Professional Documents
Culture Documents
Code Solution:
0x124 Add/remove Vcore or QPI/VTT voltage (Usually Vcore, once it was QPI/VTT)
0x101 Add more Vcore
0x50 RAM timings/Frequency add DDR3 voltage or add QPI/VTT
0x1E Add more Vcore
0x3B Add more Vcore
0xD1 Add QPI/VTT voltage
0x9C QPI/VTT most likely, but increasing Vcore might help the situation
0x109 Add DDR3 Voltage
0x0A Add QPI/VTT Voltage
You MUST Set Vtt and PLL yourself if you are overclocking, Auto way overvolt
s them in many cases. The rest may or may not need adjusted from stock/auto.
ICH you may need a little bump 1.14 or so depending on your GFX card and dri
ves connected.
MCH Will likely need 1.2-1.3+ depending on memory strap used, timings, and o
verall FSB/Ram speeds
I'm running 3.6 with CPU PLL at 1.57 and CPU Termination at 1.32- I leave CP
U reference on AUTO
MCH Core at 1.20 for 2x2GB sticks
9 x 389mhz = 3.5ghz
vcore 1.4v
ram voltage 2.2v
ram speed : 978mhz
450x8=3600
400x9=3600
1.225vid and runs 3.6 at 1.4v, 400x9
OC at 3.6ghz .
frequency 400x9
vcore 1.4v
vram 2.2v
Estable 3.4:
-------------3.4 Ghz
Multi................................8
FSB.................................425
Vcore...............................1.45 o 1.475
CPU Term..........................1.3
CPU PLL............................1.5
CPU Ref............................0.863
Mch.................................1.34
Mch Ref............................0.863
DRAM Ref...........................1.01
ICH I/0..............................1.57
ICH Core............................1.1
DRAM V..............................2.0
temps idle: 35,35,31,37
temps load: 60,60,58,61
EIST/C1E disabled solo si no se tienen problemas con temperatura
Hey there, I had a q6600 @ 3.6 at one point before i upgraded to my current q965
0. I just tweaked some voltage settings so you may want to look over my bios set
tings and try what you're comfortable with. Use settings at your own risk.
OC Settings:
3.6GHz
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.60GHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400Mhz
PCI Express Frequency (Mhz) .........:Set to 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 266
System Memory Multiplier ..............: 2.50A
Memory Frequency (Mhz) ..............: 1000MHz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 5
tRP'........................................... 5
tRAS.......................................... 15
Advanced Timing Control
tRRD........................................... 4
tWTR.......................................... 4
tWR............................................ 7
tRFC........................................... 53
tRTP........................................... 4
Command Rate (CMD) ....................: 2
Driving Strength Profiles
Driving Strength ............................ 1066MHz
Channel A
Static tRead Value.........................: 10
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................: 10
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
Voltage Type.
... Manual
CPU
CPU Vcore .
.........................: 1.244V
CPU Termination ..... 1.260V
CPU PLL
....1.570V
CPU Referen.
....0.798V
MCH/ICH
MCH Core
..... 1.260V
MCH Reference . . 0.878V
MCH/DRAM Ref. ...... Normal
ICH I/O
..... Normal
ICH Core
...
Normal
DRAM
DRAM Voltage ....1.800V............: 2.0V
DRAM Termination . 0.900V............: Normal
Channel A Reference 0.900V............: Normal
Channel B Reference 0.900V............: Normal
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled]
load
0, 69
1, 62
2, 63
3, 68
idle
0, 43
1, 39
2, 42
3, 42
________________________________________________________________________________
_________________________________________________
________________________________________________________________________________
_______________________________________________
________________________________________________________________________________
__________________________________________________
OC Settings:
3.6GHz
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.60GHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400Mhz
PCI Express Frequency (Mhz) .........: 100Mhz
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
..... 1.200V
CPU Termination ..... 1.38V -> Always lower than VCore, set it to be sure it won't
move
CPU PLL
.... 1.50V -> 1.50V should be enough up to ~500 FSB, set it to be sure it won't
move
CPU Reference.
.... Auto -> Useless to tweak for such a low overclock
MCH/ICH
MCH Core
..... 1.320V -> Maybe more, depends of the board. Don't go past 1.4V for such
a low overclock.
MCH Reference . . Auto -> Useless to tweak for such a low overclock
MCH/DRAM Ref. ...... Auto
ICH I/O
..... 1.50V -> Useless to tweak before ~550 FSB, set it to be sure it won't mov
e
ICH Core
...
1.10V -> Useless to tweak before ~550 FSB, set it to be sure it won't move
DRAM
DRAM Voltage ....1.800V............: 2.1V-2.2V -> Depends of the RAM
DRAM Termination . 0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto
Do not forget two CPUs aren't equal. It's just informative (that's why I added c
omments). Maybe comments will help more than my settings
________________________________________________________________________________
_______________________________________________
________________________________________________________________________________
__________________________________________________
________________________________________________________________________________
_______________________________________________
CPU = Model Intel Q6600
Motherboard = GA-EP45-UD3P v1.1
BIOS Version =f10
Ram = http://www.gskill.com/products.php?index=190 G.skill DDR2 4x2GB 800mhz
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [9X]
Fine CPU Clock Ratio ----------------- : [0.0]
CPU Frequency ---------------------: 3600
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Disabled]
CPU Host Frequency (Mhz) --------------: [400]
PCI Express Frequency (Mhz) ---------- : [100]
C.I.A.2 ------------------------------ : [Disabled]
:
:
:
:
:
:
[Standard]
[Disabled or Not in my bios]
[Auto]
[2.00D]
[Auto] [800]
[Auto] <-- set to MANUAL for overclock
-------------------------------------
:
:
:
:
[Auto]
[Auto]
[Auto]
[Auto]
:
:
:
:
:
:
[Auto]
[Auto]
[Auto]
[Auto]
[4]
[ 2] <--- Auto or 0 or 2 is OK
N/A
Channel A
Static tRead Value --------------------- : [10]
tRD Phase0 Adjustment ------------------ : [Auto]
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
(MY MOBO HAS) DDR WWRITE TRAINING ---- : [Auto]
Also my mobo has Channel A Driving Settings - all on [auto]
Channel B
Static tRead Value --------------------tRD Phase0 Adjustment -----------------tRD Phase1 Adjustment -----------------tRD Phase2 Adjustment -----------------tRD Phase3 Adjustment -----------------Trd2rd(Different Rank) ----------------Twr2wr(Different Rank) ----------------Twr2rd(Different Rank) ----------------Trd2wr(Same/Diff Rank) ----------------Dimm1 Clock Skew Control --------------Dimm2 Clock Skew Control --------------(MY MOBO HAS) DDR WWRITE TRAINING ----
:
:
:
:
:
:
:
:
:
:
:
:
[10]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto] ps
[Auto] ps
[Auto]
1.100V
0.760V
0.900V
1.500V
1.100V
-------------------------------
:
:
:
:
:
1.800V
0.900V
0.900V
0.900V
-------------------------
:
:
:
:
[2.00]
[1]
[1]
[1]
Advanced Settings
Limit CPUID Max. to 3 -----------------No-Execute Memory Protect -------------CPU Enhanced Halt (C1E) ---------------C2/C2E State Support ------------------x C4/C4E State Support ----------------CPU Thermal Monitor 2 (TM2) -----------CPU EIST Function ---------------------Virtualization Technology --------------
:
:
:
:
:
:
:
:
[Disabled]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
[Disabled]
[Disabled]
Integrated Peripherals
Legacy USB Storage Detect -------------- : [Enabled]
(USB Storage Function)
Next up the quad, pretty sure 3.6ghz is achiveable. Set FSB@ 400 Multi x9, manua
lly set RAM timings to run at 800mhz (1:1 ratio again)
with 1.8v. CPU volts: 1.40625v PLL:1.57v MCHcore: 1.3v
________________________________________________________________________________
_________________
________________________________________________________________________________
______________
________________________________________________________________________________
_____________
CPU = Model Intel Q6600
Motherboard = GA-EP45-UD3P v1.1
BIOS Version =f10
Ram = http://www.gskill.com/products.php?index=190 G.skill DDR2 4x2GB 800mhz
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
:
:
:
:
:
:
[Standard]
[Disabled or Not in my bios]
[Auto]
[2.00D]
[Auto] [800]
[Manual]
-------------------------------------
:
:
:
:
[5]
[5]
[5]
[15]
:
:
:
:
:
:
[4]
[4]
[8]
[80]
[4]
[ 2]
N/A
Channel A
Static tRead Value -------------12-------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto]
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
(MY MOBO HAS) DDR WWRITE TRAINING ---- : [Auto]
Also my mobo has Channel A Driving Settings - all on [auto]
Channel B
Static tRead Value --------------12------- : [Auto]
1.100V
0.760V
0.900V
1.500V
1.100V
-------------------------------
:
:
:
:
:
[1.4]
[Auto]
[Auto]
[Auto]
[Auto]
1.800V
0.900V
0.900V
0.900V
-------------------------
:
:
:
:
[2.10]
[1]
[1]
[1]
Advanced Settings
Limit CPUID Max. to 3 -----------------No-Execute Memory Protect -------------CPU Enhanced Halt (C1E) ---------------C2/C2E State Support ------------------x C4/C4E State Support ----------------CPU Thermal Monitor 2 (TM2) -----------CPU EIST Function ---------------------Virtualization Technology --------------
:
:
:
:
:
:
:
:
[Disabled]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
[Disabled]
[Disabled]
Integrated Peripherals
Legacy USB Storage Detect -------------- : [Enabled]
(USB Storage Function)
________________________________________________________________________________
__________________________________________________
________________________________________________________________________________
_____________________________________________________
________________________________________________________________________________
_______________________________________________
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
Trd2rd(Different
Twr2wr(Different
Twr2rd(Different
Trd2wr(Same/Diff
Dimm1 Clock Skew
Dimm2 Clock Skew
Rank)....................: [Auto]
Rank)...................: [Auto]
Rank)...................: [Auto]
Rank)..................: [Auto]
Control...............: [Auto]
Control...............: [Auto]
CPU
PCI
CPU
MCH
CPU
CPU
CPU
CPU
CPU
CPU
Vcore .
.........................: [1.4 o 1.49] << begin with 1.45
Termination ..... 1.200V*.......: [1.24 o 1.32]
PLL
....1.500V*.......: [1.57 o 1.59]
Referen.
....0.755V*.......: [Auto]
Reference2
,,0.800V*.......: Setting not present
MCH/ICH
MCH Core
.....1.100V...........: [1.24 o 1.30]
MCH Reference . .0.800V...........: [Auto]
MCH/DRAM Ref. ......0.900V...........: [Auto]
ICH I/O
.....1.550V............: auto
ICH Core
... 1.100V............: auto
DRAM
DRAM Voltage ....1.800V............: 2.100
DRAM Termination . 0.900V............: [Auto]
Channel A Reference 0.900V............: [Auto]
Channel B Reference 0.900V............: [Auto]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [disable]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: Setting not present
x C4/C4E State Support..................: Setting not present
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
________________________________________________________________________________
___________________________________________________
________________________________________________________________________________
___________________________________________________
________________________________________________________________________________
________________________________________________
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.0 (2.997)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333Mhz
PCI Express Frequency (Mhz) .........:Set to 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< stock
PCI Express Clock Drive.................: <<< stock
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 50-150
ctual voltage is from what you set in the BIOS to what you get in windows, and k
eep that in mind when adjusting. Most P45 boards this difference is about .6
So maybe 1.40 or so for a actual voltage of 1.34 or so for 3.0 All up to your c
hip, you will have to see what you can use.