Professional Documents
Culture Documents
s CONTENTS
SPECIFICATION ....................................................................... 3 PANEL LAYOUT ........................................................................ 4 UNIT LAYOUT ........................................................................... 5 BLOCK DIAGRAM .................................................................... 6 LIST OF IC FUNCTIONS ....................................................... 7/8 WIRING ..................................................................................... 9 DISASSEMBLY PROCEDURE ............................................... 10 LSI PIN DESCRIPTION .......................................................... 18 IC BLOCK DIAGRAM .............................................................. 20 CIRCUIT BOARDS ................................................................. 22 TEST PROGRAM .............................................................. 30/37 OS UPDATE ............................................................................ 43 CHECK POINT TROUBLESHOOTING ................................. 44 SYSTEM FLOW CHART(After turning on the power) ........ 47/48 DISPLAY MESSAGES ....................................................... 49/50 MIDI IMPLEMENTATION CHART ........................................... 51 PARTS LIST OVERALL CIRCUIT DIAGRAM
This document is printed on chlorine free (ECF) paper with soy ink.
SY 001674
20020401-158000
1.499K-0611M I
S08
IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated. WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative. The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
IMPORTANT:
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division. WARNING: IMPORTANT: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus). Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
WARNING:
Lithium batteries are dangerous because they can be exploded by improper handling. Observe the following precautions when handling or replacing lithium batteries.
Leave lithium battery replacement to qualified service personnel. Always replace with batteries of the same type. When installing on the PC board by soldering, solder using the connection terminals provided on the battery cells. Never solder directly to the cells. Perform the soldering as quickly as possible. Never reverse the battery polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not disassemble the batteries. Never heat batteries or throw them into fire.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren.
VARNING
Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti. The following information complies with Dutch Official Gazette 1995. 45; ESSENTIALS OF ORDER ON THE COLLECTION OF BATTERIES. Please refer to the diassembly procedure for the removal of Back-up Battery. Leest u voor het verwijderen van de backup batterij deze beschrijving.
S08
s SPECIFICATIONS
KEY BOARD TONE GENERATOR POLYPHONY MULTI TIMBRE WAVE VOICE 88 keys with Initial Touch(Balanced Hammer Effect Keyboard) AWM2 64 notes 16 521 waveforms Normal Voice Preset 128 User 128 GM2/XG 493 Drum Voice User 2 GM2/XG 29(including 8 Original Voices) User 32 Reverb 17 Chorus 17 Variation 54 SMF Format 0(Direct Play only) SmartMediaTM(3.3 V) *Up to 128 MB can be used. STANDBY/ON, VOLUME, Pitch Bend wheel, Modulation wheel, VOICE, MULTI, SEQ PLAY, UTILITY, CONTROLLER, CARD, EDIT/COMPARE, JOB, STORE(PLAY/STOP), EXIT, Q / W, H / G,PART(ELEMENT/KEY) +/-, MUTE, INC/YES, DEC/NO, PRESET, USER, GM2/XG, CATEGORY SEARCH, Nummeric Keypad, ENTER, Data dial PHONES(Stereo Phone), OUTPUT(Phone): L(MONO)/R, DC IN, FOOT CONTROLLER, FOOT SWITCH, MIDI IN/OUT/THRU, USB, Card slot LCD (Back Light) PA-5C or PA-5D (European model) AC Adaptor, CD-ROM 8W OUTPUT: + 9 2 dBm(10 k), PHONES: + 0 2 dBm(33 ) 1323 (W) x 389 (D) x 159 (H) mm 19.8 kg
MULTI EFFECT
CONNECTORS & TERMINALS DISPLAY ACCESSORIES POWER CONSUMPTION MAXIMUM OUTPUT LEVEL DIMENSIONS WEIGHT
S08
s PANEL LAYOUT
Top Panel
PHONES
OUTPUT L/ MONO R
DC IN
STANDBY ON
FOOT CONTROLLER
FOOT SWITCH
IN
MIDI OUT
THRU
3.3V CARD
USB
DRUM
CATEGORY SEARCH
PIANO
VOLUME
PART/ COMMON VOICE
ORGAN
GUITAR
MUSIC SYNTHESIZER
EDIT
ELEMENT
UTILITY
CONTROLLER
CARD
VOICE
MODE
MULTI SEQ PLAY
MUTE
PRESET
TG
CTRL ASSIGN
DEMO
COMMON
DRUM/PERC
BASS
STRINGS
BRASS
DATA
UTILITY CONTROLLER CARD DEC/NO INC/YES
USER
SE
REED/PIPE
SYN LEAD
SYN PAD
PITCH
MODULATION
EDIT
JOB
STORE
GM2/XG
ENTER
EXIT
COMPARE
PLAY/STOP
OTHER
SYN COMP
q w e r t y u i
o !0 !1 !2 !3 !4 !5 !6
PITCH bend wheel MODULATION wheel [VOLUME] Slider LCD Parameter Type List MODE buttons [PART/ELEMENT/KEY] buttons u-1 [+]/[-] buttons u-2 [MUTE] button DATA buttons i-1 [DEC/NO] button i-2 [INC/YES] button i-3 [H]/[G] buttons i-4 [Q]/[W] buttons [CATEGORY SEACH/DRUM] button [PRESET/(DRUM/PERC)] button [USER/(SE)] button [GM2/XG/(OTHER)] button Numeric keypad [ENTER/KEYBOARD] button [EXIT] button Data Dial
Rear Panel
USB
3.3V
CARD
THRU
MIDI OUT
IN
STANDBY ON
DC IN
OUTPUT L/MONO
PHONES
!7 !8 !9 @0 @1 @2 @3 @4 @5
USB terminal Memory Card slot MIDI IN/OUT/THRU terminals FOOT SWITCH jack FOOT CONTROLLER jack STANDBY/ON switch DC IN terminal OUTPUT L/MONO and R jack PHONES jack
S08
s UNIT LAYOUT
Wheel Assembly
VOL
LCD Assembly
Keyboard Assembly
SW
SW
LCD Assembly
KB
VOL
Control Panel Assembly
SW
LCD Assembly
US DM
Wheel Assembly
CN1-6P
FOOT CONTROLLER
CN3-6P
CN5-5P
S08
s BLOCK DIAGRAM
SW
GH-D_SW H HE-D_SW L
SW
26 RESET 1 SW LED
LC
LED BACKLIGHT
US
SMART MEDIA USB
ROTARY ENCODER
20
CUSTOM LCD
CN2-4P
CN1
KB
CN2
CN2-4P
CN3-6P
DM
RESET 1 10
32
ROM
16Mbit
IC5 48P
(FLASH) PROGRAM
30
RESET 2 CS1
CN1-15P
CN5-36P
CN6-14P
CN4-15P
CN7-36P
MIDI IN
MIDI OUT
CS0 CS1
VOL
CS2 132 LSI IC 125 150 46 93
MASTER VOLUME 3
154
IC12 40P
158 15
LPF
5 VOL
OUTPUT L/MONO
TR2
LPF
AMP
OUTPUT R
PHONES
TR3
+9A
MUTING
+5A
IC29 5 6 +5D IC17 RESET 5 9 8
1
+5D
3 IC9
+9V REG
1
STAND BY/ON
DC IN
CN9
28CA1-8822151
S08
s LIST OF IC FUNCTIONS
Circuit Board IC No IC01 IC02 IC03 IC04 IC05 IC06 IC07 IC08 IC09 IC10 IC11 IC12 IC13 IC14 IC15 IC16 IC17 DM IC18 IC19 IC20 IC21 IC22 IC23 IC24 IC25 IC26 IC27 IC28 IC29 IC30 IC31 IC32 IC33 IC01 IC02 IC03 IC04 IC05 IC06 IC07 IC08 FUNCTION SWX00B SWX00B SRAM 1M (UPPER) SRAM 1M (LOWER) FLASH ROM 16MB MASK ROM 64MB MASK ROM 64MB -REGULATOR REGULATOR -DRAM 4MB OP AMP -REGULATOR OP AMPPROGRAM RESET DAC OP AMP OP AMP Analog Switch REGULATOR Photo Coupler CMOS Gate -CMOS Gate CMOS Gate CMOS Gate CMOS Gate CPU (8MHz) CMOS Gate CMOS Gate CMOS Gate USB CPU CMOS Gate CMOS Gate CMOS Gate CMOS Gate CMOS Gate CMOS Gate CMOS Gate USE CPU (system control) + sound source Sound source SRAM for work/for backup SRAM for work/for backup ROM for system control program ROM1 WAVE ROM L ROM2 WAVE ROM H --DC Regulator + 12V +9V (for analog use) DC Regulator +5V +3.3V (for digital use) --DSP DSP temporary data (for EFFECT) Power amplification (low-impedance drive) --DC Regulator +12V +5V (for digital use) Active filter (LPF) System reset D/A Converter (OUTPUT/PHONES) DC power (analog) DC power 3.3V +1.65V (for digital use) For battery detection DC Regulator 9V +5V (for DAC) MIDI IN MIDI inport (photoelectric transfer) Inverter MIDI OUT/THRU drive --D-FF Rotary encoder input waveform shaping Transceiver Data (two-way) Decoder Address Decoder (chip select) Reset of system for rotary encoder Inverting Schumitt Trigger input waveform shaping system SIO4 4ch Serial I/O interface OR (Buffer) Buffer for HWR2, CRD2 D-FF Logic for SIO4 control signal generation OR Logic for SIO4 control signal generation FLASH USB available microcomputer OR For Smart Media control OR For Smart Media control INVERTER For Smart Media control TRANSCEIVER For Smart Media control BUFFER For Smart Media control D-FF For Smart Media control OR For USB microcomputer control Master (Separate Mode) Slave (Sigle mode) Upper Lower
USB
S08
S08
s WIRING
HED 88 Keyboard
i
VOL
CN3 CN5
SW
LC
CN2 CN1 CN1
KB
CN4
!0 !1
w
WHEEL
e
CN3
r
CN4
t
CN5
y
CN6
q
CN1
CN2
DM
JK9
CN7
CN5
US
AC Adapter
o
Part No. V8626300 V8795500 V8795600 (VK11300) (V875590) VK111600 MF136120 VK109800 VU113800 VU113700 V8029200 (V675990) (V676000) Description Shield Connector Assembly Cable Assembly Cable Assembly KRD-KRD Connector Assembly WHEEL Connector Assembly KRD-KRD Connector Assembly CARD Connector Assembly C&C KRD-KRD Connector Assembly AC Adapter AC Adapter AC Adapter Wire Wire DM-CN1 DM-CN2 DM-CN3 DM-CN4 DM-CN5 DM-CN6 DM-CN7 Keyboard Assembly AC Adapter AC Adapter AC Adapter LC LC Destination VOL-CN3 SW-CN2 KB-CN4 LC-CN1 Wheel Assembly SW-CN1 US-CN5 KB-CN5 DM-JK9 DM-JK9 DM-JK9 REMARKS 6P-550L 4P 6P 15P-500L 5P-140L+X 14P-450L 36P 120mm P=1.25 8P-400L J U E
S08
s DISASSEMBLY PROCEDURE
Caution: Be sure to attach the removed filament tape just as it was before removal. 1. Control Panel Assembly (Time required: about 5 minutes) 1-1 Remove the four (4) screws marked [146], and then remove the cover. KRD-KRD Connector Assembly can then be removed from CN4 on the KB circuit board. (Fig. 1) 1-2 Put the main unit upright with the front rail downward. Remove the six (6) screws marked [140A], the six (6) screws marked [140B], the one (1) screw marked [150]. Then put back the main unit to the original position. (Fig. 1)(Photo. 1) 1-3 Remove the three (3) screws marked [130]. Then remove the side cover R and the two (2) screws marked [100]. Likewise, remove the side cover L and the control panel assembly. (Fig. 1)* * If the control panel assembly is held up with the connector attached on the KB circuit board, the circuit board and wiring may be damaged. Before removing the control panel assembly, be sure to check that the KRD-KRD Connector Assembly is disconnected on the KB circuit board. * When putting the main unit upright, take care not to allow it to fall down.
Side Cover Left Keyboard Assembly Side Cover Right
[100] [130]
[150] [140A]
[146]
KB
[140B] Cover Shield Plate B Assembly Adhesive Tape [100]: [130]: [140A]: [140B]: [146]: [150]: CN4 KRD-KRD Connector Assembly
10
Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Bind Head Screw 4.0X20 MFZN2BL (VB934000) Bind Head Screw 4.0X20 MFZN2BL (VB934000) Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Cup Screw 4.0X18 MFZL2Y (VK348200)
(Photo. 1)
(Fig. 1)
S08
2.
DM Circuit Board & US Circuit Board (Time required: about 10 minutes) 2-1 Remove the control panel assembly. (See Procedure 1.) 2-2 Remove the nine (9) screws marked [300] and the CN4 connector on the KB circuit board. The shield plate B assembly can then be removed. (Fig. 2) Remove the nine (9) screws marked [260] and the four (4) screws marked [280]. Then remove the DM circuit board & US circuit board. (Fig. 3) * For reinstallation, pass the KRD-KRD Connector Assembly through the ferrite core from underneath and pass it over the bush. (Fig. 2-1) Again pass the harness through the ferrite core from underneath and connect it to the CN4 connector. (Fig. 2-2) 3. 3-1 3-2 3-3 KB Circuit Board (Time required: about 10 minutes) Remove the control panel assembly. (See Procedure 1.) Remove the rear panel assembly. (See Procedure 2.) Removed the two (2) screws marked [60]. The KB circuit board can then be removed. (Fig. 2)
[290c]
KB
[300]
(Fig. 2-1)
CN4
(Fig. 2-2)
[290c]: Bind Head Tapping Screw-B 3.0X6 MFZN2BL (EP600230) [300]: Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190)
(Fig. 2)
11
S08
[260]
[210A]
US
[230]
DM
[260]
LITHIUM Battery
[210A] [210]: [230]: [260]: [280]: Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Bind Head Tapping Screw-B 3.0X6 MFZN2BL (EP600230) Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190)
Battery holder
(Fig. 3-1)
(Fig. 3)
4.
Rear Panel Assembly (Time required: about 20 minutes) 4-1 Remove the control panel assembly. (See Procedure 1.) 4-2 Remove the DM circuit board & US circuit board. (See Procedure 2.) 4-3 Remove the three (3) screws marked [230]. The rear panel assembly can then be removed. (Fig. 3, 4)
[210B]
[210B]
[210]:
12
(Fig. 4)
[210B] [210B]
S08
SW Circuit Board (Time required: about 25 minutes) Remove the control panel assembly. (See Procedure 1.) Remove the rear panel assembly. (See Procedure 4.) Remove the nine (9) screws marked [60]. The SW circuit board can then be removed. When installing SW circuit board, take care not to pinch and damage the CN2 cable assembly. (Fig. 5-1) VOL Circuit Board (Time required: about 25 minutes) Remove the control panel assembly. (See Procedure 1.) Remove the rear panel assembly. (See Procedure 4.) Remove the four (4) screws marked [160]. When installing the VOL circuit board, slide the volume knob up and down with the VOL circuit board in contact with the VOL circuit board fixture and check that it moves smoothly. Then secure the circuit board with the screws. (Fig. 5) LCD Circuit Board (Time required: about 25 minutes) Remove the control panel assembly. (See Procedure 1.) Remove the rear panel assembly. (See Procedure 4.) Remove the six (6) screws marked [110]. The LC circuit board can then be removed. (Fig. 5)
SW
Cable Assembly [160] [80] Angle, VOL [162] [80] Wheel Assembly 683 Control Panel SVR Escutcheon [110] LCD Assembly [110] [60]
VOL
(Fig. 5-1)
SW
Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Bind Head Tapping Screw-B 3.0X6 MFZN2BL (EP600230)
(Fig. 5)
13
S08
LC Circuit Board (Time required: about 30 minutes) Remove the control panel assembly. (See Procedure 1.) Remove the rear panel assembly. (See Procedure 4.) Remove the LCD assembly. (See Procedure 7.) Remove the eight (8) screws marked [60]. The LC circuit board can then be removed. (Fig. 6)
[60] Conduction
LC
Rubber Connector
[60]:
(Fig. 6)
Wheel assembly 683 (Time required: about 30 minutes) Remove the control panel assembly. (See Procedure 1.) Remove the rear panel assembly. (See Procedure 4.) Remove the four (4) screws marked [80]. The wheel assembly 683 can then be removed. (Fig. 5) Wheel assembly (Time required: about 32 minutes) Remove the control panel assembly. (See Procedure 1.) Remove the rear panel assembly. (See Procedure 4.) Remove the wheel assembly. (See Procedure 9.) Remove the four (4) screws marked [30]. The wheel assembly can then be removed. (Fig. 7) [30]
MODULATION
(Fig. 7)
14
S08
11. HED Keyboard Assembly (Time required: about 25 minutes) 11-1 Remove the control panel assembly. (See Procedure 1.) 11-2 Remove the nine (9) screws marked [70] and the two (2) screws marked [80]. The HED keyboard assembly can then be removed. (Fig. 8, Fig. 9) * When installing the HED keyboard assembly, balance the low-and high-note white keys in location with the front rail as a guide. The HED keyboard assembly can then be installed.
[70] [70] [70] [80] [70]
[80]
[70]: Pan Head Screw 5.0X25 MFZN2Y PW (VV040700) [80]: Bind Head Tapping Screw-1 4.0X14 MFZN2Y (EP040230)
(Fig. 8)
(Fig. 8-1)
12. Disassembly of HED Keyboard Assembly (Time required: about 50 minutes) * Before removing the circuit board, insert a rod (Rod: TX000670) between the frame and the hammer so as not to distort the seesaw dome (rubber contact). (Fig. 11) 12-1 Remove the control HED keyboard assembly. (See Procedure 11.) 12-2 HE-D_SW Circuit Board L Remove the seven (7) screws marked [260a]. The HE-D_SW circuit L board can then be removed. (Fig. 9) 12-3 GH-D_SW Circuit Board H Remove the ten (10) screws marked [260b]. The HE-D SW circuit H board can then be removed. (Fig. 9) * The white key and black key can be removed without removing the HE-D_SW circuit board L and the GHD SW circuit board H. * Remove the HE-D_SW circuit board L and GH-D SW circuit board H. The seesaw dome (rubber contact) can then be removed.
15
S08
HE-D_SW L GH-D_SW H
[260b] X 10
[260a] X 7
[260a]: Bind Head Tapping Screw-P 3.0X10 MFZN2 (VT413400) [260b]: Bind Head Tapping Screw-P 3.0X10 MFZN2 (VT413400)
(Fig. 9)
12-4 White key Insert a thin plate between the keyboards (in the space pointed at by the triangle mark near the white key fulcrum). Push down the stopper marked [A] and move forward the white key until the white keyboard hook is released. The white key can then be removed by holding it up. (Figs. 10, 11) * While doing the above step, take enough care not to move the white key so far forward to damage the spring. * The black key can be removed by removing the white keys on both sides. 12-5 Hammer white key This key can be unhooked by removing the white key and then by pushing down the spring. (Fig. 12) Turn the GHD keyboard over. Remove the hammer white key by peeling off the stopper L88_W. (Fig. 13) * The hammer black key can be removed by following the same procedure as for the white key.
White Key Thin plate
Spring
Triangle mark
Hook
(Fig. 12)
(Fig. 13)
16
S08
13. HED Keyboard Assembly (Time required: about 30 minutes) 13-1 Hammer white key (black key) Insert the hammer white key (black key) into the frame on the back of the HED keyboard and attach the stopper L88_W. Remove from the main unit. (Fig. 14) 13-2 Spring With the HED keyboard on the top side, push down the two ends of the spring in alignment with the cut in the hammer white key (black key) and attach it to the frame hook. (Fig. 15) * Be careful of the direction of the spring. The spring is shaped like <. Attach it so that its top looks like ^. 13-3 White key (black key) With the white key (black key) caught in the area [B] and key guide, check that the spring is securely located in the spring receptacle inside the keyboard fulcrum. Then slowly push in the top of [C] in the downward direction and install. (Fig. 16) 13-4 HE-D_SW circuit board L Fit the seesaw dome (rubber contact) in the slit on the back of the frame and attach the seven (7) screws marked [260a]. The HE-D_SW circuit board L can then be installed. (Fig. 9) 13-5 GH-D_SW circuit board H Fit the seesaw dome (rubber contact) in the slit on the back of the frame and attach the ten (10) screws marked [260b]. The HE-D_SW circuit board L can then be installed. (Fig. 9)
Stopper L88_W Cut Spring Frame Frame White key [C] Hook
(Fig. 16)
17
S08
SWX00B .................................... Page 18 DAC ........................................... Page 19 SIO4 .......................................... Page 19 KSN2 ......................................... Page 19
DM: IC101 I/O
O O O O O O O O O O O O O O O O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I I I I I I I I O O O O O O O I I I
PIN No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84
I/O
I I I I I O I I I I I I I O O I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
FUNCTION
Initial clear PLL Clock PLL Control Power supply Ground SWX dual mode Power supply Ground crystal oscillator crystal oscillator SWX separate mode TEST pin TEST pin A/D converter Power supply Ground for MIDI or TO-HOST for MIDI Crystal oscillator
PIN No.
85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168
NAME
CMA3 CMA8 CMA2 CRD CMA1 CUB VCC91 GHND92 CS1 CMA0 CLB CMA12 CMA11 CMA10 CMA9 GND100 CWE CMA16 CMA15 CMA14 CMA13 CMD8 CMD7 CMD9 CMD6 CMD10 CMD5 CMD11 CMD4 CMD12 CMD3 CMD13 CMD2 CMD14 VCC119 GND115 CMD1 CMD15 CMD0 CMA21 PDT15 PDT14 PDT13 PDT12 PDT11 PDT10 PDT9 PDT8 VCC133 GND134 PDT7 PDT6 PDT5 PDT4 PDT3 PDT2 PDT1 PDT0 VCA143 GND144 PAD2 PAD1 PAD0 VCC148 GND149 PCS PWR PRD RXD0 RXD1 SCLKI ADIN ADLR DO0 DO1 SYSCLK VCC161 GND162 WCLK QCLK BCLK SYI IRQ0 NMI
FUNCTION
read signal Program address bus high byte effective signal Power supply Ground CS signal Program address bus low byte effective signal Program address bus Ground write signal Program address bus
Power supply Ground Wave memory data bus read signal write signal RAS signal CAS signal REFRESH signal CS signal Memory address bus Memory address bus Power supply Ground
Power supply Ground SWX access address bus Power supply Ground Chip select write enable read enable for Midi or TO-HOST for Midi or Key scan EXT Clock A/D converter A/D converter LR clock DAC DAC 1/2 clock Power supply Ground for DAC LR clock 1/12 clock IIS-DAC clock Synch signal Interrupt request Interrupt request
18
S08
DM: IC018
Channel R voltage reference Channel L voltage reference Channel L output Analog ground Left/right check, Word clock Left/right selection, Channel R series input Series input/Channel L series input Clock
DM: IC030
Data bus Interrupt request Interrupt request Ground Interrupt request Interrupt request Read Write Chip enable Test mode Serial data Ground Power supply
I O I O I
Serial data
25 TX31 O 26 RX32 I 27 TX32 O 28 RX33 I 29 TX33 I/O 30 /IC I 31 VSS31 32 XI I 33 VSS33 34 XO O 35 A0 I 36 A1 I 37 A2 I 38 A3 I 39 A4 I 40 A5 I 41 CPUCLK I 42 VSS42 43 VDD43 44 D0 I/O 45 D1 I/O 46 D2 I/O 47 D3 I/O 48 D4 I/O
Serial data
Initial Clear Ground Crystal quarts input Ground Crystal quarts output
Address bus
Data bus
HE-D_SW L
O I I I I I I O O O O O O O O O
Ground Power supply Serial data Acknowledge/mode select Clock for serial data Initial clear Test mode (L,L: normal mode, others: test) Inhibit of serial clock
19
S08
s IC BLOCK DIAGRAM
NJM4556AM(T1) (XQ138A00) UPC4570G2 (XF291A00) NJM3414AM(T1) (XR294A00) Dual Operational Amplifier
DM: IC013, 016, 019, 020
SN74HCT245NSR (XM909A00) SN74HC245N (IR024550) TC74VHCT245AF (XV242A00) Octal 3-State Bus Transceiver
DM: IC027 SW: IC003 US : IC005
D1R A1 A2 A3 A4 A5 A6 A7 A8 GND 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VCC G B1 B2 B3 B4 B5 B6 B7 B8
1 2 3 4 -V
+V
8 7 6 5
CLEAR 1Q 1D 2D 2Q 3Q 3D 4D 4Q GND
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13 12 11
VCC 8Q 8D 7D 7Q 6Q 6D 5D 5Q CLOCK
+ + -
CL D CK
Q CL CK D
D CK CL Q
CK D CL Q
CL D CK
Q CL CK D
D CK CL Q
CK D CL Q
1A 1Y 2A 2Y 3A 3Y GND
1 2 3 4 5 6 7
14 13 12 11 10 9 8
1 2 3 4 5 6 7 8 B C G2A G2B G1 A
16 Y0 Y1 Y2 Y3 Y4 15 14 13 12 11 10 9
Vcc Y0 Y1 Y2 Y3 Y4 Y5 Y6
1 2 3
Vcc
COUT
Enable
Output
Y7 Y6 Y5
1 2 3 4 5 6 7
14
1A 1B 2Y GND
Vcc 1Y 2B 2A
CLR
13
2 3 4
7 6 5
CLR
CK PR Q Q
12 11 10 9 8
CK PR Q Q
PR L H L H H H
D X X X H L X
OUTPUTS Q Q H L H H L QO L H H L H QO
20
S08
TC74HCT32AF(EL) (XY096A00) SN74HC32N (IR003250) 74VHC32SJX (XY306A00) TC74VHC32F-TEL (XR337A00) TC74VHCT32AFT-EL (XZ372A00) Quad 2 Input OR
DM : IC031 SW: IC005 US : IC002, 003, 008
1A 1B 1Y 2A 2B 2Y GND
1 2 3 14 13 12
1G 1A1 2Y4
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13 12 11
VDD (Vcc) 2G 1Y1 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1
Vcc 4B 4A 4Y 3B 3A 3Y
4 5 6 7
11 10 9 8
21
S08
s CIRCUIT BOARDS
CONTENTS
LC Circuit Board US Circuit Board DM Circuit Board VOL Circuit Board KB Circuit Board SW Circuit Board (XZ147B0) ................................................................... Page 22 (X2190B0) ................................................................... Page 23 (XZ144G0) .................................................................. Page 24 (X2189C0) ................................................................... Page 25 (X2189C0) ................................................................... Page 25 (X2189C0) ................................................................... Page 28
LC Circuit Board
to DM-CN4
Components Side
Pattern Side
LC: 2NA-V626840
22
S08
US Circuit Board
CARD
USB
Pattern Side
US: 2NA-V839530
23
S08
S08
DM Circuit Board
MIDI THRU OUT IN Not Installed Not Installed FOOT SWITCH Overcurrent protection FOOT STANDBY/ON DC IN CONTROLLER not installed OUTPUT R L/MONO PHONES
to US-CN5
to LC-CN1
to SW-CN2
Components Side
KB Circuit Board
Components Side
24
25
S08
S08
DM Circuit Board
Pattern Side
26
DM: 2NA-V862080
27
S08
S08
SW Circuit Board
from DM-CN6 from DM-CN2
CATEGORY SEACH
PIANO
ORGAN
GUITAR
MUTE PRESET
DEMO
COCOMMON
DEC/NO INC/YES
DRUM/PIPE
BASS
STRINGS
BRASS
UTILITY
CONTROLLER
CARD
1 USER
JOB EDIT
STORE GM2/XG
ENTER
EXIT
COMPARE
PLAY/STOP
OTHER
SYN COMP
CHROMTIC PERCUSSION
KEYBOARD
28
SW: 2NA-V839520 2
29
S08
s TEST PROGRAM
(A) LIST OF TESTS
Test No. Test item T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T13 RAM, battery LCD Panel Switch & LED 1 key on Keyboard Pitch Bend Modulation Wheel Foot Controller Foot Switch MIDI IN/OUT/THRU OUTPUT-L Test No. Test item T14 T15 T16 T19 T20 T21 T22 T23 T24 T25 OUTPUT- R Encoder USB (MIDI) Card RAM (SRAM) ROM (Program ROM) Wave ROM Factory Set Exit (Noise Level) Battery
and the test items will be displayed. Pressing the [DEC] button selects the test just before the current one, and the test items will be displayed. Pressing the [ENTER] button executes the current test. Pressing the [EXIT] button during display of the test result exits back to the test item selection. Pressing the [EXIT] button during test item selection ends the test.
01:BATTERY
Check that the voltage of the backup battery is 2.7 V or more. (Test Procedure) The test is executed. (Check Item) The test judgment is checked in LCD. (Judgment Result) OK
TEST:V#.## V$.$$
V#.##: Main Version V$.$$: USB Version After a while the following display will appear. Proceed to the test according to the next PROCEEDING THROUGH THE TEST PROGRAM.
01:BATTERY OK 01:BATTERY NG
NG
(Test End) The test ends after the result is displayed and outputted. (Note) Since a great error occurs before the voltage is settled after power is turned on, wait about 20 seconds after power is on and then start the test.
01:BATTERY
(D) PROCEEDING THROUGH THE TEST PROGRAM
When the test program is started, the following display will appear.
T2. LCD
02:LCD
LCD dots are viewed by the eye and checked. (Test Procedure) The test is executed. (Check Item) Check that all dots are blinking in black and white.
01:BATTERY
Proceed to the test by using the [DEC], [INC], [ENTER], and [EXIT] buttons. Pressing the [INC] button selects the test next to the current one
30
S08
(Judgment Result) None (Test End) Pressing [EXIT] ends the test.
(Check Item) Check that all switches operate correctly. Check that all LEDs turn on or off correctly. (Judgment Result) OK
03:SW LED OK
No display
03:SW LED
NG Check that the panel switch operates correctly. Check that LED turns on or off. (Test Procedure) Turn on or off the panel switches from [MULTI] to [EXIT] according to the LCD display. (Test End) If all switches are judged (have been checked) for correct operation, OK will be displayed and the test will be ended.
T4. 1 KEY ON
04:1KEY ON
Check that the keyboard operates correctly. (Test Procedure)
04:1KEY ON C 3
Perform [KEY ON] on the keyboard displayed in LCD. Performing [KEY ON] on the keyboards other than the one displayed in LCD will be ignored. In a normal state, the sine wave is outputted during [KEY ON] and sound stops at [KEY OFF]. If checked correctly, OK will be displayed. (Check Item) Check that the keyboard operates correctly. (Judgment Result) OK
1 2 3 4 5 6 7 8 9 10 11 12
VOICE MULTI SEQ UTLTY CTRL CARD EDIT JOB STORE + MUTE
13 14 15 16 17 18 19 20 21 22 23 24
-/NO UP +/YES LEFT DOWN RIGHT CTGRY PRE USER GM/XG TEN 7 TEN 8
25 26 27 28 29 30 31 32 33 34 35
TEN 9 TEN 4 TEN 5 TEN 6 TEN 1 TEN 2 TEN 3 TEN 0 TEN ENTER EXIT
NG
04:1KEY ON OK
No display
(Test End) If the keys are checked correctly, OK will be displayed and the test will be ended.
T5. KEYBOARD
05:KBD
Check that the keyboard operates correctly.
Table 1
31
S08
(Test End) End the test after displaying and outputting the judgment.
05:KBD G#3
To check G#3 Perform [KEY ON] on the keyboard displayed in LCD. Performing [KEY ON] on the keyboards other than the one displayed in LCD will be ignored. In a normal state, sine wave is outputted during [KEY ON] and sound stops at [KEY OFF]. If all keys have been checked correctly, OK will be displayed. (Check Item) Check that all keyboards operate correctly. (Judgment Result) OK
07:MW
08:FC
Check that each controller operates correctly. (Test Procedure) Move each controller to the bottom top according to the following LCD display. 00-127
07:MW
yyy xxx
08:FC
yyy xxx
05:KBD OK
NG
No display
(Check Item) Check that the figures change smoothly and that OK judgment is displayed. (Display of Judgment Result) OK
(Test End) If all keys have been checked correctly, OK will be displayed and the test will end.
07:MW OK
08:FC OK
06:PB
Check that the pitch bend operates correctly. (Test Procedure) Move the pitch bend smoothly to the center top bottom according to the following LCD display. 64- 127- 00
NG
NO display
(Test End) End the test after displaying and outputting the judgment.
09:FS
Check that the foot switch input operates correctly. (Test Procedure) Turn on or off the foot switch.
06:PB
yyy xxx
yyy: Next target value xxx: Current data value
(Check Item) Check that the figures change smoothly without a catch and that OK judgment is displayed. (Display of Judgment Result) OK
09:FS
yyy xxx
yyy: Next target value(on/off) xxx: Current data value(on/off)
06:PB OK
(Check Item) Check that the data value changes and that OK judgment is displayed.
NG
06:PB NG
32
S08
09:FS OK
13:OUT L Doing
(Check Item) OUTPUT-L: 880 Hz 3Hz, sine wave, +6.0 2 dBm (load: 10 k) (Distortion factor of 0.1% or less) OUTPUT-R: -80 dBm or less (load: 10 k) PHONES (L): 880 Hz 3 Hz, sine wave, -1.0 2 dBm (load: 33 ) (Distortion factor of 0.1% or less) PHONES (R): -58 dBm or less (load: 33 ) (Display of Judgment Result) OK No display
NG
No display
(Test End) End the test after displaying and outputting the judgment.
10:MIDI
Use the test pattern (AA FF 00 55) to check the operation of MIDI IN/ OUT/ THRU. (Test Procedure) After connecting the MIDI cables, perform the test for IN and OUT. If the test is OK, use the MIDI monitor to check that the test pattern (AA FF 00 55) is outputted from THRU. The following display will appear in the LCD. (Check Item) Check that OK is displayed when IN and OUT are checked and that the test pattern is outputted from THRU. (Display of Judgment Result) OK
NG
No display
(Test End) Pressing [EXIT] ends the sound and the test number is put on standby.
14:OUT R
Check that correct signals are outputted from OUTPUT-R and PHONES (R).
10:MIDI OK
NG
10:MIDI NG
(Test Procedure) Insert the plugs into OUTPUT-L, OUTPUT-R, PHONES (L), and PHONES (R) and observe the output waveform, and output level that are outputted from each of them by using the oscilloscope, and level gauge (with JIS_C filter). Turn the master volume to max. The following display will appear during sound.
13:OUT L
Check that correct signals are outputted from OUTPUT- L and PHONES (L). (Test Procedure) Insert the plugs into OUTPUT-L, OUTPUT-R, PHONES (L), and PHONES (R) and observe the frequency, output waveform, and output level that are outputted from each of them by using the frequency counter, oscilloscope, and level gauge (with JIS_C filter). Turn the master volume to max.
14:OUT R Doing
(Check Item) OUTPUT-L: -80 dBm or less (load: 10 k) OUTPUT-R: 880 Hz 3 Hz, sine wave, +6.0 2 dBm (load: 10 k) (Distortion factor of 0.1% or less) PHONES (L): -58 dBm or less (load: 33 ) PHONES (R): 880 Hz 3 Hz, sine wave, -1.0 2 dBm (load: 33 ) (Distortion factor of 0.1% or less) (Display of Judgment Result) OK No display NG No display
33
S08
(Test End) Pressing [EXIT] ends the sound and the test number is put on standby.
NG (TIME OUT)
16:USBMIDI TM-NG
T15. ENCODER
15:ENCODER
Check that the encoder operates correctly. (Test Procedure) According to the following LCD display, turn the encoder clockwise and then counterclockwise. +0 - > +8 (- 0)- > - 8
T19. CARD
19:CARD
Check that SmartMedia is protected. Check SmartMedia for Format/ Write/ Read/ Verify. Check that SmartMedia is pulled out.
(Check Item) Check that in the right of the screen the figure increases smoothly from +0 to +8 after a clockwise turn and then it decreases smoothly from 0 to 8 after a counterclockwise turn and that the OK judgment appers. (Display of Judgment Result) OK
(Test Procedure) After LCD displays [INS], insert SmartMedia with Protect on 15:ENCODER (sealed). Next, after LCD displays [REPLC], pull out SmartMedia yy xx yy : Clockwise, Counterclockwiseand insert SmartMedia with Protect off (unsealed). Pull out SmartMedia after checking that LCD display changes in the xx : Current value sequence of [DOING] [REMOV]. (Check Item) Check that LCD displays the tests judged to be [OK] (Display of Judgment Result) OK
19:CARD OK
15:ENCODER OK
NG
NG
No display
19:CARD xxxxx
xxxxx : ERROR CODE
(Test End) End the test after displaying and outputting the judgment.
T16. USB(MIDI)
16:USBMIDI
Use the test pattern (f0 55 00 f7) to check USB (MIDI) IN/ OUT for operation. (Test Procedure) Connect the USB terminal and PC and perform the test. (Check Item) Check that an OK message appears in IN or OUT checking.
Error code RD/ WR: Read/ Write error NOCRD: No card (when EXIT is pressed with no card inserted) WRPRT: Write Protect is not identified. ABORT: Abort (interrupted when EXIT is pressed with the card inserted) (Test End) End the test after displaying and outputting the judgment.
T20. RAM
20:RAM R/W
Test is performed for Write/ Read/ Verify for SRAM.
16:USBMIDI OK 16:USBMIDI NG
NG
34
S08
(Check Item) The test result is checked in LCD. (Display of Judgment Result) OK
(Check Item) The test result is checked in LCD. (Display of Judgment Result) OK
20:RAM R/W OK
22:WaveROM OK
NG
20:RAM R/W NG
NG
22:WaveROM NG
(Test End) End the test after displaying and outputting the judgment. (Note) All data on RAM is stored. Data will be evacuated immediately before verifying check and be stored immediately after it in repeated sequence.
(Test End) End the test after displaying and outputting the judgment.
23:Factory
Data is set to the factory set data.
T21. ROM
21:ROM
Program ROM is checked for ID. Check RY/BY_ for operation (write into a specific address). (Test Procedure) The test is executed. (Check Item) The test result is checked in LCD. (Display of Judgment Result) OK (Test Procedure) Pressing [ENTER] restores the factory setting and the screen exits. (Check Item) None (Display of Judgment Result)
23:Factory OK
(Note) For shipping, each controller on the main unit is set as follows. Volume Slider Minimum Pitch Bend Wheel Medium Modulation Wheel Minimum STANDBY/ON STANDBY
21:ROM OK
NG
21:ROM NG
(Test End) End the test after displaying and outputting the judgment.
T24. EXIT
24:EXIT
22:WaveROM
Get out of the test mode.
Check 2 WAVE ROMs for the following. All addresses are subjected to the same judgment process as is made on the correctness of the data read for the address for which only one address line applies to 1. In addition, the same check is done for the address 0. (Test Procedure) The test is executed.
(Test Procedure) EXIT is executed by pressing [ENTER]. (Check Item) None (Display of Judgment Result) None
35
S08
(Test End) EXIT is executed by pressing [ENTER]. (Note) Getting out of the test mode is followed by the same sequence as when power is turned on. Also check that the noise level meets the following conditions when none of the note-on steps are made in normal mode after a test subsequent to the factory set. Measure using the level gauge (with JIF-C filter). OUTPUT-L- - - - - - - - - - > -87 dBm or less (load: 10 k) OUTPUT-R- - - - - - - - - - > -87 dBm or less (load: 10 k) PHONES-L- - - - - - - - - - > -94 dBm or less (load: 33 ) PHONES-R- - - - - - - - - - > -94 dBm or less (load: 33 ) Power consumption: Measured at DC IN terminal 230 mA 10 %
T25. BATTERY
Perform the test 30 seconds before power is on or after power is off. Check the voltage between the positive terminal of C154 and DGND. (Test Procedure) Perform measurement of the voltage between the positive terminal of C154 and DGND using an instrument with an impedance of 1M ohms or more. (Check Item) Check that the voltage is 2.6 V or more and 3.2 V or less.
36
S08
37
S08
38
S08
39
S08
40
S08
41
S08
42
S08
s OS UPDATE
CAUTIONS Make sure you store your user data before executing the update. * Tools required for update: 8MB or larger smart media Smart media floppy disk adaptor
* Download the S08 updated program from the download page on the YSISS Homepage to the smart media. (YSISS URL >> http://plaza.yamaha.co.jp/ysiss/exindex.nsf) (Insert a smart media containing only the update program (0683EXT1.pgm) Into the card slot on the main unit.) 1. Insert the smart media containing the upgrade program into the slot on the Rear panel. The correct direction of media is printed on the panel. 2. Turn the power on with "VOICE" button "EDIT" button and "STORE" button pressed and held. (The upgrade screen is displayed on LCD.)
3. Press "ENTER" button after the version check. The program is updated automatically and the process is displayed on LCD. (It takes about 3 minutes.) Press "ENTER"
4. If the program successfully updated the "Complete!" message shown in appears. Turn the power off.
5. Remove the smart media from the slot. 6. Turn the power on with "VOICE" button "EDIT" button and "STORE" button pressed and held again. Make sure of Version. It is completion above.
* NOTES <In case the update fails> After updating, if the system on the S08 does not operate when the power is switched on, update again. If the software will not update again, repair the following: Symptom: System on the S08 does not operate when the power is switched on. <REPAIR PROCEDURE> q Replace the FLASH ROM (IC5: X2380D00) on the DM circuit board. w After changing, load the new version software of the program again. e Check the "new version" and system operation.
43
S08
s CHECK POINTTROUBLESHOOTING
1. Backlight alone turns on, or screen freezes. (Or test mode is inaccessible.)
1-1) Reset circuit Check each of the circuits below. Check Check for Reset Reset IC17-7pin/CPU IC1-1pin (TP7) for wave forms. [Action] After checking the above, replace any defective IC.
Steady state
IC17-7 pin
1-2) Clock circuit Check CLOCK 8.4672MHz/ CPU IC1-9, 10pin for waveforms. [Action] Check the quartz oscillator. If it is not oscillating, replace it.
Steady state
Steady state
IC1-9 pin
IC1-10 pin
1-3) CS circuit Check the following terminals for waveforms. CS0 for Program ROM: TP10/CPU IC1-46pin/FROM IC5-26pin CS1 for SRAM: CPU IC1-93pin/SRAM IC3, IC4- 22pin CS2/CPU IC1-132pin for peripheral devices CS2/CPU IC1-131pin for peripheral devices CS/Wave ROM IC6, IC7-12pin for Wave ROM [Action] After checking the above, resolder or replace IC.
Steady state
Steady state
44
S08
Steady state
Steady state
1-4) CPU peripheral circuit (SWX00/Program ROM/SRAM) Check the following terminals for waveforms. CPU (SWX00) IC1/ data/ address bus Program ROM IC5/ data/ address SRAM IC3, IC4/ data/ address bus [Action] After checking the above, re-solder or replace IC.
Steady state
Steady state
1-5) LCD peripheral circuit LCD Controller IC1 (LC circuit board) LCD unit [Action] After checking the above, resolder or replace IC. In case of the failure of LCD, replace it.
2. It takes time for an opening message to appear. (About 7 seconds) Something may be wrong with communication with USB microcomputer, so check the following circuit.
2-1) USB microcomputer circuit USB microcomputer reset IC1-10pin [Action] After checking the above, replace any defective IC.
Steady state
IC1-10 pin
45
S08
2-2) USB microcomputer clock CLOCK 16MHz/USB microcomputer IC1-14 pin, 10pin for waveforms. [Action] Check the quartz oscillator. If it is not oscillating, replace the quartz oscillator (CLOCK 16MHz). Steady state
IC1-14 pin
2-3) CPU peripheral circuit (SWX00/ Program ROM/SRAM) CPU (SWX00) IC1 USB microcomputer/ data address [Action] After checking the above, re-solder or replace IC.
3. Screen freezes when it is opened. Address data between CPU/ P.ROM/ SRAM may be judged to be OK. Check the following circuit for [I/F IC each device].
3-1) USB connection connector, interface circuit [Action] P. ON after USB cable is pulled out. Replace USB connector. Re-connect YSB cable.
46
S08
Power ON
resetting for the following devices Hard through reset circuit. SWX00 (master, slave) Key scan microcomputer SIO4 (IC for serial communication) USB microcomputer USB microcomputer
Main CPU Initialization of sound (SWX00 master) source section for SWX00
Initialization
yes
yes
state gets available on Steady any one of the following screens Voice Play Top screen Multi Play Top screen Seq Play Top screen
47
S08
48
S08
s DISPLAY MESSAGES
Message Meanings
Relevant Sequencer Operations or Standard MIDI File Playback !CantOpen Cant nd the specied type of le. !CantPlay Cant play the sequencer in these operating conditions. !IllglFile The specied SMF for playing is unusable by the S08. !No SMF The SMF was not found on the card. !Not Frmt0 The SMF format (1) is not supported by the S08. !Not SMF Cant play the specied type of le. !IllglSMF* An error in reading the SMF (other than those described above) occurred. Relevant Card Operations !Bad File Data in the le is corrupted and cannot be used. !CantOpen An error occurred while reading from Memory card. !Card Full No more available memory on the Memory Card. !FileHdErr File format is not recognized. File None Cant nd the specied type of le. !Format An error occurred while formatting the card. Format the card again. !Mount Err An error occurred while mounting the Memory Card. !No Card Memory Card has not been inserted, or an incompatible card (5V type) has been inserted. !No Name Specify the le name. !OVER 256 No more les can be created. OverWrite There is a le already stored with the same name. Replace it with a newer one with that name? !Protected Memory Card is write protected. !Read Only File is a read-only type, and cannot be deleted, renamed or overwritten. !SameName File with the same name already exists. !TooMany The maximum number of displaying les (100) has been exceeded. !Write Err An error occurred while writing to Memory card. Others !BatteryLo The memory-backup battery is low; memory cannot be backed up. Store the necessary data to a Memory Card. !Buff Full Failed to process the MIDI data because too much data was received at once. Bulk Rx... MIDI Bulk data being received. Bulk Tx... MIDI Bulk data being transmitted. !Checksum Error occurred when receiving bulk data. Completed! Operation has been completed. !DeviceNum Bulk data cannot be transmitted/received because the device number does not match or is set to off. Executing Operation is being executed. !MIDI Data Error occurred when receiving MIDI data. Sure? Final conrmation.
49
S08
50
S08
51
S08
52
PARTS LIST
s CONTENTS
OVERALL ASSEMBLY ............................................................... 2 CONTROL PANEL ASSEMBLY ................................................. 4 SW CIRCUIT BORAD ASSEMBLY ............................................ 6 HED KEYBOARD ASSEMBLY ................................................... 7 LCD ASSEMBLY ........................................................................ 8 WHEEL ASSEMBLY 683 ........................................................... 9 WHEEL ASSEMBLY .................................................................. 9 ELECTRICAL PARTS .............................................................. 10
Notes: DESTINATION ABBREVIATIONS A: Australian model B: British model C: Canadian model E: European model H: North European model I: Indonesian model J: Japanese model U: U.S.A. model V: General export model (110V) W: General export model (220V) X: General export model Y: Export model
The numbers in QTY show quantities for each unit. The parts with -- in Parts No. are not available as spare parts. The mark } in the remarks column indicates that these parts are interchangeable. The second letter of the shaded ( ) part number is I, not one.
s WARNING
Components having special characteristics are marked specification equal to those originally installed. and must be replaced with parts having
S08
s OVERALL ASSEMBLY
*Please remove, when you use it.
130
120
144
10f
30 20 150
40
S08
REF NO. PART NO. DESCRIPTION V8594200 V8594300 V8594400 ET200070 ET200030 ET200080 V8040100 V8814100 VR707800 VB403600 -V8594600 EP030340 EG330320 V7411600 VK109800 VA126100 VV040700 EP040230 V8594800 EP600190 V8597100 V8597200 EP600190 VB934000 VA126100 V8974200 EP600190 VK348200 OVERALL ASSEMBLY Overall Assembly Bottom Board Assembly Bottom Board Nut Nut Nut Cushion Rubber Black Cushion Rubber Black Foot Bind Head Screw Tape Front Rail Assembly Bind Head Tapping Screw-1 Bind Head Tapping Screw-1 Keyboard Assembly Connector Assembly Adhesive Tape Pan Head Screw Bind Head Tapping Screw-1 Control Panel Assembly Bind Head Tapping Screw-B Side Cover Right Side Cover Left Bind Head Tapping Screw-B Bind Head Screw Adhesive Tape Cover Bind Head Tapping Screw-B Cup Screw
REMARKS S08
QTY RANK
10 10a 10a1 10a2 10a3 10b 10c 10d 10e 10f 20 30 40 50 60 62 70 80 90 100 110 120 130 140 142 144 146 150
K3019 4.0X20 MFZN2BL 25.4MMX16.4 3.5X12 MFZN2BL 3.5X12 MFZN2BL A88 K6 8P-400 12X50 5.0X25 MFZN2Y PW 4.0X14 MFZN2Y 3.0X8 MFZN2BL
5 5 (2205340) 5 2
02 01
01 01 51 03 01 01 01
9 2 4
6 01 12 01 03 4 01
--
ACCESSORIES Tools for S08 CD-ROM Accessory of the CD-ROM is not a Service Part. PA-5C J PA-5C U/C PA-5D E J U E
(X2475B0)
: New parts
S08
180a
10 380
190 180b 180c 70 80 180 240 310 150 162 370 250 260 390 230 220 290a 230 270a 300 290d 280 270b 262 252 260 270c 140 130 160 270d 50 270 160 110 162 120 20 30 40 90
360 170
190 60
290f 290e 290b 290c 290 300 200d 210 200c 320 330 210 340 350 200b 210 200c 200d 200b 200 200c 200b 200c 210 200c 200a 210
S08
REF NO. PART NO. DESCRIPTION V8594800 V8594900 V2772900 VU354700 VH810100 V8597600 EP600190 V8600800 EP600190 V8598100 CB829850 EP600190 V8626100 V8626300 V8598300 CB829850 EP600190 EP600230 V8598400 V8598600 V8598800 EP600230 V8598500 V8598700 V8598900 EP600230 EP600230 V8599000 V8599100 V8599300 EP600190 V3079400 EP600190 -EP600230 V8620800 CB829850 V8795600 EP600190 CB069250 -V8395300 V3882500 EP600190 MF136120 EP600190 --V8893800 EP600230 VC362700 CB069250 V3079400 EP600190 V4063000 VG016600 EP600190 V3883200 EP630210 V6923600 CB825380 VB774000 VN103500 CONTROL PANEL ASSEMBLY Control Panel Assembly Control Panel SRV Escutcheon Tape Dust-Proof Cloth Circuit Board Assembly Bind Head Tapping Screw-B Wheel Assembly Bind Head Tapping Screw-B LCD Assembly Cord Binder Bind Head Tapping Screw-B Circuit Board Connector Assembly Angle, VOL Cord Binder Bind Head Tapping Screw-B Bind Head Tapping Screw-B Angle R Assembly Side Angel End Block Bind Head Tapping Screw-B Angle L Assembly Side Angle End Block Bind Head Tapping Screw-B Bind Head Tapping Screw-B Rear Panel Assembly Rear Panel Angle Bracket, Panel Bind Head Tapping Screw-B Bushing Bind Head Tapping Screw-B Shield Plate A, DM Bind Head Tapping Screw-B Circuit Board Cord Binder Cable Assembly Bind Head Tapping Screw-B Cord Holder Circuit Board Assembly Circuit Board SM Escutcheon Bind Head Tapping Screw-B Connector Assembly Bind Head Tapping Screw-B Shield Plate B Assembly Shield Plate Circuit Board Bind Head Tapping Screw-B Ferrite Core Cord Holder Bushing Bind Head Tapping Screw-B Felt Cord Column Bind Head Tapping Screw-B Angle, AS Bind Head Tapping Screw-S Encoder Knob Push Button Knob, VR Lithium Battery
REMARKS S08
QTY RANK
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 162 170 170a 170b 170c 180 180a 180b 180c 190 200 200a 200b 200c 200d 210 220 230 240 250 252 260 262 270 270a 270b 270c 270d 280 290 290a 290b 290c 290d 290e 290f 300 310 320 330 340 350 360 370 380 390
EX5 5X20 SW 3.0X8 MFZN2BL 3.0X8 MFZN2BL S-34Z 3.0X8 MFZN2BL VOL KR-KR 6P 550L 1 S-34B 3.0X8 MFZN2BL 3.0X6 MFZN2BL Right Right 3.0X6 MFZN2BL LEFT LEFT 3.0X6 MFZN2BL 3.0X6 MFZN2BL (X2189B0)
04 2 01 9 4 01 01 03 01
6 (X2189B0)
4 3
03 01 01
01
2 6
01 01
1.6 C 3.0X8 MFZN2BL SB-1909 3.0X8 MFZN2BL 0.8 C 3.0X6 MFZN2BL DM S-34Z 6P 3.0X8 MFZN2BL BK-1 US US K-CB 3.0X8 MFZN2BL 36P 120mm P=1.25 3.0X8 MFZN2BL B KB 3.0X6 MFZN2BL FR25/15/12-1400L BK-1 SB-1909 3.0X8 MFZN2BL LM WT11 3.0X8 MFZN2BL K-AA 3.0X6 MFZN2BL K-CB
CR2032
: New parts
S08
130
90
10
40
20
110
70
120
100
30
70
50
80
60
30
REF NO. PART NO. DESCRIPTION V8597600 V8626000 V4162600 V4162700 CIRCUIT BOARD ASSEMBLY Circuit Board Assembly Circuit Board Push Button Push Button SW SW M1B M2B M3B M1DG M2DG M3DG
REMARKS S08 (X2189B0) DEC/NO, INC/YES JOB, STORE, PLAY/STOP, ENTER, KEYBOARD, EXIT +, COMMON, -, MUTE H SYN COMP, CHOROMATIC PECUSSIon UTLITY, CONTROLLER, CARD, Q, G, W, 7, 8, 9, 4, 5, 6, 1, REED/PIPE, 2, SYN LEAD, 3, SYN PAD PRESET, DRUM/PERC, USER, SE, GMX2/XG, OTHER VOICE, MULTI, SEQ PLAY, DEMO EDIT, COMPARE CATEGORY SEACH
QTY RANK
10 20 30 40 50 60 70
2 2
01 01
01 01 5
V 6 7 7 6 8 0 0 Push Button V7039600 V6776500 V8600100 V8795500 VK111600 Push Button Push Button Push Button Cable Assembly Connector Assembly
01 03 01
: New parts
S08
20
30
40
50
110
10
60
70
230
224
210 260 310 300 240 190 150 260 220 222
REF NO. PART NO. DESCRIPTION V7411600 VU422100 VU101000 VU101100 VU101200 VU101300 VU101400 VU101500 VU101600 VU101700 VU101800 VU102100 VY828800 VY829200 VU342100 V7640100 VY846700 VY846800 VY846900 V7411800 VZ705300 VT413400 V2798500 V2211300 -VU341800 VU341900 -KEYBOARD ASSEMBLY Keyboard Assembly MK Frame White Key White White Key White White Key White White Key White White Key White White Key White White Key White White Key White White Key White Black Key White Hammer, White Key4 Hammer, Black Key4 Stopper Stopper Seesaw Dome Seesaw Dome Seesaw Dome Circuit Board Circuit Board Bind Head Tapping Screw-P Spring R White/Black Rubber 2 Grease Connector Assembly, Block Connector Assembly, Note Dry Grease A88 K6
REMARKS S08
QTY RANK 51 7 7 7 7 7 7 8 05 05 05 05 05 05 05 05 05 05 05 05 09 07 08 08 08 10 13 01
10 20 30 40 50 60 70 80 90 100 110 150 190 200 210 220 222 224 230 240 260 270 280 290 300 310 320
36 52 36 1229X12X14.8T 1239.5X28X10.1T GH 2M OCT GH 2M OCT GH 2M OCT HE-D_SW L GH-D_SW H 3.0X10 MFZN2 GH GH,GHD,HE G-1006Y 9P 12P FL-78A
(XT240A0) (XT241A0)
: New parts
S08
s LCD ASSEMBLY
10
20
40
40
30
70 80
50
110 60
120
REF NO. PART NO. DESCRIPTION V8598100 V8598200 V8624300 V5264900 V3755900 V6760100 EP600280 ----LCD ASSEMBLY LCD Assembly LCD Escutcheon LCD Back Light Assembly Rubber Connector Circuit Board Bind Head Tapping Screw-P Wire Wire Adhesive Tape Connector Assembly REMARKS S08 LCD AS TSB0794-DGTDCN-C1 A PT SS-105L LC 3.0X8 MFZN2Y A B 12X60 15P-500 QTY RANK
10 20 30 40 50 60 70 80 110 120
07 01 08 01
: New parts
S08
10
REF NO. PART NO. DESCRIPTION V8600800 V8598000 V8597900 EP600230 WHEEL ASSEMBLY Wheel Assembly Wheel Escutcheon Wheel Assembly Bind Head Tapping Screw-B
REMARKS S08
QTY RANK
10 20 30
3.0X6 MFZN2BL
01
s WHEEL ASSEMBLY
PITCH BEND
W20 W30 W50 W80 W10 W60 W90
BLUE RED ORANGE BLACK
MODULATION
W20
W40
W80
W90
W10 W70
RED GREEN BLACK
REF NO. PART NO. DESCRIPTION W10 W20 W30 W40 W50 W60 W70 W80 W90 V8597900 VF536800 V4579900 VC792800 CB819020 EW600110 VQ764300 VN245400 -CB069250 WHEEL ASSEMBLY Wheel Assembly Frame Wheel Spring Wheel Tube Stop Ring Rotary Variable Resistor Rotary Variable Resistor Connector Assembly Cord Holder
REMARKS S08
QTY RANK
EX
2 2 2
02 04 01 04 01 03 03 01
: New parts
S08
s ELECTRICAL PARTS
REF NO. PART NO. DESCRIPTION V8620800 VZ705300 V7411800 V6760100 V8626000 V8626100 V8893800 V8395300 V8620800 -EG330360 VN103600 US064100 US063220 US063220 US064100 VH340500 UI548100 VH340500 UF138220 UF038100 UF037470 US063100 US063100 UF037470 UF037220 UF138220 UF037220 UF138220 US062470 US062470 UF037100 US062100 US062100 UF056330 US061270 US061270 UF037100 UF037100 US064100 US064100 UF037100 UF037100 US061470 US061470 US064100 US062100 US062100 US062820 US064100 US064100 US062820 US064100 US064100 UF037100 US064100 US064100 UF037100 US064100 US064100 US064100 US064100 UF037100 US064100 US064100 UF037100 UF037100 US062680 UB052100 US062680 UB052100 UF038100 US062100 ELECTRICAL PARTS Circuit Board Circuit Board Circuit Board Circuit Board Circuit Board Circuit Board Circuit Board Circuit Board Circuit Board Holder, Jack Bind Head Screw Battery Holder Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap.-RS Electrolytic Cap. Electrolytic Cap.-RS Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Electrolytic Cap. (chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Electrolytic Cap. (chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-CH(chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Ceramic Capacitor-SL(chip) Monolithic Ceramic Cap. Ceramic Capacitor-SL(chip) Monolithic Ceramic Cap. Electrolytic Cap. (chip) Ceramic Capacitor-SL(chip) DM GH-D_SW H HE-D_SW L LC SW VOL KB US DM 3.0X6 MFZN2BL CR2032 0.0100 50V K 2200P 50V K 2200P 50V K 0.0100 50V K 470.00 25.0V 100.00 25.0V 470.00 25.0V 220 16V UUR1C2 100 16V 47 16V 1000P 50V K 1000P 50V K 47 16V 22 16V 220 16V UUR1C2 22 16V 220 16V UUR1C2 470P 50V J 470P 50V J 10 16V 100P 50V J 100P 50V J 3.3 35V 27P 50V J 27P 50V J 10 16V 10 16V 0.0100 50V K 0.0100 50V K 10 16V 10 16V 47P 50V J 47P 50V J 0.0100 50V K 100P 50V J 100P 50V J 820P 50V K 0.0100 50V K 0.0100 50V K 820P 50V K 0.0100 50V K 0.0100 50V K 10 16V 0.0100 50V K 0.0100 50V K 10 16V 0.0100 50V K 0.0100 50V K 0.0100 50V K 0.0100 50V K 10 16V 0.0100 50V K 0.0100 50V K 10 16V 10 16V 680P 50V J SL 100P 50V J 680P 50V J SL 100P 50V J 100 16V 100P 50V J REMARKS S08 (XZ144G0) (XT241A0) (XT240A0) (XZ147B0) (X2189B0) (X2189B0) (X2189B0) (X2190B0) (XZ144G0) (V776760) 01 03 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 RANK: Japan only 13 10 08 QTY RANK
20 40 BT001 C0001 C0002 C0003 C0004 C0005 C0006 C0007 C0008 C0010 C0011 C0012 C0013 C0014 C0015 C0016 C0017 C0018 C0019 C0020 C0021 C0022 C0023 C0024 C0025 C0026 C0027 C0028 C0029 -0038 C0039 -0042 C0046 C0047 C0053 C0060 C0061 C0062 C0063 -0065 C0066 C0067 -0070 C0071 C0072 -0080 C0081 C0082 C0084 C0088 -0090 C0091 C0092 C0093 C0094 C0095 C0096 C0097 C0098 C0099 C0100 C0101
: New parts
10
S08
REF NO. PART NO. DESCRIPTION C0102 C0103 C0104 C0105 C0106 C0107 -0109 C0110 -0117 C0118 C0119 C0120 C0121 C0122 C0123 C0124 C0125 C0126 C0127 C0128 C0129 C0130 C0131 C0134 C0135 -0138 C0139 C0140 -0143 C0144 C0145 C0146 C0147 C0148 C0149 -0152 C0153 C0154 C0155 C0156 C0157 -0160 C0161 -0163 C0164 C0165 C0166 CN001 CN002 CN003 CN004 CN005 CN006 CN007 D0001 D0002 D0009 D0010 D0011 D0012 D0013 D0014 D0015 D0021 -0026 EM001 EM002 EM003 -0011 IC001 IC002 IC003 IC004 IC005 IC006 US064100 US064100 US062680 US062100 US062680 US064100 US064100 US061470 US061470 US063560 US063560 US064100 UF037100 UF037100 UF037470 UF037470 UF038100 UF037100 US064100 UF037220 US064100 US064100 UF037470 US135100 US064100 US064100 UF038100 US135100 US135100 UF037100 UF037100 US135100 US064100 UF037100 US064100 US064100 UF037100 VD989700 US061470 US061470 US063220 US063220 VR813200 VR813200 US135100 US135100 US064100 VB390200 VK024800 VF728300 VF283300 VB390100 VE352600 VQ048500 VZ016600 VT332900 VS201100 VZ016600 VS201100 VS201100 VT332900 VT332900 VV925900 VT332900 VT332900 VR193800 VR193800 V6196600 V6196600 XU947C00 XU947C00 XT138A00 XT138A00 X2380D00 XZ193100 Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-F (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Tantalum Cap. Ceramic Capacitor-CH(chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-B (chip) Connector Base Post Wire Trap Wire Trap Connector Base Post Connector Base Post Connector Base Post Connector Assembly Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode LC Filter LC Filter EMI Filter (chip) EMI Filter (chip) IC IC IC IC IC IC 0.0100 50V K 0.0100 50V K 680P 50V J 100P 50V J 680P 50V J 0.0100 50V K 0.0100 50V K 47P 50V J 47P 50V J 5600P 50V K 5600P 50V K 0.0100 50V K 10 16V 10 16V 47 16V 47 16V 100 16V 10 16V 0.0100 50V K 22 16V 0.0100 50V K 0.0100 50V K 47 16V 0.1000 16V Z 0.0100 50V K 0.0100 50V K 100 16V 0.1000 16V Z 0.1000 16V Z 10 16V 10 16V 0.1000 16V Z 0.0100 50V K 10 16V 0.0100 50V K 0.0100 50V K 10 16V 4.70 16V M 47P 50V J 47P 50V J 2200P 50V K 2200P 50V K 1.0 16V K 1.0 16V K 0.1000 16V Z 0.1000 16V Z 0.0100 50V K PH- 6P TE 52147 4P TE 52147 6P TE PH-15P TE PH- 5P TE PH-14P TE FFC 52045 36P TE D3FP3 1SS355 TE-17 D1F60 D3FP3 D1F60 D1F60 1SS355 TE-17 1SS355 TE-17 RLS-73 TE-11 1SS355 TE-17 1SS355 TE-17 STF-104ZB-TBM STF-104ZB-TBM NFM4516P13C204FT1 NFM4516P13C204FT1 HG73C205AFD HG73C205AFD UPD431000AGW-70LL UPD431000AGW-70LL 683V104 WAVE
REMARKS
SWX00B SWX00B SRAM UPPER SRAM LOWER FLASH ROM 16M ROM1 64M
: New parts
11
S08
REF NO. PART NO. DESCRIPTION IC007 IC009 IC010 IC012 IC013 IC015 IC016 IC017 IC018 IC019 IC020 IC021 IC022 IC023 IC024 IC026 IC027 IC028 IC029 IC030 IC031 IC032 IC033 JK001 JK002 -005 JK007 JK008 JK009 K0001 L0001 -0003 L0004 -0007 L0008 L0009 L0025 L0026 L0027 L0029 L0030 -0033 L0041 -0051 RA002 -008 RA009 RA010 RA013 -018 RA019 RA020 RA021 RA022 RA024 RA025 -029 RA030 R0001 R0002 R0003 R0005 -0010 R0012 R0013 R0014 R0015 R0016 R0017 R0018 R0020 R0021 R0022 R0023 R0029 XZ194100 XT441A00 XS516A00 XV077B00 XQ138A00 XT442A00 XF291A00 XI686A00 XP867A00 XF291A00 XR294A00 XR682A00 XJ598A00 VN686000 XI297A00 XY153A00 XM909A00 XW793A00 XW104A00 XV833A00 XY096A00 XV892A00 XY364A00 VE382300 VS115400 VS115400 VT033600 VJ885500 LB302260 BA808520 VL139800 VL139800 VR579900 VR579900 VL139800 VL139800 VR579900 VR579900 VR579900 VZ017900 VR579900 VR579900 VR579900 VR579900 RE044000 RE044000 RE045100 RE045100 RE044000 RE044000 RE047220 RE046100 RE047220 RE047220 RE045100 RE047220 RE047220 RE044000 RD256470 RD356100 RD356100 RD255220 RD255220 RD356100 RD154470 RD355100 RD154470 RD356100 RD356100 RD357100 RD355560 RD356100 RD357100 RD357100 RD357100 IC IC IC IC IC IC IC IC IC IC IC IC IC Photo Coupler IC IC IC IC IC IC IC IC IC Phone Jack Phone Jack Phone Jack DIN Connector DIN Connector Connector Heat Sink Chip Solid Inductance Chip Solid Inductance Chip Inductance Chip Inductance Chip Solid Inductance Chip Solid Inductance Chip Inductance Chip Inductance Chip Inductance Coil Chip Inductance Chip Inductance Chip Inductance Chip Inductance Resistor Array (chip) Resistor Array (chip) Resistor Array Resistor Array Resistor Array (chip) Resistor Array (chip) Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) WAVE UPC2909T-E1 UPC2933T-E1 MSM514260E-60JS NJM4556AM(T1) SI-8050S UPC4570G2 M62021FP UPD63200GS-E1 UPC4570G2 NJM3414AM(T1) TC7S66F NJM78L05UA PC410T TC74HCT04AF-T1 MM74HC74ASJX SN74HCT245NSR SN74HC138NSR MM74HC14SJX MBCG46183-129PFV-G TC74HCT32AF(EL) TC74VHC74FT TC7WH32FU(TE12L)OR YKB21-5010 LGR4609-7000 LGR4609-7000 3P YKF51-5067 3P YKF51-5054 HEC0470-01-630 T220M 25L BLM31A700SPT 70ohm BLM31A700SPT 70ohm BK2125HS601-T BK2125HS601-T BLM31A700SPT 70ohm BLM31A700SPT 70ohm BK2125HS601-T BK2125HS601-T BK2125HS601-T HP-022J 180uH BK2125HS601-T BK2125HS601-T BK2125HS601-T BK2125HS601-T 0X4 0X4 100X4 100X4 0X4 0X4 22KX4 1KX4 22KX4 22KX4 100X4 22KX4 22KX4 0X4 4.7K 0.1 J 1.0K 63M J 1.0K 63M J 220.0 0.1 J 220.0 0.1 J 1.0K 63M J 47.0 1/4 J 100 63M J 47.0 1/4 J 1.0K 63M J 1.0K 63M J 10K 63M J 560 63M J 1.0K 63M J 10K 63M J 10K 63M J 10K 63M J
REMARKS ROM2 64M REGULATOR +9V REGULATOR +3.3V DRAM 4M OP AMP REGULATOR +5V OP AMP SYSTEM RESET DAC OP AMP OP AMP BILATERAL SWITCH REGULATOR +5V INVERTER D-FF BUS-TRANSCEIVER DECODER INVERTER SIO4 OR D-FF OR PHONE OUTPUT L/MONO, OUTPUT R, FOOT CONTROLLER, FOOT SW MIDI IN MIDI THRU/MIDI OUT DC-IN
QTY RANK 10 03 03 03 05 03 04 07 03 02 01 02 04 01 01 03 01 01 06 01 01 01 01 01 01 03 04 02 03 01 01 01 01 01 01 01 01 01 05 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
: New parts
12
S08
REF NO. PART NO. DESCRIPTION -0031 R0032 R0033 R0034 R0035 R0036 R0037 R0038 R0039 R0040 R0041 R0042 R0043 R0044 R0045 R0046 R0047 R0048 R0049 R0050 R0051 R0052 R0053 R0054 R0055 -0058 R0059 R0060 R0061 R0062 R0063 R0065 R0066 R0068 R0069 R0070 R0071 R0073 R0074 R0075 R0076 R0077 R0078 R0079 R0080 R0081 R0083 R0084 R0085 R0086 R0087 R0090 R0091 R0092 R0093 R0099 R0100 R0101 R0102 R0103 R0104 R0109 R0113 R0114 -0119 R0125 R0128 R0129 -0132 R0133 -0135 R0136 R0137 R0138 -0140 RD357100 RD357120 RD357120 RD350000 RD357470 RD350000 RD357470 RD357220 RD357220 RD356680 RD356680 RD355100 RD355100 RD358100 RD358100 RD356100 VI197400 VI197400 RD356100 RD358100 RD358100 RD357470 RD355220 RD358100 RD357100 RD357100 RD355100 RD357100 RD356100 RD357100 RD357100 RD357470 RD357470 RD356680 RD354470 RD357100 RD356680 RD356680 RD356680 RD358100 RD358100 RD356100 RD356100 RD155470 RD357100 RD256150 RD357100 RD357220 RD357220 RD358100 RD358100 RD359100 RD357100 RD357100 RD350000 RD354680 RD354680 RD356270 RD356100 RD358100 RD357220 RD357220 RD357220 RD357100 RD357100 RD356100 RD254100 RD155120 RD155120 RD357100 RD357100 RD354680 RD354680 RD357100 RD357100 Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) 10K 63M J 12K 63M J 12K 63M J 0 63M J 47K 63M J 0 63M J 47K 63M J 22K 63M J 22K 63M J 6.8K 63M J 6.8K 63M J 100 63M J 100 63M J 100K 63M J 100K 63M J 1.0K 63M J 10.0K 1/10 D 10.0K 1/10 D 1.0K 63M J 100K 63M J 100K 63M J 47K 63M J 220 63M J 100K 63M J 10K 63M J 10K 63M J 100 63M J 10K 63M J 1.0K 63M J 10K 63M J 10K 63M J 47K 63M J 47K 63M J 6.8K 63M J 47 63M J 10K 63M J 6.8K 63M J 6.8K 63M J 6.8K 63M J 100K 63M J 100K 63M J 1.0K 63M J 1.0K 63M J 470.0 1/4 J 10K 63M J 1.5K 0.1 J 10K 63M J 22K 63M J 22K 63M J 100K 63M J 100K 63M J 1.0M 63M J 10K 63M J 10K 63M J 0 63M J 68 63M J 68 63M J 2.7K 63M J 1.0K 63M J 100K 63M J 22K 63M J 22K 63M J 22K 63M J 10K 63M J 10K 63M J 1.0K 63M J 10.0 0.1 J 120.0 1/4 J 120.0 1/4 J 10K 63M J 10K 63M J 68 63M J 68 63M J 10K 63M J 10K 63M J
REMARKS
: New parts
13
S08
REF NO. PART NO. DESCRIPTION R0141 R0142 R0145 SW001 TH001 TR001 TR002 TR003 TR004 X0001 X0002 ZD001 RD355220 RD355220 RD354680 VP691000 VV111400 VD303700 VD303700 VJ927200 VD303700 VZ703600 VY681200 VU171500 VZ705300 VB390500 VB390800 VB941200 -V7411800 XR632A00 VB390400 VB390500 VB390800 VB941200 -FG644100 FG644100 VF760000 VI653000 VD041700 VD041700 HF759100 HF755100 HF755100 HF756100 VU483500 V6760100 US145100 US145100 VF283300 XN859A00 RD356220 RD357910 RD356220 RD356220 RD355200 RD354680 VR346900 V8626000 V8626100 V8893800 VA078900 -FG644100 UI537100 FG644100 FG644100 VE352600 VK024800 VB858500 VK026500 VB390400 VB941200 VB941200 V6341400 IR027350 IR024550 IR027350 IR003250 V6309000 VU067800 V6309000 Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Push Switch Poly Switch Transistor Transistor Transistor Transistor Quartz Crystal Unit Ceramic Resonator Zener Diode Circuit Board Connector Base Post Connector Base Post Diode Dust Proof Cloth Circuit Board IC Connector Base Post Connector Base Post Connector Base Post Diode Dust Proof Cloth Electrolytic Cap.-F Electrolytic Cap.-F Electrolytic Cap.-KS Ceramic Resonator Jumper Wire Jumper Wire Carbon Resistor Carbon Resistor Carbon Resistor Carbon Resistor Resistor Array Circuit Board Ceramic Capacitor-F (chip) Ceramic Capacitor-F (chip) Connector Base Post IC Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Thermistor Circuit Board Circuit Board Circuit Board Jumper Wire Angle, RE Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Connector Base Post Wire Trap Connector Base Post Wire Trap Connector Base Post Diode Diode Rotary Encoder IC IC IC IC LED Yellow LED Red LED Yellow 220 63M J 220 63M J 68 63M J SDDLB1 SMD075-2 SMD 2SC3326 A,B TE85R 2SC3326 A,B TE85R 2SA1162 O,Y 2SC3326 A,B TE85R 8.4672M SMD-49 8M CSTCC8.00MG UDZ 3.6BTE-17 3.6V GH-D_SW H PH- 9P TE PH-12P TE 1SS133,1SS176
REMARKS
STANBY/ON
(VU45980) HE-D_SW L YMZ702-D PH- 8P TE PH- 9P TE PH-12P TE 1SS133,1SS176 0.0100 50V Z 0.0100 50V Z 100.00 10.0V CST4.00MGW040 0.55 0.55 1.0M 1/4 J 100.0 1/4 J 100.0 1/4 J 1.0K 1/4 J RGLD12X103J LC 0.1000 25V Z 0.1000 25V Z PH-15P TE LC7985ND 2.2K 63M J 91K 63M J 2.2K 63M J 2.2K 63M J 200 63M J 68 63M J ERTD2FGJ801S 800 SW VOL KB 0.55 0.0100 50V Z 10.00 16.0V 0.0100 50V Z 0.0100 50V Z PH-14P TE 52147 4P TE PH- 6P SE 52151 6P SE PH- 8P TE 1SS133,1SS176 1SS133,1SS176 XRE0121PVB15FINB1 SN74HC273N SN74HC245N SN74HC273N SN74HC32N SEL6710K TP5 SEL6210S-TP5 SEL6710K TP5 (XZ147B0) (XT240A0) KSN2 10 09 01 03 01 01 01 01 01 01
(VU45960)
C1 -3 C5 CL1 J1 J2 R1 R2 R3 R4 RA1
01 01 01 01 01 08 01 01 01 06 01 01 01 01 01 01 03
C0001 C0002 CN001 IC001 R0001 R0002 R0003 -0006 R0007 R0008 TH001 J 10 C0001 C0002 C0003 -0006 CN001 CN002 CN003 CN004 CN005 D0001 -0005 EC001 IC002 IC003 IC004 IC005 LD001 LD002 LD003
LCD CONTROLLER
Data Dial D-FF TRANSCEIVER D-FF OR VOICE EDIT MULTI, SEQ PLAY, PRESET
: New parts
14
S08
REF NO. PART NO. DESCRIPTION -007 LD008 RA001 R0001 -0008 R0009 -0016 SW001 SW002 SW003 SW004 SW005 SW006 SW007 SW008 -018 SW019 -022 SW023 -035 VR001 C0001 C0002 C0003 C0004 C0005 C0006 C0007 C0008 C0009 C0010 C0011 C0012 -0017 C0018 C0019 C0020 C0021 C0022 C0023 CN001 CN002 CN005 EM001 IC001 IC002 IC002 IC003 IC003 IC004 IC005 IC006 IC006 IC007 IC007 IC008 L0001 RA001 RA002 RA003 RA004 RA005 RA006 RA007 RA008 RA009 -0013 R0002 R0004 R0005 R0006 R0007 V6309000 VU067800 VE445200 HF456470 HF456470 HF455390 HF455390 VV439800 VZ085500 VV439800 VV439800 VZ085500 VZ085500 VV439800 VZ085500 VZ085500 VV439800 VV439800 VZ085500 VZ085500 VL445700 V8395300 -UF037100 US061220 US061220 US064100 US062680 US135100 UF037100 US064100 US035100 UF066220 UF037100 US064100 US064100 US061470 US064100 UF037100 US064100 UF037100 US064100 V6802600 V3962800 VQ048500 V6196600 X2886100 XR337A00 XY306A00 XR337A00 XY306A00 XM332A00 XV242A00 IS024400 XT800A00 IS027300 XN971A00 XZ372A00 V5239100 RE047220 RE047220 RE044680 RE044680 RE048100 RE048100 RE044680 RE044680 RE047220 RE047220 RD356470 RD357220 RD357220 RD355680 RD356100 LED Yellow LED Red Resistor Array Carbon Resistor Carbon Resistor Carbon Resistor Carbon Resistor Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Tact Switch Slide Variable Resistor Circuit Board Angle, US Electrolytic Cap. (chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-F (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Electrolytic Cap. (chip) Ceramic Capacitor-B (chip) Jack Connector Assembly Connector Assembly EMI Filter (chip) IC IC IC IC IC IC IC IC IC IC IC IC Common Mode Coil Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) SEL6710K TP5 SEL6210S-TP5 RGLD8X103J 4.7K 1/4 J 4.7K 1/4 J 390.0 1/4 J 390.0 1/4 J SKQNAJ SKQNAM004A SKQNAJ SKQNAJ SKQNAM004A SKQNAM004A SKQNAJ SKQNAM004A SKQNAM004A SKQNAJ SKQNAJ SKQNAM004A SKQNAM004A A10K EWA-NNDCH1A14 US 1 10 16V 22P 50V J 22P 50V J 0.0100 50V K 680P 50V J 0.1000 16V Z 10 16V 0.0100 50V K 0.1000 16V K 2.2 50V 10 16V 0.0100 50V K 0.0100 50V K 47P 50V J 0.0100 50V K 10 16V 0.0100 50V K 10 16V 0.0100 50V K USB 4P SE CN015R-3013-0 FFC 52045 36P TE NFM4516P13C204FT1 M37640M8-152 FP TC74VHC32F-TEL 74VHC32SJX TC74VHC32F-TEL 74VHC32SJX TC74VHC04F TC74VHCT245AF HD74LV244AFPEL TC74VHC244F HD74LV273AFPEL TC74VHC273F TC74VHCT32AFT-EL PLP3216S121SL2T1 22KX4 22KX4 68X4 68X4 100KX4 100KX4 68X4 68X4 22KX4 22KX4 4.7K 63M J 22K 63M J 22K 63M J 680 63M J 1.0K 63M J
QTY RANK 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 03
VOICE UTILITY EDIT MULTI CONTROLLER JOB SEQ PLAY CARD, STORE, (+), (-), DEC/NO Q, H, G, MUTE, INC/YES, W CATEGORY SEARCH, PRESET, USER, GM2/XG 7, 4, 1, 0, 8, 5, 2, (-), 9, 6, 3, ENTER, EXIT VOLUME (X2190B0) (V859940)
USB
CPU(USB 32K)
}OR OR }OR OR } }
INVERTER TRANSCEIVE BUFFER BUFFER D-FF D-FF OR
: New parts
15
S08
REF NO. PART NO. DESCRIPTION R0008 R0009 R0010 R0011 R0012 R0013 R0014 R0015 R0016 R0017 -0019 R0020 -0022 R0023 -0025 R0026 -0028 R0029 R0030 -0032 TR001 X0001 RD356100 RD355150 RD357100 RD154330 RD357220 RD154330 RD155470 RD358100 RD356150 RD357100 RD357100 RD355100 RD355100 RD358470 RD358470 RD357100 RD357100 RD355100 RD357100 RD357100 VJ927200 VP864900 Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Transistor Quartz Crystal Unit 1.0K 63M J 150 63M J 10K 63M J 33.0 1/4 J 22K 63M J 33.0 1/4 J 470.0 1/4 J 100K 63M J 1.5K 63M J 10K 63M J 10K 63M J 100 63M J 100 63M J 470K 63M J 470K 63M J 10K 63M J 10K 63M J 100 63M J 10K 63M J 10K 63M J 2SA1162 O,Y 16M SMD-49 CR2032 TSB0794-DGTDCN-C1 A PT RK1631110T54A 10K 10.0K K161100S
REMARKS
QTY RANK 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 04
VN103500 Lithium Battery V 8 6 2 4 3 0 0 LCD V 5 2 6 4 9 0 0 Back Light Assembly VQ764300 Rotary Variable Resistor VN245400 Rotary Variable Resistor
: New parts
16
A US 1
H
S08
or CONSIDERABLE PARTS.
TRANSCEIVER
CONNECT DM CN7 1 2
US CN5 36 35
35 36
2 1
BUFFER
OR D-FF
5
INVERTER INVERTER OR OR
OR
OR
6
INVERTER
28CC1-8821929
S08
S08
A SW 1
H
S08
D-FF
TRANSCEIVER
D-FF
from DM-CN6
OR
OR
CATEGORY SEACH 7 8 9
ROTARY ENCODER
PIANO ORGAN GUITAR
4
from DM-CN2
VOICE
MULTI
MUTE
PRESET
COMMON
DRUM/PERC
BASS
STRINGS
BRASS
UTILITY
CONTROLLER
CARD
DEC/NO
INC/YES
USER
SE
REED/PIPE
SYN LEAD
SYN PAD
5
EDIT JOB
STORE GM2/XG 0 OTHER COMPARE PLAY/STOP SYN COMP CHROMATIC PERCUSSION KEYBOARD ENTER EXIT
6
28CC1-8821928
S08 S08
S08
1 1
DM
2
DRAM 4M
OP AMP
to LCD-CN1
Pattern Side
DECODER
ROM1 64M
5
INVERTER
Pattern Side
to SW-CN2
to US-CN5
Pattern Side
Components Side
ROM2 64M
7
to SW-CN1
REGULATOR +9V
Pattern Side
OR
8
C161, and C162 and C163 are a sake for combination.
OR
DC-IN
SRAM LOWER
For 1 Mbit SRAM WORK
REGULATOR +5V INVERTER D-FF REGULATOR +3.3V BILATERAL SWITCH SYSTEM RESET INVERTER OR
TRANSCEIVER OR OR
10
10
28CC1-8817390 11
VOL
2MIN 2C 1C 1MIN FG FG 1MIN 2MIN
2 1 3
1: V in 2: GND 3: V out
2
1
11
28CC1-8821928
1 3
1: V in 2: GND 3: V out
3 5 2 4
KB
to HE-D_SW L
11
1: OUTPUT 2: COMMON 3: INPUT
12
28CC1-8821928 S08
A B C D E F G H I J K L M N O P Q
12
S08
S08
1 1
GH-D_SW H
28CC1-8811214 4
HE-D_SW L
5 5
28CC1-8811214 4
7
LC
to KB-CN5
LCD CONTROLLER
8
LCD
to DM-CN4
9
RE WH
28CC1-8817393 2
10 10
11
11
12
12
S08
A B C D E F G H I J K L M N O P
S08
Q