HFL SCOUR DEPTH RBL L1 Input Data Load factor FL FL 1.5 Diameter of pile D D 500 mm Pile capacity in compression P P 740 kN Pile capacity in Tension T Tc 480 kN Pile capacity in Lateral H Hc 100 kN Grade of concrete fck fck 25 N/mm^2 Grade of steel fy fy 500 N/mm^2 Clear cover c c 60 mm Minimum % of steel required pt,min pt 0.4 % Diameter of circular tie reinforcement t t 8 mm Min. diameter main reinforcement 1 1 16 mm Max diameter of main reinforcement 2 2 25 mm Area of pile cross section Ac Ac 196349.5 mm^2 ( b is the equivalent side of a square) b 443.1 mm Length of pile below cut off level L1 20000 mm Depth of Fixity calculation (As per Appendix C, Cl. C-1.2) Coe. of stiffness K1 inkg/cm (From Table 1 of IS 2911, Part1) K1 0.26 kg/mm Length of pile above GL, L1 L1 0 Modulus of Elasticity of Conc. E = 5000fck Ec 25000 N/mm 254842.0 Moment of inertia of pile I = D 4 / 64 I 306796.2 cm Pile Stiffness T = (E I /K1 )^1/5 T 197.5 cm L1 / T = 0.00 L1/T 0 As Fixed head pile Lf / T (From Fig 2 of IS 2911, Part1 Sec.2) Lf/T 2.2 Length of Fixity Lf Lf 434.6 cm Design of pile from cut off level to depth of fixity Factored Lateral load Hu Hu 111 kN Factored Bending moment Mu = Hu(L1+Lf)/2 For fixed head pile Mu 241.2 kNm Reduction factor = 0.83 (From Fig 3 - IS 2911, Part 1 Sec.2) Rf 0.83 Design Bending moment Mu Mu(d) 200.2 kNm Effective cover d' d' 72.5 mm d' / D = d'/D 0.145 Design for Compression with Bending Slenderness ratio=(leff/D) Leff/D 10.43 <12 short col. Minimum eccentricity =(Lf/500)+(D/30) 25.36 mm 0.05D 25 mm Factored compressive load Pu Pu 1110 kN Pu/fck*D*D Pu/fck*D^2 0.1776 Mu/fckD^3 Mu/fck*D^3 0.064 Refer Chart 57 of SP:16 pt/fck 0.025 percentage of steel, pt pt 0.63 % Area of steel required Ast required Ast 1227.2 mm^2 Design for Bending only Factored compressive load Pu Pu 0 kN Pu/fckD2 = 0 Pu/fck*D^2 0 Mu/fckD^3 Mu/fck*D^3 0.064 Refer Chart 57 of SP:16 for pt/fck pt/fck 0.065 pt pt 1.625 Area of steel required Ast Ast 3190.7 mm Provide 7 Nos 25 dia 7 25 mm Ast provided Ast provided 3436 OK Design of pile below depth of fixity Vertical Compression Factored compressive load Pu = 1500 kN Pu 1110 kN Axial capacity Pa,u = 0.4 fck Ac Pa 1963.5 kN OK Vertical Uplift (Tension): Factored Tensile load Tu = Tu 0 kN Area of steel required Ast,req = Tu / 0.87 * fy Ast 0.0 mm^2 Provide 7 Nos 16 dia + 0 Nos 0 dia 7 16 mm Ast provided 1407 OK HENCE PROVIDE 7 No. - Y25 Dia REBARS TO A DEPTH OF 6250MM FROM CUT OFF LEVEL AND PROVIDE 7 No. - Y16 DIA. BARS FOR BALANCE DEPTH OF PILE. LATERAL TIES Diameter of Circular ties = 8 mm Spacing of the circular ties : least of the following : i). Diameter of pile = 500 mm ii) 16 1 = 256 mm iii) 300 mm = 300 mm Provide Y8 Dia @ 200mm c/c