You are on page 1of 9

Vaporliquid separator

From Wikipedia, the free encyclopedia

A typical vaporliquid separator including commonly a de-entrainment pad and sometimes an inlet distributor

A vaporliquid separator is a device used in several industrial applications to separate a vaporliquid mixture. For the common variety, gravity is utilized in a vertical vessel to cause the liquid to settle to the bottom of the vessel, where it is withdrawn.[1][2][3][4] In low gravity environments such as a space station, a common liquid separator will not function because gravity is not usable as a separation mechanism. In this case, centrifugal force needs to be utilized in a spinning centrifugal separator to drive liquid towards the outer edge of the chamber for removal. Gaseous components migrate towards the center. The gas outlet may itself be surrounding by a spinning mesh screen or grating, so that any liquid that does approach the outlet strikes the grating, is accelerated, and thrown away from the outlet.
Contents
[hide]

1 Method of operation

1.1 Liquid level monitoring

2 Where vaporliquid separators are used

3 Preventing pump damage 4 See also 5 References 6 External links

[edit]Method

of operation

The vapor travels through the gas outlet at a design velocity which minimizes the entrainment of any liquid droplets in the vapor as it exits the vessel. The feed to a vaporliquid separator may also be a liquid that is being partially or totally flashed into a vapor and liquid as it enters the separator. A vaporliquid separator may also be referred to as a flash drum, knock-out drum, knock-out pot, compressor suction drum or compressor inlet drum. When used to remove suspended water droplets from streams of air, a vapor-liquid separator is often called a demister.
[edit]Liquid

level monitoring

The separator is only effective as long as there is an air space inside the chamber. The separator can fail if either the mixed inlet is overwhelmed with supply material, or the liquid drain is unable to handle the volume of liquid being collected. The separator may therefore be combined with some other liquid level sensing mechanism such as a sight glass orfloat sensor. In this manner, both the supply and drain flow can be regulated to prevent the separator from becoming overloaded.
[edit]Where

vaporliquid separators are used

Vaporliquid separators are very widely used in a great many industries and applications, such as:

Oil refineries Natural-gas processing plants Petrochemical and chemical plants Refrigeration systems Air conditioning Compressor systems Gas pipelines Steam condensate flash drums Geothermal power plants

Combined cycle power plants Flare stacks Soil vapor extraction Paper mills

[edit]Preventing

pump damage

In refrigeration systems, it is common for the system to contain a mixture of liquid and gas, but for the mechanical gas compressor to be intolerant of liquid. Some compressor types such as the scroll compressor use a continuously shrinking compression volume. Once liquid completely fills this volume the pump may either stall and overload, or the pump chamber may be warped or otherwise damaged by the fluid that can not fit into a smaller space.
[edit]See

also

Flash evaporation
From Wikipedia, the free encyclopedia

A typical flash drum

Flash (or partial) evaporation is the partial vapor that occurs when a saturated liquid stream undergoes a reduction in pressure by passing through a throttling valve or other throttling device. This process is one of the simplest unit operations. If the throttling valve or device is located at the entry into a pressure vessel so that the flash evaporation occurs within the vessel, then the vessel is often referred to as a flash drum.[1][2] If the saturated liquid is a single-component liquid (for example, liquid propane or liquid ammonia), a part of the liquid immediately "flashes" into vapor. Both the vapor and the residual liquid are cooled to the saturation temperature of the liquid at the reduced pressure. This is often referred to as "auto-refrigeration" and is the basis of most conventional vapor compression refrigerationsystems. If the saturated liquid is a multi-component liquid (for example, a mixture of propane, isobutane and normal butane), the flashed vapor is richer in the more volatile components than is the remaining liquid. Uncontrolled flash evaporation can result in a boiling liquid expanding vapor explosion (BLEVE).
Contents
[hide]

1 Flash evaporation of a single-component liquid 2 Equilibrium flash of a multi-component liquid 3 Contrast with spray drying 4 See also 5 References 6 External links

[edit]Flash

evaporation of a single-component liquid

The flash evaporation of a single-component liquid is an isenthalpic process and is often referred to as an adiabatic flash. The following equation, derived from a simple heat balance around the throttling valve or device, is used to predict how much of a single-component liquid is vaporized.

where: = weight fraction vapourized = upstream liquid enthalpy at upstream temperature and pressure, J/kg = flashed vapor enthalpy at downstream pressure and corresponding saturation temperature, J/kg = residual liquid enthalpy at downstream pressure and corresponding saturation temperature, J/kg

If the enthalpy data required for the above equation is unavailable, then the following equation may be used.

where: = weight fraction vapourized = liquid specific heat at upstream temperature and pressure, J/(kg C) = upstream liquid temperature, C = liquid saturation temperature corresponding to the downstream pressure, C = liquid heat of vaporization at downstream pressure and corresponding saturation temperature, J/kg

Here, the words "upstream" and "downstream" refer to before and after the liquid passes through the throttling valve or device. This type of flash evaporation is used in the desalination of brackish water or ocean water by "Multi-Stage Flash Distillation." The water is heated and then routed into a reduced-pressure flash evaporation "stage" where some of the water flashes into steam. This steam is subsequently condensed into salt-free water. The residual salty liquid from that first stage is introduced into a second flash evaporation stage at a pressure lower than the first stage pressure. More water is flashed into steam which is also subsequently condensed into more salt-free water. This sequential use of multiple flash evaporation stages is continued until the design objectives of the system are met. A large part of the world's installed desalination capacity uses multi-stage flash distillation. Typically such plants have 24 or more sequential stages of flash evaporation.
[edit]Equilibrium

flash of a multi-component liquid

The equilibrium flash of a multi-component liquid may be visualized as a simple distillation process using a single equilibrium stage. It is very different and more complex than the flash evaporation of single-component liquid. For a multi-component liquid, calculating the amounts of flashed vapor and residual liquid in equilibrium with each other at a given temperature and pressure requires a trial-and-error iterative solution. Such a calculation is commonly referred to as an equilibrium flash calculation. It involves solving the Rachford-Rice equation:[3][4][5][6]

where:

zi is the mole fraction of component i in the feed liquid (assumed to be known); is the fraction of feed that is vaporised; Ki is the equilibrium constant of component i.

The equilibrium constants Ki are in general functions of many parameters, though the most important is arguably temperature; they are defined as:

where:

xi is the mole fraction of component i in liquid phase; yi is the mole fraction of component i in gas phase.

Once the Rachford-Rice equation has been solved for , the compositions xi and yi can be immediately calculated as:

The Rachford-Rice equation can have multiple solutions for , at most one of which guarantees that all xi and yi will be positive. In particular, if there is only one for which:

then that is the solution; if there are multiple such 's, it means that either Kmax<1 or Kmin>1, indicating respectively that no gas phase can be sustained (and therefore =0) or conversely that no liquid phase can exist (and therefore =1). It is possible to use Newton's method for solving the above water equation, but there is a risk of converging to the wrong value of ; it is important to initialise the solver to a sensible initial value, such as (max+min)/2 (which is however not sufficient: Newton's method makes no guarantees on stability), or, alternatively, use a bracketing solver such as thebisection method or the Brent method, which are guaranteed to converge but can be slower.

The equilibrium flash of multi-component liquids is very widely utilized in petroleum refineries, petrochemical and chemical plants and natural gas processing plants.
[edit]Contrast

with spray drying

Spray drying is sometimes seen a form of flash evaporation. However, although it is a form of liquid evaporation, it is quite different from flash evaporation. In spray drying, a slurry of very small solids is rapidly dried by suspension in a hot gas. The slurry is first atomized into very small liquid droplets which are then sprayed into a stream of hot dry air. The liquid rapidly evaporates leaving behind dry powder or dry solid granules. The dry powder or solid granules are recovered from the exhaust air by usingcyclones, bag filters or electrostatic precipitators.
[edit]See

also

Evaporator Vapor-liquid separator

[edit]References

1.

^ Stanley M. Walas (1988). Chemical Process Equipment:Selection and Design. Butterworth- Heinemann. ISBN 0-409-90131-8.

2.

^ Gas Processing Suppliers Association (GPSA) (1987). Engineering Data Book (10th Edition, Vol. 1 ed.). Gas Processing Suppliers Association, Tulsa, Oklahoma.

3.

^ Harry Kooijman and Ross Taylor (2000). The ChemSep Book (2nd ed.). ISBN 38311-1068-9. See page 186.

4. 5.

^ Analysis of Objective Functions (Pennsylvania State University) ^ Flash Calculations using the Soave-Redlich-Kwong equation of state (view fullsize image)

6.

^ Curtis H. Whitson, Michael L. Michelsen, The Negative Flash, Fluid Phase Equilibria, 53 (1989) 5171.

[edit]External

links

Vapor and Flash Steam Animation, photos and technical explanation of the difference between Flash Steam and Vaporized fraction.

Flash Steam Tutorial The benefits of recovering flash steam, how it is done and typical applications.

Water Desalination Technologies in the Middle East and Western Asia Discussion of spray drying Flash evaporation program online Flash distillation of the hydrocarbon compounds.

You might also like