Professional Documents
Culture Documents
Memory
Actual Processor
Data Lines
Program
Registers
Control Lines
Data
Teknik Elektro Udayana 2
Page 1
Computer modules
Address Bus
CPU
Peripherals (IO)
Page 2
Beberapa Istilah
Active HIGH, Active LOW, Enable, Disable, ON, OFF, EMPTY, NONE, Logika 0, Logika 1, Not Install, Install
X 0
X 1
Teknik Elektro Udayana 5
JUMPER
OFF Disable Logika 0 Not Install
Page 3
Pengertian / Perjanjian / Kesepakatan Active HIGH Active LOW Saat Active Logika 1 Saat Active Logika 0
MN/MX
Page 4
Pengertian
Mikroprosesor
Output
Mikroprosesor
Input
Mikroprosesor
Output / Input
Teknik Elektro Udayana 9
8088 Microprocessor
Minimum Mode
Page 5
Pin Configuration
Pin Configuration
MN / MX READY CLK RESET TEST HLDA A8 HOLD NMI A9 A10 A11 A12 A13 A14 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7
8088
INTR
INTA
Page 6
Address Pins
Page 7
Data Pins
AD0..AD7
Control Pins
MN/MX (input)
Indicates what mode the processor is to operate in
READY (input)
When given an input LOW, it will go into a wait state
CLK (input)
Provides basic timing for the processor
RESET (input)
Causes the processor to immediately terminate its present activity To reset the microprocessor, this must be HIGH for at least 4 clock cycles
Teknik Elektro Udayana 16
Page 8
Control Pins
TEST (input)
Connect this to HIGH
HOLD (input)
Connect this to LOW
HLDA (output)
Control Pins
INTR (input)
Interrupt request
INTA (output)
Interrupt Acknowledge
NMI (input)
Non-maskable interrupt
Page 9
Control Pins
DEN (output)
Data Enable It is LOW when processor wants to receive data or processor is giving out data
DT/R (output)
Data Transmit/Receive When HIGH, direction of data lines is from microprocessor to memory/devices When LOW, direction of data lines is from memory/devices to microprocessor
IO/M (output)
Device/Memory When HIGH, microprocessor wants to access I/O Device When LOW, microprocessor wants to access memory
Control Pins
RD (output)
When LOW, it indicates that the microprocessor is performing a read access
WR (output)
When LOW, it indicates that the microprocessor is performing a write access
ALE (output)
Address Latch Enable Provided by the microprocessor to latch address When this is HIGH, microprocessor is using AD0..AD7, A19/S6, A18/S5, A17/S4, A16/S3 as address lines
Page 10
Clock Signal
needed by the microprocessor to synchronize signals ideally a square wave having a constant frequency
8086 Signals
Page 11
Software Pendukung
PROTEL10.SCH PROTEL15.PCB
Tugas Tanggal 19 November 2007 ( Tidak ada Kuliah ) Mencari Data sheet IC sbb:
8088, 8086, 8284, 244, 245, 373, 374, 2704, 2708, 2716,2732, 2764, 27128, 27256, 27215, 271024, 4016, 62256, 138, 139, 168, 7400, 7404, 7408, 7410, 7430, 636, 2142, 8279, 8288, 8085, 8254, 8255,
Teknik Elektro Udayana 24
Page 12
Page 13