)
G155 Extra over for cilia exposed to weather (1.2mm thick natural or bronze m 23.90
anodised aluminium)
G156 Supply and install 1.2mm thick bronze anodised extruded aluminium m2 204.90
framed casement window c/w 5mm thick tinted sheet/float glass, bronze
anodised aluminium framing, ironmongery, cill with cement mortar infill all
necessary fixing, jointing and accessories
G157 Supply and install 1.2mm thick bronze anodised extruded aluminium m2 219.70
framed top hung window c/w 5mm thick tinted sheet/float glass, bronze
anodised aluminium framing, ironmongery, cill with cement mortar infill. all
necessary fixing, jointing and accessories
SOR Page G10
G158 With 6mm thick obscured wired rough cast glass louvres m2 212.80
G160 Supply and install 1.2mm thick bronze anodised extruded aluminium m2 143.50
framed 2-tracked sliding windows c/w 5mm thick tined sheet/ float glass,
bronze anodised aluminium framing, ironmongery, cill with cement mortar
infill and all necessary fixing, jointing and accessories
G161 Supply and install 1.2mm thick bronze anodised extruded aluminium m2 165.50
framed 3-tracked sliding windows c/w 5mm thick tined sheet/ float glass,
bronze anodised aluminium framing, ironmongery, cill with cement mortar
infill and all necessary fixing, jointing and accessories
G164 Supply and install bronze aluminium sliding window grilles c/w cement m2 105.80
mortar and all necessary fixing, jointing and accessories
G165 Supply and install bronze aluminium fixed window grilles c/w cement mortar m2 98.90
and all necessary fixing, jointing and accessories
G166 Supply and install stainless steel crescent lock with double locking device to no. 6.60
aluminium sliding window
G167 Supply and fix adjustable louvred window with single control side frames for Set 9.70
8 Nos. 150mm wide glass or metal louvres in height including rattleproof
spring clips and all necessary bolts and nuts and fixed to wood, concrete or
brick etc. (Louvres measured separately.)
G168 Supply and fix adjustable louvred windows with dual control side frames for Set 12.20
8 nos. 150mm wide glass or metal louvres in height including rattleproof
spring clips and all necessary bolts and nuts and fixed to wood or brickwork
etc. (Louvres measured separately)
G169 Supply and fix burglar proof type adjustable louvred window with single Set 12.80
control side frames for 8 nos. 150mm wide glass or metal louvres in height
including rattleproof spring clips and all necessary bolt & nuts and fixed to
wood concrete or brick etc (Burglar proof bars and louvres
measured separately)
G170 Supply and fix burglar proof type adjustable louvred windows with dual Set 15.10
control side frames for 8 nos. 150mm wide glass or metal louvres in height
including rattleproof spring clips and all necessary bolts and nutts and fixed
to wood or brickwork etc but burglar proof type (Burglar proof bars
measured separately)
SOR Page G11
G172 Cost adjustment for each lourve add to (or deduct from items Gl33 to Gl36) No. 1.60
G173 Extra over for forming mullions for adjustable louvred window of any height No. 2.80
including spacers, bolts, nuts and screws.
G174 Supply and fix 1.588mm thk extruded aluminium lourved blades size not No 5.90
exceeding 600mm x 150mm wide in anodised finish to adjustable louvre
windows including pop rivets.
G175 Supply and fix 2.3mm thick extruded anodised aluminium lourves not m2 68.80
exceeding 600mm long
G176 Supply and fix 150mm wide x 5mm thick in polycarbonate louvre blade m 18.40
G177 Take down glass or metal louvres from adjustable louvre windows not Set 3.50
exceeding 12 louvres in height and stack aside for re-use, dismantle
existing damaged louvre frame from wall, timber frame and cart away
debris.
G178 Service and repair adjustable louvre window frame including the use of all Set 3.20
necessary additional spare parts, easing of windows, refixing same to wall
or timber frame (fixing of louvre blades measured separately)
G179 Fix existing metal louvre blade to adjustable louvre window frame with pop- No 0.90
rivets.
G181 Take down aluminium sliding windows/ doors, overhaul, ease, adjust and m2 9.30
grease all parts including all necessary repairs and refixing same
to slide properly.
Ceiling
G182 Supply and fix 600 x 600 x 0.5mm thk Trinet or other approved perforated m2 60.00
false ceiling complete with standard fixing accessories
* Supply and fix 600 x 600 x 0.7mm thk Dampa AL-C or other approved
unperforated aluminium false ceiling in the following colours complete with
standard fixing accessories *(G183 G184)
G185 Supply and fix Luxalon or other approved 0.5mm thick perforated metal m2 63.60
ceiling including framing and fillets
G186 Supply and install Luxalon or other approved 0.5mm thick perforated m2 77.60
aluminium ceiling including framing and fillets
G187 Supply and install 10mm thick GE Lexan thermoclear twin walled solar m2 141.40
control venetian polycarbonate sheet in standard tint complete with DS ‘168
black anodised aluminium clamping bar system and including fixing
accessories
SOR Page G12
* Supply, fabricate and fix mild steel such as angles, flats, plates, tees,
channels, hollow sections, rivets and bolts, etc of any size including welded
or bolted joints and painting one coat of lead and chromate-free primer
*(G197 G201)
G197 For cold formed hollow sections structural members only Kg 2.60
G198 For hot finished hollow sections structural members only Kg 3.00
G202 Extra over Item G196 to G200 for hot-dipped galvanising process not less Kg 0.50
than 20 microns by approved manufacturers
G203 Supply and fix 75mm diameter Class ”C” mild steel pipe as litter bin post No 47.00
not exceeding lm in height from ground level with top & bottom capping
welded together including excavation & embedding 300mm in
concrete (1:2:4) foundation, bracket for hanging bins and 1 coat of primer
and 2 coats of enamel paint
Signage
G209 Supply and fix metal house number plate sizes approximately 32mm x No 1.80
57mm with number of a1phabet embossed including all necessary painting
G210 Supply and fix plastic house number plates sizes approx. 40mm x 60mm No 0.80
height per digit
G211 Remove signage plates (any size) from walls and return to PA Office on No 8.90
instruction of Superintending Officer.
G212 Reinstall signage plates (any size) on wall with all necessary fixing No 10.70
accessories
G213 Collect old aluminium block number/address plates and refix them to wall at No 20.50
height to be directed by Superintending Officer including re-spraying plate
with one coat of black enamel paint and yellow illuminated paint.
G214 Remove from site damaged carpark sign posts or bollards No 10.10
G226 Supply and fix galvanised mild steel chequered plate, cut to size, including m2 49.50
all welding on site 2.5mm thk (net plate thickness)
* Supply and fix mild steel chequered plate, cut to size including all
necessary welding on site and 1 coat of bituminous paint *(G227 G228)
G229 3.0mm thk (net plate thickness) for lightning conductor pit cover centre No 2.80
drilled with a 20mm diameter hole
* Supply and fix aluminium chequered plate, cut to size including all
necessary bolting, etc. *(G230 G231)
G260 90 x 45 x 1.6mm thick jamb to opening size 900mm width x 2190mm height No 65.90
G261 130 x 45 x 1.6mm thick jamb to opening size 900mm width x 2190mm No 88.20
height
G262 145 x 60 x 1.6mm thick jamb to opening size 1000mm width x 2190mm No 96.90
height
Notice Board
* Supply and installation of notice boards to refer to the Term Contract for
the Supply and Installation of Carpark, Traffic Sign and Estate Signboard
(*G271 G274)
G271 Supply & fix 3mm thick clear transparent polycarbonate cover m2 80.00
G272 Supply only 3mm thick clear transparent polycarbonate cover m2 45.00
G274 Supply and fix 2mm thick adhesive board backing m2 45.00
SOR Page G15
G276 Supply and fix 5mm thick clear polycarbonate or acrylic plastic sheet in m2 92.50
panel to Notice Board including rubber glazing where necessary
G277 Supply and fix 12.7mm thick soft board velvet fabric to Notice Board m2 51.00
G278 Remove notice board and store in PA office or as directed including making No. 20.20
good disturbed work
G279 Supply and fix 25mm x 3mm x 230mm long galvanised wrought iron No 1.10
holdfast one end turned up and screwed to frame, other end fishtailed and
slot into wall.
G280 Cut into existing wall and fix 25mm x 3mm x 23 0mm long galvanised No 4.50
wrought iron holdfast
Ramset Nail
G281 Supply and fix ramset nail including the use of gun and explosives. No 0.80
Staircase Nosing
G282 Supply and fix Stainless steel stair nosing size 50mm x 35mm x 1mm thick m 16.10
of grade 304 with fishtail holdfast bedded in cement mortar all as specified
in detailed drawing (EM-TC-STD-BLDG-99-02)
Cat ladder
G283 Supply and fix 350mm wide aluminium ladder comprising aluminium C m 83.50
channel and 25mm diameter aluminium tubular rungs at 305mm c/c to roof
top water tank room/pump room/etc.
Flushout Pipe
G284 Supply and fix additional brackets to external flush out pipes and external No. 21.70
main risers with anchors set in brick wall or concrete wall in detailed
drawing(EM-TC-STD-BLDG-99-20)(Gondola and scaffolding to be paid
separately)
G287 Supply and fix 38mm diameter x 250mm long stainless steel Grade 304 no. 11.20
pipe socket
G288 Supply and install stainless steel angles, flats, plates, tee, channels, etc. of kg 7.70
any size fabrication including welded or bolted joints
Metal Sunlouvres
G294 Supply and install 1mm thick Unisun Cl00 blades c/w 30 or 45 degrees m2. 132.00
Dasolas panel holder clips at 100mm pitch, 20 x 30 x 3mm thick support
rafters, 75 x 75 x 6mm thick support rafter brackets in stoved polyester
coating and stainless steel bolts and nuts
G295 Supply and install 1mm thick Unisun Cl00 blades c/w black 60 degrees m2. 176.00
Dasolas panel holder clips at 100mm pitch, 20 x 30 x 3mm thick support
rafters, 19 x 19 x 3mm thick bracing stuts, 3mm thick bracing stuts
brackets/gliders, 75 x 75 x 6mm thick support rafter brackets in stoved
polyester coating and stainless steel bolts and nuts
Miscellaneous
G296 Labour refixing loose galvanised steel/ aluminium window flashing with m 4.10
masonry or ramset nails at 150mm centres and re-cutting groove in wall
and patching up with cement mortar and painting to match existing
G297 Supply and fix approved 16mm x 16mm x 1.27mm anodised finish No 1.90
aluminium angles to timber louvres not exceeding 53 0mm long including 4
nos. 6mm long No.4 pan-head tapering screws
G298 Galvanised gauze to openings of precast concrete vent fixed with timber m2 81.40
fillets
SOR Page G17
G300 Supply and fix 300mm black Jappanned gallow brackets No 3.50
G301 Fixing only loose gallow brackets including additional rawl or wood plugs No 1.10
G302 Cut into existing wall and incorporate new 25mm x 3mm x 230mm long No 4.70
wrought iron holdfast and filled up hole with concrete, reinstate plaster to
surface and painting to match existing
G303 Labour welding back broken or loose hinges to mild steel casement window No 10.10
leaf or frame including easing to shut properly and touching up surfaces to
match existing
G304 Labour for removing defective steel hinge from mild steel casement No 16.50
windows, supply new approved hinge including all necessary rivetting,
welding, easing to shut properly and touching up surfaces to match existing
(labour inclusive of taking out and refixing of glass, if found necessary)
G305 Supply and fix metal casement windows with/without top hung, complete m2 119.20
with frames, glazing, putting, all necessary accessories and 3 coats of
enamel paint
G306 Labour and material for refixing fallen mild steel clothes drying rack to No 3.20
ceiling with Hilti M6 or other approved
G308 Labour and material of shop premises for taking down mild steel sliding and m2 11.10
folding door to overhaul, cease, adjust and grease all parts including all
necessary repairs! welding and replacement of all damaged tube knucklers,
hinges and gulders, etc and reinstall to slide properly
G309 Labour and transport for dismantling and removal of casement/ sliding/ m2 8.50
louvred window from site including frame (if any)
G310 Labour and transport for dismantling and removal of metal gate from site No 22.00
G311 Labour and transport for dismantling and removal of collapsible gate from m2 11.10
site
G3l2 Labour taking out existing metal window grilles from windows and/or m2 5.00
balcony and remove from site
G313 Labour taking out existing metal window grilles and refix in position m2 7.90
including provision of new screws where necessary
Supplementary
G315 Supply and fix approved manual operated natural anodidized aluminum m2 120.00
roller shutter including fixtures box like enclosure & accessories, and
removal of existing damaged roller shutter where applicable
H – PLASTERER AND WALL TILER
1 Plastering H1
2 Glazed Tiling H1
3 Ceramic Tiling H2
4 Mosaic Tiling H2
5 Terrazzo H2
6 Slate Tiling H2
7 Granite Tiling H2
9 Spalling Concrete H3
10 Hacking Works H3
11 Patching Works H3 – H4
12 Skim Coating H4
13 Miscellaneous H4
SOR Page H1
Plastering
H005 Extra over plastering for forming 20 x 15mm deep groove lines to wall, m 2.00
columns, beams etc as specified
H006 Extra over for waterproofing compound in accordance with the m2 1.40
manufacturer’s instructions incorporated in the plaster works (applicable to
other plasterer items)
H007 White marble chipping Shanghai Plaster to walls including minimum 13mm m2 30.80
thick cement and sand screed backing (1:3)
Glazed Tiling
H008 108 x 108 mm white glazed tiling to walls including coved or rounded edged m2 33.00
tiles etc and cement and sand screed (1:3)
H009 150 x 150 mm white glazed tiling to walls including coved or rounded edged m2 41.70
tiles etc and cement and sand screed (1:3)
H010 108 x 108 mm coloured glazed tiling to walls including coved or rounded m2 35.20
ed9ed tiles etc and cement and sand screed (1:3)
H011 150 x 150 mm coloured glazed tiling to walls including coved or rounded m2 45.20
edged tiles etc and cement and sand screed (1:3)
H012 100 x 200 mm white glazed tiling to walls including coved or rounded edge m2 37.40
tiles etc and cement and sand screed (1:3)
H013 100 x 200 mm or 200mm x 200mm white based floral tile to wall including m2 40.00
coved or rounded edged tiles etc and cement and sand screed (1:3)
H014 Supply and lay 100mm x 200 mm or 200mm x 200mm coloured based m2 49.00
floral tile to wall including coved or rounded edged tiles etc and cement and
sand screed (1:3)
SOR Page H2
H015 Supply and lay ceramic tiles (Heavy Duty) of any sizes minimum 8mm thick m2 41.85
including coved or round edges of approved colour and pattern, jointed,
pointed, on and including minimum 13mm thick cement and sand backing
to wall (1:3)
H016 Supply and lay homogeneous polished wall tiles of any sizes minimum m2 54.90
8mm thick including coved or round edge tiles of approved colour and
pattern, jointed, pointed on and including minimum 13mm thick cement and
sand backing (1:3) to wall
H017 Supply and lay homogeneous unpolished wall tiles of any sizes minimum m2 43.20
8mm thick including coved or round edge tiles of approved colour and
pattern, jointed, pointed on and including minimum 13mm thick cement and
sand backing (1:3) to wall
H019 Exceeding 0.3m2 and not exceeding 0.5m2 per patch No. 32.60
H020 Exceeding 0.5m2 and not exceeding 1m2 per patch No. 65.20
Mosaic Tiling
H021 Supply and lay unglazed mosaic tiles 19mm x 19mm or 25mm x 25mm m2 39.80
walls including coved tiles etc and cement and sand screed(1:3)
H022 Supply and lay semi-glazed mosaic tiling to walls including coved tiles etc m2 40.60
and cement and sand screed (1:3)
H023 Supply and lay glazed mosaic tiling to walls including coved and rounded m2 44.40
edge tiles etc and cement and sand screed (1:3)
Terrazzo
H024 Supply and lay 20mm thick terrazzo on brick, block or concrete walls, m2 38.40
column surface polished including cement and sand screed (1:3)
Slate Tiling
H025 Supply and lay natural slate tiles of 10-15mm thick in any approved colours m2 38.40
and pattern jointed and pointed on and including 13mm thick cement and
sand backing(1:3) to wall
Granite Tiling
H026 Supply and lay l0mm-l3mm thick polished granite slabs of approved colour m2 110.80
and pattern, jointed, pointed on and including minimum 13mm thick cement
and sand backing(1:3) to wall
H027 Supply and lay lOmm-l3mm thick unpolished granite slabs of approved m2 93.10
colour and pattern, jointed, pointed on and including minimum 13mm thick
cement and sand backing(1:3) to wall
SOR Page H3
H028 Supply and lay 15mm thick pebble wash finish (pebble size 3mm to 5mm) m2 42.00
to wall, columns, etc. laid in section including provision of all necessary
groove lines
Spalling Concrete
H029 Hack 13mm ‘V’ groove along crack, apply primer and patching with epoxy m 10.90
mortar (inclusive of related works covered in the drawing and specification)
(EM-TC-STD-ELDG-99-04)
H030 Repair of spalling concrete by patch repair with approved epoxy mortar m2 144.00
(inclusive of hacking and other related works covered in the drawing and
specifications)(EM-TC-STD-BLDG-99-04)
H031 Repair of spalling concrete by patch repair with approved polymer modified m2 50.30
sand-cement mortar (inclusive hacking and other related works covered in
the drawing and specifications)
(EM-TC-STD-BLDG-99-04)
H033 Extra over item H032 for area exceeding 0.65m2 m2 205.50
H034 Repair to cracks by epoxy injection method including painting to repaired m 42.00
surfaced as specified
H035 Repair to cracks by hacking “V” groove along cracks and patch with
approved polyurethane sealant including painting to the repaired surface m 16.00
Hacking Works
H036 Hack out cracks in concrete walls, slabs, soffits and floors to form “V” m 3.50
shaped grooves approximately 25mm wide x 37mm deep, make good with
cement mortar (1:3) and touch up paintwork to match existing
H037 Hack out cracks in concrete walls, slabs, soffits and floors to form “V” m 3.90
shaped grooves approximately 25mm wide x 37mm deep make good with
prepacked MORTAR mixed and touch up paint work to match existing
H038 Hack existing plastered or concrete wall surface to form random keys, clean m2 2.10
and wash to receive new finish
H039 Hack off existing damaged plastering, glazed wall tiles/terrazzo/mosaic tiles m2 2.00
and re-form keys on wall, tables and stools to receive new finish
Patching Works
H042 Patch existing holes not exceeding 150mm square sectional area in walls, No 0.80
ceilings etc with cement mortar or putty and touching up painting to match
existiig
Skim Coating
Skim coat of approved prepacked skimming material applied from within the
building *(H043 H044)
H047 Prepare and apply skim coating to external rc surfaces in two coats to a m2 8.00
maximum total thickness of 6mm using approved prepacked skimming
materials according to manufacturer’ s instructions 18mm thick plastering
with approved prepacked MORTAR mixed to RC surface, brickwalls and
block walls, etc as specified *(H048 H049)
Miscellaneous
H050 Supply labour for laying tiles (any grades, sizes, colours and patterns) m2 20.00
including 13mm cement and sand screed (1:3) and pointing, to wall
H051 Pull out nails, hooks etc from walls and ceilings and patch up hole including No 0.50
touching up painting to match existing
H052 Re-pointing joints of existing wall tiling in white cement including cleaning m2 2.40
surface on completion
H053 Prepare and wash with high water jet and hypochloride acid or approved m2 3.00
detergent to remove all surface contaminants on all surfaces
1 Glass Panes I1
2 Glass Lourves I1
SOR Page I1
Glass Panes
Glass Louvres
* The following in louvres (varying from 100 to 200mm wide) ordinary
quality clear float/obscured glass with ground and polished edges fixed to
metal or timber frames *(1014 1018)
I018 Provide and apply putty for securing glass panes to metal windows m 0.70
including removal of damaged putty
J – PAINTER
2 Aluminium Paint J3
5 Pesticide Paint J4
6 Bituminous Paint J4
8 Varnish to Woodwork J4
9 Spray Paint J4
10 Wood Preservative J5
12 Miscellaneous J5 – J6
SOR Page J1
* Painting plain surfaces of woodwork and metal work etc, including sand
papering as specified *(J001 J002)
* Painting pipes, railing, etc not exceeding 75mm diameter (round section)
or not exceeding 250mm girth (square or rectangular section) or galvanised
chain to swing including sand papering as specified *(J007 J008)
* Painting pipes, railing, etc exceeding 75mm diameter but not exceeding
150mm diameter (round section) or exceeding 250mm but not exceeding
450mm girth (square or rectangular section) including sand papering as
specified *(J009 J010)
* Painting fillets, glazing bars, etc not exceeding 150mm girth *(J015 J016)
J019 Cleaning and painting to fan blade and cage in one undercoat and one No 10.70
finishing coat
J020 Painting metal surface with one coat approved lead and chromate free m2 2.40
primer
J020 Painting non-ferrous metal surface with one coat of approved etching m2 2.25
primer
* Painting to 50mm diameter Bird Hanging Pole exceeding 5 metre but not
exceeding 6 metre height *(J022 J023)
J024 Painting one undercoat and one finishing coat of synthetic paint to external No. 10.90
surface of timber door including door frames to door openings not
exceeding 2.5m2
J025 Painting one finishing coat of synthetic enamel paint to both faces of m.s. No. 7.00
gate not exceeding 2.5m2
SOR Page J3
* Painting metal collapsible gates, iron folding gate etc. (Measured flat
overall. Rate inclusive of painting to both faces) *(J028 J030)
* To pipes, railing, etc exceeding 75mm diameter but not exceeding 150mm
diameter including sand papering as specified *(J033 J034)
J036 Two coats (with maximum 10% dilution for first coat, and without water m2 1.90
dilution on second coat)
J037 Three coats (with maximum 10% dilution for first coat, and without water m2 2.60
dilution on second and third coats)
J039 Two coats (with maximum 10% dilution for first coat, and without water m2 2.30
dilution on second coat)
J040 Three coats (with maximum 10% dilution for first coat and without dilution to m2 3.30
second and third coats)
SOR Page J4
J042 Two coats (with maximum 5% dilution for first coat and without water m2 3.10
dilution on second coat
Bituminous Paint
J043 Prepare and apply 1 coat of non-toxic bituminous paint on surface of mild m2 1.90
steel plate & rolled steel joists
J044 Mild steel drain cover gratings (measured separately) dipped in Bitutect No. m2 2.50
1 or approved bituminous paint (rate inclusive of both faces)
Varnish To Woodwork
J048 Stain, prepare and apply 2 coats shellac varnish on new or existing m2 6.30
woodwork
J049 Prepare and apply two coats of approved stain and wax polish or m2 6.10
polyurethane varnish on general surfaces of woodwork
Spray Paint
J050 Spray painting on plain surface of metal work in one finishing coat of m2 2.00
synthetic enamel paint
J051 Spray paint lettering (300mm in height) to CRC roller shutter surface “No No 48.30
Parking Fine Max. $1,000/-”.
J055 Spray painting of minimum 75mm high numerals and letterings to bin chute No 1.50
chamber door, storey indicator, pipes service duct doors, dry riser inlet
panel etc (‘No” means per pipe/door/dry riser/inlet panel/indicator)
SOR Page J5
J061 Brush, wash down and apply one coat water-based sealant on concrete or m2 1.00
plastered surfaces
J062 Paint existing column edge angle bar at carpark using illuminated/ m 1.70
fluorescent paint
J065 Paint existing table tennis top and exposed edges with 2 coats approved No 45.00
paint, mark out new lines and 2 coats of enamel paint to steel hollow
section frames
* Painting to pipe at roof top not exceeding 150mm diameter including sand
papering using approved ceramic insulation coating *(J066 J067)
* Painting to pipe at roof top exceeding 150mm diameter but not exceeding
300mm diameter including sand papering using approved ceramic
insulation coating
*(J068 J069)
m 6.00
J068 One finishing coat
m 10.20
J069 One undercoat and one finishing coat
J070 Apply one coat of rust inhabitor primer to metal surface to receive new m2 3.60
coating
SOR Page J6
J073 Skilled labour to sand wood surfaces to a perfect even surface and clean m2 1.60
surface to receive new finish including all necessary equipment, tools and
accessories
Prepare, align, set out and apply manually quick drying chlorinated rubber
based paint on concrete surface (any colour) *(J074 J075)
Clean and apply wax polish to general surface of marble, terrazzo, mosaic
or other finish and polish manually or with machine including all necessary
equipment, tools and accessories *(J076 J077)
J078 Prepare, grind manually or with machine complete with 2 process of wax m2 12.60
polish on general surfaces of marble, terrazzo or other finish including all
necessary machineries/tools and accessories
K – NOT IN USE
L – DAYWORK
1 Labour L1
2 Plant L1 – L2
5 Timber Scaffold L3
6 Metal Scaffold L3
9 Testing of Materials L4 – L6
Labour
Plant
L023 Motor Lorry (Pick-up) not more than 2.50 tonne including fuel and driver Hr 14.00
L024 Motor Lorry 3 tonne size including fuel and driver Hr 19.90
L025 Motor Lorry 7 tonne size including fuel and driver Hr 21.90
L026 Motor crane including fuel and driver (3 tonne lifting capacity) Hr 25.10
SOR Page L2
L028 Wheel or crawler shovel or excavator loader with back hoe bucket not Hr 47.40
exceeding 0.4 cu m or 1.30 cu m loader bucket capacity including fuel and
driver e.g. Kobe 904, JCB
L029 Power loader or rubber-tyre wheels 1.20 cu m bucket capacity (Flywheel Hr 40.90
horse power 60 KW range) including fuel and driver
L030 Traxcavator 1.00 Cu m capacity including fuel and driver eg. CAT 933 Hr 49.70
L033 Diesel powered field welding machine with minimum capacity 300 amp Hr 8.80
L036 Submit drawings and roof plans by Professional Engineer to the relevant Block 402.50
Authorities for approval (building having similar roof plans/design shall be
included in this rate and shall NOT be paid separately under one operation)
L037 Carry out testing of mechanical suspended cradles by (M & E) Professional Test 230.00
Engineer and obtain approval the relevant Authorities
L038 Supply and install mechanical suspended cradle not exceeding 5 metres Unit 575.00
length to the roof including PE endorsement certifying the proper
installation of suspended cradle according to the PE’s design calculations,
drawings and roof plans (hiring charges and shifting shall be paid
separately)
L039 Hiring charge of approved mechanical suspended cradle not exceeding 5m Day 60.00
length including all accessories and safety precautions
L040 Labour for shifting approved mechanical suspended cradle within the same Shift 30.00
block by one gang
L041 Labour for shifting approved mechanical suspended cradle within the same Per 50.00
block by one gang for more than one shift per day (Per Job means Multiple Job
Shift per Day)
L042 Per stage of exceeding 6 metres and not exceeding 8 metres high. No 75.50
L043 Per stage of exceeding 8 metres and not exceeding 10 metres high. No 90.00
SOR Page L3
L044 Erect double layer timber scaffolding including taking down after use (height m2 4.60
of scaffolding not exceeding 15m high. A minimum of 5 metre width shall be
paid)
Metal Scaffold
L045 Erect metal scaffolding not exceeding 15 metre height including taking m2 11.50
down after use
L046 Erect metal scaffolding exceeding 15 metre height but not exceeding 35 m2 12.70
metre height including taking down after use
L047 Submit drawings and design calculations by Professional Engineer to the Blk 402.50
relevant Authorities for approval to install mobile lifting platform (building
having similar plans/designs shall be included in this
rate and shall NOT be paid separately under one operation)
L048 Submit the certification of supervision by Professional Engineer certifying Test 207.00
the proper installation of mobile lifting platform according to the
Professional Engineer’s design calculations and drawings
L049 Carry out test of mobile lifting platform by approved person (PE Structural Test 345.00
Engineer and PE Mechanical Engineer) from the relevant authorities
L050 Supply and install Single Mast Mobile Lifting platform not exceeding 11 Unit 920.00
metres length including subsequent removal off site upon completion of
work, making good to affected area (hiring changes shall be paid
separately)
L053 Labour for shifting approved Drive Unit Mast Platform including supervision Shift 690.00
by Professional Engineer
L054 Transportation and installation of self-propelled Aerial Platform/Boom lift on no. 276.00
site and subsequent removal off site upon completion of work including
make good to affected area (Hiring charge shall be paid separately)
Testing of Materials
L064 Pull out test for plaster (Per point for external) point 92.00
L065 Pull out test for plaster (Per point for internal) point 92.00
L066 Pull out test for brick tile (Per point for 200 x 200mm) point 115.00
L067 Polymer Modified Sand Cement Mortar : Compressive Strength Test (Test age 345.00
Method ASTM C109 1992)
L068 Polymer Modified Sand Cement Mortar : Setting Time Test (Test Method : test 345.00
BS4550 : Part 3 Section 3.6 : 1987)
L069 Polymer Modified Sand Cement Mortar Shrinkage Test (Test Method : test 690.00
ASTM C531 : 1995)
L070 Polymer Modified Sand Cement Mortar : Bond Strength Test (Test Method age 517.50
ASTM C190 1985)
L071 Polymer Modified Sand Cement Mortar : Polymer Solid Content Test(Test test 920.00
Method : Chemical Analysis)
L072 Polymer Modified Sand Cement Mortar : Air Permeability Test(Test Method test 690.00
: Modified Figg Air Test)
L073 Non-shrink Pressure Grout Flow Consistency Test (Test Method ASTM test 115.00
C939 - 93)
L074 Non-shrink Pressure Grout Expansion/ Shrinking Test (Test Method ASTM test 345.00
C940 - 89)
L075 Non-shrink Pressure Grout Bleeding Test (Test Method ASTM C940 - 89) test 172.50
SOR Page L5
L077 Non-shrink Pressure Grout Compressive Strength Test [Test Method ASTM test 230.00
C942 - 88 (1991)]
*Supply labour and materials for cleaning up and washing with detergent,
sweep dry and damp mop the following: *(L075 L084)
*Supply labour and materials for cleaning up and washing first with
detergent, sweep dry, then damp mop with Clorox or other approved
consecutively for three times, open all windows and main entrance door to
air the flat for one hour including spraying of deodorizer to the whole flat
*(L085 L089)
L090 Labour for removal of unwanted furniture, fitting, fixings, etc c/o metal, Item 4.00
plastic, wood, glass and other compressed materials of total quantities
requiring only one labour to the skip tank/dustbin compound and
designated area within site, fiot exceeding 0.5 cu m (measured in original
overall dimensions)
L091 Labour for removal of unwanted furniture, fitting, fixings, etc c/c metal, Item 8.10
plastic, wood, glass and other compressed materials of total quantities
requiring two labourers to the skip tank/dustbin compound and designated
area within site, not exceeding 0.5 cu m but not exceeding 2.O cu m
(measured in original overall dimension)
L092 Labour for removal of unwanted furniture, fitting, fixings, etc c/o metal, Item 12.10
plastic, wood, glass and other compressed materials of total quantities
requiring two labourers to the skip tank/dustbin compound and designated
area exceeding 2.O cu m (measured in original overall dimension)
SOR Page L6
L099 Supply of skip tank for unwanted articles and debris (not exceeding 20m2) No 345.00
including removal and cast away to approved dumping ground (Rate
inclusive of ENV fees, etc.)
M – NOT IN USE
N – CEILING LEAK REPAIRS
1 Repair of Leaks N1
2 Floor Finishings N1 – N2
3 Waterproofing N2
SOR Page N1
Repair of Leaks
N001 Hack away existing plasterwork to expose building components for visual Patch 15.00
inspection inclusive of reinstatement works to match existing (for areas not
exceeding 0.20 m2 per patch)
N003 Expose the concrete surface, grind, dampen and apply crystalline m2 15.00
waterproofing material as specified
N004 Repair water seepage through porous concrete by injecting approved water m 56.00
reactive polyurethane based chemical grout as specified
N005 For area not exceeding 3.5m2 (per unit) Job 122.50
N007 Repair to water leakage through floor slab around sanitary piping/floor trap Point 72.00
using approved water plug or non-shrink grout inclusive of the use of
bonding agent and make good the repaired area with waterproofed mortar
and floor tiles to match with the existing floor tiles and bedding around pipe
and other related works as specified
N008 Rectification of sanitary opening on rc slab to details as specified and Job 125.00
shown in drawings attached (per unit) (tiling work measured separately)
N009 Add to last item for each additional opening in the same unit Job 50.00
N010 Extra over rectification of sanitary opening for ceramic floor tiles finish m2 62.00
N011 Extra over rectification of sanitary opening for mosaic floor tiles finish m2 51.50
Floor Finishes
N012 For area not exceeding 3.5m2 (per unit) Job 191.00
* Supply and lay homogeneous ceramic floor tiles on cement and sand
(1:2) screed with approved waterproofing additive by weight (a minimum
thickness of 13mm at the lowest end of the fall) to match with the
surrounding inclusive of bedding screed and other related works as
specified *(N0l4 N015)
N014 For area not exceeding 3.5m2 (per unit) Job 220.00
N016 For area not exceeding 3.5m2 (per unit) Job 189.00
N018 Extra over for floor finishes repair to water leakage through floor slab Point 35.00
around sanitary piping/floor slab or other porous area using approved
water plug or non-shrink grout inclusive of the use of bonding agent
Waterproofing
* (N019 N021)
* Supply tools and skilled workers to check all sliding, top and side hung
casement windows in unit building for compliance with PA’s requirements
and give inspection checklist to owner including transportation cost
Q008 5mm thick green grey/grey tinted float glass in panes m2 35.00
Q009 6mm thick obscured wired rough cast glass louvres m2 45.00
Q015 Supply and fix in replacement bronze anodised extruded aluminium framed m2 200.00
adjustable louvred vents complete with aluminium “U” clips/holders, 6mm
thick obscured wired rough cast glass louvres and all necessary fixing and
jointing materials and accessories as specified (measurement based on
size of opening)
TERM CONTRACT FOR BUILDING WORKS
*Supply and install perspex sheet to walls, columns and doors of toilets as shown in drawing
no.: EM-TC-STD-SIGN(E)-1002-04; Overall size: 0.2m X 0.3m X 3mm thick
*(374-375)
*Supply and install Perspex sheet to walls, columns and doors of toilets as shown in drawing
no.:EM-TC-STD-SIGN(E)-1002-04; Overall size 0.15m X 0.15m X 3m thick
*(376-377)
378 Supply and install 3mm thick Perspex sheet with any graphics or wordings ro walls and No. 30.00
columns; any sign
379 Supply and install stainless steel sign; Overall size 0.3m X 0.44m X 0.08m thick No. 350.00
Arrow sign as shown in drawing no.: EM-TC-STD-SIGN(E)-1002-04 including all approved
mounting accessories
*Supply and install acrylic sheet with reversed silkscreen printing (any background colour) c/w
4 nos. stainless steel counter-sunk screws and plastic plus (letterings to be paid separately
* (380-381)
2mm thick
380 No. 50.00
4mm thick
381 Illuminated block number sign from wall No. 120.00
SOR Preamble
1. The rates contained herein include the use of materials, labour, maintenance, supply of fuel and
all idling time of vehicles, opening up, taking down, cutting and refixing preparation for washing
turning on and off of water supply, tightening bolts and nuts (where necessary) provision of
standby plumbers, ladders and torchlights, other tools / equipment and removal of all debris,
empty tins and other unwanted materials from the roofs, all as specified, including making good
all leaking tank panels with approved sealants where necessary), fitting, fixing in position, all
cutting and waste, return of packings, establishment charges, overheads, profit and all forms of
claim of loss and expense and making good all work disturbed, unless otherwise stated.
2. The rates of painting of water tanks unless otherwise stated included the preparation of surfaces
as per manufacturer’s recommendation and the Employer’s instructions. No dilutions of coating
materials are allowed unless recommended by the manufacturer and the Employer. The
application of coating materials shall comply strictly to the manufacturer’s recommendations and
the Employer’s instructions.
3. The rates are applicable for work carried out in the Market/Hawker Centres, eating houses and
other premises as directed by the Superintending Officer.
4. The cost of hacking, removal and disposal, and the making good of all affected works shall be
deemed to be included in the Schedule of Rates unless otherwise stated. All schedules of Rates
shall be applicable for new and replacement work.
5. Unless otherwise stated, all works shall be measured nett as fixed in its place. Pay length of
pipes shall be measured on exposed length.
6. All pipes are described by their normal size except copper, stainless steel, and upvc pipes which
are meant to be their normal size.
7. The Employer reserves the right the direct the Contractor to execute any of the undermentioned
items of works which he considers necessary.
8. All rates in the Schedule shall include all necessary materials and waste, plant, staging and
scaffolding (only applicable up to 6m high, any height above 6 metres shall be paid separately,
measuring from ground level, i.e. from the base for which scaffolding rests unless specified
otherwise.
SCHEDULE OF RATES
CONTENTS
8
SOR Page 2
B005 Extra over concrete bed to 100mm diameter pipe for m 5.20
Concrete Grade 20 surround minimum 150mm thick.
B006 Extra over concrete bed to 150mm diameter pipe for m 7.30
Concrete Grade 20 surround minimum 150mm thick.
D003 Purpose made mild steel pipe brackets to pipe not No. 6.60
exceeding 100mm diameter (Scaffolding measured
separately)
D004 Cast iron pipe brackets to soil waste or rainwater down No. 5.10
pipes not exceeding 100mm diameter (Scaffolding
measured separately)
D005 Cast iron pipe brackets to soil waste or rainwater down No. 6.60
pipes exceeding 100mm diameter (Scaffolding
measured separately)
D008 Galvanised steel holder bats or clips for water pipes No. 1.30
not exceeding 25mm diameter
D009 Galvanised steel holder bats or clips for water pipes No. 1.30
exceeding 25mm but not exceeding 50mm diameter
D010 Galvanised steel holder bats or clips or water pipes No. 2.00
exceeding 50mm diameter
D012 Per stage of exceeding 6 metres and not exceeding 8 No. 75.50
metres high
D013 Per stage of exceeding 8 metres and not exceeding 10 No. 90.00
metres high
SOR Page 5
D014 Mild steel hangers for 75 mm diameter UPWC waste No. 13.40
or soil pipe
D015 Mild steel hangers for 100mm diameter galvanised No. 16.60
UPVC pipe
D017 13mm diameter blots, nuts and washers for flange joint No. 2.00
or outer fitting
D018 17mm wide punched steel for hanging cast iron pipe No. 6.20
etc (Band not exceeding 1.0 meter long)
SOR Page 6
Manhole Construction
Manhole Cover
E008 32 Kg cast iron light duty manhole cover ad frame No. 35.00
including settling frame in cement mortar (1:3) and
sealing cover in grease and fine sand.
E009 22 Kg cast iron light duty manhole cover only No. 32.00
(excluding frame)
E010 52 Kg cast iron heavy duty manhole cover only No. 55.10
(excluding frame)
E011 600 X 450mm recessed type cast iron manhole cover No. 37.20
and frame
E012 Mild steel cover and frame 300 X 300mm for rain water No. 24.50
down pipe sump
E013 “PC” Brand or other approved cast iron light duty No. 32.40
manhole cover with lifting device only (excluding
frame)
E014 “PC” Brand or other approved cast iron light duty frame No. 32.50
only (excluding cover)
SOR Page 7
E016 Cut 2mm line at handle-area of cast iron manhole Cover 2.70
cover.
G003 Extra over 100mm diameter pipe for “duck” foot bend No. 41.80
G004 Extra over 150mm diameter pipe for “duck” foot bend No. 55.60
G005 50mm diameter cast iron pipes with socketted joints m 16.80
caulked with hemp and molten lead.
G006 75mm diameter cast iron pipes with socketted joints m 20.30
caulked with help and molten lead.
G007 100mm diameter cast iron pipes with socketted joints m 22.80
caulked with hemp and molten lead.
G008 150mm diameter cast iron pipes with socketted joints m 32.90
caulked with hemp and molten lead
G009 50mm diameter cast iron bend with cleaning eye. No. 10.40
G010 75mm diameter cast iron bend with cleaning eye No. 13.80
G011 100mm diameter cast iron bend with cleaning eye No. 18.45
G012 150mm diameter cast iron bend with cleaning eye No. 22.60
G013 50mm diameter equal or unequal cast iron junction or No. 11.90
tee with cleaning eye.
G014 75mm diameter equal or unequal cast iron junction or No. 15.50
tee with cleaning eye.
G015 100mm diameter equal or unequal cast iron junction No. 17.90
or tee with cleaning eye
G016 150mm diameter equal or unequal cast iron junction No. 37.40
or tee with cleaning eye
G017 75mm to 50mm diameter cast iron reducer. No. 12.00
G020 100mm diameter short length cast iron pipes with No. 14.10
cleaning eye not exceeding 300mm in length
G021 150mm diameter short length cast iron pipes with No. 21.40
cleaning eye not exceeding 300mm in length
G022 Steel blot for cast iron inspection covers. No. 0.60
G023 Cast iron cover plate to cleaning eye including all No. 3.10
necessary bolts etc to 50mm diameter pipe, bend,
etc.
G024 Cast iron cover plate to cleaning eye including all No. 3.40
necessary bolts etc to 75mm diameter pipe, bend,
etc.
G025 Cast iron cover plate to cleaning eye including all No. 3.50
necessary bolts etc to 100mm diameter pipe, bend,
etc.
G025 Cast iron cover plate to cleaning eye including all No. 3.70
necessary bolts etc to 150mm diameter pipe, bend,
etc.
G027 Cast iron heavy duty 100mm diameter “duck” foot No. 72.10
bend including breaking up concrete floor.
G028 100mm diameter cast iron heavy duty union socket No. 24.50
for underground pipes
G029 Cast iron downspout outlet fixed to 75mm diameter No. 18.80
cast iron pipe with three numbers of tightening bolts
G030 225mm X 450mm cast iron purpose made street No. 149.80
gully with 100mm outlet including connection, all
necessary excavation and concrete surround.
G031 100mm diameter cast iron coupling joint including all No. 174.10
necessary bolts and nuts
SOR Page 11
Fittings
H004 80mm diameter bends 300mm ling including making No. 33.10
necessary extra joints (with cleaning eye)
H006 Extra over for bolted flange joints including all Joint 7.10
necessary drilling, bolts and gaskets (For items
H001; H004 & H005)
H011 Extra over for bolted flange joints including all Joint 15.50
necessary drilling bolts and gaskets (For items H002;
H009 & H010)
H012 100mm diameter double flanged “duck” foot bend No. 48.00
H022 215mm diameter flange washer for water mains. No. 8.20
H028 Extra over for bolted flange joints including all Joint 30.80
necessary drilling bolts and gaskets. (For items
H003; H025 & H026)
6.30
H029 Cement lining for 100mm diameter ductile iron fitting No.
H030 Cement lining for 150mm diameter ductile iron fitting No. 7.20
H031 100 X 50m ductile iron cement lined flange tee No. 61.70
H035 80mm diameter ductile iron cement lined heavy duty m 31.30
pipes (push-on Joint “T” type or Mechanical Joint
accessories and flexible joints laid in trench (trench
and concrete bed measured separately)
H038 Extra over ductile iron pipe for 80mm diameter bend m 16.50
(all angles)
H039 Extra over ductile iron pipe for 100 diameter bend (all m 19.40
angles)
SOR Page 13
Fittings
J004 Extra over 100mm diameter pipe for bend (SS 272) No. 3.20
J005 Extra over 150mm diameter pipe for bend (SS 272) No. 5.90
J006 Extra over 200mm diameter pipe for bend (SS 272) No. 46.60
J018 275 X 120 X 5mm thick rectangular pipe (SS 272 m 48.70
SOR Page 17
J021 50mm sweep junction (SS 213) without inspection No. 3.70
opening
J022 75mm sweep junction (SS 213) without inspection No. 6.90
opening
J023 100mm sweep junction (SS 213) without inspection No. 9.10
opening
J024 150mm sweep junction (SS 213) without inspection No. 15.10
opening
J026 100 X 50mm sweep junctions (SS 213) without No. 5.30
inspection opening
J027 100 X 75mm sweep junctions (SS 213) without No. 6.10
inspection opening
J034 100 X 100 X 100mm double sweep junction without No. 10.20
inspection opening (SS 213)
J035 150 X 100 X 100 reducing sweep junction with No. 26.10
inspection opening (SS 213)
J036 150 X 150 X 100 reducing sweep junction with No. 49.60
inspection opening (SS 213)
SOR Page 18
J047 32mm Bend (any Angles) and Elbow (SS 213) plain No. 2.40
(Inspection opening including access cap measured
separately)
J048 40mm Bend (any Angles) and Elbow (SS 213) plain No. 2.80
(Inspection opening including access cap measured
separately)
J049 50mm Bend (any Angles) and Elbow (SS 213) plain No. 2.40
(Inspection opening including access cap measured
separately)
J050 75mm Bend (Any Angles) and Elbow (SS 213) plain No. 4.00
(Inspection opening including access cap measured
separately)
J051 100mm Bend (Any Angles) and Elbow (SS 213) plain No. 3.70
(Inspection opening including access cap measured
separately)
J052 150mm Bend (Any Angles) and Elbow (SS 213) plain No. 6.20
(Inspection opening including access cap measured
separately)
J053 120 X 275mm rectangular elbow (SS 272) plain No. 142.90
(Inspection opening including access cap measured
separately)
SOR Page 19
J057 150 X 100mm level invert reducers (SS 213) No. 11.70
J058 100 X 75mm level invert reducers (SS 213) No. 7.80
J059 100 X 50mm level invert reducers (SS 213) No. 6.70
J063 200mm diameter X 275 X 120mm adaptor (SS 272) No. 141.10
J067 Extra over UPVC fitting (various sizes) for inspection No. 7.40
opening (cleaning eye) including access cap
J068 75m diameter UPVC socket (Screw-on type) for SS No. 4.50
213 pipe
J069 100mm diameter UPVC socket (Screw-on type) for No. 5.00
SS 213 pipe
J071 150mm diameter access cap with screw to UPVC No. 4.00
pipes
J073 100 diameter UPVC vent cowl to vent pipe No. 4.80
SOR Page 20
J074 Steel collar bracket with hop dip for UPVC soil/ waste No. 4.80
pipes 75mm diameter for SS 141 pipe
J077 Steel collar bracket with hop dip for UPVCsoil/waste No. 6.10
pipes 75mm diameter for SS141 pipe.
J080 150mm diameter UPVC U-trap body for rooftop vent No. 14.50
pipe (SS 213)
J093 48mm diameter spigot adaptor for existing 50mm No. 18.10
cast iron pipe
J094 72mm diameter spigot adaptor for existing 80mm No. 26.90
cast iron pipe
J095 65mm diameter spigot adaptor for existing 80mm No. 26.90
cast iron vent pipe
J096 95mm or 96mm diameter spigot adaptor for existing No. 26.50
100mm cast iron pipe
J097 96mm diameter spigot adaptor for existing 100mm No. 29.50
cast iron ‘S’ Bend
J099 95mm diameter Pan Collar Adaptor for existing No. 28.20
100mm diameter cast iron pipe
J100 148mm diameter spigot adaptor for existing 150mm No. 39.60
cast iron pipe
J101 95mm diameter grating adaptor for existing 100mm No. 33.30
diameter cast-iron pipe with one/two side inlets
irrespective of size
J102 117mm diameter grating adaptor for existing 125mm No. 34.50
diameter cast-iron pipe with one/two side inlets
irrespective of size
J103 Rubber ring 50mm diameter w.c. straight connector No. 16.80
with spigot not exceeding 100mm long
J104 Rubber ring 80mm diameter w.c. straight connector No. 18.10
with spigot not exceeding 100mm long
J105 Rubber ring 100mm diameter w.c. straight connector No. 19.40
with spigot not exceeding 100mm long
J106 Rubber ring 100mm diameter w.c. straight connector No. 24.40
with spigot exceeding 100mm but not exceeding
150mm long
SOR Page 22
J108 Rubber ring 125m diameter w.c. straight connector No. 26.90
with spigot exceeding 100mm but not exceeding
150mm long
J109 Rubber ring 150mm, diameter w.c. straight connector No. 27.50
with spigot not exceeding 100mm long
J150 15mm Bend (any Angles) and Elbow (SS 141) No. 2.20
J151 20mm Bend (any Angles) and Elbow (SS 141) No. 2.20
J152 25mm Bend (any Angles) and Elbow (SS 141) No. 2.40
J153 32mm Bend (any Angles) and Elbow (SS 141) No. 3.20
SOR Page 24
J155 50mm Bend (any Angles) and Elbow (SS 141) No. 5.90
J156 75mm Bend (any Angles) and Elbow (SS 141) No. 15.10
Faucet Socket
Saddle Clip
Copper Pipe
Elbows
K012 15mm diameter Elbows No. 3.90
SOR Page 27
Coupling
Union
Tee
SOR Page 28
Reducing Elbow
Coupling Washer
Fireclay Sink
L001 600 X 450 X 200mm white fireclay sink complete with No. 113.00
cantilever brackets, 40mm vulcanite plug and chain,
all necessary trap, waste pipe and fittings.
L002 685 X 450 X 250mm white fireclay sink complete with No. 131.40
cantilever brackets, 40mm vulcanite plug and chain,
all necessary trap, waste pipe and fittings.
L003 600 X 450 X 250mm white fireclay sink complete with No. 96.50
40mm vulcanite plug and chain, all necessary trap,
waste pipe and fittings.
L004 685 X 450 X 250mm white fireclay sink complete with No. 114.80
40mm vulcanite plug and chain, all necessary trap,
waste pipe and fittings.
L006 500 X 400mm coloured vitreous China locally made No. 102.50
wash hand basin complete with pillar tap (push
button spring type) cantilever brackets, vulcanite plug
and chain, all necessary trap, waste pipe and fittings.
L007 500 X 400mm coloured with pedestal stand vitreous No. 152.20
China locally made wash hand basin complete with
pillar tap (push button spring type) cantilever
brackets, vulcanite plug and chain, all necessary
trap, waste pipe and fittings.
L008 500 X 400mm white vitreous China locally made No. 137.40
wash hand basin complete with pillar tap (delay
action type) cantilever brackets, vulcanite plug and
chain, all necessary trap, waste pipe and fittings
L009 500 X 400mm coloured vitreous China locally made No. 146.10
wash hand basin complete with pillar tap (delay
action type) cantilever brackets, vulcanite plug and
chain, all necessary trap, waste pipe and fittings
L010 500 X 400mm coloured with pedestal stand vitreous No. 195.80
China locally made wash hand basin complete with
pillar tap (delay action type) cantilever brackets,
vulcanite plug and chain, all necessary trap, waste
pipe and fittings.
SOR Page 31
L012 550 X 450mm stainless steel wash hand basin No. 57.40
complete with pillar tap, cantilever brackets, vulcanite
plug and chain, all necessary trap, waste pipe and
fittings.
Sink
L013 1000 X 500mm single bowl single drainer S.W.G. No. 111.30
2.03mm anodised aluminium sink complete with
cantilever brackets 40mm vulcanite plug and chain,
all necessary trap, waste pipe and fittings.
L014 1500 X 500mm single bowl single drainer S.W.G. No. 142.80
2.03mm anodised aluminium sink complete with
cantilever brackets 40mm vulcanite plug and chain,
all necessary trap, waste pipe and fittings.
L015 1067 X 457mm single bowl, single drainer stainless No. 125.20
steel sink complete with cantilever brackets 40mm
vulcanite plug and chain, all necessary trap, waste
pipe and fittings.
L016 1500 X 500mm locally made single bowl double No. 182.60
drainer stainless steel sink complete with cantilever
brackets 40mm vulcanite plug and cabin, all
necessary trap, waste pipe and fittings.
L017 1500 X 500mm locally made double bowl double No. 217.00
drainer stainless steel sink complete with cantilever
brackets 40mm vulcanite plug and cabin, all
necessary trap, waste pipe and fittings.
Waste Trap
L018 32mm galvanised wrought iron ‘S’ trap for lavatory No. 7.00
basin
L019 40mm galvanised wrought iron ‘S’ trap for sink No. 7.30
L028. 100mm UPVC adjustable ‘P’ trap complete with No. 12.40
hopper and vent with grating including jointing to
waste pipe
Waste Fitting
L029 Brass waste fitting to sink or basin complete with Set 7.20
brass cobweb grating, cabin and plug
L030 Brass waste fitting to sink or basin complete with No. 5.30
brass cobweb grating only
Bottle Trap
L035 UPVC pipe, for sink waste including elbow and bend No. 11.00
L036 Vulcanite plug complete with chain for sink or basin No. 3.30
L037 5mm diameter X 75mm long brass grid screw to sink No. 1.40
L039 ‘Presto” No. 605 or other approved wash basin delay No. 217.50
action tap.
L044 White earthenware pedestal w.c. pan only complete No. 105.00
with plastic seat and trap with or without vent
L045 PVC screw cap supplied and fixed for vent of w.c. No. 4.10
squat/pedestal pan
L046 Plastic w.c. seat complete with cover. (Heavy duty No. 34.40
with any colour)
L047 Plastic w.c. seat but without cover. (Heavy duty with No. 25.60
any colour)
L048 Rubber cone for joint between flush pipe and back No. 3.10
inlet of w.c. pedestal pan.
L052 Surfaced mounted chromium plated toilet roll holder No. 14.50
with plastic roller fixed or plugged to wall.
L053 Surfaced mounted plastic toilet roll holder with plastic No. 12.70
roller fixed or plugged to wall.
L054 Approved plastic roller fixed in existing toilet roll No. 0.90
holder brackets.
Urinal
L055 White vitreous China wall hung urinal bowl No. 69.50
L056 White glazed urinal slabs 600mm wide X 1050mm No. 501.20
high
L057 White glazed urinal return end slab 1050mm high to No. 222.70
match existing
SOR Page 34
L070 Urinal concealed flush valve with 16mm diameter ‘L’ No. 148.10
shape flushing pipe, front cap cover, but without spud
L071 Urinal concealed flush valve with 16mm diameter ‘L’ No. 150.40
shape flushing pipe, front cap cover, but with spud
L072 PUB approved stainless steel sensor operated flush No. 302.00
valve complete with stainless steel outlet flush pipes
to urinals including fixing and jointing to water supply
and fittings as specified
Cistern
L073 14 litres high level bakelite cistern only, complete No. 99.90
with chain, rubber pull and brackets
L074 9/4.5 litres dual action approved high level plastic No. 45.00
cistern complete with nylon cord; plastic pull and
brackets
SOR Page 35
L076 14 litres low-level bakelite cistern only complete with No. 117.90
flush bend, actuating lever handle and cantilever
brackets.
L077 9/4.5 litres dual action approved low level plastic No. 62.80
cistern complete with flush bend, actuating lever
handle and cantilever brackets
L078 White glazed vitreous clay cover to w.c. cistern No. 10.20
L081 Brass chain and rubber pull for high level cistern No. 6.90
L083 Brass nut for flush pipe to w.c. cistern outlet No. 5.40
connection’
L084 Chromium plated lever handle to low level w.c. No. 9.70
cistern
L088 Plastic flush arm holder with nylon rope to w.c. No. 3.70
cistern
L090 Plastic nut for flush pipe to w.c. cistern outlet No. 4.20
connection.
L091 P.V.C. flush pipe not exceeding 2.0m long bend to No. 5.60
high level cistern
L092 P.V.C. flush pipe exceeding 2.0m but not exceeding No. 7.30
3.0m long bent to high level cistern.
L093 40mm PVC flush pipe to low level cistern. No. 4.30
SOR Page 36
L099 Galvanised iron cistern chain and pull for high level No. 69.20
cistern
L100 Cast iron brackets for draining boards, sinks, basins No. 7.80
or cisterns including cutting and pinning to walls.
L101 Light gauge metal flexible inlet tube 13mm diameter No. 4.10
to cisterns/ basins and taps complete with
connectors.
Mirror
L103 150 X 150mm white glazed recessed type soap tray No. 13.50
embedded in cement mortar including hacking off
existing and make good tile surround to match
L104 108mm X 108mm white glazed recessed type soap No. 15.90
try embedded in cement mortar
L105 20H 18-8 Type 304 stainless steel rectangular liquid No. 43.80
soap dispenser or other approve of 1.2 litre capacity
equipped with acrylic soap level window exposed
surface stain-finished completed with vandal
resistant mounting bracket and separate concealed
wallplate.
L106 Horizontal all purposed valve (Model CV-02SA) for No. 9.90
stainless steel liquid soap dispenser constructed of
chrome plated brass with Buna-N “O” ring markings
with engineering plastic moving parts and push-in
type valve projecting 61mm.
L110 Long bath trap complete with waste fittings and No. 19.20
overflow pipes.
Hand Dryer
SOR Page 37
L112 25mm diameter stainless steel pipe clamp with No. 23.70
rubber lining for emergency use on pipe burst
L113 32mm diameter stainless steel pipe clamp with No. 26.00
rubber lining for emergency use on pipe burst
L114 40mm diameter stainless steel pipe clamp with No. 28.30
rubber lining for emergency use on pipe burst
L115 50mm diameter stainless steel pipe clamp with No. 34.00
rubber lining for emergency use on pipe burst
L116 100mm diameter stainless steel pipe clamp with No. 122.80
rubber lining for emergency use on pipe burst
L117 150mm diameter stainless steel pipe clamp with No. 139.20
rubber lining for emergency use on pipe burst
L119 30mm diameter C.P. copper flush pipes including all No. 13.70
necessary tees and brackets for each chute
Stop Cock
M001 13mm DZR type brass screw down stop cock No. 11.30
M002 20mm DZR type brass screw down stop cock No. 18.90.
M003 25mm DZR type brass screw down stop cock No. 29.70
M004 32mm DZR type brass screw down stop cock No. 68.60
M005 40mm DZR type brass screw down stop cock No. 82.90
M006 50mm DZR type brass screw down stop cock No. 113.90
Bib Tap
M008 13mm brass bib key tap with spigot nozzle including No. 10.50
portable spindle head
M009 13mm “DZR type” brass high pressure screw down No. 13.90
bib tap with a hole drilled through the spindle
M010 13mm brass bib key tap including portable spindle No. 9.90
head
M011 13mm brass bib tap with spigot nozzle and locking No. 15.65
eye
M012 13mm “DZR type” brass high pressure screw down No. 11.50
bib tap
M014 13mm garden bib tap with spigot nozzle No. 11.40
M017 15mm chromium plated pillar tap with swivel swan No. 21.70
neck
M019 20mm “DZR type” brass high pressure screw down No. 14.40
bib tap
M020 20mm chromium plated brass bib tap No. 15.20
M021 20mm garden bib tap with spigot nozzle No. 21.60
SOR Page 39
Gland Nut
M023 Gland nut for 13mm stop cock/bib tap No. 2.80
M024 Gland nut for 20mm stop cock/bib tap No. 2.80
M025 Gland nut for 25mm stop cock/bib tap No. 2.90
M026 Gland nut for 21mm stop cock/bib tap No. 2.90
M027 Gland nut for 40mm stop cock/bib tap No. 3.20
M028 Gland nut for 50mm stop cock/bib tap No. 3.60
Rubber Washer
M029 Rubber washer for 13mm to 25mm stop cock or bib No. 1.30
tap in replacement
M030 Rubber washer for 30mm to 50mm stop cock or bib No. 1.40
tap ion replacement
Gate Valve
M039 80mm diameter cast iron gate valve in replacement No. 97.60
including washers, gaskets, bolts and nuts
M040 100mm diameter cast iron gate valve in replacement No. 120.40
including washers, gaskets, bolts and nuts
M041 50mm diameter “DZR type” brass gate valve in No. 33.10
replacement including washers, gaskets, bolts and
nuts
SOR Page 40
M042 40mm diameter “DZR type” brass ball valve No. 38.90
M043 Lever stem to 50mm diameter equilibrium ball float No. 13.50
valve
Sluice Valve
M044 150mm diameter cast iron sluice valve with flanged No. 261.70
ends and wheel head
M045 63mm diameter fire dry main landing valve (The No. 96.00
valve shall be constructed in good gunmetal,
screwed or flanged for attachment to the dry riser
main and fitted with a 63mm. Instantaneous female
coupling with a removable blank cap screwed by a
suitable length of chain).
M046 Approved dry riser inlet brass valves consisting of 4 No. 365.50
inlets, each consisting of a 63mm instantaneous
male coupling (British “B” type), a back pressure
valve and protected by a cap screwed with a suitable
length of chain.
M047 Brass chain for dry riser blank cap No. 6.30
M048 Brass cap with chain for dry riser main No. 20.70
M049 Gunmental hand wheel for dry riser landing valve No. 15.20
marked with ‘OPEN’ and ‘SHUT’ directions including
all necessary nuts and washers.
M050 19/25mm diameter jet spray nozzle with ON/OFF No. 27.40
handle
M051 Approved automatic air release valve 25mm for dry No. 22.20
riser main
M052 Approved canvas /nylon belt with key-alike padlocks No. 6.80
for strap locking handwheels in closed position
M054 Exposed water closet flush valve with 280mm long No. 148.10
supply pipe, vacuum breaker and stop valve for top
inlet water closet bowl
M055 Water closet water-saving flush valve with 470 X No. 153.90
320mm long ‘T’ flush pipe, vacuum breaker and stop
valve
SOR Page 41
M057 Water closet concealed flush vale with flushing pipe No. 148.10
and 32mm diameter elbow coupling
M058 Water closet water-saving concealed flush valve with No. 217.10
flushing pipe and 32mm diameter elbow coupling
M059 PUB approved stainless steel sensor operated flush No. 426.70
valve complete with stainless steel outlet flush pipes
to water closets including fixing and jointing to water
supply and fittings as specified
M060 Miniature stop valves for basin and cistern No. 9.10
Flow Regulator
Rubber Hose
Floor Trap
N002 Cast iron deep seal floor trap complete with hinged No. 77.50
grating cast iron hopper and with vertical side or back
inlets and 75mm outgo pipe including hacking
existing damaged trap and jointing to existing pipe.
N003 150mm cast iron hopper connecting piece not No. 13.20
exceeding 300mm long including hacking existing
hopper and all necessary jointing to pipe.
N004 100mm diameter cast iron floor trap or floor waste No. 54.20
with hinged grating, hopper and 75mm outgo and
concrete surround (at ground floor slab) including
hacking to remove existing damaged trap/waste and
jointing to pipe.
N005 150mm diameter cast iron floor trap with hinged No. 71.00
grating, hopper and 100mm diameter outgo and
concrete surround (at ground floor slab) including
hacking to remove existing damage trap and jointing
to pipe.
N010 150mm Chromium plated hinged grating for floor trap No. 7.10
N011 8mm thick 150mm cast iron square hinged/frame No. 4.70
grating to apron gulley
Plastic Grating
N019 150mm square with 100mm diameter plastic hinged No. 3.20
grating for floor trap including setting in concrete.
Dome-Shaped Grating
Vertical Grating
N023 100mm diameter vertical cast iron grating with No. 40.80
115mm outgo for rainwater down pipe outlet
including hacking and setting in cement mortar
N024 Purpose made mild steel vertical grating to 75mm No. 18.65
diameter rainwater down pipe outlet including
embedding in floor slab and makes good all
disturbed area.
N025 75mm diameter cast iron dome grating including No. 14.90
embedding in cement mortar
N026 100mm diameter cast iron dome grating including No. 16.20
embedding in cement mortar
N027 150mm diameter cast iron dome grating including No, 20.40
embedding in cement mortar
SOR Page 44
N028 Purpose made perforated 18G aluminium strainer for No. 84.00
street gulley trap excluding cast iron grating (Not
exceeding 300mm diameter)
N029 Purpose made perforated 18G aluminium strainer for No. 92.10
street gulley trap excluding cast iron grating
(Exceeding 300mm but not exceeding 450mm
diameter)
N031 100mm diameter ductile iron ‘Y’ – pattern trap No. 245.30
including flanges and cutting removing existing pipe
etc
Anti-Mosquito Device
N033 Anti mosquito device (98mm) with body; filter; cover No. 5.60
and gully trap grating
N034 Anti-mosquito device (98mm) with body; filter and No. 2.40
cover only
Screw on Grating
N038 150mm square or round UPVC heavy duty floor trap SET 10.65
grating
N039 150mm chrome plated alloy steel floor trap grating No. 23.00
N040 75mm diameter UPVC dome grating with square No. 3.75
base
N041 100mm diameter UPVC dome grating with square No. 4.95
base
N042 150mm diameter UPVC dome grating with square No. 5.40
base
SOR Page 45
N051 Auto floating ball cover fitting c/w lightweight PVC No. 7.50
ball
P001 Re-caulk joints of 75mm diameter cast iron pipes soil No. 5.80
or waste pipes including raking out and providing
additional molten lead and spun yarn if required.
P002 Re-caulk joint of 100mm diameter cast iron pipes soil No. 7.20
or waste pipes including raking out and providing
additional molten lead and spun yarn if required.
P003 Re-caulk joint of 150mm diameter cast iron pipes soil No. 8.50
or waste pipes including raking out and providing
additional molten lead and spun yarn if required
P004 Re-caulk joints of 100mm diameter cast iron rising No. 7.30
main pipe including raking out and providing
additional spun yarn and molten lead if required in
upright position
P005 Re-caulk joints of 100mm diameter cast iron rising No. 6.60
main pipe on level ground including raking out and
providing additional spun yarn and molten lead if
required.
P006 Re-caulk joints of 150mm diameter cast iron rising No. 7.80
main pipe including raking out and providing
additional spun yarn and molten lead if required in
upright position.
P007 Re-caulk joints of 150mm diameter cast iron rising No. 7.30
main pipe on level ground including raking out and
providing additional spun yarn and molten lead if
required.
P008 Cut 100mm diameter cast iron rising mains and No. 35.30
jointing with Gilbault coupling
P009 Cut 150mm diameter cast iron rising mains and No. 45.70
jointing with Gilbault coupling
P011 Repair leaking joints of galvanised service pipes not No. 2.60
exceeding 25mm diameter.
P012 Repair leaking joints of galvanised service pipes No. 3.20
exceeding 25mm diameter but not exceeding 50mm
diameter
SOR Page 47
P015 Cut off existing galvanised pipes, threads end and No. 3.90
prepare for connection to new pipes.
P019 Bore holes in water services pipes for use as bin Job 4.40
chute sparge pipes at 50mm centre to centre (per
chute)
P020 Take down copper inlet pipe to w.c. cistern for Job 4.80
clearing and roddng including refixing to position and
make good work disturbed.
Repair to WC
P022 Hack hole through wall or floor slabs not exceeding Job 14.00
150mm thick to form chase for entry of water service
pipes (measured separately if such job is required)
P025 Clear obstruction in floor traps, gulley traps and Choke 2.30
urinal traps.
P026 Clear obstructions in w.c. pan Choke 6.60
P034 Pump up and remove oil waste from oil interceptors No. 19.20
in industrial workshops
P035 Flush the 100mm diameter ductile iron ‘Y’ pattern No. 3.30
trap
P036 Clear waste and sludge from oil interceptors in Drum 39.90
industrial estates collected in metal drum (209
litres/46 gallons) and cart away to ENV’s dumping
ground in accordance with ENV’s requirement and all
necessary expenditure/fees.
P037 Repair 80mm to 100mm cast iron gate valve leakage No. 17.90
including renewing gaskets
P040 Adjust stop cocks to tilt towards any direction Job 2.40
specified including making good any damaged or
affected piping work.
P041 Clean white glazed w.c. pans or other white glazed Job 5.20
sanitary fittings to a satisfactory finish free from stain.
P045 Repair leaking joints of UPVC pipe from 50mm No. 5.20
diameter to 150mm diameter
P046 Repair leaking joint of dry raiser pipe to comply with No. 16.90
Building Control and Fire Brigade regulation and
tested.
Locking Device
P047 Electro galvanised steel locking device for Civil No. 24.40
Defence tap, 180 X 110 X 150mm for taps in void
decks with all accessories.
P048 Electro galvanised steel locking device for Civil No. 27.20
Defence tap, 200 X 170 X 195mm for taps in void
decks with all accessories.
P052 200 X 200 X 150mm 16 gauge mild steel box with No. 40.90
electro-galvanised coated with 1 coat of epoxy baked
powder coated paint c/w locking device.
Miscellaneous Repairs
P057 Seal up sand holes in cast iron pipes with metallic No. 5.10
epoxy resin as per manufacturer’s instruction
including touching up paint to match existing
P059 Clean urinal range, remove existing cement pointing Job 21.10
between slab/channels etc and repaint with white
cement.
P060 Supply labour and equipment for locating leakage Test 161.00
test in underground pipe.
P062 Repair leaking cast iron pipe at joint of UPVC pipe Joint 6.40
exceeding 75mm but not exceeding 150mm diameter
P063 Replace lock only to tap box of refuse chute flushing No. 13.80
system & civil defence tap to match existing.
P064 Break up existing long bath wall to form opening of Job 41.20
size equivalent to 4 nos. of wall tiles, complete with
precast door, finish with glazed wall tiles to match
existing including carting away of debris.
P065 Break up displaced stool support or water mains and No. 11.20
provide new 305mm X 305mm brick stool support not
exceeding 380mm high including rendering sides and
haunching top in cement mortar (1:3)
P066 Repair leak in concrete surround of gulley trap, cast Job 3.60
iron soil pipes, etc. with waterproofed cement mortar.
P069 Hack out existing point at joint between sink and wall Job 3.00
and repaint in white cement.
P070 Hack out existing pointing at joint between long bath Job 9.90
and wall and repaint in white cement.
P071 Form 75mm high cement surround at base of w.c. Job 2.90
cistern flush-pipe and squat pan joint to cure leak.
SOR Page 51
Q002 Clear, flush with water, clean, including scrape Job 3.30
hardened oil sludge, debris etc, off sewer lines using
high pressure water jetting and electro-mechanical
equipment with minimum discharge pressure of 4000
PSI and vacuum cleaning equipment (Including main
and branch half round channels within inspection
chambers)
Q003 Clear, flush with water, clean, including scrape Job 5.10
hardened oil sludge, debris, etc off street gulleys and
strainers
Q004 Clear, flush with water, clean, including scrape Job 134.10
hardened oil sludge, debris etc, off grease trap/
interceptor using high pressure water jetting and
electro-mechanical equipment with minimum
discharge pressure of 4000 PSI including vacuum
cleaning of solids and semi solids
R003 100mm diameter galvanised steel spring clip with No. 3.40
nylon nettings cover at outlet of overflow pipe.
R007 Seal up gaps along edges between covers and tanks m2 1.10
with new nylon mosquito mesh of approved quality
with approved non-toxic sealing compound
R013 Approved inspection cover to mild steel water tank to No. 34.60
match existing
SOR Page 53
R017 100mm galvanised iron Dam nut complete with No. 8.40
washer, etc. to water tank
R019 Repair leakage at jamb nut including flushing out No. 15.90
water if necessary and tightening jamb nut.
R020 Dismantle and remove from site existing damaged Cover 50.90
inspection cover including the 150mm high four-sided
galvanised steel boxing to the access hole and
replace with 0.559mm thick galvanised steel cover
overall size 490 X 490mm including boxing up the
access hole with 150mm high X 0.559 thick
galvanised steel including pop-riveting
R022 100mm diameter PVC cap with 100mm diameter Job 27.00
(UPVC) bend (any angles )or elbow (SS 213) plain
and a 100mm diameter testing openings (F&F)
including removal of existing nylon netting and drill
holes of different sizes to PVC cap and providing on
allan type screw.
R023 Prepare, sand and remove rust, stains and other m2 0.40
sediments from internal sides and bottom of tanks,
flush and clean surfaces, including bracing to
stainless steel water tank
R024 Prepare, remove all rust, stains and other sediments m2 0.30
from internal sides and bottom of tanks, flush and
clean surfaces to FRP/GRP or Reinforced concrete
storage or suction tanks, including flushing and
refilling tanks upon completion and including flushing
and refilling tanks upon completion
R025 Flush suction/storage tanks and refilling with clean No. of Tank 3.30
water upon completion (this item is used where
washing of tank is not required
R029 Clean and remove rust stains from external surface m2 0.35
of stainless steel water tanks
R030 Flush steel strainer located after PUB Bulk Meter No. 6.10
including dismantling and refixing
S001 13mm diameter light gauge metal flexible inlet tube No. 3.00
to cistern/basins and taps complete with connectors.
S002 13mm rubber washer to tap and stop cock. No. 0.40
S012 13mm diameter ‘DZR type’ brass stop cock. No. 8.40
S013 13mm diameter ‘DZR type’ high pressure brass No. 8.40
screw down bib tap
S014 13mm diameter copper piping 300mm long with No. 3.30
connectors at both ends for fittings
S016 2mm thick 150mm diameter galvanised steel square No. 3.45
hinged with/without perforated grating for apron gully
S018 13mm brass bib key tap including portable spindle No. 7.50
head
SOR Page 56
T002 Deck mounted stainless steel liquid soap dispenser No. 47.80
T003 Take out existing ball valve in tank and remove off No. 25.50
site
T004 Supply and install 40mm PUB approved water meter No. 332.50
(flanged type)
T005 Supply and install 50mm PUB approved water meter No. 342.00
(flanged type)
T007 Fibreglass water storage tank not exceeding 1000 No. 313.50
litres nominal capacity, supported by 3 pieces 38 X
75mm twice creosoted timber battens and cover of
flat shape with beaded edges lined down and with all
edges bolted and jointed with stainless steel bolts
T008 Fibreglass water storage tank not exceeding 2000 No. 332.50
litres nominal capacity, supported by 3 pieces 38 X
75mm twice creosoted timber battens and cover of
flat shape with beaded edges lined down and with all
edges bolted and jointed with stainless steel bolts
T009 Fibreglass water storage tank not exceeding 3000 No. 427.50
litres nominal capacity, supported by 3 pieces 38 X
75mm twice creosoted timber battens and cover of
flat shape with beaded edges lined down and with all
edges bolted and jointed with stainless steel bolts
T010 Fibreglass water storage tank not exceeding 4000 No. 323.00
litres nominal capacity, supported by 3 pieces 38 X
75mm twice creosoted timber battens and cover of
flat shape with beaded edges lined down and with all
edges bolted and jointed with stainless steel bolts
T011 Take out existing basin or sink of any size including No. 12.75
brackets, disconnect pipes, etc and set aside for
reuse and make good all work disturbed
T012 Take out existing basin or sink of any size including No. 16.55
brackets, disconnect pipes, etc and set aside for
reuse and make good all work disturbed and remove
to store or off site.
T013 Refix existing basin or sink in new position including No. 31.55
cutting and pinning brackets, diverting, altering and
adjusting water services, waste pipes, etc and make
good all work disturbed including additional piping
required
T014 Add for each addition 1.50m or part thereof No. 16.35
SOR Page 57
U013 Casing c/w front cover, back cover & screws No. 64.60
U016 Solenoid assy c/w valve coil, plug, rubber, washer, No. 81.40
screw (E-Ring)
U020 AC adaptor assy c/w earth cable, connector & No. 86.40
screws
U022 Push button assy c/w cap wit Hexagonal nut & switch No. 34.20
SSOR Page 1
V008 Stopcock assy c/w handle, ‘O’ ring stopcock cap, ‘O’ No. 124.60
ring, seal check valve and rubber washer
V015 Flush valve assy (Body, 101 ring, adaptor and No. 56.40
handle cap
V019 Vacuum breaker assy c/w rubber washer outlet No. 56.40
piping rubber washer & outlet piping nut
V023 Solenoid assy c/w valve, coil, plug, rubber washer, No. 94.20
screw & E-ring
V024 Elbow Adaptor (90 degree street, T-Elbow) No. 13.20
V027 AC adaptor with controller board assy c/w earth No. 74.60
wire, connector & screws
V029 Push button assy c/w, cap nut, hexagonal nut & No. 34.20
switch
V035 Supply and fix 15mm chromium plated brass 2-way No. 73.10
bib tap (lever type) including all necessary
accessories for fixing and jointing to pipe works
V036 13mm diameter blots, nuts and washers for flange No. 2.00
joint or outer fitting
V037 17mm wide punched steel for hanging cast iron pipe No. 6.20
etc (Band not exceeding 1.0 meter long)